Engineering Commons^™

An Overview Of The Usage Of Default Passwords, Brandon Knierem, Xiaolu Zhang, Philip Levine, Frank Breitinger, Ibrahim Baggili

Electrical & Computer Engineering and Computer Science Faculty Publications

The recent Mirai botnet attack demonstrated the danger of using default passwords and showed it is still a major problem. In this study we investigated several common applications and their password policies. Specifically, we analyzed if these applications: (1) have default passwords or (2) allow the user to set a weak password (i.e., they do not properly enforce a password policy). Our study shows that default passwords are still a significant problem: 61% of applications inspected initially used a default or blank password. When changing the password, 58% allowed a blank password, 35% allowed a weak password of 1 character.

An Evaluation Of The Groundwater Microbial Community's Toluene Biogenesis Potential At A Site In Southeast Louisiana, Michael A. Griffin Jr.

LSU Master's Theses

The broad goal of the research described in this thesis was to better understand the potential for biological toluene production to occur in groundwater at a Superfund Site located in southeast Louisiana. Previous literature reported that bacterial isolates under laboratory test conditions and undefined microbial communities in anaerobic sludge digesters and seasonally stratified lakes can produce toluene biogenically. Most of the research reported on this subject previously, however, has been on systems in Europe and little research has been reported previously on such phenomena in North America.

In the research described here, studies were conducted utilizing groundwater from a Superfund …

Biomedical Optics Scientific Community, Brian W. Pogue

Dartmouth Scholarship

The new Editor-in-Chief, Brian Pogue, gives an overview of the biomedical optics community.

Evaluation Of Well Designs To Improve Access To Safe And Clean Water In Rural Tanzania, Aminata Kilungo, Linda Powers, Nathan B. Arnold, Kelli Marie Whelan, Kurt Paterson, Dale Young

Michigan Tech Publications, Part 1

The objective of this study was to examine three well designs: drilled wells (20–30 m deep), closed dug wells (>5 m deep), and hand-dug open wells (<5 m deep), to determine the water quality for improving access to safe and clean water in rural communities. Heterotrophic plate count (HPC), total coliforms (TC), Escherichia coli (E. coli) and turbidity, were used to assess the water quality of 97 wells. Additionally, the study looked at the microflora diversity of the water, focusing on potential pathogens using outgrowth, PCR, and genome sequencing for 10 wells. Concentrations of TC for the open dug wells (4 × 10⁴ CFU/100 mL) were higher than the drilled (2 × 10³ CFU/100 mL) and closed dug wells (3 × 10³ CFU/100 mL). E. coli concentration for drilled and closed dug wells was <22 MPN (most probable number)/100 mL, but higher for open wells (>154 MPN/100 mL). The drilled well turbidity (11 NTU) was within the standard deviation of the closed well (28 NTU) compared to open dug wells (49 NTU). Drilled and closed wells had similar microbial diversity. There were no …

Electron Effective Mass In Sn-Doped Monoclinic Single Crystal B-Gallium Oxide Determined By Mid-Infrared Optical Hall Effect, Sean Knight, Alyssa Mock, Rafal Korlacki, Vanya Darakchieva, Bo Monemar, Yoshinao Kumagai, Ken Goto, Masataka Higashiwaki, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

The isotropic average conduction band minimum electron effective mass in Sn-doped monoclinic single crystal B-Ga₂O₃ is experimentally determined by the mid-infrared optical Hall effect to be (0.28460.013)m₀ combining investigations on (010) and (_201) surface cuts. This result falls within the broad range of values predicted by theoretical calculations for undoped B-Ga₂O₃. The result is also comparable to recent density functional calculations using the Gaussian-attenuation- Perdew-Burke-Ernzerhof hybrid density functional, which predict an average effective mass of 0.267m₀. Within our uncertainty limits, we detect no anisotropy for the electron effective mass, which …

Diversionary Behavior During Congestion, Venkata Vamsikrishna Peddisetty

LSU Master's Theses

Most people in the US prefer to travel on freeways, but when there is congestion they divert onto local routes to avoid travel delay. This study measures the traffic diversion induced by an increase in congestion on I-10 freeway in Baton Rouge during congestion, using a Bluetooth Detection System. The main objective of the study was to identify the difference in the level of congestion on the I-10 between the Mississippi River Bridge and the I-10/I-12 split and the level of congestion on local roads that triggers traffic to divert from the freeway to parallel arterials. Other objectives include measuring …

Investigation Into Reynolds Number Effects On A Biomimetic Flapping Wing, Daniel K. Hope, Anthony M. Deluca, Ryan P. O'Hara

Faculty Publications

This research investigated the behavior of a Manduca sexta inspired biomimetic wing as a function of Reynolds number by measuring the aerodynamic forces produced by varying the characteristic wing length and testing at air densities from atmospheric to near vacuum. A six degree of freedom balance was used to measure forces and moments, while high speed cameras were used to measure wing stroke angle. An in-house created graphical user interface was used to vary the voltage of the drive signal sent to the piezoelectric actuator which determined the wing stroke angle. The Air Force Institute of Technology baseline 50 mm …

College Of Engineering News, Georgia Southern University

College of Engineering & Computing: News & Publications (2010-2023)

• The New Allen E. Paulson College of Engineering & Computing

Interplay Of Molecular And Nanoscale Behaviors In Biological Soft Matter, Nicholas Ciaffone

Electronic Theses and Dissertations

The complexity of biological soft matter at the sub-micrometer level is fundamentally correlated to the functionalities at the larger scale. Reflecting the level of heterogeneities in the properties of systems remains challenging when probing small scales, due to the mismatch between the area surveyed with the tools offering nanoscale resolution, such as atomic force microscopy (AFM), and the scale of natural variations inherent to biology. Hence, to understand the physiological and mechanical alterations that occur within a single cell relative to a cell population, a multiscale approach is necessary. In this work we show that it is possible to observe …

Tunable Effect Of Metal Ions On Polyelectrolyte Mechanics, Angie Diaz

Electronic Theses and Dissertations

Polyelectrolyte based hydrogel fibers can mimic extracellular matrix and have applications such as drug delivery and tissue scaffolding. Metal ions play a critical role in hydrogel fiber stability via electrostatic interactions, but knowledge of how they modulate mechanical properties of individual polyelectrolyte polymers is lacking. In this study, electrospun polyacrylic acid with chitosan is used as a model system to evaluate ferric ion effect on nanofiber mechanics. Using dark field microscopy imaging and persistence length analysis, we demonstrate that ferric ions modulate the bending stiffness of nanofibers. Young's modulus of individual nanofibers is estimated at values of a few kilopascals, …

Low Cost Waist Line Circumference Health Management Belt, Raghav Talreja

Research Opportunities for Engineering Undergraduates (ROEU) Program 2017-18

One third of the American population is obese or near obese, and $150 billion is spent in weight management. Current devices to monitor weight are expensive, and niche products are designed for health enthusiasts. This project investigates user needs, development and commercialization steps for a low cost health management belt.

Preparation For The Study Of Gene Expression Aboard The International Space Station, Amber Paturzo

STAR Program Research Presentations

WetLab-2 performs quantitative polymerase chain reaction (qPCR) aboard the micro-gravity environment of the International Space Station in order to research how the stress of micro-gravity affects an organism’s RNA production and gene expression. This on-station qPCR allows researchers to gather information earlier and thereby allow them to modify experiments in a matter of hours rather than wait until the next flight opportunity. After a successful validation flight on SpaceX-8 and follow-up investigation on SpaceX-9, system components must now be adjusted for a new type of biological sample. Specifically, the WetLab-2 facility includes a commercial qPCR instrument (RNA SmartCycler), a sample …

Astrobee: Air Sampling Device And Zero Robotics Game, Bryce Van Ross

STAR Program Research Presentations

Astrobee is a free-flying, 1'x1'x1' cuboid robot that is planned to be onboard the International Space Station (ISS) by February 2019. Astrobee will be the successor of the current ISS free-flyer, SPHERES. Free-flying robots possess a range of potential. They can facilitate work for astronauts aboard the ISS by performing rudimentary tasks and housekeeping (e.g., record-keeping, sensor analysis, etc.) efficiently. Free-flyers also act as innovative testbeds for guest scientists to perform zero-gravity control theory research. In recent years, SPHERES has hosted annual Zero Robotics (ZR) programming competitions in collaboration with MIT, challenging middle and high school students to write code …

Scada System Maintenance: An Often Overlooked Necessity, Charles M. Burt, Kyle Fesit

BioResource and Agricultural Engineering

The design and implementation of a Supervisory Control and Data Acquisition (SCADA) system is typically undertaken by expert engineers and integration contractors. In order to provide a robust and reliable SCADA system, good design and installation practices are required. Preserving the initial SCADA system reliability requires good maintenance. Unfortunately, SCADA maintenance is often overlooked or underestimated. There are two potential providers for SCADA maintenance activities. Some SCADA maintenance activities are best provided by the developer or installer of the SCADA system, before closing out a project contract. Other SCADA maintenance requirements are best provided by the irrigation district or SCADA …

A New Approach To Vfd System Specifications And Rebates, Kyle Feist, Randall Cole, Charles M. Burt

BioResource and Agricultural Engineering

Variable frequency drives (VFDs) are used to provide flexibility and efficiency enhancements for agricultural pressurized irrigation systems. Standard 6-pulse VFDs commonly used for agricultural pumps can also create real problems with the pump motor and nearby electrical systems, unless mitigated by special equipment.

With support by the California Polytechnic State University (Cal Poly) Irrigation Training and Research Center (ITRC), Pacific Gas and Electric Company (PG&E) recently began a new rebate program for installing VFD systems for pressurized irrigation. A major component of the new rebate program is the requirement to comply with a detailed set of minimum VFD system design …

Size, Charge And Dose Dependent In-Vitro Kinetics Of Polystyrene Nanoparticles, Yasmine Abdellatif

Electronic Theses and Dissertations

The aim of the study described herein is to quantify the in-vitro kinetics of internalization of polystyrene nanoparticles (PS NPs) by cells. We used different charges, sizes and doses of fluorescently labelled PS NPs. Nanoparticles were characterized with UV-Vis, Fluorescence emission Dynamic Light Scattering (DLS) and Zeta potential for knowing their absorption, fluorescence spectra, size, charge, respectively. Additionally, cell viability was tested to know the toxicity of PS NPs. The quantitative uptake, the kinetics profile and rate of uptake were studied by using a new in-vitro fluorescence assay. This was achieved quantitatively and qualitatively by fluorescent plate reader and confocal …

2017-2018 Che Newsletter, Department Of Chemical Engineering, Michigan Technological University

Department of Chemical Engineering Newsletters

Table of Contents

• Department
• Convocation
• Student News
• Faculty
• Alumni & Friends

2018 Civil And Environmental Engineering Department News, Department Of Civil And Environmental Engineering, Michigan Technological University

Department of Civil, Environmental, and Geospatial Engineering Newsletters

Table of Contents

• External Awards
• Faculty Feature
• Student Features
• Outreach
• Alumni Feature
• CEE Academy
• Internal Awards
• Donors

Riverbank Filtration Impacts On Post Disinfection Water Quality In Small Systems—A Case Study From Auburn And Nebraska City, Nebraska, Matteo D'Alessio, Bruce Dvorak, Chittaranjan Ray

Nebraska Water Center: Faculty Publications

Small water systems can experience a fluctuating quality of water in the distribution system after disinfection. As chlorine is the most common disinfectant for small systems, the occurrence of disinfection byproducts (DBPs) represents a common problem for these systems. Riverbank filtration (RBF) can be a valuable solution for small communities located on riverbanks. The objectives of this study were to evaluate (i) the improvements in water quality at two selected RBF systems, and (ii) the potential lower concentrations of DBPs, in particular, trihalomethanes (THMs), in small systems that use RBF. Two small communities in Nebraska, Auburn and Nebraska City, using …

Flow Analysis Through Collector Well Laterals: A Case Study From Sonoma County Water Agency, California, Matteo D'Alessio, John Lucio, Ernest Williams, James Warner, Donald Seymour, Jay Jasperse, Chittaranjan Ray

Nebraska Water Center: Faculty Publications

The Sonoma County Water Agency (SWCA) uses six radial collector wells along the Russian River west of Santa Rosa, to provide water for several municipalities and water districts in north-western California. Three collector wells (1, 2, and 6) are located in the Wohler area, and three collector wells (3, 4, and 5) are located in the Mirabel area. The objective of this paper is to highlight the performance of the three collector wells located in the Mirabel area since their construction. The 2015 investigation showed a lower performance of Collectors 3 and 4 compared to their original performances after construction …

Benchmarking Environmental Efficiency Of Ports Using Data Mining And Rdea: The Case Of A U.S. Container Ports, Yong Shin Park, N. Muhammad Aslaam Mohamed Abdul Ghani, Fesseha Gebremikael, Gokhan Egilmez

Mechanical and Industrial Engineering Faculty Publications

This study provides step-wise benchmarking practices of each port to enhance the environmental performance using a joint application of the data-mining technique referred to as Kohonen’s self-organizing map (KSOM) and recursive data envelopment analysis (RDEA) to address the limitation of the conventional data envelopment analysis. A sample of 20 container ports in the U.S.A. were selected, and data on input variables (number of quay crane, acres, berth and depth) and output variables (number of calls, throughput and deadweight tonnage, and CO2 emissions) are used for data analysis. Among the selected samples, eight container ports are found to be environmentally inefficient. …

Flow Energy Harvesting Based On Oscillating Passively-Deforming Airfoils, Firas F. Siala

Link Foundation Energy Fellowship Reports

The rising global trend to reduce dependence on fossil fuels has provided significant motivation toward the development of alternative energy conversion methods and new technologies to improve their efficiency. Recently, the idea of using oscillating airfoils has been gaining a wider scope of attention as a means of extracting kinetic energy from streams, rivers, tidal flows and wind (Xiao & Zhu 2014). A large contribution to the existing knowledge has come through the studies of animal flight and swimming (Drucker & Lauder 1999; Triantafyllou et al. 2000; Sane 2003; Ho et al. 2003), where the oscillatory/flapping motion of wings or …

Rc Baja Car Drivetrain/Steering Assembly, Douglas Erickson

All Undergraduate Projects

ASME hosts an annual competition between students to test various abilities of RC Baja cars under certain restraints. To compete, two members must coordinate to manufacture a suitable RC Baja car according to the parameters set by ASME. The objective of this project is to design and manufacture the drivetrain and steering mechanism. The other teammate will concurrently design and manufacture the chassis and suspension assembly. The drivetrain consists of two main assemblies, the transmission and the differential. The transmission houses the initial gear reduction as well as the motor and is manufactured using ABS printed plastic. The differential mates …

Foundry Flask Punch-Out Machine, Nolan Stockman

All Undergraduate Projects

In the green sand molding process olivine sand is compacted into flasks that are used for the molding and pouring process in a foundry. These sands are difficult to remove after the pour has been made. In Central Washington University’s foundry the sands are currently being removed with handheld rams. To improve on this process a Foundry Flask Punch Out machine was designed. The machine was designed to utilize a wall mounted rack and pinion style press. The supporting elements of both the flask and press were engineered with deflection requirements in mind. The machine was made to fit into …

Rc Baja Car Suspension, Tyler Martin

All Undergraduate Projects

This year the Mechanical Engineering Technology Department at CWU is holding an R/C Baja car competition using the same rules as the ASME competition. The designed car must compete in three separate events: the slalom course, drag race, and obstacle course. By not only completing, but also being competitive in each of the events, the car will be deemed a success. Suspension and steering are two essential components of any R/C car, and was the main focus for this report. The suspension must be able to support the car in the event of impacts. In addition, the steering must be …

Pressure Regulator For A High-Altitude Balloon, Kala Brown

All Undergraduate Projects

High altitude balloons are large latex balloons filled with gas that carry payloads to near space. They provide a convenient way to study the Earth’s atmosphere. Per Boyle’s Law, the pressure and volume of a confined gas are inversely proportional. Thus, as the balloon ascends and the atmospheric pressure decreases, the gas inside the balloon expands. This pressure difference allows the balloon to ascend, but it also causes it to continuously expand until it bursts. For some observations, one might want their balloon to remain at constant altitude for a period of time. One way to achieve this is to …

Senior Project Hauff Tree Pruner, Brian Woolery

All Undergraduate Projects

Neil Hauff, a business owner and entrepreneur from the Yakima valley challenged a team of engineering students from Central Washington University to design a motorized apple tree pruner. This report will discuss the engineering and construction that went into creating the housing of the tree pruner. The housing component needed to be able to protect the moving parts of the pruner, while withstanding the rotational torque produced by the Makita power drill used to drive the pruner. The biggest constraint in designing the housing was to keep the weight of the housing component under 1.5 lbs, while still keeping the …

Repurposing Carbon Fiber Composite Through Mechanical Means, Jason Morrow

All Undergraduate Projects

Composite waste from the 777 aircraft is a growing concern for Boeing and amounts to an excess of 600,000 pounds of highly valuable carbon fiber being thrown away. Reclaiming this material has been a long sought-after goal of Boeings as the current solution is ever expanding landfills. The two current methods of recycling composite waste are chemically and mechanically processing. The focus of this paper will be demonstrating the feasibility of mechanically processing composite waste to increase storage efficiency before chemically treating to reclaim the actual carbon fibers. This paper provides a two-stage solution for the recycling question. The first …

Yz250 Lhrb, Ethan Di Loreto

All Undergraduate Projects

YZ250 LHRB

A Left Hand Rear Brake (LHRB) means that a motorcycle can not only have the rear brake operated by the foot pedal that comes standard on all bikes, but it can be actuated by a lever located on the handlebar as well. The purpose of this engineering project is to design a bracket that can hold two brake calipers while not hindering stock handling. It should also add braking usability and power.

The device is to be made of mild steel for the first models, this will allow for ease of prototyping, fitment testing, and finalized design testing. …

Plastic Injection Mold, Ryan Heaton

All Undergraduate Projects

The engineering department at Central Washington University is equip with three different plastic injection presses. Two of which are not being used because of various reasons, one being a lack of quality molds. This project’s purpose was to design and fabricate a quality mold that could be used in one of the injection presses as a teaching aid. The design for this project is based off of existing molds that are currently being used in the plastic injection industry along with many analyses such as; calculating speeds and feeds for machining, calculating tolerances, material strength, and a material’s heat conduction …