Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Publication
- Publication Type
Articles 1 - 8 of 8
Full-Text Articles in Engineering
Optimized Tip Cooling Using Am Process, Alberto H. Gamez, Lourdes Sarmiento Martinez, Andrew Van Bogelen
Optimized Tip Cooling Using Am Process, Alberto H. Gamez, Lourdes Sarmiento Martinez, Andrew Van Bogelen
Mechanical Engineering
This Final Design Review (FDR) reports on the senior design project undertaken by our team of mechanical engineering seniors at California Polytechnic State University, San Luis Obispo. This project seeks to use the additive manufacturing process to improve the existing design of a Taurus 60 gas turbine injector tip. The current injector tip is owned by Solar Turbines, a designer and manufacturer of gas turbines for electric generation, propulsion, as well as natural resource transportation. The challenge at hand is to design a new injector tip that will be reliable for at least 60,000 hours and provide ease of replacement, …
Wind Blade Manufacturing For The Cal Poly Wind Power Club, Benjamin E. Thompson, Jake R. Lund, Claudia C. Angeles
Wind Blade Manufacturing For The Cal Poly Wind Power Club, Benjamin E. Thompson, Jake R. Lund, Claudia C. Angeles
Mechanical Engineering
The Cal Poly Wind Power Club is entering the 2021 Collegiate Wind Competition (CWC) in June. Last year, three senior project teams were assigned to collaborate and assist the club with the pitching mechanism, the rotor balancing, and the manufacturing process. As the manufacturing team, the goal of our project was to design a manufacturing process for the bladegeometry given. The manufacturing process was required to meet the team’s expectations and CWC’s performance requirements to place highly in the competition taking place in June 2021.These expectations included creating a manufacturing process that is repeatable and reliable for future competitions. The …
Effects Of Powder Recycling In Selective Laser Melting, Nina L. Menon
Effects Of Powder Recycling In Selective Laser Melting, Nina L. Menon
Industrial and Manufacturing Engineering
The following report analyzes 316L stainless steel powder characteristics of new powder and powder that has been used in the selective laser melting process for 40-50 builds. A literature review was done of powder characteristics, different ways flowability can be tested, and effects of recycling other types of metal powders in Additive Manufacturing. Flowability improved over 21 reuses of the titanium alloy Ti-6Al-4V and resulted in stronger printed parts. Flow of S17-4 PH steel powder was measured with a Hall flowmeter and increased significantly over the course of 10 reuses. Heavily recycled (estimated 50 reuses) 316L SS powder and brand …
Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom
Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom
Mechanical Engineering
This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …
Evaluation Of Tensile Properties For Selective Laser Melted 316l Stainless Steel And The Influence Of Inherent Process Features, Paul Swartz
Master's Theses
Optimal print parameters for additively manufacturing 316L stainless steel using selective laser melting (SLM) at Cal Poly had previously been identified. In order to further support the viability of the current settings, tensile material characteristics were needed. Furthermore, reliable performance of the as-printed material had to be demonstrated. Any influence on the static performance of parts in the as-printed condition inherent to the SLM manufacturing process itself needed to be identified. Tensile testing was conducted to determine the properties of material in the as-printed condition. So as to have confidence in the experimental results, other investigations were also conducted to …
Additive Manufacturing Powder Removal, Madison A. Lignell, Tyler W. Laird, Kurt K. Reed
Additive Manufacturing Powder Removal, Madison A. Lignell, Tyler W. Laird, Kurt K. Reed
Mechanical Engineering
Metal powder-bed fusion is an additive manufacturing process which enables the creation of unique shapes in metal parts that would otherwise be difficult, expensive, or impossible to machine. Metallic powder is melted and fused together by either a laser or electron beam to produce parts quickly. The excess powder covers newly printed parts and can be difficult to remove from small internal features. The scope of this project is to design a device that effectively removes the powder from newly printed parts safely, while reclaiming as much powder as possible for reuse. The solution for this project must be able …
Characterization Of Laser Deposited Ti-6al-4v To Nb Gradient Alloys, Clincy Cheung
Characterization Of Laser Deposited Ti-6al-4v To Nb Gradient Alloys, Clincy Cheung
Materials Engineering
An alloy was fabricated with Ti-6Al-4V and Nb powder using laser deposition (LD) to form a compositional gradient. The gradient was deposited, starting with Ti-6Al-4V powder, onto a forged Ti-6Al-4V substrate in an Argon environment. Niobium (Nb) composition increased by 4-at.% with each layer deposited until the composition reached 100-at.% Nb. This process yielded steep thermal gradients and affected the microstructure and mechanical properties across the compositional gradient. To observe the microstructural changes in the alloy, an etched gradient was viewed with optical microscopy at 1000x, where the grain structure was observed to be an acicular α phase at 100-at.% …
Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd
Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd
STAR Program Research Presentations
Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …