Engineering Commons^™

Lateral Torsional Buckling Resistance Of Continuous Steel Stringers In Existing Bridges, Dinesha Malky Kuruppuarachchi Kuruppuarachchi Appuhamilage Don

Master's Theses

Some of the Louisiana’s bridges built in the 1950s and 1960s used two-girder or truss systems, in which floorbeams are carried by main members and the continuous (spliced) stringers are supported by the floorbeams. The main members are either two edge (fascia) girders or trusses. When the flexural capacity of continuous stringers is calculated, the moment gradient factor (Cb) is not accurately calculated considering the lateral torsional buckling (LTB) at the negative moment section. In particular, the bracing effect of the non-composite concrete deck is not accounted for, and as a result, the current practice has underestimated the LTB strength …

Epi-Mucosa Fixation And Autologous Platelet-Rich Fibrin Treatment In Medication-Related Osteonecrosis Of The Jaw, Antonio Cortese, Antonio Casarella, Candace M. Howard, Pier Paolo Claudio

Faculty and Student Publications

Medication-related osteonecrosis of the jaw (MRONJ) frequently affects patients after treatments with bisphosphonates or denosumab, especially with high doses in patients with bone osteoporosis, neoplastic metastases, or possibly anti-angiogenic treatment for cancer. The aim of this article was to show a new treatment planning for stage 2 and stage 3 MRONJ using platelet-rich fibrin (PRF) at the surgical field to enhance healing in association with a new epi-mucosal fixation technique to prevent or treat mandibular fracture. Two cases were treated by epi-mucosa fixation and autologous PRF use for prevention of mandibular fracture risks related to necrotic bone resection or a …

Atomic Oxygen Resistant Low Earth Orbit Stable Polymer Matrix Composites Employing Phenylphosphine Oxide Epoxy-Amines, Witold Fuchs

Dissertations

Atomic oxygen (AO) attacks polymer matrix composites (PMC’s) on the surfaces of spacecraft in low earth orbit (LEO) and threatens safe spacecraft operation and service life. Incorporating phenylphosphine oxide (PPO) groups into polymer chains offers a self-regenerating method of protection from AO but remains poorly understood. Herein, epoxies containing PPO groups were synthesized with increasing concentrations of phosphorus [P] from 0 to 8 wt % to investigate their AO resistance. Measurements confirmed the exposure of these materials to AO produces a passivation phosphate (POx) layer on the surface of the sample and the efficacy of the resultant layer was directly …

Voltage-Controlled Magnetic Anisotropy In Antiferromagnetic Mgo-Capped Mnpt Films, P. H. Chang, Wuzhang Fang, T. Ozaki, Kirill Belashchenko

Kirill Belashchenko Publications

The magnetic anisotropy in MgO-capped MnPt films and its voltage control are studied using first-principles calculations. Sharp variation of the magnetic anisotropy with film thickness, especially in the Pt-terminated film, suggests that it may be widely tuned by adjusting the film thickness. In thick films the linear voltage control coefficient is as large as 1.5 and -0.6 pJ/Vm for Pt-terminated and Mn-terminated interfaces, respectively. The combination of a widely tunable magnetic anisotropy energy and a large voltage-control coefficient suggest that MgO-capped MnPt films can serve as a versatile platform for magnetic memory and antiferromagnonic applications.

Malicious Hardware & Its Effects On Industry, Gustavo Perez

Computer Science and Computer Engineering Undergraduate Honors Theses

In recent years advancements have been made in computer hardware security to circumnavigate the threat of malicious hardware. Threats come in several forms during the development and overall life cycle of computer hardware and I aim to highlight those key points. I will illustrate the various ways in which attackers exploit flaws in a chip design, or how malicious parties take advantage of the many steps required to design and fabricate hardware. Due to these exploits, the industry and consumers have suffered damages in the form of financial loss, physical harm, breaches of personal data, and a multitude of other …

Evaluating The Thermal Conductivity Of Potting Materials Using The Hot-Wire Method, Yeny Hau Chen

Electrical Engineering Undergraduate Honors Theses

This thesis is focused on the evaluation of the thermal conductivity of certain potting materials, in particular Aluminum Nitride (AlN), thermal putty, and silicone oil using the “hot-wire” method in order to allow volume reductions of inductors, and thus, increase the power density of converters. The main objective of this thesis is then to study the behavior of these specific materials intended for high-density power converters by mixing them with different proportions and placing the resulting compounds into a can for calculating their thermal conductivities, in order to evaluate the effects on the power density of inductor-based converters. One objective …

Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker

Electrical Engineering Undergraduate Honors Theses

The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the Dupont^TM GreenTape^TM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …

Wood City: Timberizing The City’S Building Blocks, Community Design Center

Community Design Center Project Reports

Exogenous forces are reshaping building markets among the 19 real estate product sectors comprising most of America’s built environment. The real estate development value chain is being recast in sectors like fuel retail, fast food, grocery, and warehousing, while new venture-capital interventions are hybridizing housing, hospitality, healthcare, and the senior services markets in value-adding ways. Meanwhile, pockets of low-density metropolitan fabrics—the non-downtown environments encompassing suburbs, small towns, villages, edge cities, exurban areas, and rural areas, which house 85 percent of America’s population —are densifying in response to consumer demand for walkable, mixed-use environments. Disruptions are driving innovation in each of …

Fast Flow Reconstruction Via Robust Invertible N X N Convolution, Thanh-Dat Truong, Chi Nhan Duong, Minh-Triet Tran, Ngan Le, Khoa Luu

Computer Science and Computer Engineering Faculty Publications and Presentations

Flow-based generative models have recently become one of the most efficient approaches to model data generation. Indeed, they are constructed with a sequence of invertible and tractable transformations. Glow first introduced a simple type of generative flow using an invertible 1x1 convolution. However, the 1x1 convolution suffers from limited flexibility compared to the standard convolutions. In this paper, we propose a novel invertible n x n convolution approach that overcomes the limitations of the invertible 1x1 convolution. In addition, our proposed network is not only tractable and invertible but also uses fewer parameters than standard convolutions. The experiments on CIFAR-10, …

Data Forgery Detection In Automatic Generation Control: Exploration Of Automated Parameter Generation And Low-Rate Attacks, Yatish R. Dubasi

Computer Science and Computer Engineering Undergraduate Honors Theses

Automatic Generation Control (AGC) is a key control system utilized in electric power systems. AGC uses frequency and tie-line power flow measurements to determine the Area Control Error (ACE). ACE is then used by the AGC to adjust power generation and maintain an acceptable power system frequency. Attackers might inject false frequency and/or tie-line power flow measurements to mislead AGC into falsely adjusting power generation, which can harm power system operations. Various data forgery detection models are studied in this thesis. First, to make the use of predictive detection models easier for users, we propose a method for automated generation …

Neural Network With Nlp, Harshita Sharma, Tinkle Jain

School of Professional Studies

This thesis is about neural networks and how their algorithmic systems work. Neural networks are well-suited to aiding people with complex challenges in real-world situations. Thesis topics include nonlinear and complicated interactions between inputs and outputs, as well as making inferences, discovering hidden links, patterns, and predictions, and modeling highly volatile data and variations to forecast uncommon events. Neural networks have the potential to help people make better decisions. NLP is a technique for analyzing, interpreting, and comprehending large amounts of text. We can no longer evaluate the text using traditional approaches due to the massive volumes of text data …

Assessment And Improvement Of Performance Of Septic Systems In Cold Climates (Year 1), Stu Geza, Todd Menkhaus, Lianping Li, Galen Hoogestraat

SDWRI Publications and Reports

Onsite septic systems are used for wastewater treatment for households not connected to sewers. There is a concern about surface and groundwater pollution when effectiveness becomes limited due to soil texture, soil temperature, neighborhood density, and distance to water resources. The goal of this study was to assess treatment performance of local soils and selected treatment media. Lab-scale column experiments were conducted using wastewater from Wastewater Reclamation Facility in Rapid City. The experiments were conducted inside and outside the lab to evaluate the effect of temperature. The columns outside the lab were subject to seasonal variation in temperature. Moisture content, …

Post Covid-19 Water And Waste Water Management To Protect Public Health And Geoenvironment, Ken Cornell, Arvin Farid

Chemistry and Biochemistry Faculty Publications and Presentations

The coronavirus disease 2019 pandemic has posed severe threats to humans and the geoenvironment. The findings of severe acute respiratory syndrome coronavirus 2 (Sars-CoV-2) traces in waste water and the practice of disinfecting outdoor spaces in several cities in the world, which can result into the entry of disinfectants and their by-products into storm drainage systems and their subsequent discharge into rivers and coastal waters, raise the issue of environmental, ecological and public health effects. The aims of the current paper are to investigate the potential of water and waste water to operate as transmission routes for Sars-CoV-2 and the …

A Review Of Harmful Algal Bloom Prediction Models For Lakes And Reservoirs, Jade Snyder Echard

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Anthropogenic activity has led to eutrophication in water bodies across the world. This eutrophication promotes blooms, cyanobacteria being among the most notorious bloom organisms. Cyanobacterial blooms (more commonly referred to as harmful algal blooms (HABs)) can devastate an ecosystem. Cyanobacteria are resilient microorganisms that have adapted to survive under a variety of conditions, often outcompeting other phytoplankton. Some species of cyanobacteria produce toxins that ward off predators. These toxins can negatively affect the health of the aquatic life, but also can impact animals and humans that drink or come in contact with these noxious waters. Although cyanotoxin’s effects on humans …

Expanding Image Datasets For Deep Learning By Evaluating Independence Through Coefficient Correlation And Mean-Squared Error, Ayman Yousef

Biomedical Engineering Undergraduate Honors Theses

With deep learning being leveraged more regularly in the field of image classification, particularly in medical imaging, network optimizations have become a field in and of itself. With open source, comprehensive medical image datasets few and far, computational dataset expansion has become a useful tool for researchers without the ability to further manually collect data. However, with the rich amount of data that imaging modalities like multi-photon microscopy collect at a time, there is potential to expand datasets through proper utilization of this data that often time goes unused. Previous deep learning studies have shown that improper expansion can conflate …

Transimpedance Amplification Of Optocoupler Output For High Temperature Applications, Kara Maurer

Electrical Engineering Undergraduate Honors Theses

When looking to the future of electronics, one characteristic is becoming more lucrative: high temperature capabilities. With the goals of not only becoming more efficient electronically, spatially, and cost-wise, adapting electronics for a high temperature environment can potentially be a route to all three of these goals. Not only does it take away the need for a cooling method, but it can also increase the longevity of a product which can make it even more cost effective. In an effort to contribute to the push for high temperature electronics, the University of Arkansas is developing a high temperature power module …

Optoelectronic Valley-Spin Qubits With Ambipolar Quantum Dots, Jeremy Tull

Electrical Engineering Undergraduate Honors Theses

The current limitations of qubit-based processors are caused by imperfections in quantum gates, leading to a lack of gate fidelity. Gate fidelity can be refined by extending the coherence of qubits and reducing logic operation speed. A potential solution is to develop a hybrid qubit that has the coherence of electrically-controlled quantum dots and the gate speed of their optically-controlled counterparts. Quantum bits that utilize ultrafast optical gating to perform gate operations require precise control of the gating pulse duration. Optical dispersion can cause adverse effects pulse duration, such as pulse broadening, so dispersion-compensation techniques must be employed; by properly …

Guide Rnas Preparation For In-Vitro Crispr-Cas9 Complex Delivery Targeting Genes That Affect Wound Healing., Prashant Khatiwada

Biomedical Engineering Undergraduate Honors Theses

CRISPR-Cas9 technology has widely been used as a viable genome engineering platform to make site-specific insertion, deletion, and breaks. The nuclease dead version of Cas9 or dCas9 can be used for the activation and repression of target gene sites using specific activation or repression domains. In this study, CRISPR guide RNAs were designed for a CRISPR inhibition approach to repress the transcriptional activity of the target genes. An expression plasmid vector composed of a U6 promoter sequence, BbsI restriction sites, and a chimeric gRNA sequence was digested, and the phosphorylated forward and reverse gRNAs were ligated with the plasmid vector. …

Ironless, Axial Flux, Electric Bldc Motor For Aircraft Electric Propulsion, Kevin W. Hobbs

Electrical Engineering Undergraduate Honors Theses

3D printing has shown much promise as a method of rapidly manufacturing lightweight ironless motors to meet the growing demand that airlines have for more cost-effective products that reduce emissions and flight prices. 3D-printed ironless, axial flux, electric BLDC motors would meet these needs with both their high efficiency and power density.

A Halbach array motor was designed and 3D-printed for the analysis of its magnetic properties to gain more insight about it performance. Fusion 360 was used to design the 3D drawings of the motor parts. The rotor, stator, and stator mount were designed to accommodate the sizes of …

An Examination Of Grid Stability As It Relates To The Increased Integration Of Inverter-Based Resources, Daniel Voss

Electrical Engineering Undergraduate Honors Theses

There is currently a growing interest in increasing the amount of renewable energy resources connected to the bulk electric system (BES) that stems from various environmental, political, and social concerns. However, the differences between conventional generation resources and inverter-based resources (IBR)—namely wind and solar—pose new issues that make this increased integration a larger problem. In other studies, the increased penetration of renewable energy resources has resulted in weak-grid systems that are more susceptible to collapse. This comes as a result from the inability for IBRs to effectively provide enough reactive power, an effect especially apparent during fault conditions, which the …

Effect Of Silicon Carbide On Electric Drivetrains Of Heavy-Duty Vehicles, Haley Solera

Electrical Engineering Undergraduate Honors Theses

The application of electro-mechanical motors in rigorous, high-temperature systems is constantly adapting to suit the growing needs of developers in the automotive, construction, and aerospace industries. With improved efficiency, torque, and environmental impact over conventional internal combustion engines, electric drive trains pose more than ample incentive for manufacturers to invest considerable resources toward the design of newer, better methods of electric propulsion. This paper discusses the motives behind the electrification of heavy-duty vehicles, the state-of-the-art technology currently available on the market, and the novel application of silicon carbide to electric drive trains as a means of increasing their heat tolerance, …

Using Deep Learning To Analyze Materials In Medical Images, Carson Molder

Computer Science and Computer Engineering Undergraduate Honors Theses

Modern deep learning architectures have become increasingly popular in medicine, especially for analyzing medical images. In some medical applications, deep learning image analysis models have been more accurate at predicting medical conditions than experts. Deep learning has also been effective for material analysis on photographs. We aim to leverage deep learning to perform material analysis on medical images. Because material datasets for medicine are scarce, we first introduce a texture dataset generation algorithm that automatically samples desired textures from annotated or unannotated medical images. Second, we use a novel Siamese neural network called D-CNN to predict patch similarity and build …

Environmental Geotechnics: Challenges And Opportunities In The Post-Covid-19 World, Arvin Farid

Civil Engineering Faculty Publications and Presentations

The outbreak of the coronavirus disease 2019 (Covid-19) pandemic not only has created a health crisis across the world but is also expected to impact negatively the global economy and societies at a scale that is maybe larger than that of the 2008 financial crisis. Simultaneously, it has inevitably exerted many negative consequences on the geoenvironment on which human beings depend. The current paper articulates the role of environmental geotechnics in elucidating and mitigating the effects of the current pandemic. It is the belief of all authors that the Covid-19 pandemic presents not only significant challenges but also opportunities for …

Stand-Alone Direct Current Power Network Based On Photovoltaics And Lithium-Ion Batteries For Reverse Osmosis Desalination Plant, Vishwas Powar, Rajendra Singh

Publications

Plummeting reserves and increasing demand of freshwater resources have culminated into a global water crisis. Desalination is a potential solution to mitigate the freshwater shortage. However, the process of desalination is expensive and energy-intensive. Due to the water-energy-climate nexus, there is an urgent need to provide sustainable low-cost electrical power for desalination that has the lowest impact on climate and related ecosystem challenges. For a large-scale reverse osmosis desalination plant, we have proposed the design and analysis of a photovoltaics and battery-based stand-alone direct current power network. The design methodology focusses on appropriate sizing, optimum tilt and temperature compensation techniques …

Lateral Torsional Buckling Resistance Of Continuous Steel Stringers In Existing Bridges, Dinesha Malky Kuruppuarachchi Kuruppuarachchi Appuhamilage Don

Doctoral Dissertations

Some of the Louisiana’s bridges built in the 1950s and 1960s used two-girder or truss systems, in which floorbeams are carried by main members and the continuous (spliced) stringers are supported by the floorbeams. The main members are either two edge (fascia) girders or trusses. When the flexural capacity of continuous stringers is calculated, the moment gradient factor (Cb) is not accurately calculated considering the lateral torsional buckling (LTB) at the negative moment section. In particular, the bracing effect of the non-composite concrete deck is not accounted for, and as a result, the current practice has underestimated the LTB strength …

Glial Endothelial Brain Cell Co-Cultures For Testing Signaling Response And Delivery Of Novel Materials Across Blood Brain Barrier, Neela Prajapati

Doctoral Dissertations

The brain accounts for 20% of overall energy metabolism in the body though it just comprises 2% of the total body mass but has a limited capacity of storing energy unlike other critical organs in the body such as the heart and liver. This energy along with oxygen and nutrients is supplied by cerebral blood flow (CBF), any interruption of which can cease the brain function within seconds with a potential irreversible neuronal injury, within minutes. Vascular cells along with astrocytes and neurons are a part of a recently developed concept known as the Neurovascular Unit responsible for Neurovascular coupling …

Shallow 3d Shear Wave Velocity Model And Revised Site Period Prediction Map For The Mexico City Basin, Rendon Martin Rieth

Graduate Theses and Dissertations

The goal of this study was to revise the existing site period prediction map and to develop a shallow 3D shear wave velocity model of the Mexico City Basin. To accomplish this goal, an extensive literature review was performed to compile as much pertinent shear wave velocity and site period data for the region. In total, 75 sites were used to revise the site period prediction map and 40 sites were used to develop the shear wave velocity model. The 2004 Complementary Technical Standards of Mexico site period prediction map was adjusted with new site period measurements across the basin …

Comparison Of The Resistance Of Belitic Calcium Sulfoaluminate Cement And Portland Cement To Sulfate Attack And Sulfuric Acid, Rilye Dillard

Graduate Theses and Dissertations

Microbially induced corrosion (MIC) is a fairly common concrete deterioration mechanism with many negative effects. MIC is a complex chemical and biological process that occurs in sewage systems and is nearly impossible to replicate in a laboratory setting. For this study, sulfate and sulfuric acid attack on concrete were studied to mimic two stages of the MIC process. The ASTM C1012, Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution and a modified ASTM C1012 accelerated method were used to compare the sulfate resistance of belitic calcium sulfoaluminate (BCSA) cement, portland cement (PC), and PC-fly …

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

Experimental Design And Preliminary Testing For Skewed Special Moment Frame Prequalification, Sara Alimirzaei

Graduate Theses and Dissertations

Special moment frames having specially detailed connections are common in high seismic regions, providing architectural flexibility for passageways and views without brace obstructions. In situations where the building framing layout requires deviation from typical rectangular framing, skew in the moment frame connections may be required. Currently, the AISC prequalified connections only include testing of orthogonal moment frame connections and it is unclear whether the existing design methods can accommodate skew at the beam-to- column connections. To investigate the effect of out-of-plane skew on the performance of reduced beam section special moment frame connections, an experimental test is designed and a …