Engineering Commons^™

Engineering Standards In Highway Design Litigation, Michael Lewyn

Scholarly Works

Highway engineers sometimes believe that if they redesign streets to improve pedestrian safety (for example, by introducing traffic calming techniques) they might be successfully sued for negligent design by motorists. This chapter suggests that in such situations, governments are likely to be protected by discretionary function immunity. In addition, the chapter discusses a variety of technical issues.

Uas Maintenance: A Critical Component In Maintaining Airworthiness, Bettina M. Mrusek, Kristy W. Kiernan, Patti J. Clark

International Journal of Aviation, Aeronautics, and Aerospace

Over the last several decades, the notion of traditional aircraft design has significantly changed. While there are many modern aircraft that resemble earlier models, their components, systems, and overall architecture have evolved, including the introduction of small unmanned aircraft systems (sUAS). Despite the growing consumer attraction to own and operate these aircraft, the subsequent impact on safety is an area of intense concern. The requirement of an established maintenance program for manned aircraft is rooted in ensuring that all aircraft are deemed safe for flight. Preventive maintenance schedules are based on component reliability data, which minimizes unnecessary maintenance while preventing …

Called To Safety? Individual And Combined Effects Of Safety Climate And Occupational Callings On Aviator Safety Performance, Michele W. Gazica, Erin E. Bowen, Michael A. Mccarson, Kristen A-M. Chadwell

Journal of Aviation/Aerospace Education & Research

This study examined the individual and combined effects of two potential antecedents to aviation-related safety performance: safety climate and occupational callings. Research exploring the importance of occupational callings to the safety domain is in its nascent stages. The extent that someone is living a calling may explain variance in actual safety performance above that which can be explained by safety climate alone. Survey data from aviators in a flight training program were analyzed to evaluate the ability of occupational calling assessments to inform the potential for safety mishaps within the aviation industry. Results indicate that both safety climate and occupational …

Improving Workers' Safety And Health In The Zimbabwean Mining And Quarrying Industry, Bernard Mabika

Walden Dissertations and Doctoral Studies

Lack of effective occupational safety and health (OSH) strategies is a reason that

workplace accidents in the mining and quarrying industry remain high, making the

industry one of the riskiest operations worldwide. The purpose of this multiple case study

was to explore successful strategies mining and quarrying leaders in Zimbabwe used to

improve OSH. The key research question addressed successful strategies leaders in the

mining and quarrying industry use to improve employee occupational safety and health in

Zimbabwe. Six successful business leaders from 3 mining and quarrying mines in

Zimbabwe demonstrated an exception to unsafe practices, particularly through their

exceptional …

Building Entry Flood Barrier, Richard Esker, Shannon Mccall, Andrew Udovich, Brian Foust

Williams Honors College, Honors Research Projects

The purpose of this project is to develop a flood barrier that would resist flood water from entering through the doorways of a building. The goal is to mitigate extensive flooding within a structure. After the disastrous weather events that impacted American citizens late in the year of 2017, the team was inspired to develop a project to help disaster victims. Through extensive preliminary and market research, it was discovered that flooding is a serious issue that affects people all over the world. A product to stop flooding could benefit people in developed countries, but it could also help citizens …

Understanding Of Molecular Interactions And Reversibility In Silylamines, Josephine Chen

Dissertations and Theses

Modern Li-ion batteries employ flammable electrolytes that pose safety concerns. Battery safety has become important as several incidents involving Li-ion battery fires have been observed. This issue could be addressed through a switchable battery electrolyte. Reversible ionic liquids (RevILs) could be used in such an electrolyte that would cease operation in the event of rapid temperature elevation because they can switch between states of drastically different properties upon the application of an external stimulus, such as temperature or CO₂ addition. Silylamines, in particular, are a class of thermally responsive RevILs that are conducting in its ionic liquid (RevIL) state …

Uas Pilots Code – Annotated Version 1.0, Michael S. Baum, Kristine Kiernan, Donald W. Steinman, Ryan J. Wallace Ed.D.

Publications

The UAS PILOTS CODE (UASPC) offers recommendations to advance flight safety, ground safety, airmanship, and professionalism.6 It presents a vision of excellence for UAS pilots and operators, and includes general guidance for all types of UAS. The UASPC offers broad guidance—a set of values—to help a pilot interpret and apply standards and regulations, and to confront real world challenges to avoid incidents and accidents. It is designed to help UAS pilots develop standard operating procedures (SOPs), effective risk management,7 safety management systems (SMS), and to encourage UAS pilots to consider themselves aviators and participants in the broader aviation community.

Brain Motion, Deformation, And Potential Injury During Soccer Heading, Charles F. Babbs

Weldon School of Biomedical Engineering Faculty Working Papers

This paper addresses the problem of what is happening physically inside the skull during head-ball contact. Mathematical models based upon Newton’s laws of motion and numerical methods are used to create animations of brain motion and deformation inside the skull.

Initially a 1 cm gap filled with cerebrospinal fluid (CSF) separates the brain from the rigid skull in adults and older children. Whole head acceleration induces a pulse of artificial gravity within the skull. Because brain density differs slightly from that of CSF, the brain accelerates and strikes the inner aspect of the skull, undergoing viscoelastic deformation, ranging from 1 …

The Future Of Nuclear Security In Moroccan Territory After The Creation Of The New Moroccan Agency Of Nuclear And Radiological Safety And Security: Opportunities And Challenges, Amal Touarsi, Amina Kharchaf

International Journal of Nuclear Security

Nowadays, a security regime for protecting nuclear and radiological material—providing an intelligent national regulatory institution and establishing national security laws—is necessary in order for a state to ensure security of nuclear and radiological materials used within its borders.

This paper focuses on discussing the opportunities and challenges facing the future of nuclear security after the creation of the new Moroccan Agency of Nuclear and Radiological Safety and Security.

Effectiveness Of Chain Link Turtle Fence And Culverts In Reducing Turtle Mortality And Providing Connectivity Along U.S. Hwy 83, Valentine National Wildlife Refuge, Nebraska, Usa, Marcel P. Huijser, Kari E. Gunson, Elizabeth R. Fairbank

Nebraska Department of Transportation: Research Reports

We evaluated the effectiveness of existing turtle fences through collecting and analyzing turtle mortality data along U.S. Hwy 83, in and around Valentine National Wildlife Refuge, Nebraska, USA. We also investigated the level of connectivity for turtles provided through the culverts that were originally designed to pass water through a capture-mark-recapture experiment. While fenced valley sections had 33.1% fewer turtle observations than unfenced valley sections, the difference was not significant. However, we think that the effectiveness of the fence can be improved through fence repairs, other modifications of the fences, vegetation maintenance, and extending the length of the fences. Four …

Safety And Organization: An Epics Partnership With Habitat For Humanity, Trevor Drouillard, Logan Quaas, Colleen Kelch, Jeremiah Campbell, Anna Francis, Connor Moore, Jiayin Qi, Alyssa Trobl

Purdue Journal of Service-Learning and International Engagement

The student authors of this essay are a group of eight participating in the Engineering Projects in Community Service (EPICS) program on the Habitat for Humanity (HFH) team. In this article, they describe how they have improved the working conditions within the loft space of the local Habitat for Humanity office in Lafayette, Indiana. Their work is intended to permanently improve the safety conditions of the loft, as well as the organization of the equipment within the loft. The specific safety concerns addressed by the HFH team include horizontal steel trusses at head level and an unprotected access opening in …

Safety Concepts For Workers From An Osha Perspective, Zamaan Al-Shabbani, Roy E. Sturgill Jr., Gabriel B. Dadi

Kentucky Transportation Center Research Report

Highway construction and maintenance workers face numerous hazards on job sites, many of which are unique by industry standards. Despite the exposure of state transportation agency employees and contractors to these hazards, there are few safety standards, regulations, programs that directly target the sector aimed at prevention and mitigation. To help the Kentucky Transportation Cabinet (KYTC) improve employee safety, researchers at the Kentucky Transportation Center (KTC) analyzed the frequency and causes of workplace injuries for 10 essential Cabinet maintenance operations. Most incidents were attributable to human factors or ergonomics. Based on this analysis, the leading causes of incidents, and a …

Increased Span Length For The Mgs Long-Span Guardrail System Part Iii: Failure Analysis, Sagheer A. Ranjha, Robert W. Bielenberg, John D. Reid, Ronald K. Faller

Nebraska Department of Transportation: Research Reports

The objective of this research study was to review and analyze the system failure observed during crash testing of an increased span length for the MGS long-span guardrail system in test no. MGSLS-2. Test no. MGSLS-2 was a full-scale crash test conducted on the MGS long-span guardrail with a span length of 311⁄4 ft (9.5 m). This test utilized universal breakaway steel posts (UBSPs) adjacent to the long span in lieu of the controlled release terminal (CRT) wood posts used in previous long span systems.

An engineering analysis was undertaken to review the downstream end anchorage failure observed in test …

A Hierarchical Modelling Approach For Assessing The Impact Factors Of The Measured Of Mobility And Safety At Intersections, Hiba Eyesha Abou-Kassem

Civil and Environmental Theses

Measuring safety and mobility for various types of intersections is crucial in any transportation study. Many factors contribute to changing the effectiveness of the different types of intersections on mobility and safety. Deciding which type of intersection is most suitable in a particular environ and prevailing traffic conditions depends on the number of crashes, injuries, delay time, etc. This study focuses on two intersection types; signalized intersections and non-signalized intersections (only roundabouts). The aim of this research is to devise a theoretical modeling framework and hence a statistical-based methodology that can be used to assess the safety and mobility measures …

An Alternative Method Of Identification Of A Failed Engine In Twin-Engine Turboprop Aircraft, Andrey Babin, Andrew R. Dattel Ph.D.

National Training Aircraft Symposium (NTAS)

Previous incidents and accidents involving twin-engine aircraft, including the recent TransAsia Flight 235 crash, have revealed that pilots are prone to mistakes in identifying the engine that fails, and subsequently, shutting down the wrong engine, i.e. perfectly working engine. Most accidents of this type happen on takeoff when pilot workload is at its highest level. It may be that the current training procedure for engine failures on takeoff, called identify-verify-feather (IVF), is counterintuitive and may lead to greater confusion. IVF is based on haptic sensory channel, which is known to be less effective than visual channel. This study proposes a …

Radiative Heat Transfer Analysis Of Railroad Bearings For Wayside Hot-Box Detector Optimization, Arthur Mealer, Constantine Tarawneh, Stephen Crown

Mechanical Engineering Faculty Publications

The railroad industry utilizes wayside detection systems to monitor the temperature of freight railcar bearings in service. The wayside hot-box detector (HBD) is a device that sits on the side of the tracks and uses a non-contact infrared sensor to determine the temperature of the train bearings as they roll over the detector. Various factors can affect the temperature measurements of these wayside detection systems. The class of the railroad bearing and its position on the axle relative to the position of the wayside detector can affect the temperature measurement. That is, the location on the bearing cup where the …

Initiating Event Analysis Of A Lithium Fluoride Thorium Reactor, Nicholas Charles Geraci

Engineering Management & Systems Engineering Theses & Dissertations

The primary purpose of this study is to perform an Initiating Event Analysis for a Lithium Fluoride Thorium Reactor (LFTR) as the first step of a Probabilistic Safety Assessment (PSA). The major objective of the research is to compile a list of key initiating events capable of resulting in failure of safety systems and release of radioactive material from the LFTR.

Due to the complex interactions between engineering design, component reliability and human reliability, probabilistic safety assessments are most useful when the scope is limited to a single reactor plant. Thus, this thesis will study the LFTR design proposed by …

Recommendation Of A New Transit Performance Measure In The National Transit Database, Fatemeh Baratian-Ghorghi, Hossein Ahmadianyazdi

Journal of Public Transportation

The frequency of incidents negatively changes public perception with regard to the public safety in transit systems. The level of safety expressed as performance measures, ensures contractors and users that a quality safety level is maintained. Both the private and public sectors in the U.S. annually report accurate data to the National Transit Database (NTD) to be used in assessing the progress of the nation's public transportation systems. Although they must provide both the annual report and monthly reports including Safety and Security data, measures are only grouped into the indicators of efficiency and effectiveness of a system and there …

Wheelieking Trainer Project Report, Harold Hall Iii, Nathaniel Fox, Thomas Niemisto

Biomedical Engineering

In this report we will detail the design and implementation process of the WheelieKing Trainer project, a device that helps people learn how to do wheelies on a bicycle by preventing backward falls. Formal project requirements are specified, followed by the ideation and iteration process to meet those requirements. The components and methods used to create the device are described in detail. The results of the development process and usage test results of the device are included. Appendices at the end of this report include references, supporting analyses, and project management and timeline details.

A Recommendation To Implement "Spanish In Construction" Topics Course, Benjamin W. Dimer

Construction Management

The purpose of this report is to recommend the addition of a Spanish in Construction class to the Construction Management curriculum. Many of Cal Poly’s graduates enter a construction workforce which is composed heavily of Hispanic and Latino members. Historically, Hispanics and Latinos account for not only the most rapidly growing populations of construction, but also the most proportionally at-risk. In an industry as dangerous as construction, it is important that students are well-rounded and well-prepared to contribute as safely, efficiently, and flawlessly as possible. Thorough literature review and an interview of part-time Cal Poly lecturer and industry veteran, Eric …

Evaluation Of Floorpan Tearing And Cable Splices For Cable Barrier Systems, Scott K. Rosenbaugh, Jason A. Hartwell, Robert W. Bielenberg, Ronald K. Faller, James C. Holloway, Karla A. Lechtenberg

Nebraska Department of Transportation: Research Reports

This research effort consisted of two objectives related to components of a prototype cable barrier system. The first objective was to mitigate the potential for vehicle floorpan tearing by modifying the cable guardrail posts. A bogie vehicle was equipped with a simulated floorpan designed to replicate the height, thickness, and strength of the floorpan of a Kia Rio vehicle. Baseline testing demonstrated that the top of the Midwest Weak Post (MWP) would contact, and crease the simulated floorpan, which matched the damage observed in actual full-scale vehicle crash tests. Once the test setup provided the desired results, various post configurations …

Length Of Need And Minimum System Length For F-Shape Portable Concrete Barrier, Robert W. Bielenberg, Dylan T. Meyer, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

Portable concrete barrier (PCB) systems are often used to redirect errant vehicles through a combination of inertial resistance, lateral friction loads, and tensile loads developed from the mass and friction of the barrier segments. State departments of transportation (DOTs) and other end users may wish to utilize minimal length PCB installations to shield a hazard or work zone or limit the number of barriers required on the upstream and downstream ends to reduce overall system length. However, concerns with the performance of shorter PCB installations include increased lateral deflections and working widths and barrier pocketing. Additionally, no impact testing has …

Testing And Evaluation Of Mash Tl-3 Transition Between Guardrail And Portable Concrete Barriers, Robert W. Bielenberg, Jessica L. Lingenfelter, Justine E. Kohtz, Ronald K. Faller, John D. Reid

Nebraska Department of Transportation: Research Reports

Three full-scale vehicle crash tests were conducted according to the Manual for Assessing Safety Hardware (MASH) Test Level 3 (TL-3) safety performance criteria on a transition between the Midwest Guardrail System (MGS) and a portable concrete barrier (PCB) system. The transition system utilized for test nos. MGSPCB-1 through MGSPCB-3 consisted of a standard MGS that overlapped a series of F- shape PCB segments that approached the MGS at a 15H:1V flare. In the overlapped portion of the barrier systems, uniquely-designed blockout holders and a specialized W-beam end shoe mounting bracket were used to connect the systems.

In test no. MGSPCB-1, …

Design Baseline Document: Mini Baja Frame, Michael Luke Scoggins

Undergraduate Honors Capstone Projects

Our objective as the Mini Baja Frame team is to design and implement a prototype vehicle frame that is both cost-effective and competitive in an all-terrain racing environment. This vehicle must be able to endure the trials of the Society of Automotive Engineers (SAE) Mini Baja competition. An effective frame will contribute to the complete Utah State University Mini Baja Team objectives by efficiently integrating the components produced by the drivetrain and the suspension engineers. In addition, this competition is a means for us as students to gain valuable, tangible experience in the engineering design process.

Increased Span Length For The Mgs Long-Span Guardrail System Part Ii: Full-Scale Crash Testing, Dylan T. Meyer, John D. Reid, Karla A. Lechtenberg, Robert W. Bielenberg, Ronald K. Faller

Nebraska Department of Transportation: Research Reports

The objective of this research study was to design and evaluate the MGS long-span design for use with unsupported spans greater than 25 ft (7.6 m). Two full-scale crash tests were conducted to evaluate the MGS long-span system with increased span lengths and the use of UBSP posts adjacent to the long span. Both tests were conducted according to the TL- 3 criteria outlined in MASH. Both test nos. MGSLS-1 and MGSLS-2 were conducted with the 2270P vehicle impacting their respective critical impact points at a speed of 62 mph (100 km/h) and an angle of 25 degrees. Test no. …

Opening Autonomous Airspace–A Prologue, Samuel M. Vance

International Journal of Aviation, Aeronautics, and Aerospace

The proliferation of Unmanned Aerial Vehicles (UAV), and in particular small Unmanned Aerial Systems (sUAS), has significant operational implications for the Air Traffic Control (ATC) system of the future. Integrating unmanned aircraft safely presents long-standing challenges, especially during the lengthy transition period when unmanned vehicles will be mixed with piloted vehicles. Integration of dissimilar systems is not an easy, straight-forward task and in this case is complicated by the difficulty to truly know what is present in the airspace. Additionally, there are significant technology, security and liability issues that will need resolution to ensure property and life are protected and …

Industrial-Grade Monitoring Solution: Hoistcam, Purdue Ect Team

ECT Fact Sheets Archive

Safety and productivity are top priorities for contractors and industrial operations. Improving either makes a company more profitable and competitive. Technology advancements that can do both are important for every company to consider. HoistCam^TM industrial-grade video monitoring solutions can improve employees’ productivity and workplace safety in the construction industries. HoistCam also improves efficiency of operations and reduces job site accidents resulting in substantial cost savings to a contractor.

HoistCam™ is an integrated, wireless video system. The use of HoistCam eliminates blind lifts, blind spots and can share the live video with anyone, anywhere with solid security and easy control. …

Ls-Dyna® Modeling Enhancement Support, John D. Reid, Robert W. Bielenberg, Chaz Ginger

Nebraska Department of Transportation: Research Reports

The Pooled Fund Program member states provided funding for LS-DYNA modeling enhancements in Years 17 thru 22 (2006-2011), with a project period of 2006-2016. This report documents many of the modeling issues addressed throughout the project period. The funding has been effectively utilized to advance the current state-of-the-art for computer simulation and has provided the following benefits for the entire industry: (1) improved roadside safety hardware, (2) reduced development time and cost, (3) improved understanding of the behavior of roadside safety features, especially for impacts outside of normal crash test conditions, (4) improved LS-DYNA modeling techniques and procedures, and (5) …

Using Lidar Data To Analyze Access Management Criteria In Utah, Marlee Lyn Seat

Theses and Dissertations

The Utah Department of Transportation (UDOT) has completed a Light Detection and Ranging (LiDAR) data inventory that includes access locations across the UDOT network. The new data are anticipated to be extremely useful in better defining safety and in completing a systemwide analysis of locations where safety could be improved, or where safety has been improved across the state. The Department of Civil and Environmental Engineering at Brigham Young University (BYU) has worked with the new data to perform a safety analysis of the state related to access management, particularly related to driveway spacing and raised medians. The primary objective …

Development Of Prognostic Techniques For Surface Defect Growth In Railroad Bearing Rolling Elements, Nancy De Los Santos, Robert Jones, Constantine Tarawneh, Arturo A. Fuentes, Anthony Villarreal

Mechanical Engineering Faculty Publications

Prevention of bearing failures which may lead to catastrophic derailment is a major safety concern for the railroad industry. Advances in bearing condition monitoring hold the promise of early detection of bearing defects, which will improve system reliability by permitting early replacement of failing components. However, to minimize disruption to operations while providing the maximum level of accident prevention that early detection affords, it will be necessary to understand the defect growth process and try to quantify the growth speed to permit economical, non-disruptive replacement of failing components rather than relying on immediate removal upon detection. The study presented here …