Engineering Commons^™

Studying The Compressive, Tensile And Flexural Properties Of Binary And Ternary Fiber-Reinforced Uhpc Using Experimental, Numerical And Multi-Target Digital Image Correlation Methods, Behrooz Dadmand, Hamed Sadaghian, Sahand Khalilzadehtabrizi, Masoud Pourbaba, Milad Shirdel, Amir Mirmiran

Civil Engineering Faculty Publications and Presentations

Compressive, tensile, and flexural properties of ultra-high-performance concrete (UHPFRC) specimens were studied in this research. Binary and ternary combinations of micro steel (MS), round crimped (RC), crimped (C), hooked-end (H), and polypropylene (PP) fibers were used in overall ratios of 2% by volume of concrete. For this purpose, 100 x 200 mm cylindrical specimens, dog-bone specimens (length: 330 mm, width: 80 mm, thickness: 40 mm), and prismatic beams with a dimension of 100 x 100 x 500 mm (clear span: 450 mm) were cast and tested under compressive, tensile, and four-point bending tests (4PBT). A digital image correlation (DIC)-based method …

Real Depth-Correction In Ground Penetrating Radar Data Analysis For Bridge Deck Evaluation, Sepehr Pashoutani, Jinying Zhu

Department of Civil and Environmental Engineering: Faculty Publications

When ground penetrating radar (GPR) is used for the non-destructive evaluation of concrete bridge decks, the rebar reflection amplitudes should be corrected for rebar depths to account for the geometric spreading and material attenuation of the electromagnetic wave in concrete. Most current depth-correction methods assume a constant EM wave velocity in the entire bridge deck and correct GPR amplitudes based on the two-way travel time (TWTT) instead of the actual rebar depth. In this paper, we proposed a depth-correction algorithm based on the real rebar depths. To compare different depth-correction methods, we used gprMax software to simulate GPR signals in …

The Effect Of Graphite And Activated Carbon As Dispersed Particle In Base Fluid As Quench Medium On The Hardness Of S45c Carbon Steel, Wahyuaji Narottama Putra, Danika Aprilia Somadinata, Ghiska Ramahdita

Journal of Materials Exploration and Findings

Adding a solid particle dispersion into a base fluid could increase its thermal conductivity, hence increasing the heat transfer characteristics. One example of this thermally enhanced fluid is in heat treatment industry as quench medium. By controlling the amount of the dispersed particle, the cooling rate of the quench medium can be altered, and could affect steel hardness after heat treatment. In this research, the dispersed particle used was commercially available graphite and activated carbon particle. As for the base fluid, distilled water and common engine oil were compared. The concentration of the dispersed particle was 0.1, 0.3, 0.5 weight …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Structural Integrity Analysis Of The Rig Mast Following Repair Of Two Diagonal Braces In The Upper Mast Section, Rendhatya Padmodwiputra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Bambang Eka Satria, Chandra Arif, Eka Juni Suarthana

Journal of Materials Exploration and Findings

During a move to the new drilling location, two braces of the upper mast section on a 550 HP oil and gas rig was damaged. When damage is discovered, the rig operating company should conduct a risk analysis related to the damage using the standard used to determine rejection criteria and follow-up repairs. The strength of the rig mast is calculated using Finite Element Analysis (FEA) with initial conditions (before damage occurs) where all braces are installed and extreme conditions where neither brace is repaired. The calculation results are then used to assess the risk of reducing the rig mast …

Development Of Battery Materials To Function As Corrosion Protection On Car Body Plates, Tubagus Noor Rohmannudin, Sulistijono Sulistijono, Noval Adrinanda, Faridz Wira Dharma, Samuel Areliano

Journal of Materials Exploration and Findings

Most car bodies made for mass production are made from steel or aluminum. Both are strong metals, but steel is cheaper than aluminum and is more commonly used in lower-end cars for a broader consumer range. The weakness of steel compared to aluminum is that it is susceptible to corrosion under certain conditions, and thus it may deteriorate over time without proper care. To prevent corrosion, modern cars are coated with paint to prevent direct contact with the environment. As a second line of protection, a car battery can be connected to the body to create an impressed current cathodic …

Effect Of Austenization And Repeated Quenching On The Microstructures And Mechanical Properties Of Wear-Resistant Steel, Yanuar Nugraha, Myrna Ariati Mochtar

Journal of Materials Exploration and Findings

This study was focused on determining the effect of repeated austenitization and quenching on mechanical properties and microstructure. The experiment was carried out in a rolled quencher facility with a heat treatment process of one to two times, with parameters of an austenizing temperature of 9500C and quenching at a temperature of 8500C with pressurized water media. Testing of specimens, including microstructure observations and hardness testing. The repeated heat treatment process showed an increase in hardness of 0.79% on one-time repeated heat treatment and 1.65% on two repeated heat treatments. This occurs due to the presence accompanied by refinement of …

Potential Of Biduri Fiber (Calotropis Gigantea) As Material For Oil Spill Absorbent, Anne Sukmawati, Wulan Septiani

Journal of Materials Exploration and Findings

Biduri fiber (Calotropis gigantea) is a natural hollow fiber with hydrophobic and oleophilic properties potentially used as oil spilled sorbent from seawater. This study aims to determine the absorption capacity and efficiency of the Biduri fiber and membrane to fuel oil. Measurement of oil absorption to seawater was carried out at various fiber weights (0.5-1.5 g), fiber composition (50-95%), contact time (10-90 minutes), temperature (30 and 50°C), and compared with commercial products. The results showed that the fiber weight variation of 0.5-1.5 g has an average absorption efficiency of 96.67%, and the highest absorption was obtained in a weight of …

Numerical Study Of Owls’ Leading-Edge Serrations, Asif Shahriar Nafi

Electronic Theses and Dissertations

The silent flight ability of owls is often attributed to their unique wing morphology and its interaction with their wingbeat kinematics. Among these distinctive morphological features, leading-edge serrations stand out – these are rigid, miniature, hook-like patterns located at the leading edge of the primary feathers of their wings. It had been hypothesized that these leading-edge serrations serve as a passive flow control mechanism, influencing the aerodynamic performance and potentially affecting the boundary layer development over the wing, subsequently influencing wake flow dynamics. Despite being the subject of research spanning multiple decades, a consensus regarding the aerodynamic mechanisms underpinning owls’ …

The Effects Of Phosphorus Pentoxide Additions On The Thermal, Rheological, And Structural Properties Of Sodium Borosilicate Glass, K. L. Skerratt-Love, J. L. George, A. M.T. Bell, F. Sweeney, D. Cutforth, C. (Charmayne) E. Lonergan, D. R. Dixon, A. A. Kruger, P. A. Bingham

Materials Science and Engineering Faculty Research & Creative Works

This research has characterized the effects of P₂O₅ additions on the physical, chemical, thermal, rheological properties and the structure of SiO₂-B₂O₃-Na₂O glasses relevant to radioactive waste immobilization. Properties analyzed include high-temperature viscosity, glass transition temperature (T_g) and structure. X-ray diffraction (XRD) confirmed a solubility limit of between 3.0 and 4.0 mol% P₂O₅ for the onset of crystallinity with formation of Na₃PO₄ and Na₄P₂O₇ in annealed bulk glasses; and between 4.0 and 5.0 mol% P₂O …

Network Structures And The Properties Of Na-Ca-Sr-Borophosphate Glasses, Parker T. Freudenberger, Rebekah L. Blatt, Randall E. Youngman, Richard K. Brow

Mathematics and Statistics Faculty Research & Creative Works

Borophosphate glasses were prepared with the nominal molar compositions 16Na2O-(24-y)CaO-ySrO-xB2O3-(60-x)P2O5 (mol%), where 0≤x≤60 and y=0, 12, and 24. Information about the compositional dependence of borate and phosphate site speciation and next nearest neighbor linkages was obtained by 11B and 31P MAS NMR and Raman spectroscopies, and by high pressure liquid chromatography (HPLC). With the initial replacement of P2O5 by B2O3, tetrahedral borate sites linked to four phosphate anions, B(ØP)4, are created in the glass structure, and the average phosphate anion becomes smaller as bridging PØP bonds are replaced by bridging PØB bonds. With further increases in the B2O3 content, borate …

A Bilevel Game-Theoretic Decision-Making Framework For Strategic Retailers In Both Local And Wholesale Electricity Markets, Qiuyi Hong, Fanlin Meng, Jian Liu, Rui Bo

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes a bilevel game-theoretic model for multiple strategic retailers participating in both wholesale and local electricity markets while considering customers' switching behaviors. At the upper level, each retailer maximizes its own profit by making optimal pricing decisions in the retail market and bidding decisions in the day-ahead wholesale (DAW) and local power exchange (LPE) markets. The interaction among multiple strategic retailers is formulated using the Bertrand competition model. For the lower level, there are three optimization problems. First, the welfare maximization problem is formulated for customers to model their switching behaviors among different retailers. Second, a market-clearing problem …

Network Structures And The Properties Of Na-Ca-Sr-Borophosphate Glasses, Parker T. Freudenberger, Rebekah L. Blatt, Randall E. Youngman, Richard K. Brow

Materials Science and Engineering Faculty Research & Creative Works

Borophosphate glasses were prepared with the nominal molar compositions 16Na2O-(24-y)CaO-ySrO-xB2O3-(60-x)P2O5 (mol%), where 0≤x≤60 and y=0, 12, and 24. Information about the compositional dependence of borate and phosphate site speciation and next nearest neighbor linkages was obtained by 11B and 31P MAS NMR and Raman spectroscopies, and by high pressure liquid chromatography (HPLC). With the initial replacement of P2O5 by B2O3, tetrahedral borate sites linked to four phosphate anions, B(ØP)4, are created in the glass structure, and the average phosphate anion becomes smaller as bridging PØP bonds are replaced by bridging PØB bonds. With further increases in the B2O3 content, borate …

Network Structures And The Properties Of Na-Ca-Sr-Borophosphate Glasses, Parker T. Freudenberger, Rebekah L. Blatt, Randall E. Youngman, Richard K. Brow

Materials Science and Engineering Faculty Research & Creative Works

Borophosphate glasses were prepared with the nominal molar compositions 16Na₂O-(24-y)CaO-ySrO-xB₂O₃-(60-x)P₂O₅ (mol%), where 0≤x≤60 and y=0, 12, and 24. Information about the compositional dependence of borate and phosphate site speciation and next nearest neighbor linkages was obtained by ¹¹B and ³¹P MAS NMR and Raman spectroscopies, and by high pressure liquid chromatography (HPLC). With the initial replacement of P₂O₅ by B₂O₃, tetrahedral borate sites linked to four phosphate anions, B(ØP)₄, are created in the glass structure, and the average phosphate anion …

Demonstrating Non-Isothermal Vacuum Membrane Air Dehumidification For Efficient Next-Generation Air Conditioning, Andrew J. Fix, Shivam Gupta, James E. Braun, David M. Warsinger

School of Mechanical Engineering Faculty Publications

Vacuum membrane air dehumidification has gained significant interest in recent years as a highly efficient means of air dehumidification. Prior theoretical modeling work by the authors 1 introduced the Active Membrane Energy Exchanger (AMX) concept, which combines active heat exchange and vacuum membrane dehumidification into one non-isothermal system, and found that it could outperform other air conditioning technologies under many conditions. However, no experimental literature exists on combining active heat exchangers and vacuum membrane dehumidification. The goal of the present study is to evaluate the dehumidification (mass transfer) performance of the AMX concept relative to isothermal membrane dehumidification through three …

Residual Trapping Of Co2 And Enhanced Oil Recovery In Oil-Wet Sandstone Core – A Three-Phase Pore-Scale Analysis Using Nmr, Auby Baban, Alireza Keshavarz, Robert Amin, Stefan Iglauer

Research outputs 2022 to 2026

Hypothesis: Combining Carbon Geo-sequestration (CGS) with Enhanced Oil Recovery (EOR) in three-phase flow oil reservoirs is an effective and economically attractive technology to mitigate global warming caused by emission of anthropologic CO2 from fossil fuel combustion, as it offsets some of the costs of CO2 extraction. The targeted oil reservoirs display oil-wet characteristics, primarily because of the strong affinity of polar molecules present in oil; a mixture of a large number of chemical compounds to the rock's surface; and oil-wet surfaces that drastically reduce storage capacity of geological trapping mechanisms and increase the vertical migration of CO2. Thus, it is …

Wearable Sensing System For Noninvasive Monitoring Of Intracranial Biofluid Shifts In Aerospace Applications., Jacob L Griffith, Kim Cluff, Grant M Downes, Brandon Eckerman, Subash Bhandari, Benjamin E Loflin, Ryan Becker, Fayez Alruwaili, Noor Mohammed

Henry M. Rowan College of Engineering Departmental Research

The alteration of the hydrostatic pressure gradient in the human body has been associated with changes in human physiology, including abnormal blood flow, syncope, and visual impairment. The focus of this study was to evaluate changes in the resonant frequency of a wearable electromagnetic resonant skin patch sensor during simulated physiological changes observed in aerospace applications. Simulated microgravity was induced in eight healthy human participants (n = 8), and the implementation of lower body negative pressure (LBNP) countermeasures was induced in four healthy human participants (n = 4). The average shift in resonant frequency was -13.76 ± 6.49 MHz for …

Temperature, Pressure, And Adsorption Dependent Redox Potentials: Iii. Processes Of Co Conversion To Value-Added Compounds, Siyuan Fang, Yun Hang Hu

Michigan Tech Publications, Part 1

Carbon monoxide (CO) is a primary air pollutant and a poisonous species for human beings, animals, and some catalytic reactions. Meanwhile, CO is also a versatile feedstock in the chemical industry to produce high‐value chemicals and clean fuels, which has stimulated extensive research interests in exploiting efficient CO conversion processes. Redox potential is a key thermodynamic quantity in these processes whereas only standard reduction potentials at 25°Cand 1 atm are currently available. Herein, it is the first time to report the effects of temperature (0–1000°C), pressure (1–100 atm), and adsorption on the redox potentials of 18 CO conversion reactions to …

Enhancing The Biological Oxidation Of H2s In A Sewer Pipe With Highly Conductive Concrete And Electricity-Producing Bacteria, Huy Thanh Vo, Tsuyoshi Imai, Masato Fukushima, Kanathip Promnuan, Tasuma Suzuki, Hiraku Sakuma, Takashi Hitomi, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Hydrogen sulfide (H2S) generated in sewer systems is problematic to public health and the environment, owing to its corrosive consequences, odor concerns, and poison control issues. In a previous work, conductive concrete, based on amorphous carbon with a mechanism that operates as a microbial fuel cell was investigated. The objective of the present study is to develop additional materials for highly conductive concrete, to mitigate the concentration of H2S in sewer pipes. Adsorption experiments were conducted to elucidate the role of the H2S reduction. Additionally, electricity-producing bacteria (EPB), isolated from a municipal wastewater treatment plant, were inoculated to improve the …

Invariant-Set Design Of Robust Switched Trackers For Bidirectional Power Converters In Hybrid Microgrids, Ehab Bayoumi

Mechanical Engineering

The small-signal stability of a hybrid (DC/AC) microgrid is highly affected by the direction and amount of power flow through the interlinking converter (IC). This article proposes an invariant-set design of nondroop tracker (to follow the desired time-varying reference) for controlling the power flow in hybrid microgrids in both inversion and rectification modes. The proposed tracker provides fast response, zero steady state error, and robustness against system uncertainty. Since the invariant-set is difficult to calculate, it is approximated using a bounding ellipsoid (being a linear function, and the problem reduces to convex optimization, easy to solve). A novel linear matrix …

Introduction To Control Engineering, Xiangyu Meng

E-Textbooks

This is an introductory level textbook for control engineering.

Optical Sensing Technologies To Elucidate The Interplay Between Plant And Microbes, Asia Neelam, Shawana Tabassum

Electrical Engineering Faculty Publications and Presentations

Plant-microbe interactions are critical for ecosystem functioning and driving rhizosphere processes. To fully understand the communication pathways between plants and rhizosphere microbes, it is crucial to measure the numerous processes that occur in the plant and the rhizosphere. The present review first provides an overview of how plants interact with their surrounding microbial communities, and in turn, are affected by them. Next, different optical biosensing technologies that elucidate the plant-microbe interactions and provide pathogenic detection are summarized. Currently, most of the biosensors used for detecting plant parameters or microbial communities in soil are centered around genetically encoded optical and electrochemical …

Locally Resonant Metasurface For Low-Frequency Transmissive Underwater Acoustic Waves, Zhong Chen, Shenghong Guan, Qiang Xie, Zheng Li, Zhongmei Gao, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Acoustic metasurfaces for underwater wave manipulation have great potential use, but the strong solid-fluid interaction caused by impedance closeness between the structure and water brings design difficulty, especially in the low-frequency range.

Methods: Here a locally resonant metasurface for transmissive underwater acoustic waves is proposed using finite element method for which each metasurface unit consists of one channel and three subunits. Each subunit has one plate and two rubber spacers to form a resonator. By changing the height ratio of the plate over the subunit, arbitrary phase shifts within the full 2π coverage can be obtained at …

A Networked Radar System For Tracking Small Unmanned Aircraft Systems, Douglas Graff

Theses and Dissertations

Tracking small unmanned aircraft systems (SUAS) becomes increasingly important with their increased use in populated areas. We propose an effective tracking solution for SUAS using a networked system of one-dimensional scanning radars. Tracking SUAS with a network of radar systems requires extrinsic calibration of each radar to a common frame. We provide a calibration solution using an orthogonal Procrustes formulation that associates radar measurements from the ground-mounted radar to real-time-kinematic Global Positioning System (RTK-GPS) data. Two variations of the calibration are presented, an online and batch processing method. Outdoor hardware experiments validate the capabilities of the radar network in tracking …

Editorial: Advances In Acoustic/Elastic Wave Sensing For Information Processing, Taehwa Lee, Chen Shen, Qingbo He

Henry M. Rowan College of Engineering Departmental Research

No abstract provided.

Subtypes Of Relapsing-Remitting Multiple Sclerosis Identified By Network Analysis, Quentin Howlett-Prieto, Chelsea Oommen, Michael D. Carrithers, Donald C. Wunsch, Daniel B. Hier

Electrical and Computer Engineering Faculty Research & Creative Works

We used network analysis to identify subtypes of relapsing-remitting multiple sclerosis subjects based on their cumulative signs and symptoms. The electronic medical records of 113 subjects with relapsing-remitting multiple sclerosis were reviewed, signs and symptoms were mapped to classes in a neuro-ontology, and classes were collapsed into sixteen superclasses by subsumption. After normalization and vectorization of the data, bipartite (subject-feature) and unipartite (subject-subject) network graphs were created using NetworkX and visualized in Gephi. Degree and weighted degree were calculated for each node. Graphs were partitioned into communities using the modularity score. Feature maps visualized differences in features by community. Network …

Solar-Light-Responsive Nanomaterials For The Photoelectrocatalytic Degradation Of Stubborn Pollutants, Benjamin O. Orimolade, Azeez O. Idris, Seyi Philemon Akanji, Folahan A. Adekola, Shohreh Azizi, Malik Maaza, Bhekie Mamba

Research outputs 2022 to 2026

Due to the ever increasing demand for cleaner water, a remarkable focus has been on the use of nanomaterials in wastewater treatment application. Photoelectrocatalytic (PEC) degradation, an advanced oxidation process which combines light and electrical energy, has been identified as a suitable technique capable of achieving total mineralisation of recalcitrant organic pollutants in wastewater. PEC degradation is non-selective, environmentally friendly and possesses great efficiency. The efficiency of PEC degradation has been enhanced by fabricating the photoanodes on a nanoscale with distinct morphologies. These nanostructured photoanodes have been extensively used for the removal of pharmaceuticals, dyes and phenolic water from wastewater. …

Liquid-Liquid Equilibria Of Water + Ethanol + Castor Oil And The Effect Of Cellulose Nanocrystal/Fe3o4 And Lignin/Fe3o4 Nanoparticles, Mohammad J. Hasan, Fariba Yehaneh, Amy Ciric, Peng Chen, Erick S. Vasquez, Esteban E. Ureña-Benavides

Chemical and Materials Engineering Faculty Publications

Castor oil has been proposed as a renewable solvent for the liquid extraction of ethanol from water as an alternative to more traditional energy intensive distillation-based methods. The liquid–liquid equilibrium (LLE) of the ternary system water + ethanol + castor oil was determined at 295.15 K using high performance liquid chromatography (HPLC). Castor oil was herein treated as a pseudo-component with the molecular weight of the triglyceride of ricinoleic acid. The experimental data was fitted to the UNIQUAC and NRTL models to obtain parameters for castor oil, and binary interaction parameters for castor oil/ethanol and castor oil/water pairs. The separation …

Skyqube: Developing Tools For Stem Education Focusing On Space System Engineering, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "SkyQube: Developing Tools for STEM Education Focusing on Space System Engineering" from January 11, 2023.

Enhancing Student'sperformance Classification Using Ensemble Modeling, Ahmed Adil Nafea, Muthanna Mishlish, Ali Muwafaq Haban Shaban, Mohammed M. Al-Ani, Khattab M Ali Alheeti, Hussam J. Mohammed

Iraqi Journal for Computer Science and Mathematics

A precise prediction of student performance is an important aspect withineducational institutions to improve results and provide personalized support ofstudents.However, the predication accuracy of student performance considers anopenissue within education field.Therefore, thispaper proposes a developedapproachto identifyperformance of students using a group modeling. This approach combinesthe strengths of multiple algorithms including random forest (RF), decision tree (DT), AdaBoosts, and support vector machine (SVM). Afterward, thelastensemble estimatesas one of the bets logistic regressionmethodswas utilizedto create a robust and reliable predictive modelbecause it considers The experiments were evaluated usingtheOpen University Learning Analytics Dataset (OULAD)benchmark dataset.The OULADdataset considersa comprehensive dataset containingvarious characteristics related to …