Engineering Commons^™

A Multiple Scattering Method To Study The Cable Harness Inside A Vehicle Shell, Yansheng Wang

Doctoral Dissertations

"This dissertation contains three major parts. In the first part, a generalized multi-conductor transmission line (GMTL) method is proposed to model a cable harness. In the GMTL method, all wires of the cable harness take the infinity as the reference. In such a way, the GMTL method takes into account not only the transmission-line mode but also the antenna-mode current on the cable harness. Further, by employing the GMTL method and the mixed-potential integral equations (MPIE) method in a multiple scattering (MS) procedure, it enables an efficient and accurate approach to evaluate the current distribution on a cable harness with …

Learning-Based Short-Time Prediction Of Photovoltaic Resources For Pre-Emptive Excursion Cancellation, Huaiqi Xie

Doctoral Dissertations

"There is a growing interest in using renewable energy resources (RES) such as wind, solar, geothermal and biomass in power systems. The main incentives for using renewable energy resources include the growing interest in sustainable and clean generation as well as reduced fuel cost. However, the challenge with using wind and solar resources is their indeterminacy which leads to voltage and frequency excursions. In this dissertation, first, the economic dispatch (ED) problem for a community microgrid is studied which explores a community energy market. As a result of this work, the importance of modeling and predicting renewable resources is understood. …

Experimental And Numerical Investigation On Tar Production And Recycling In Fixed Bed Biomass Gasifiers, Jia Yu

Doctoral Dissertations

"Bioenergy has been utilized for domestic purposes since pre-recorded history and it catches the highlight in the recent decades because it naturally benefits the world climate and energy security. Gasification is one of the key technologies to efficiently and economically convert biomass into syngas and further into biofuels. Despite these outstanding advantages, biomass gasification suffers from the formation of unfavorable byproduct tar and the consequential tar elimination. Moreover, the collected tar is toxic and thus requires storage and strict deposit method to avoid environmental pollution.

To understand the mechanisms of biomass gasification and tar production, simulations with Aspen Plus were …

Investigation Of Microstructure And Mechanical Properties By Direct Metal Deposition, Jingwei Zhang

Doctoral Dissertations

"Microstructure and properties of Direct Metal Deposition (DMD) parts are very crucial to meeting industrial requirements of parts quality. Prediction, and control of microstructure and mechanical properties have attracted much attention during conventional metal manufacturing process under different conditions. However, there is few investigations focused on microstructure simulation and mechanical properties control under different process parameters during DMD process. This dissertation is intended to develop a multiscale model to investigate Ti6Al4V grain structure development and explore Ti6Al4V based functionally graded material (FGM) deposit properties during DMD process. The first research topic is to investigate and develop a cellular automaton-finite element …

Machine Learning Techniques Implementation In Power Optimization, Data Processing, And Bio-Medical Applications, Khalid Khairullah Mezied Al-Jabery

Doctoral Dissertations

"The rapid progress and development in machine-learning algorithms becomes a key factor in determining the future of humanity. These algorithms and techniques were utilized to solve a wide spectrum of problems extended from data mining and knowledge discovery to unsupervised learning and optimization. This dissertation consists of two study areas. The first area investigates the use of reinforcement learning and adaptive critic design algorithms in the field of power grid control. The second area in this dissertation, consisting of three papers, focuses on developing and applying clustering algorithms on biomedical data. The first paper presents a novel modelling approach for …

Monitoring Of Hybrid Manufacturing Using Acoustic Emission Sensor, Haythem Gaja

Doctoral Dissertations

"The approach of hybrid manufacturing addressed in this research uses two manufacturing processes, one process builds a metal part using laser metal deposition, and the other process finishes the part using a milling machining. The ability to produce complete functioning parts in a short time with minimal cost and energy consumption has made hybrid manufacturing popular in many industries for parts repair and rapid prototyping. Monitoring of hybrid manufacturing processes has become popular because it increases the quality and accuracy of the parts produced and reduces both costs and production time. The goal of this work is to monitor the …

Integrated Study On The Applicability Of Co₂-Eor In Unconventional Liquids Rich Reservoirs, Dheiaa Khafief Khashan Alfarge

Doctoral Dissertations

"Unconventional Liquids Rich Reservoirs (ULR) such as Bakken, Niobrara, and Eagle Ford have become the main target for oil and gas investors as conventional formations started to deplete and diminish in number. These unconventional plays have a huge oil reserve; however, the predicted primary oil recovery is still low as an average of 7.5 %. Unconventional Improved Oil Recovery (UIOR) techniques are still a new concept in the oil industry because there is no commercial project for any IOR technique so far. Injecting carbon dioxide (CO₂) might be the most potential strategy to improve oil recovery in such complex plays. …

Mitigation Of Environmental Hazards Of Sulfide Mineral Flotation With An Insight Into Froth Stability And Flotation Performance, Muhammad Badar Hayat

Doctoral Dissertations

"Today's major challenges facing the flotation of sulfide minerals involve constant variability in the ore composition; environmental concerns; water scarcity and inefficient plant performance. The present work addresses these challenges faced by the flotation process of complex sulfide ore of Mississippi Valley type with an insight into the froth stability and the flotation performance. The first project in this study was aimed at finding the optimum conditions for the bulk flotation of galena (PbS) and chalcopyrite (CuFeS₂) through Response Surface Methodology (RSM). In the second project, an attempt was made to replace toxic sodium cyanide (NaCN) with the biodegradable chitosan …

Development And Management Of Advanced Batteries Via Additive Manufacturing And Modeling, Jie Li

Doctoral Dissertations

"The applications of Li-ion batteries require higher energy and power densities, improved safety, and sophisticated battery management systems. To satisfy these demands, as battery performances depend on the network of constituent materials, it is necessary to optimize the electrode structure. Simultaneously, the states of the battery have to be accurately estimated and controlled to maintain a durable condition of the battery system. For those purposes, this research focused on the innovation of 3D electrode via additive manufacturing, and the development of fast and accurate physical based models to predict the battery status for control purposes. Paper I proposed a novel …

Electrodeposited Semiconductor Nanostructures & Epitaxial Thin Films For Flexible Electronics, Naveen Kumar Mahenderkar

Doctoral Dissertations

"Single-crystal Si is the bedrock of semiconductor devices due to the high crystalline perfection which minimizes electron-hole recombination, and the dense native silicon oxide which minimizes surface states. To expand the palette of electronic materials beyond planar Si, an inexpensive source of highly ordered material is needed that can serve as an inert substrate for the epitaxial growth of grain boundary-free semiconductors, photonic materials, and superconductors. There is also a need for a simple, inexpensive, and scalable fabrication technique for the growth of semiconductor nanostructures and thin films. This dissertation focuses on the fabrication of semiconducting nanowires (polycrystalline Ge & …

Computational Design And Numerical Analyses Of Thermal-Hydraulics In A Pwr-Type Small Modular Nuclear Reactor, Vivek Murlidhar Rao

Doctoral Dissertations

"This dissertation focuses on computational design of a PWR-type small modular nuclear reactor (SMR), and analysis of coolant thermal-hydraulics during steady-state operation. Physical design of the SMR is based on the existing AP-1000 and Small Modular Reactor designs by Westinghouse Nuclear.

The first paper discusses a two-stage simulation of turbulent flow in the lower plenum of the RPV. In the first stage, four time-dependent Reynolds-Averaged Navier-Stokes (RANS) based turbulence models were used to simulate turbulent flow, compare predictions and identify an appropriate turbulence model. In the second stage, the selected turbulence model was once again used to simulate flow on …

The Separation Of Shear-Driven Liquid Films From A Sharp Corner, Zahra Sadeghizadeh

Doctoral Dissertations

"The separation of shear-driven liquid films occurs in many engineering applications such as port fuel injected engines, demisters, and gas transfer lines. Despite the importance of this problem, the details of the interaction between operating parameters such as liquid flow rate, gas velocities and liquid film properties on the forces at the expanding corner are still not clear. To enhance the insight on the complicated interaction between the gas and liquid phases, the shear-driven liquid flow around a corner has been studied both experimentally and analytically in this work. The effect of the complex liquid film structure on liquid mass …

A Methodology To Predict Community College Stem Student Retention And Completion, Jennifer Lynn Snyder

Doctoral Dissertations

"Numerous government reports point to the multifaceted issues facing the country's capacity to increase the number of STEM majors, while also diversifying the workforce. Community colleges are uniquely positioned as integral partners in the higher education ecosystem. These institutions serve as an access point to opportunity for many students, especially underrepresented minorities and women. Community colleges should serve as a major pathway to students pursuing STEM degrees; however student retention and completion rates are dismally low. Therefore, there is a need to predict STEM student success and provide interventions when factors indicate potential failure. This enables educational institutions to better …

Multi-Scale Investigation Of Microstructure, Fiber-Matrix Bond, And Mechanical Properties Of Ultra-High Performance Concrete, Zemei Wu

Doctoral Dissertations

"The main objective of this study is to provide new insights into enhancing fiber-matrix bond and mechanical properties of ultra-high performance concrete (UHPC). Three main strategies were investigated: 1) use of supplementary cementitious materials; 2) use of nano-particles; and 3) use of deformed fibers. A multi-scale investigation involving the evaluation of non-fibrous UHPC mortar phase (matrix), fiber-matrix interface phase, and then UHPC composite material was undertaken to determine microstructural characteristics, fiber bond to matrix, and key mechanical properties of the UHPC matrix and UHPC. Test results indicate that the incorporation of 10%-20% silica fume effectively improved the fiber-matrix bond and …

Limiting Key Drilling Parameters To Control Mud Losses In Basra's Oil Fields, Iraq, Abo Taleb Tuama Al-Hameedi

Doctoral Dissertations

"Wells in Basra's oil fields are highly susceptible to lost circulation problems when drilling through the Dammam, Hartha, and Shuaiba formations. Drilling engineers are challenged to select the optimum value for key drilling parameters such as ECD, Yp, MW, WOB, ROP, and RPM to mitigate mud losses in these formations. Many of these drilling parameters are inter-related and the overall impact of changing key parameters require extensive drilling experience and study. A multi-regression analysis was performed on mud loss event data for more than 300 wells drilled in Basra's oil fields. From this analysis, a model was developed to predict …

Bio-Inspired Geomaterial Improvement And Development Of Innovative Characterization Methods, Junnan Cao

Doctoral Dissertations

"This study experimentally investigated the bio-inspired improvement on geomaterials, including enzyme induced calcite precipitation (EICP) and biopolymers. This study also developed several innovative characterization tools to advance the state-of-the-art testing techniques, including SIP-BE column, rotational sedimental panel, and backpressure saturated constant hydraulic gradient break through column. Firstly, EICP test was performed on Ottawa 50-70 sand in a newly developed SIP-BE column. Nondestructive techniques -- spectral induced polarization (SIP) and bender element were used to monitor the precipitation process and shear wave velocities (V_s). SIP, V_s, and SEM results all suggest contact cementation as the preferential precipitation …

Advanced Topologies Of High-Voltage-Gain Dc-Dc Boost Converters For Renewable Energy Applications, Ahmad Alzahrani

Doctoral Dissertations

This dissertation proposes several advanced power electronic converters that are suitable for integrating low-voltage dc input sources, such as photovoltaic (PV) solar panels, to a high voltage dc bus in a 200 - 960 V dc distribution system. The proposed converters operate in the continuous conduction mode (CCM) and offer desirable features such as low-voltage stresses on components, continuous input currents, and the ability to integrate several independent dc input sources. First, a family of scalable interleaved boost converters with voltage multiplier cells (VMC) is introduced. Several possible combinations of Dickson and Cockcroft-Walton VMCs are demonstrated and compared in terms …

Sensitivity Of Rheological Properties Of Cement Paste With Scc Consistency, Azadehalsadat A. Asghari

Doctoral Dissertations

"Robustness, which is defined as the capacity of a mixture to tolerate small variations in constituent elements, mixing parameters or temperature that are inevitable with production at any significant scale, is a key property to expand the practical implementation of self-consolidating concrete (SCC). At the first step, the effect of different amount of water, amount of superplastizer, mixing time, mixing speed and the addition time of superplastizer on the rheological properties of cement pastes with SCC consistency, has been evaluated. Two different SCC mix design concepts, the powder-type and VMA-type were selected for this research. The results show that the …

Design And Development Of A Compact X-Ray Tube For Stationary Ct Architecture, Ashish Vighnahar Avachat

Doctoral Dissertations

"Multisource architectures enable sweeping one or more x-ray beams across the imaging field-of-view faster than physically moving a single x-ray source and/or a detector. Hence, these architectures are attractive for the applications in which temporal resolution plays an important role, for example, cardiac computed tomography (CT) or real-time CT. One of the recent developments in multisource architectures for CT imaging is stationary CT architecture, whereby two separate stationary arrays -- one for x-ray sources and one for detectors -- are utilized to sweep one or more x-ray beams along the gantry and acquire 360 degree projections. To have a stationary …

Electrodeposited Epitaxial Cobalt Oxides And Copper Metal, Caleb M. Hull

Doctoral Dissertations

"Electrochemical deposition methods are presented for the deposition of Co(OH)₂ and Cu metal. Paper I shows the deposition of β-Co(OH)₂ on Ti through electrochemical reduction of [Co(en)₃]³⁺ to [Co(en)₃]²⁺ in 2M NaOH. The catalytic properties of the deposited Co(OH)₂ towards water oxidation is found comparable to Co₃O₄, with the surface of the Co(OH)₂ converting to CoOOH during the reaction. Paper II gives the conditions suitable for epitaxial growth of Co(OH)₂ on Au(100), Au(110), and Au(111) following the same reduction mechanism as described in Paper I. …

Modeling And Experimental Investigations On Particle Dynamic Behaviors In Laser 3d Printing With Blown Powder, Wei Li

Doctoral Dissertations

"Pre-mixed powder is frequently-used powder supply to fabricate Functional Gradient Material (FGM) by Laser 3D printing, which is also called Laser Metal Deposition (LMD). The deposited FGM composition is expected to be similar or same as supplied powder mixture. However, because pre-mixed powder has different particle densities and particle sizes, the caused particle acceleration differences can result in the separation in powder mixture. Up to now, there was no study focused on pre-mixed powders' flow behavior in LMD. The current research aims to investigate the flow behaviors of pre-mixed powder supplied for LMD through both experimental and modeling approaches. In …

Empirical Correlations Between Rock Cutting Parameters And Excavated Rock Surface Rebound Hardness, Azupuri Germanus Ayerikujei Kaba

Doctoral Dissertations

"In field excavation, cutting tools operate on rock surfaces damaged from previous tool pass, yet, average intact rock properties are often used in field project estimations. This can result in overestimation of excavation time and cost. The ability to accurately correlate the damaged rock properties to the excavation parameters means more reliable estimates of project completion time and costs, and hence improved the application of mechanical excavation technology to a wider range of civil and mining industries.

The purpose of this research was to better understand the relationship between rock cutting parameters and the excavated rock surface hardness during mechanical …

Multitarget Tracking And Terrain-Aided Navigation Using Square-Root Consider Filters, James Samuel Mccabe

Doctoral Dissertations

"Filtering is a term used to describe methods that estimate the values of partially observed states, such as the position, velocity, and attitude of a vehicle, using current observations that are corrupted due to various sources, such as measurement noise, transmission dropouts, and spurious information. The study of filtering has been an active focus of research for decades, and the resulting filters have been the cornerstone of many of humankind's greatest technological achievements. However, these achievements are enabled principally by the use of specialized techniques that seek to, in some way, combat the negative impacts that processor roundoff and truncation …

Characterization Of The Cylinderical Split Internal-Loop Photobioreactor With Scenedesmus Microalgae: Advanced Culturing, Modeling, And Hydrodynamics, Laith S. Sabri

Doctoral Dissertations

"Microalgae are fast growing photoynthetic microorganisms and it have very wide range of industrial applications such as biofuels and wastewater treatment. These cells can be grown in a wide variety of systems ranging from open culture systems (e.g., ponds) to closed culture systems of photobioreactor (e.g., airlift). The open culture systems exist in the external environment, and hence, are not intrinsically controllable. However, the microalgae production in enclosed photobioreactors faces prohibitively high production costs with special difficulty in reactor design and scale-up. The light availability and utilization efficiency in the photobioreactor in terms of design and scale-up consider as the …

Correlation Between Delay Time And Measured Concentration And Concentration Uncertainty By Neutron Activation Analysis, James Thomas Seman

Doctoral Dissertations

"For the last several decades, it has been apparent that new methods of identifying explosives can help investigators trace their origins. One way to identify an explosive is through the use of taggants: materials added to a product that encodes information about the product such as when it was manufactured.

This research investigates the survivability of a new identification taggant called the Nuclear Barcode that overcomes some of the downfalls that have been identified in prior taggants. The Nuclear Barcode encodes information as a unique combination of concentrations of rare earths (Ho, Eu, Sm, Lu, and Dy) and precious metals …

Discrete Element And Artificial Intelligence Modeling Of Rock Properties And Formation Failure In Advance Of Shovel Excavation, Muhammad Waqas

Doctoral Dissertations

"Rock tests are performed before the start of every mining or civil engineering project as part of a detailed feasibility study. The feasibility study is costly and it comprises drilling, sample collection, sample handling and laboratory testing. Numerical modeling techniques, such as Particle Flow Code (PFC), can be used to provide reliable estimates of rock strength values. The numerical models for unconfined compressive strength (UCS), direct tension, and Brazilian tests were developed in PFC, and validated using data from literature. A particle size range of 3-5 mm with D_max/D_min = 1.67 gave the best results. The numerical …

Signal Processing For Microwave Imaging Systems With Very Sparse Array, Xiahan Yang

Doctoral Dissertations

"This dissertation investigates image reconstruction algorithms for near-field, two dimensional (2D) synthetic aperture radar (SAR) using compressed sensing (CS) based methods. In conventional SAR imaging systems, acquiring higher-quality images requires longer measuring time and/or more elements in an antenna array. Millimeter wave imaging systems using evenly-spaced antenna arrays also have spatial resolution constraints due to the large size of the antennas. This dissertation applies the CS principle to a bistatic antenna array that consists of separate transmitter and receiver subarrays very sparsely and non-uniformly distributed on a 2D plane. One pair of transmitter and receiver elements is turned on at …

Dragline Excavation Simulation, Real-Time Terrain Recognition And Object Detection, Godfred Somua-Gyimah

Doctoral Dissertations

"The contribution of coal to global energy is expected to remain above 30% through 2030. Draglines are the preferred excavation equipment in most surface coal mines. Recently, studies toward dragline excavation efficiency have focused on two specific areas. The first area is dragline bucket studies, where the goal is to develop new designs which perform better than conventional buckets. Drawbacks in the current approach include operator inconsistencies and the inability to physically test every proposed design. Previous simulation models used Distinct Element Methods (DEM) but they over-predict excavation forces by 300% to 500%. In this study, a DEM-based simulation model …

Direct Numerical Simulation Of Pressure Fluctuations Induced By Supersonic Turbulent Boundary Layers, Chao Zhang

Doctoral Dissertations

"Direct Numerical Simulations are used to generate a database of high-speed zero-pressure-gradient turbulent boundary layers developing spatially over a flat plate with nominal freestream Mach number ranging from 2:5 to 14 and wall-to-recovery temperature ranging from 0:18 to 1:0. The flow conditions of the DNS are representative of the operational conditions of the Purdue Mach 6 quiet tunnel, the Sandia Hypersonic Wind Tunnel at Mach 8, and the AEDC Hypervelocity Tunnel No. 9 at Mach 14. The DNS database is used to gauge the performance of compressibility transformations, including the classical Morkovin's scaling and strong Reynolds analogy as well as …

Hydrodynamics Related Performance Evaluation Of Upflow Moving Bed Hydrotreater Reactor (Mbr) Using Developed Experimental Methods And Cfd Simulation, Vineet Alexander

Doctoral Dissertations

"Upflow Moving Bed Hydrotreater (MBR) reactor is used for hydrotreating resid crude oil. It is a two-phase upflow reactor having a catalyst bed with conical bottom, and plena. At industrial conditions the reactor is not performing at its best and encountering issues such as hot spots, catalyst agglomeration inside the catalyst bed leading to frequent shutdown of the reactor. The root cause of these problems are linked to the improper hydrodynamics inside the catalyst bed. To investigate this, the industrial scale MBR is scaled down to a pilot scale and indicative and key hydrodynamic parameters are investigated using developed experimental …