Engineering Commons^™

Advanced Intermediate Manufacturing (Aim) Supply Chain Concepts Leading To Reduced Lead Times And Improved Responsiveness, Eric S. Draudt

Theses and Dissertations

This thesis investigates the optimization of the supply chain for key aircraft components, focusing on the implementation of Advanced Intermediate Manufacturing (AIM) production facilities. Utilizing anyLogistix, the study compares the current supply chain model based on Supply Chain Operations Wing (SCOW) data with various AIM production facility configurations: single, dual, quadruple, and three utilization-driven models (high, medium, and low). The findings demonstrate that integrating AIM production facilities significantly reduces lead times, with even a single facility dramatically cutting down the lead time from over 800 days to approximately 104 days. The utilization models further provide insights into operational flexibility under …

Heat Treatments For Minimization Of Residual Stresses And Maximization Of Tensile Strengths Of Scalmalloy® Processed Via Directed Energy Deposition, Rachel Boillat-Newport, Sriram Praneeth Isanaka, Jonathan Kelley, Frank Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Scalmalloy® is an Al-Mg-Sc-Zr-Based Alloy Specifically Developed for Additive Manufacturing (AM). This Alloy is Designed for Use with a Direct Aging Treatment, as Recommended by the Manufacturer, Rather Than with a Multistep Treatment, as Often Seen in Conventional Manufacturing. Most Work with Scalmalloy® is Conducted using Powder Bed Rather Than Powder-Fed Processes. This Investigation Seeks to Fill This Knowledge Gap and Expand Beyond Single-Step Aging to Promote an overall Balanced AM-Fabricated Component. for This Study, Directed Energy Deposition (DED)-Fabricated Scalmalloy® Components Were Subjected to Low-Temperature Treatments to Minimize Residual Stresses Inherent in the Material Due to the Layer-By-Layer Build Process. …

Residual Stress Generation In Additive Manufacturing Of Complex Lattice Geometries, Katie Bruggeman, Nathan Klingbeil, Anthony N. Palazotto

Faculty Publications

Residual stresses developed during additive manufacturing (AM) can influence the mechanical performance of structural components in their intended applications. In this study, thermomechanical residual stress simulations of the laser powder bed fusion (LPBF) process are conducted for both simplified (plate and cube-shaped) geometries as well as five complex lattice geometries fabricated with Inconel 718. These simulations are conducted with the commercial software package Simufact Additive©, which uses a nonlinear finite element analysis and layer-by-layer averaging approach in determining residual stresses. To verify the efficacy of the Simufact Additive© simulations, numerical results for the plate and cube-shape geometries are analyzed for …

A Review On Additive Manufacturing For Aerospace Application, Radhika C, Ragavanantham Shanmugam, Monsuru Ramoni, Gnanavel Bk

Manufacturing & Industrial Engineering Faculty Publications

Additive manufacturing, a cutting-edge technology often colloquially known as 3D printing, is a transformative process used to meticulously fabricate complex components by adding material layer upon layer. This revolutionary manufacturing method allows for precise control and customization, making it a go-to choice in various industries, from aerospace to healthcare. The adroitness of additive manufacturing in creating a complex geometry as a whole is very much harnessed by the aerospace Industry. Generating a component using additive manufacturing involves optimal design, methods, and processes. This review gives a broad knowledge in developing a part or product by choosing the appropriate design, method, …

Editorial: Frontiers In Lasers And Applications, John T. Fourkas, Koji Sugioka, Yongfeng Lu

Department of Electrical and Computer Engineering: Faculty Publications

When the laser was invented in 1960 by Theodore H.Maiman, the potential applications of this apparatus were far from clear. Indeed, even 4 years later, Maiman himself, in an interview with The New York Times, called the laser “a solution seeking a problem.”

Nearly 64 years later, it is safe to say that the laser’s influence on our everyday lives has been nearly beyond measure. Lasers are integral to CD and DVD readers, barcode readers, many computer printers, speed and distance sensors, and in various entertainment systems used in concerts and other events.

Pcl And Dmso2 Composites As Biomaterials For Additive Manufacturing, Jae-Won Jang

Dissertations and Theses

Tissue engineering provides a viable solution to address the shortage of organ donors for allograft transplants. Its primary objective is the replacement or regeneration of damaged tissues which is developed by combining living cells, a scaffold, and a bioreactor. Among these components, the scaffold serves as an artificial extracellular matrix (ECM), which plays a pivotal role in supporting cell adhesion, proliferation, differentiation, and overall tissue development. Additive manufacturing (AM), commonly referred to as three-dimensional (3D) printing, emerges as a promising method for scaffold fabrication due to its capability to create complex and repeatable geometries.

Polycaprolactone (PCL) has been one of …

Experimental Investigations And Optimization Of 3d Printed Cellular Structures For Protection Against Traumatic Brain Injury, Aaron R. Jackson

Mechanical and Aerospace Engineering Dissertations - Archive

Traumatic Brain Injury (TBI) disrupts brain function due to head impacts, blast exposures, and ballistic penetrations. It is a significant cause of mental health issues and disability, particularly among military personnel. Historically, combat helmets were designed primarily to protect against fragments. However, recent data highlights the need for helmets that also protect against blast and blunt impacts. Effective TBI prevention requires helmets that address various energy threats while remaining lightweight. A critical metric in this effort is head acceleration, which is closely linked to injury across different scales of brain damage.

Four lattice structures were 3D printed using Digital ABS …

Thermal Damage And Mechanical Failure Analysis Of Polymers, Tina Ko

Mechanical and Aerospace Engineering Theses - Archive

As the demand for more intricate and precise components increases, polymers continue to stand out for their flexibility, durability, and adaptability across numerous applications. From aerospace to biomedical engineering industries, polymers are valued for their versatility and customizability, enabling the creation of complex geometries or achieving specific material properties. Since polymers are widely used, analyzing their thermal and mechanical properties is essential to understand their behavior under high-energy exposure or defects. Two types of polymers were analyzed: Polydimethylsiloxane (PDMS) and 3D-printed digital materials. This thesis investigates the mechanical and thermal response of polymers through two distinct studies. The first part …

Sustainable Additive Manufacturing Of Polysulfone Membranes For Liquid Separations, Brian Leonard, Harrison Loh, David Lu, Ebuka A. Ogbuoji, Isabel Escobar, Konstantinos Sierros, Oishi Sanyal

UK CARES Faculty Publications

Membranes serve as important components for modern manufacturing and purification processes but are conventionally associated with excessive solvent usage. Here, for the first time, a procedure for fabricating large area polysulfone membranes is demonstrated via the combination of direct ink writing (DIW) with non-solvent induced phase inversion (NIPS). The superior control and precision of this process allows for complete utilization of the polymer dope solution during membrane fabrication, thus enabling a significant reduction in material usage. Compared to doctor blade fabrication, a 63% reduction in dope solution volume was achieved using the DIW technique for fabricating similarly sized membranes. Cross …

Additive Manufacturing Of Novel Lightweight Insulation Refractory With Hierarchical Pore Structures By Direct Ink Writing, Saisai Li, Jiaxuan Xin, Ruoyu Chen, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

A direct ink writing process using fly ash foaming slurries was employed for the additive manufacturing of lightweight mullite insulation refractory with hierarchical pore structures. The viscosity, thixotropy, and shear thinning behavior of the inks were analyzed to investigate the effect of the inorganic binder and dispersant of the foaming inks. A slurry exhibiting excellent rheological characteristics was identified, consisting of 45 wt% fly ash floating beads, 55 wt% water, 3.0 wt% additional dispersant, and 6.0 wt% additional binder. Furthermore, through the optimization of printing parameters such as printing pressure and printing speed, notable enhancements were achieved in the pore …

Phenolic Polymer Infiltration And Pyrolysis Process For Additively Manufactured Carbon/Peek Composites To Produce Carbon–Carbon Composites, S. Weiler, H. A. Haffner, K. Chandrashekhara, J. Watts, G. E. Hilmas, J. Bayldon, L. M. Rueschhoff

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Carbon–carbon composites are carbon fibers reinforced with carbon matrix and are classified as advanced materials well suited for high-temperature structural applications. Carbon–carbon composites are characterized by maintaining excellent mechanical properties and structural stability at high temperatures and have been used in aerospace application as nozzles, heatshields, and leading edge. However, conventional methods to manufacture carbon–carbon composites are costly and time-consuming. the aim of this work is to develop a method for creating additively manufactured (AM) carbon–carbon composites using a high-pressure re-infiltration process. in doing so, less infiltration cycles are required compared to a low-pressure re-infiltration, reducing the total manufacture time. …

Production Of Glass-To-Metal Seals Using Additive Manufacturing Techniques, Aaron Read

Masters Theses

"Glass-to-metal (GtM) seals are hermetic barriers between glass and metal components, often used in the electronic and vacuum industries. Creating the seals traditionally requires heating all the components to the glass melting temperature, where the glass will flow and bond to the metal. Due to the manufacturing constraints of the individual components and sealing conditions there are geometric and material restrictions. Additive manufacturing techniques were used to make GtM seals to reduce these restrictions.

Hermetic, single pin seals were produced using printed metal shells, by selective laser melting (SLM), and digital light processing (DLP) printed glass preforms. Glass preforms were …

Development Of A Highly Loaded Zirconium Carbide Paste For Material Extrusion Additive Manufacturing, Clare Sabata, Austin J. Martin, Jeremy L. Watts, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

A highly loaded, aqueous-based zirconium carbide (ZrC) paste was developed for ceramic on-demand extrusion (CODE). Commercial ZrC powder was ball milled to reduce the particle size to ∼1 μm. Paste composition was determined by rheological characterization and observation of printing behavior; the final paste consisted of 46–47 vol% ZrC, 43.5 vol% distilled water, 8.1 vol% dispersant, and 1.6 vol% binder. Rheological characterization of the paste showed a yield stress of ∼8 Pa and shear thinning behavior (ΔG′/Δσ* = −55). The paste was printed using a 610 μm nozzle; a test print showed shape fidelity using the developed paste. A pressureless …

Development Of Advanced Multi-Nozzle Multi-Material 3d Printing, Mohammed Al Ali

Wayne State University Dissertations

Extrusion-based 3D printing methods, such as Direct Ink Writing, are extensively utilized across sectors like biomedical, energy, and electronics, employing a diverse range of materials. However, the lengthy printing times associated with single-nozzle systems limit their application in complex mass production and rapid prototyping. While multi-nozzle systems have attempted to address this issue, they often result in costly, and bulky setups with limited material options. This research introduces a novel multi-nozzle multi-material system that allows for simultaneous 3D printing using bent nozzles. The system is cost-effective, simple in design, and capable of printing a wide range of materials. Its universal …

Advancements And Challenges In Additively Manufactured Functionally Graded Materials: A Comprehensive Review, Suhas Alkunte, Ismail Fidan, Vivekanand Naikwadi, Shamil Gudavasov, Mohammad Alshaikh Ali, Mushfig Mahmudov, Seymur Hasanov, Muralimohan Cheepu

Engineering Technology Faculty Publications

This paper thoroughly examines the advancements and challenges in the field of additively manufactured Functionally Graded Materials (FGMs). It delves into conceptual approaches for FGM design, various manufacturing techniques, and the materials employed in their fabrication using additive manufacturing (AM) technologies. This paper explores the applications of FGMs in diverse fields, including structural engineering, automotive, biomedical engineering, soft robotics, electronics, 4D printing, and metamaterials. Critical issues and challenges associated with FGMs are meticulously analyzed, addressing concerns related to production and performance. Moreover, this paper forecasts future trends in FGM development, highlighting potential impacts on diverse industries. The concluding section summarizes …

Energy Efficiency In Additive Manufacturing: Condensed Review, Ismail Fidan, Vivekanand Naikwadi, Suhas Alkunte, Roshan Mishra, Khalid Tantawi

Engineering Technology Faculty Publications

Today, it is significant that the use of additive manufacturing (AM) has growing in almost every aspect of the daily life. A high number of sectors are adapting and implementing this revolutionary production technology in their domain to increase production volumes, reduce the cost of production, fabricate light weight and complex parts in a short period of time, and respond to the manufacturing needs of customers. It is clear that the AM technologies consume energy to complete the production tasks of each part. Therefore, it is imperative to know the impact of energy efficiency in order to economically and properly …

Laser Deposition Additive Manufacturing Of Multi-Material And Metal-Ceramic Composite Structures, Manikanta Grandhi

Graduate Theses, Dissertations, and Problem Reports (ETD)

The increasing performance requirements of modern industrial systems, coupled with the imperative for decarbonization, necessitate a fundamental rethinking of metallic component design and manufacturing. Traditional materials, with their inherent limitations in property optimization, susceptibility to degradation, and weight constraints, are proving insufficient. Multi-material joining offers a potential solution, enabling designers to strategically integrate diverse materials with specific, tailored properties into single component. Functionally graded materials (FGMs) and oxide dispersion strengthened (ODS) materials are prime examples of this approach, delivering substantial improvements in wear resistance, thermal regulation, high-temperature resilience, and overall weight efficiency. However, conventional manufacturing approaches further exacerbate the limitations …

Integration Of Infrared Thermography And Deep Learning For Real-Time In-Situ Defect Detection And Rapid Elimination Of Defect Propagation In Material Extrusion, Asef Ishraq Sadaf

College of Graduate Studies: Theses & Dissertations

This study presents a novel approach to overcoming process reliability challenges in Material Extrusion (ME), a prominent additive manufacturing (AM) technique. Despite ME's advantages in cost, versatility, and rapid prototyping, it faces significant barriers to commercial-scale production, primarily due to quality issues such as overextrusion and underextrusion, which compromise final part performance. Traditional manual monitoring methods severely lack the capability to efficiently detect these defects and highlight the necessity for an efficient and real-time monitoring solution. Considering these challenges, an innovative and field-deployable infrared thermography-based in-situ real-time defect detection and feedback control system is proposed in this thesis. A novel …

Investigating The Role Of Tesserae In Energy Absorption In Shark Cartilage, Molly Dobrow

UNF Graduate Theses and Dissertations

Unlike mammals, shark endoskeletons are composed of cartilage, which is less stiff compared to bone. Despite this structural disadvantage, sharks have risen to become apex predators, with reported maximum posterior bite force estimates approximating 5914 N in bull sharks. Shark jaws are estimated to undergo high cycle loading within the organism’s lifecycle without evidence of failure. Fatigue resistance may relate to mineral distribution within a component of the endoskeletal system – tesserae. Tesserae are thin, roughly hexagonal tiles composed of calcium phosphate hydroxyapatite (HA) crystals and grow by accretion to eventually surround the hyaline cartilage core. Though tesserae dimensions are …

Towards The Automation Of Post-Processing Of Additive Manufacturing Using Collaborative Robots, Logan Schorr

Theses and Dissertations

Despite the incredible potential that collaborative robots have, they are underutilized in several industries that could benefit greatly. These specialized fields, such as additive manufacturing, face challenges that can be solved with the use of robotics, including advanced computer vision, end-effector tooling, and process refinement. My research aims to utilize collaborative robots in an effort to solve the above stated problems, for the specific fields of additive manufacturing. Specifically within this field is the automation of post-processing; this is normally completely manual, as the tools for automation are not sufficiently developed to handle the flexibility required for additive manufacturing. This …

An Investigation Into Applications Of Canonical Polyadic Decomposition & Ensemble Learning In Forecasting Thermal Data Streams In Direct Laser Deposition Processes, Jonathan Storey

Theses and Dissertations

Additive manufacturing (AM) is a process of creating objects from 3D model data by adding layers of material. AM technologies present several advantages compared to traditional manufacturing technologies, such as producing less material waste and being capable of producing parts with greater geometric complexity. However, deficiencies in the printing process due to high process uncertainty can affect the microstructural properties of a fabricated part leading to defects. In metal AM, previous studies have linked defects in parts with melt pool temperature fluctuations, with the size of the melt pool and the scan pattern being key factors associated with part defects. …

A Human Factors Approach To Improve Layout Design For A Virtual Reality-Based Training Platform, Md Humaun Kobir, Taufiq Rahman, Yiran Yang, Shuchisnigdha Deb

SAGE Open Access Agreement Publications-Archive

In manufacturing industries, equipment arrangement, and layout design are critical factors that directly influence productivity, workplace safety, and workers’ performance. Link analysis, as a human factors approach, has been widely used in industries for many years to improve layout design and machinery arrangement. This approach considers humans' physical and cognitive capabilities and movement limitations to find an optimal design. Virtual reality significantly impacts our society from product design to worker training. Hence, effective virtual training platforms require the same attention to layout design as manufacturing work settings which offer efficient testing of multiple layouts. This research focuses on developing a …

Additive Manufacturing Of Composites For Sensing And Harsh Environments Application, Md Sahid Hassan

Open Access Theses & Dissertations

Composite materials are made by combining two or more materials, such as fibers and resins to create a material system that has improved mechanical and physical properties compared to its individual components. The use of 3D printing technology in composite manufacturing allows for the creation of complex and custom shapes with precise control over the placement of the materials. This makes it possible to create composite parts with enhanced performance characteristics and reduced weight. The work presented in this dissertation lies in the design and development of highly flexible impact propagation sensor through material extrusion 3D printing technique. By using …

Advancing Additive Manufacturing For Biomedical Applications: Antimicrobial And X-Ray Absorptive Composite Filaments For Fused Filament Fabrication, John M. Arnold Jr

LSU New Orleans Theses and Dissertations

The objective of this research was to investigate the use of nano- and microparticle amendments for the creation of Poly-lactic Acid composite materials for use in biomedical applications using the Fused Filament Fabrication process of Additive Manufacturing. Composites were created with the goal of imparting the useful properties of antimicrobial activity and x-ray absorption to the material. In addition to testing the efficacy of the particle amendments in achieving the desired properties, the thermal and mechanical properties of the composite materials were tested to ensure that the composites would be compatible with the Fused Filament Fabrication process and would produce …

Additively Manufactured Cryogenic Engineered Heat Pipe For Lunar Ice Collection, Mahadi Hasan

Open Access Theses & Dissertations

Nowadays, one of the most talked-about subjects in space exploration is cryogenic heat pipes. These heat pipes are made in a way that allows them to operate without the need for additional power or energy. Evaporated vapor and condensed liquid can be moved by buoyancy forces or capillary forces that are subject to gravity because of the phase shifts of the working fluids moving inside. The cooling solution typically entails a phase transition from liquid to vapor, which can dissipate larger heat fluxes because of the fluid's high latent heat of vaporization. Recent developments in additive manufacturing and micro-nano structures …

Ultrasonic Non-Destructive Evaluation Of Additively Manufactured Polymer-Ceramic Composites, Christian Alexander Ruiz

Open Access Theses & Dissertations

Digital light processing (DLP) is an attractive additive manufacturing technique due to its ability to create ceramic parts with complex geometries. DLP uses ultraviolet light to polymerize a slurry comprised of ceramic powder and photosensitive resin in layers to create solid parts. Printing parameters such as light intensity and exposure time are critical when producing these parts. Improper parameters can lead to over or under-curing, adversely impacting print quality and strength. Samples were printed at varying layer exposure times and then tested using ultrasonics to determine the degree of conversion. Additionally, ultrasonics were used as a non-destructive technique to obtain …

Upcyclying Of Polyethylene Terephtalate By Addition Of Thermoplastic Elastomer, Diego Francisco Bermudez

Open Access Theses & Dissertations

Continual overconsumption of single-use plastics has generated challenges of solid waste management across the United States. Common plastic waste management solutions, such as landfill, have caused the migration of contaminants into the environment consequently affecting not only the health of wildlife, but also that of human beings. Alternative strategies for the handling of single-use plastic such as polyethylene terephthalate (PET), used in the food packaging industry, can ultimately help mitigate the noxious consequences of single-use plastics affecting entire ecosystems. This study demonstrates a potential avenue of materials upcycling by studying the effects of coupling PET with the thermoplastic elastomer styrene-ethylene-butylene-styrene …

Design, Fabrication, And Integration Of Robotic Skin Sensors For Human Robot Interaction., Olalekan Olakitan Olowo

Electronic Theses and Dissertations

Enhancing physical human-robot interaction in modern robotics relies on refining the tactile perception of robot skin sensors. This research focuses on crucial aspects of the development process, including fabrication techniques, miniaturization, and integration for a more efficient collaborative human-robot interface. The fabrication process of robot skin sensors, designed to mimic human skin, is explored both within and outside cleanroom environments. An enhanced technique is presented to increase fabrication yield and create more miniaturized sensor designs with feature sizes in the tens of microns. These sensors function as piezoresistive arrays using organic polymers like PEDOT: PSS as the pressure-sensing medium. Various …

Additive Manufacturing Of Microelectronic Devices For Extreme Environments, Nicholas Mckibben

Boise State University Theses and Dissertations

This work encompasses a comprehensive exploration of advanced manufacturing techniques for fabricating microelectronic devices compatible with extreme environments. The research integrates the fields of chemistry, nanomaterials, and additive manufacturing to achieve remarkable progress in sensor development, with a particular emphasis on aerosol jet printing (AJP), surface acoustic wave (SAW) devices, patterned graphene growth, and surface functionalization. The investigation begins with the AJP process development of a commercial silver nanoparticle ink, culminating in the fabrication of a piezoelectric SAW transducer that was prototyped as a high-temperature thermometer, showing excellent linearity when validated to 200°C. Next, the investigation continued with the development …

Damage Detection With An Integrated Smart Composite Using A Magnetostriction-Based Nondestructive Evaluation Method: Integrating Machine Learning For Prediction, Christopher Nelon

All Dissertations

The development of composite materials for structural components necessitates methods for evaluating and characterizing their damage states after encountering loading conditions. Laminates fabricated from carbon fiber reinforced polymers (CFRPs) are lightweight alternatives to metallic plates; thus, their usage has increased in performance industries such as aerospace and automotive. Additive manufacturing (AM) has experienced a similar growth as composite material inclusion because of its advantages over traditional manufacturing methods. Fabrication with composite laminates and additive manufacturing, specifically fused filament fabrication (fused deposition modeling), requires material to be placed layer-by-layer. If adjacent plies/layers lose adhesion during fabrication or operational usage, the strength …