Engineering Commons^™

Simulation Study On Effect Of Gas Charging And Egr In A Dual-Fuel Engine, Satyavenkata Naga Sai Sharath Gorthy

Dissertations, Master's Theses and Master's Reports

Natural gas combined with diesel as micro pilot has the capabilities of achieving lower NOx and soot emissions. Optimization of the combustion process in engines with natural gas and diesel micro-pilot is essential to achieve higher efficiencies and loads. Gas charging (intake air boosting) and EGR are two technologies which when implemented in the natural gas-diesel engines, provide the opportunity to achieve higher efficiencies and loads and low emissions. Simulation study is one of the approaches to investigate the extent and effects of gas charging and EGR on the performance of the engine. With the rapid improvements over the past …

Simulation Of Human Ankle Trajectory During Stance Phase Of Gait, Leslie Castelino

Dissertations, Master's Theses and Master's Reports

A simulation was developed which mimics the human gait characteristics based on the input of an individual’s gait trajectory. This simulation also estimates the impedance of the human ankle based on the ground reaction forces measured by the force plate. This simulation will accept alterations of the following parameters: total body weight, weight of the shank, weight of the foot, trajectories of the shank and foot of the individual and orientation of the force plate, which would generate a new gait trajectory for the ankle during the stance phase of gait. The goal of this simulation was to validate the …

Autonomous Driving With A Simulation Trained Convolutional Neural Network, Cameron Franke

University of the Pacific Theses and Dissertations

Autonomous vehicles will help society if they can easily support a broad range of driving environments, conditions, and vehicles.

Achieving this requires reducing the complexity of the algorithmic system, easing the collection of training data, and verifying operation using real-world experiments. Our work addresses these issues by utilizing a reflexive neural network that translates images into steering and throttle commands. This network is trained using simulation data from Grand Theft Auto V~\cite{gtav}, which we augment to reduce the number of simulation hours driven. We then validate our work using a RC car system through numerous tests. Our system successfully drive …

Formation Flight For Fuel Saving In Coronet Missions Of Kc-135r And F-15c/E, Christopher Allen Kniffin

Mechanical and Aerospace Engineering Theses - Archive

The fuel saving benefit of formation flight has been demonstrated through theoretical and computational analyses, simulation, wind tunnel and flight tests. When an aircraft flies in a specific region in the wake of another aircraft, it experiences upwash, which results in reduced drag and thus reduced thrust requirement. One specific USAF mission that can potentially benefit from formation flight is coronet missions. In a coronet mission, fighter aircraft are escorted and refueled, as needed, by tanker aircraft over a long range. During the flight, the receiver aircraft fly in formation with the tanker but outside of the wake of the …

Adaptive Sampling Trust-Region Methods For Derivative-Based And Derivative-Free Simulation Optimization Problems, Sara Shashaani

Open Access Dissertations

We consider unconstrained optimization problems where only “stochastic” estimates of the objective function are observable as replicates from a Monte Carlo simulation oracle. In the first study we assume that the function gradients are directly observable through the Monte Carlo simulation. We propose ASTRO, which is an adaptive sampling based trust-region optimization method where a stochastic local model is constructed, optimized, and updated iteratively. ASTRO is a derivative-based algorithm and provides almost sure convergence to a first-order critical point with good practical performance. In the second study the Monte Carlo simulation is assumed to provide no direct observations of the …

Simulation Modeling For Energy Consumption Of Residential Consumers In Response To Demand Side Management., Prajwal Khadgi

Electronic Theses and Dissertations

Energy efficiency in the electricity distribution system continues to gain importance as demand for electricity keeps rising and resources keep diminishing. Achieving higher energy efficiency by implementing control strategies and demand response (DR) programs has always been a topic of interest in the electric utility industry. The advent of smart grids with enhanced data communication capabilities propels DR to be an essential part of the next generation power distribution system. Fundamentally, DR has the ability to charge a customer the true price of electricity at the time of use, and the general perception is that consumers would shift their load …

Predicting The Performance Of Queues: A Data Analytic Approach, Kum Khiong Yang, Cayirli Tugba, Mei Wan Low

Research Collection Lee Kong Chian School Of Business

Existing models of multi-server queues with system transience and non-standard assumptions are either too complex or restricted in their assumptions to be used broadly in practice. This paper proposes using data analytics, combining computer simulation to generate the data and an advanced non-linear regression technique called the Alternating Conditional Expectation (ACE) to construct a set of easy-to-use equations to predict the performance of queues with a scheduled start and end time. Our results show that the equations can accurately predict the queue performance as a function of the number of servers, mean arrival load, session length and service time variability. …

Evaluating Alternative Scheduling Rules To Improve Scheduling Performance, Bryan Allan White

Theses and Dissertations

In this study a powder painting production line was examined for the purpose of improving on its scheduling. A simulation model was developed to compare the performance of alternative scheduling rules. The simulation model utilized scheduling data from the original system in order to determine how accurately it represented the original system. The model was built using the discrete event simulation software Arena. The validated model was used to test a set of scheduling rules that would change the sequence in which orders in the queue were processed. By looking at the different rules and the effects on the final …

Bearing Boundary Element Method Based On Geometrically Similar Roller Conditions, Xia Yang, Ya-Chao Li, Chuang Yan, Guang-Ming Liu, Jian-Mei Wang, Hai-Lian Gui

Journal of Marine Science and Technology–Taiwan

To solve the three-dimensional pressure and load distribution of roller bearings, a new boundary element method (BEM) is presented in this report. First, a discrete model of the initial location roller was established, and the other rollers’ discrete data could be obtained using geometrically similar conditions of this model. Based on the three-dimensional elastic contact BEM, all of the bearing rollers could be described as one object; therefore, the roller bearing problem of a multi-object contact system could be simplified as the problem of a threeobject contact system. Bearing boundary elements were used to realize the discontinuous traction on the …

Modelling The Softening Behaviour During Galvanizing Of Various Steel Grades, Kevin Banks, Rorisang Maubane, Thabang Makwena

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Thermodynamic Simulation For Solidification Path In Die Casting Alloy Development, Mohamad Rusydi Mohamad Yasin, Dongke Sun, Qingyou Han

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Simulation For Carbon Nanotube Dispersion And Microstructure Formation In Cnts/Mg Composite Fabricated With Ultrasonic Processing, Yuansheng Yang, Fuze Zhao, Shaozhen Zhu, Xiaohui Feng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modelling The Softening Behaviour During Galvanizing Of Various Steel Grades, Kevin Banks, Rorisang Maubane, Thabang Makwena

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Temperature Distributions Influencing Lateral Spread In Industrial Hot Rolling, Baohui Tian, Siegfried Kleber, Silvia Zinner, Peter Markiewicz

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

The Simulation For Ultrasonic Testing Based On Frequency-Phase Coded Excitation, Jiaying Zhang, Wenlong Tian, Tie Gang, Sen Cong, Zhaoyang Sheng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Study On Growth Model Of Cellular Automata Method In Solidification Simulation, Zhao Guo, Jian-Xin Zhou, Ya-Jun Yin, Chang-Chang Liu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Integration Of Advanced Simulation And Visualization For Material Processing, Chenn Zhou

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Optimizing The Telescope Assembly Alignment Simulator For Sofia, Zoe E. Sharp, Alex Quyenvo, Jennifer Briggs, Brian Eney

STAR Program Research Presentations

The Stratospheric Observatory for Infrared Astronomy (SOFIA) conducts research on a modified Boeing 747sp aircraft. By using a variety of infrared science instruments mounted on a 2.7 meter telescope, researchers can make discoveries about the galactic center, star formation, and various topics associated with a deeper understanding of our universe. To efficiently collect data through the SOFIA instruments, the instruments must be tested and prepared prior to being placed on the aircraft. Therefore, with the use of the Telescope Assembly Alignment Simulator (TAAS), researchers can design and construct improvements needed for these instruments to efficiently perform while in flight. The …

Metamodels Of Residual Stress Buildup For Machining Process Modeling, Stuart B. Mccrorie, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the process of machining materials, stresses, called residual stresses, accumulate in the workpiece being machined that remain after the process is completed. These residual stresses can affect the properties of the material or cause part distortion, and it is important that they be calculated to prevent complications from arising due to the residual stresses. However, these calculations can be incredibly computationally intensive, and thus other methods are needed to predict the residual stresses in materials for quick decision-making during machining. By using metamodels - a method of representing data where few data points exist - we can achieve an …

Investigation Of Exothermic Reaction Dynamics Via Computational Fluid Dynamics Coupled With A Feedback Controller, Siusan Choi

Mechanical and Aerospace Engineering Dissertations - Archive

The control of reaction temperature under continuous flow conditions is important in a variety of chemical manufacturing industries. For many reactions, operating at off-design temperatures can result in the production of undesired products, reduced feedstock conversion and, in some cases, reduced catalyst lifetime. In many exothermic reactions, maintaining a desired set point temperature at high reactant flow rates becomes challenging if the chemical kinetics exhibit highly non-linear behavior. In these situations, the interaction between commonly used linear controllers and the physical system can lead to unexpected dynamic response and undesired swings in reaction temperature. In this research, a computational model …

Modeling And Simulation Of 1700 V 8 A Genesic Superjunction Transistor, Staci E. Brooks

Graduate Theses and Dissertations

The first-ever 1.7kV 8A SiC physics-based compact SPICE model is developed for behavior prediction, modeling and simulation of the GeneSiC “Super” Junction Transistor. The model implements Gummel-Poon based equations and adds a quasi-saturation collector series resistance representation from a 1.2 kV, 6 A SiC bipolar junction transistor model developed in Hangzhou, China. The model has been validated with the GA08JT17-247 device data representing both static and dynamic characteristics from GeneSiC. Parameter extraction was performed in IC-CAP and results include plots showing output characteristics, capacitance versus voltage (C-V), and switching characteristics for 25 °C, 125 °C, and 175 °C temperatures.

Investigation Of Digital Pump/Motor Control Strategies, Farid El Breidi

Open Access Dissertations

A pump is the heart of fluid power systems, it has a significant impact on the efficiency of many fluid power systems. Motors are the most common rotary actuators in fluid power systems. State-of-the-art pump/motor units can achieve efficiencies higher than 90% when operating at maximum displacement; however, as the displacement drops, the efficiency of these units drops to below 50%. A new digital pump/motor design aims at increasing these efficiencies by utilizing two electrically controlled high speed on/off valves per displacement chamber; these valves provide the ability to achieve variable displacement and allow freedom in choosing operating strategies. Such …

Characterization Of Impact Properties Of Forged, Layered, And Additive Manufactured Titanium Alloy, Melissa Kathryn Matthes

UNLV Theses, Dissertations, Professional Papers, and Capstones

New additive manufactured (AM) materials have the potential of optimizing the geometry and microstructure of complex components to enhance their structural integrity while creating them quickly. However, the behavior of AM materials under extreme dynamic loading conditions is not fully understood. This is especially important in many applications. For example, spacecraft components may be impacted by micrometeorites at hyper velocities of multiple kilometers per second, inducing extreme dynamic loading.

One type of AM material is created by melting and solidifying metal along a specified path. Depending on the geometry, additional streams will be deposited side-by-side. This process affects the microstructure …

Modeling Economic Impacts Of The Inland Waterway Transportation System, Furkan Oztanriseven

Graduate Theses and Dissertations

The inland waterway transportation system of the United States (U.S.) handles 11.7 billion tons of freight annually and connects the heartland of the U.S. with the rest of the world by providing a fuel-efficient and environmentally friendly mode of transportation. This dissertation aims to create decision support tools for maritime stakeholders to measure the economic impacts of the inland waterway transportation systems under real world scenarios including disruptions, demand changes, port expansion decisions, and channel deepening investments. Monte Carlo simulation, system dynamics, discrete-event simulation, agent-based modeling, and multiregional input-output modeling techniques are utilized to analyze the complex relationships between inland …

Fractional Transport Models For Shale Gas In Tight Porous Media, Nadeem A. Malik, Iftikhar Ali

Sixth International Conference on Porous Media and Its Applications in Science, Engineering and Industry

Modelling the flow of fluid through tight porous media, such as unconventional hydrocarbon reservoirs, is very challenging and it is a growing sector and must be addressed. Shale gas is found in such tight porous rocks which are characterized by nano-scale size porous networks with ultra-low permeability [1,2].

Please download the full abstract below.

Flow Of Shale Gas In Tight Rocks Using A Non-Linear Transport Model With Pressure Dependent Model Parameters, Nadeem A. Malik, Iftikhar Ali, Bilal Chanane, Ryad A. Ghanam

Sixth International Conference on Porous Media and Its Applications in Science, Engineering and Industry

A new source of energy has recently been discovered from unconventional hydrocarbon reservoirs, such as shale gas deposits. Shale gas is found in tight porous rocks which are characterised by nano-scale size porous networks with ultra-low permeability [1,2]. The modelling of transport through such tight porous media is very challenging because it is a relatively new discipline and not much is known but transport processes in them, and little data is available; but it is a growing sector and must be addressed. Here, we apply a recently developed non-linear gas transport model [3], to reservoir simulations of single-phase gas through …

Experimental And Numerical Evaluation Of A New Composite Pressure Pipe For A Trenchless Rehabilitation Technology, Xuanchen Yen

Doctoral Dissertations

The information presented in this dissertation is based on research work conducted at Trenchless Technology Center (TTC) at Louisiana Tech University. This work was performed through a contract with China University of Geoscience (CUG) for a gas company. China's gas pipelines need replacement or rehabilitation after 15 to 30 years of service. China's gas industry is looking for suitable techniques to transfer into their market.

When compared to conventional excavation pipeline renewal or replacement methods, there are obvious advantages of TRT for gas pipelines that can impact the triple bottom-line of economic, social and environmental benefits. An introduction of TRT …

A Simulation-Based Layered Framework Framework For The Development Of Collaborative Autonomous Systems, Ioannis Sakiotis

Computational Modeling & Simulation Engineering Theses & Dissertations

The purpose of this thesis is to introduce a simulation-based software framework that facilitates the development of collaborative autonomous systems. Significant commonalities exist in the design approaches of both collaborative and autonomous systems, mirroring the sense, plan, act paradigm, and mostly adopting layered architectures. Unfortunately, the development of such systems is intricate and requires low-level interfacing which significantly detracts from development time. Frameworks for the development of collaborative and autonomous systems have been developed but are not flexible and center on narrow ranges of applications and platforms. The proposed framework utilizes an expandable layered structure that allows developers to define …

Simulation, Measurement, And Emulation Of Photovoltaic Modules Using High Frequency And High Power Density Power Electronic Circuits, Yunas Erkaya

Electrical & Computer Engineering Theses & Dissertations

The number of solar photovoltaic (PV) installations is growing exponentially, and to improve the energy yield and the efficiency of PV systems, it is necessary to have correct methods for simulation, measurement, and emulation. PV systems can be simulated using PV models for different configurations and technologies of PV modules. Additionally, different environmental conditions of solar irradiance, temperature, and partial shading can be incorporated in the model to accurately simulate PV systems for any given condition.

The electrical measurement of PV systems both prior to and after making electrical connections is important for attaining high efficiency and reliability. Measuring PV …

The Development Of A Prosthetic Training Software For Upper Limb Amputees, Tyler Kayne Sullins

USF Tampa Graduate Theses and Dissertations

The purpose of this study was to develop an intuitive software that aids in the field of prosthetic training and rehabilitation by creating an individualized visualization of joint angles. This software is titled “the prosthetic training software (PTS) for individualized joint angle representation”, and it enables the individualized portrayal of predicted or pre-recorded joint angles. The PTS is an intuitive program for clinicians and prosthesis users that produces an animation of a virtual avatar reflecting the user’s segment lengths and amputation for rehabilitation and training purposes.

The PTS consists of a graphical user interface (GUI) and a 3D visualization of …