Engineering Commons^™

Effects Of Additive Manufacturing Methods On The Dynamic Properties Of 15-5ph Stainless Steel, Allison A. Dempsey

Theses and Dissertations

Experimental research was conducted to determine the dynamic properties and characterize the microstructure of 15-5PH Stainless Steel manufactured through Direct Metal Laser Sintering (DMLS) additive manufacturing (AM) processes and heat treated using common heat treatment protocols. A thorough understanding of the material's properties is necessary before such parts are utilized in an operational capacity. Of the five builds, two deviated significantly from the specified composition of 15-5PH stainless steel. The remaining three builds, possessing the desired composition and crystalline structure, were tested in compression and tension at two strain rates. Tension tests using a reflected wave and a momentum trap …

Determining The Degree Of The Routinization Of Additive Manufacturing In The Air Logistics Complexes, Candis A. Woods

Theses and Dissertations

Fiscal constraints have affected the USAF’s spending and sustainment of weapons systems that are being utilized beyond their programmed life cycle; therefore, it is imperative that processes be given the critical eye for improvement, innovative approaches, and/or best practice implementation. The AFSC, part of the AFMC, has embarked on a groundbreaking effort to transform operations and leverage industry best practices, while maintaining focus on warfighter support to create “The AFSC Way.” The AFSC Way is based on a shared leadership model that emphasizes speed, safety, and quality, which gives way to innovative ideas and new technologies in order to achieve …

Free And Open-Source Control Software For 3-D Motion And Processing, Bas Wijnen, G. C. Anzalone, Amberlee S. Haselhuhn, Paul G. Sanders, Joshua M. Pearce

Department of Materials Science and Engineering Publications

RepRap 3-D printers and their derivatives using conventional firmware are limited by: 1) requiring technical knowledge, 2) poor resilience with unreliable hardware, and 3) poor integration in complicated systems. In this paper, a new control system called Franklin, for CNC machines in general and 3-D printers specifically, is presented that enables web-based three dimensional control of additive, subtractive and analytical tools from any Internet connected device. Franklin can be set up and controlled entirely from a web interface; it uses a custom protocol which allows it to continue printing when the connection is temporarily lost, and allows communication with scripts.

3d Printed Microwave Hyperthermia Applicator, Umar Hasni, Christopher Deloglos, Patricia Moseh

Capstone Design Expo Posters

According to the CDC, every year approximately two million people are diagnosed with some type of cancer in the United States alone. Common procedures for cancer treatment include surgery, chemotherapy, and radiation therapy. Hyperthermia, an effective collateral treatment, is not included as part of regular cancer care. This is primarily due to its high cost.

Clinical studies for hyperthermia coupled with chemotherapy/radiation therapy have indicated up to a three-fold increase in survival rates of cancer patients. Unfortunately, current microwave hyperthermia systems are bulky, expensive and require special infrastructure in hospitals thus driving up the cost. The objective of this project …

Effects Of Defects On The Performance Of Hierarchical Honeycomb Metamaterials Realized Through Additive Manufacturing, Kazi Moshiur Rahman

Electronic Theses and Dissertations

Cellular metamaterials are of immense interest for many current engineering applications. Tailoring the structural organization of cellular structures leads to new metamaterials with superior properties providing lightweight and very strong/stiff structures. The incorporation of hierarchy to regular cellular structures enhances the properties and introduces novel tailorable metamaterials. For many complex cellular metamaterials, the only realistic manufacturing process is additive manufacturing (AM). The use of AM to manufacture large structures may lead to several types of defects during the manufacturing process, such as imperfect cell walls, irregular thickness, flawed joints, partially missing layers, and irregular elastic plastic behavior due to toolpath. …

Design Optimization Of Sandwich Core, Mohammad Tauhiduzzaman

Open Access Theses & Dissertations

Ultralight sandwich structures comprising of low-density core with stiff facings have attracted significant research interest for their considerable weight saving applications. The aircraft industries are focusing on decreasing the structural mass to lower the manufacturing and operating costs. Design analysis of the sandwich cores using finite element analysis has been developed as a promising concept to feature sandwich structures with maximum strength, stiffness, and reduced weight. To obtain multifunctional behavior of sandwich panels, a profound investigation of geometrical and mechanical properties in the transverse plane is required because it is very susceptible to any kind loadings. Structural optimization is one …

Effect Of Sparse-Build Internal Structure On Performance Of Fused Deposition Modeling Parts, Shixuan Meng

Masters Theses

"Fused deposition modeling (FDM) technology has been used in additive manufacturing for years and is able to significantly reduce both manufacturing time and cost for production tooling and end-use parts. Autoclave molding is one of the conventional tools used to produce composite parts. In autoclave molding, the soft composite material is positioned on the molding tool, and then subjected to vacuum and elevated temperatures to facilitate the curing of the resin. With additive manufacturing (AM), it is possible to fabricate the molding tool with a sparse internal structure, thereby reducing the fabrication time and cost compared to a solid tool. …

Thermophysical And Thermochemical Property Measurement And Prediction Of Liquid Metal Titanium Alloys With Applications In Additive Manufacturing, Jonathan Richard Raush

LSU Doctoral Dissertations

Accurate high-temperature thermophysical property data for liquid metals and alloys are important for simulation of laser-based 3D printing processes. To understand and better control such additive manufacturing processes, knowledge of density, viscosity, and surface tension of liquid metals and alloys versus composition and temperature is needed. Likewise, thermochemical property data information regarding alloys, including chemical activities and free energies relative to composition and temperature, aid in the understanding and development of phase data important in the material design process. Vacuum electrostatic levitation (ESL) is an important technique through which both thermophysical and thermochemical property measurements can be accomplished without physical …

Manufacturing And Mechanics Of Polymer Matrix Composites, Md Shariful Islam

Open Access Theses & Dissertations

Fiber-reinforced composite materials are widely used in the aerospace and automobile industries. Their strength-to-weight and stiffness-to-weight ratios make them suitable to be used in spacecraft, especially as cryogenic tank materials. One of the focus of this dissertation is to investigate the application of woven carbon and Kevlar® fiber composites as cryogenic tank materials. Tensile, bending and short beam shear tests are performed on rectangular specimens at room temperature and after cryogenic exposure (-196°C). It is found that the mechanical properties of these composite materials do not degrade significantly due to cryogenic exposure. It is observed that the failure mode took …

Hierarchical Control Of Complex Manufacturing Processes, Hesam Zomorodi Moghadam

Doctoral Dissertations

"The need for changing the control objective during the process has been reported in many systems in manufacturing, robotics, etc. However, not many works have been devoted to systematically investigating the proper strategies for these types of problems. In this dissertation, two approaches to such problems have been suggested for fast varying systems. The first approach, addresses problems where some of the objectives are statically related to the states of the systems. Hierarchical Optimal Control was proposed to simplify the nonlinearity caused by adding the statically related objectives into control problem. The proposed method was implemented for contour-position control of …

Additive Manufacturing Methodologies For Multi Process And Multi Material Scenarios, Tushar Saini

Mechanical and Aerospace Engineering Theses - Archive

Additive Manufacturing processes have been developing and continuously improving but are primarily constrained to single materials, albeit some commercial multi extrusion 3D printers do exist where by it is possible to print with multi-colored fluidic polymers or at most two filaments of the same type. 3D printing an object with volumetric varying properties requires manual modification of the G-Code, not a feasible option considering the average size of G-Code generated by the slicing software. This research focuses on developing a post processing methodology that modifies the large G-Code files generated by the slicing software according to user requirements. The proposed …

Integrated Voltage—Current Monitoring And Control Of Gas Metal Arc Weld Magnetic Ball-Jointed Open Source 3-D Printer, Yuenyong Nilsiam, Amberlee S. Haselhuhn, Bas Wijnen, Paul G. Sanders, Joshua M. Pearce

Department of Materials Science and Engineering Publications

To provide process optimization of metal fabricating self-replicating rapid prototyper (RepRap) 3-D printers requires a low-cost sensor and data logger system to measure current (I) and voltage (V) of the gas metal arc welders (GMAW). This paper builds on previous open-source hardware development to provide a real-time measurement of welder I-V where the measuring circuit is connected to two analog inputs of the Arduino that is used to control the 3-D printer itself. Franklin firmware accessed through a web interface that is used to control the printer allows storing the measured values and downloading those stored readings to the user’s …

Development And Prototype Validation Of An Additive Manufactured Cubesat Propulsion Tank, Geovanni A. Solorzano

Doctoral Dissertations and Master's Theses

The purpose of this study is to determine if a cubesat propellant tank using the additive manufacturing technology of direct metal laser sintering meets the requirements, and material properties of a conventionally manufactured tank. Additionally, to see if additive manufactured parts are a viable option to be used in cubesat applications. This was accomplished by designing a model which will be used by the ARAPAIMA cubesat that meets all the Air Force's University Nanosatellite Program (UNP), NASA's and Department of Defense's requirements for pressurized vessels and material properties. A finite element analysis study was conducted to determine where and when …

Characterizing Strain Accumulation, Residual Stress, And Microstructure Of Additive Manufactured Materials, Hannah K. Woods, Todd A. Book, Catalina Parada, Michael D. Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Additive Manufacturing (AM) is a rapidly evolving fabrication technology beneficial for its cost-saving potential to produce complex, low-volume shapes. However, AM materials are currently limited to nonstructural applications due to variability in their structural integrity, particularly their fatigue lives. IN718, Ti64, and Al10MgSi specimens manufactured by Direct Metal Laser Sintering (DMLS) were characterized based on variation of post-processing techniques and build direction. To understand the impact of each variable, surface roughness, hardness, residual stresses, microstructure, and strain accumulation in response to Low Cycle Fatigue (LCF) were studied. The use of Electron Backscatter Diffraction (EBSD) provided grain orientation and grain size …

Characterization Of Laser Deposited Ti-6al-4v To Nb Gradient Alloys, Clincy Cheung

Materials Engineering

An alloy was fabricated with Ti-6Al-4V and Nb powder using laser deposition (LD) to form a compositional gradient. The gradient was deposited, starting with Ti-6Al-4V powder, onto a forged Ti-6Al-4V substrate in an Argon environment. Niobium (Nb) composition increased by 4-at.% with each layer deposited until the composition reached 100-at.% Nb. This process yielded steep thermal gradients and affected the microstructure and mechanical properties across the compositional gradient. To observe the microstructural changes in the alloy, an etched gradient was viewed with optical microscopy at 1000x, where the grain structure was observed to be an acicular α phase at 100-at.% …

The Design For Manufacturing And Assembly Analysis And Redesign Of An Aircraft Refueling Door Hinge Utilizing Additive Manufacturing, Kurt A. Schwarz

Doctoral Dissertations and Master's Theses

In this thesis, an aircraft door hinge assembly provided by Gulfstream Aerospace was analyzed following an established process called DFMA. The hinge was then redesigned to be additively manufactured, which is uncommon currently in industry for load bearing components. It was shown that the Design for Manufacturing (DFM) guidelines were inadequate when applied to the new technology of additive manufacturing (AM). This was primarily due to AM's unique and unprecedented manufacturing capabilities.

A conservative redesign approach was followed due to a limitation in current AM material properties and time available for analysis. Despite this, a significant improvement in weight reduction …

Does Material Choice Drive Sustainability Of 3d Printing?, Jeremy Faludi, Zhongyin Hu, Shahd Alrashed, Christopher Braunholz, Suneesh Kaul, Leulekal Kassaye

Dartmouth Scholarship

Environmental impacts of six 3D printers using various materials were compared to determine if material choice drove sustainability, or if other factors such as machine type, machine size, or machine utilization dominate. Cradle-to-grave life-cycle assessments were performed, comparing a commercial-scale FDM machine printing in ABS plastic, a desktop FDM machine printing in ABS, a desktop FDM machine printing in PET and PLA plastics, a polyjet machine printing in its proprietary polymer, an SLA machine printing in its polymer, and an inkjet machine hacked to print in salt and dextrose. All scenarios were scored using ReCiPe Endpoint H methodology to combine …

Deposition Thickness Modeling And Parameter Identification For Spray Assisted Vacuum Filtration Process In Additive Manufacturing, August Mark

Electronic Theses and Dissertations

To enhance mechanical and/or electrical properties of composite materials used in additive manufacturing, nanoparticles are often time deposited to form nanocomposite layers. To customize the mechanical and/or electrical properties, the thickness of such nanocomposite layers must be precisely controlled. A thickness model of filter cakes created through a spray assisted vacuum filtration is presented in this paper, to enable the development of advanced thickness controllers. The mass transfer dynamics in the spray atomization and vacuum filtration are studied for the mass of solid particles and mass of water in differential areas, and then the thickness of a filter cake is …

Thermographic Investigation Of Laser Metal Deposition, Sreekar Karnati

Masters Theses

"Laser metal deposition as an additive manufacturing technique has been proven to possess the capability for fabricating complex, intricate geometries and excellent material properties through material deposition. Accurate manufacture of such geometric features would require precise control over the material deposition process. The need of the hour are process monitoring and analyses mechanisms that are crucial in ascertaining the occurrence of the intended actions during deposition while also serving as effective learning tools. The current work involved developing and incorporating an Infra-Red (IR) camera as a process monitoring tool for laser metal deposition. Using the IR camera the thermal dynamics …

An Experimental Study Of Fabrication Temperature Effect On Aqueous Extrusion Freeform Fabrication, Jie Li

Masters Theses

"In order to understand the effect of fabrication temperature, a computer controlled 3-D gantry system was used to extrude aqueous alumina paste using Extrusion Freeform Fabrication. The system includes a temperature control subsystem that allows for fabrication of components below the paste's freezing temperature in the range of -10⁰C to -30⁰C and a hot plate with temperature in the range of 20⁰C to 80⁰C inside a room temperature chamber. Comparisons in terms of relative density, mechanical properties, part accuracy and minimum deposition angle were performed by Extrusion Freeform Fabrication at 40⁰C plate temperature inside a room temperature chamber and at …

Stress-Limiting Test Structures For Rapid Low-Cost Strength And Stiffness Assessment, Andrew Katz, Craig P. Lusk, Nathan B. Crane

Faculty Publications

Purpose: Evaluate the use of a simple printed geometry to estimate mechanical properties (elastic modulus, yield strength) with inexpensive test equipment.

Design Methodology/Approach: Test geometry is presented that enables controlled strains with manual deformation and repeatable measurement of vibrational frequencies. This is tested with multiple FDM machines to assess measurement accuracy and repeatability. Printing orientation and some printing parameters are varied to assess the measurement sensitivity.

Findings: The test methods show good correlation with manufacturer material specifications in the X-Y plane and reported elastic strain limits. It is also sensitive to printing orientation and printing parameters.

Research Limitations/Implications: Further work …

Nanotechnology And Additive Manufacturing Platforms For Clinical Medicine: An Investigation Of 3d Printing Bioactive Constructs And Halloysite Nanotubes For Drug Delivery And Biomaterials, Jeffery A. Weisman

Doctoral Dissertations

Personalized medicine requires the development of new technologies for controlled or targeted drug delivery. Three-dimensional (3D) printing and additive manufacturing techniques can be used to generate customized constructs for bioactive compound delivery. Nanotechnology in the form of nanoparticles, used as a stand-alone construct or for material enhancements, can significantly improve established biomaterials such as PMMA based bone cements or enable new technology to have enhanced capabilities. Combinations of the technologies can be used in such applications as infectious disease treatments, chemotherapeutic targeted drug delivery or targeted delivery of nearly any bioactive compound.

Chemotherapeutic or antibiotic enhanced 3D printing filaments were …

Investigation Of Traditional And Alternate Living Hinge Designs For Fused Deposition Modeling Additive Manufacturing Process, Cassandra Sue Gribbins

Doctoral Dissertations and Master's Theses

A manuscript-style thesis composed of three studies covered the application of living hinge designs in the additive manufacturing process of fused deposition modeling. Initial research included comparing numerical and analytical linear analyses on a traditional living hinge design. The second research consisted of tensile testing for the material properties of the Acrylonitrile Butadiene Styrene (ABS) used in fused deposition modeling (FDM) process by the MakerBot 2X as well as adjusting the traditional design to be printed. The third study explored alternate living hinge designs that utilize the geometric freedom provided by additive manufacturing to more evenly distribute stress across the …

A Heuristic Algorithm For Determining The Part Set In A Powder-Bed Additive Manufacturing Machine., Sonja Dieder

Electronic Theses and Dissertations

The goal of this research is to develop a procedure for the placement of a priority part into a planned build in a powder-bed additive manufacturing machine. Toward that goal, a heuristic procedure was developed that seeks to maximize the revenue in a scheduled build, subject to due-date constraints; i.e., all parts with the closest due date will not only be included in the build, but will be placed near the bottom of the build. Likewise, any part in the scheduled build that does not have an immediate due date is a candidate for removal in order to accommodate a …

A Decision Support System To Measure Product Suitability For Additive Manufacturing Processes, Cynthia De Vasconcellos Barros

Theses and Dissertations - UTB/UTPA

Additive Manufacturing (AM) technologies started arising around 1980’s and they are currently considered to be the third industrial revolution. With improvements in computers, materials, and automated machines, manufacturers across several types of industries are becoming more familiar with AM processes, and it has become more common to see products that are being fabricated by using this new technology. However, there are still questions regarding when it is suitable to use Additive Manufacturing or conventional manufacturing processes depending on different factors. The purpose of this thesis is to create a Decision Support System (DSS) that will help users measure product suitability …

Characterization Of High-Purity Niobium Structures Fabricated Using The Electron Beam Melting Process, Cesar Adrian Terrazas

Open Access Theses & Dissertations

Additive Manufacturing (AM) refers to the varied set of technologies utilized for the fabrication of complex 3D components from digital data in a layer-by-layer fashion. The use of these technologies promises to revolutionize the manufacturing industry. The electron beam melting (EBM) process has been utilized for the fabrication of fully dense near-net-shape components from various metallic materials. This process, catalogued as a powder bed fusion technology, consists of the deposition of thin layers (50 - 120µm) of metallic powder particles which are fused by the use of a high energy electron beam and has been commercialized by Swedish company Arcam …

Master's In Electrical Engineering, Ricardo Xavier Rodriguez

Open Access Theses & Dissertations

This project is a focus on characterizing the process for actualizing three dimensional structures out of a carbon nanostructure composite via a direct print additive manufacturing process. Manufacturing parts additively enables for realization of geometrically complex shapes that often times cannot be manufactured any other way. The specificity of a material's properties have to be such, that the processing method can precisely place and bond material to itself in a highly repeatable manner. Commercial materials for additive manufacturing are have been optimized with these goals in mind and, therefore, often times lack the rigor and robustness for many applications.

The …

Fabrication Of A Nickel-Based Superalloy In Electron Beam Melting And Process Improvements Using Thermal Feedback From A Multi-Wavelength Pyrometer, Jonathan Minjares

Open Access Theses & Dissertations

The focus of this research was to fabricate parts composed of a nickel-based superalloy containing high levels of aluminum and titanium (NSAT) by using electron beam melting (EBM) additive manufacturing (AM) technology and utilizing thermal feedback from a multi-wavelength pyrometer to perform process improvements leading to near defect-free parts. EBM is an AM technology that utilizes metal powder to fabricate parts in layer-by-layer manner. A multi-wavelength pyrometer was implemented in an Arcam S12 (Arcam AB, Sweden) EBM system to observe and record surface temperatures throughout fabrication. Temperature data from the EBM system and the multi-wavelength pyrometer were graphed using MATLAB …

3d Printing For The Rapid Prototyping Of Structural Electronics, Rodolfo Salas

Open Access Theses & Dissertations

In business, the time required to shepherd a new product through the phases of concept, design, prototypes, through manufacture and finally making the product available for sale (together known as: Time to Market) is critical to the success and profitability of the next generation of products. The use of relatively new technologies, known as 3D Printing, which allow the fabrication of complex tridimensional shapes within hours of a completed CAD design without the need for tooling or molds, has significantly reduced the time required for a designer to physically hold a part designed only hours before and to perform form …

Comparative Characterization Of Ni-Base Superalloys Fabricated By Laser And Electron Beam Melting Technologies, Krista Amato

Open Access Theses & Dissertations

Nickel-base superalloys have been used in cast and wrought, and powder metallurgy forms for nearly four decades for industrial and automotive applications. One drawback of cast alloys is that upon solidification, there is minimal microstructural control. Another issue to be improved is to eliminate the limitations of shapes and forms of fabricated alloys.

Rapid prototyping is a new technology of additive manufacturing that shows to be promising for the freeform fabrication of novel superalloys, including nickel-base alloys. New rapid manufacturing technologies allow us to produce parts in any shape that can be designed by computer-aided design (CAD) software. Additionally, the …