Engineering Commons^™

Marine Boundary Layer Aerosol In The Eastern North Atlantic: Seasonal Variations And Key Controlling Processes, Guangjie Zheng, Yang Wang, For Full List Of Authors, See Publisher's Website.

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The response of marine low cloud systems to changes in aerosol concentration represents one of the largest uncertainties in climate simulations. Major contributions to this uncertainty are derived from poor understanding of aerosol under natural conditions and the perturbation by anthropogenic emissions. The eastern North Atlantic (ENA) is a region of persistent but diverse marine boundary layer (MBL) clouds, whose albedo and precipitation are highly susceptible to perturbations in aerosol properties. In this study, we examine MBL aerosol properties, trace gas mixing ratios, and meteorological parameters measured at the Atmospheric Radiation Measurement Climate Research Facility's ENA site on Graciosa Island, …

Developing A Non-Cooperative Optimization Model For Water And Crop Area Allocation Based On Leader-Follower Game, Abbas Sedghamiz, Mohammad Reza Nikoo, Manouchehr Heidarpour, Mojtaba Sadegh

Civil Engineering Faculty Publications and Presentations

In this paper, a mathematical model for conflict resolution among a diverse set of agricultural water users in Golestan province, Iran, is developed. Given the bi-level nature of the distribution of power in the current problem, a combination of Leader–Follower game and Nash–Harsanyi bargaining solution method is employed to find optimal water and crop area allocations. The Golestan Regional Water Authority is the leader in this setting, controlling the total water allocations; and the agricultural sectors are the followers, competing over the allocated water. Two objectives for the leader are (i) maximizing profits, and (ii) maximizing share of green water …

A New Normal For Streamflow In California In A Warming Climate: Wetter Wet Seasons And Drier Dry Seasons, Iman Mallakpour, Mojtaba Sadegh, Amir Aghakouchak

Civil Engineering Faculty Publications and Presentations

In this study, we investigate changes in future streamflows in California using bias-corrected and routed streamflows derived from global climate model (GCM) simulations under representative concentration pathways (RCPs): RCP4.5 and RCP8.5. Unlike previous studies that have focused mainly on the mean streamflow, annual maxima or seasonality, we focus on projected changes across the distribution of streamflow and the underlying causes. We report opposing trends in the two tails of the future streamflow simulations: lower low flows and higher high flows with no change in the overall mean of future flows relative to the historical baseline (statistically significant at 0.05 level). …

Optimization And Validation Of Efficient Models For Predicting Polythiophene Self-Assembly, Evan D. Miller, Matthew L. Jones, Michael M. Henry, Paul Chery, Kyle Miller, Eric Jankowski

Materials Science and Engineering Faculty Publications and Presentations

We develop an optimized force-field for poly(3-hexylthiophene) (P3HT) and demonstrate its utility for predicting thermodynamic self-assembly. In particular, we consider short oligomer chains, model electrostatics and solvent implicitly, and coarsely model solvent evaporation. We quantify the performance of our model to determine what the optimal system sizes are for exploring self-assembly at combinations of state variables. We perform molecular dynamics simulations to predict the self-assembly of P3HT at ~350 combinations of temperature and solvent quality. Our structural calculations predict that the highest degrees of order are obtained with good solvents just below the melting temperature. We find our model produces …

A Survey Of Virtual Network Architectures, Lenoy Avidan

Computer Science and Software Engineering

With the storage needs of the world increasing, especially with the growth of cloud computing, data centers are being utilized more than ever. The increasing need of storage has led to more use of virtualization to help intra and inter data center communications. The virtualization of physical networks is used to help achieve this goal, but with the creation of Virtual Networks, systems must be designed to create, manage, and secure them. A Virtual Network Architecture is the system design for creating and maintaining virtual network components and the resulting networks they create. Different companies design different Virtual Network Architectures, …

Blokus Game Solver, Chin Chao

Computer Engineering

Blokus (officially pronounced as “Block us”) is an abstract strategy board game with transparent Tetris-shaped, color pieces that players are trying to place onto the board. However, the players can only place a piece that touches at least one corner of their own pieces on the board. The ultimate goal of the game is to place as many pieces onto the board as a player can while blocking off the opponent’s ability to place more pieces onto the board. Each player has pieces with different shapes and sizes that can be placed onto the board, where each block within a …

Degradation Of 3-Nitro-1, 2, 4-Trizole-5-One (Nto) In Wastewater With Uv/H2o2 Oxidation, Amalia Terracciano, Christos Christodoulatos, Agamemnon Koutsospyros, Zhaoyu Zheng, Tsan-Liang Su, Benjamin Smolinski, Per Arienti, Xiaoguang Meng

Civil Engineering Faculty Publications

Insensitive Munition (IM) formulations contain 3-nitro-1,2,4-trizole-5-one (NTO), an energetic compound with the highest aqueous solubility (16 g L⁻¹) among all IM explosives, including 2,4-dinitroanisole (DNAN) and 1-nitroguanidine (NQ); as a result wastewater streams from IM processing facilities can be highly contaminated and potentially toxic. The removal of energetic compounds from wastewater streams prior to their discharge in the environment is imperative, and new technology must be developed to efficiently treat high levels of NTO and other IM compounds in these streams. In this study, the treatment of NTO wastewater by a UV/H₂O₂ oxidation process under …

A New Computational Intelligence Approach To Predicting The Machined Surface Roughness In Metal Machining, Ning Fang, P. Srinivasa Pai

Engineering Education Faculty Publications

Machined surface roughness is an important parameter used in the evaluation of the surface integrity of machined parts and components. This paper proposes a new computational intelligence approach to predicting the machined surface roughness in metal machining. In this approach, wavelet packet transform (WPT) is incorporated into artificial neural networks (ANN) to develop two ANN models for predicting average roughness Ra and root-mean-square roughness Rq, respectively. Each model has eight inputs, including the cutting speed, the feed rate, energy of wavelet packets for three cutting force components, and energy of wavelet packets for three cutting vibration components. Forty-five machining experiments …

Fingerprint Database Privacy Guard: An Open-Source System That Secures Fingerprints With Locality Sensitive Hashing Algorithms, Enrique Sanchez

Computer Science and Computer Engineering Undergraduate Honors Theses

Fingerprint identification is one of the most accurate sources of identification, yet it is not widely used in public facilities for security concerns. Moreover, the cost of fingerprint system is inaccessible for small-budget business because of their high cost. Therefore, this study created an open-source solution to secure fingerprint samples in the database while using low-cost hardware components. Locality Sensitive Hashing Algorithms such as ORB and Image hash were compared in this study as a potential alternative to SURF. To test the design, fifteen samples were collected and stored in a database without verifying the quality of the samples. Then, …

Young’S Modulus As A Measurement To Estimate Damage Related With Alkali-Silica Reaction In Concrete., Anazaria J. Ortega Gonzalez

Civil Engineering Undergraduate Honors Theses

The main purpose of this research is to compare two nondestructive methods to assess Alkali-Silica reaction (ASR) in concrete. Fifteen concrete prisms were cast using aggregates with different Alkali-Silica reactivity such as Jobe sand and Van Buren sand. The change in strain, shear wave velocity and Young’s modulus were determined according to ASTM C129 and ASTM C215, respectively. This data was collected by Dillon K Self, who determined that the shear wave velocity and strain are inversely proportional. However, when single cracking in the concrete specimen transition to map cracking, the shear wave velocity dropped significantly, whereas the strain value …

Inspire E-News 12 2018, College Of Engineering And Applied Sciences

College of Engineering and Applied Sciences News

• Holiday greetings from the Dean
• Simulating flight
• Join us for Innovation EXPO
• Students attend Society of Women Engineers annual conference
• Last roll
• Ph.D. student joins board of industrial engineering institute
• College Snapshot: Industrial and Entrepreneurial

Fiber Element-Based Nonlinear Analysis Of Concrete Bridge Piers With Consideration Of Permanent Displacement, Mokhtar Ansari, Farhad Daneshjoo, Amir Safiey, Naser Safaeian Hamzehkolaei, Maryam Sorkhou

Publications

Utilization of fiber beam-column element has gained considerable attention in recent years due mainly to its ability to model distributed plasticity over the length of the element through a number of integration points. However, the relatively high sensitivity of the method to modeling parameters as well as material behavior models can pose a significant challenge. Residual drift is one of the seismic demands which is highly sensitive to modeling parameters and material behavior models. Permanent deformations play a prominent role in the post-earthquake evaluation of serviceability of bridges affected by a near- fault ground shaking. In this research, the influence …

Understanding Track Substructure Behavior: Field Instrumentation Data Analysis And Development Of Numerical Models, Huseyin Boler, Debakanta Mishra, Wenting Hou, Erol Tutumluer

Civil Engineering Faculty Publications and Presentations

Numerous studies have targeted using numerical modeling, field instrumentation, or combinations of both to gain insight into track substructure behavior under loading. In-depth understanding of track substructure behavior serving both passenger and freight trains is critical to developing suitable design and maintenance/rehabilitation methods to ensure adequate performance under loading. This manuscript presents findings from a recently completed study involving advanced instrumentation and numerical modeling to investigate track substructure-related issues at several problematic railroad bridge approaches in the United States. Multi-Depth Deflectometers (MDDs) were installed to measure transient as well as plastic deformations experienced by track substructure layers under loading. Strain …

Foam Materials With Controllable Pore Structure Prepared From Nanofibrillated Cellulose With Addition Of Alcohols, Jinbao Li, Te Song, Huijuan Xiu, Meiyun Zhang, Rui Cheng, Qiang Liu, Xuefei Zhang, Evguenii Kozliak, Yun Ji

Chemical Engineering Faculty Publications

Low-density foams based on nanofibrillated cellulose (NFC) made from Pinus massonianesoftwood pulp were prepared from NFC aqueous suspensions containing one of four C2–C4alcohols followed by freeze-drying, with the goal of controlling their pore structure and reducing the shrink rate. The foams prepared from NFC suspensions containing ethanol, isopropanol and n-butanol exhibited highly porous structures with a honeycomb-like cellular texture featuring well-defined “cell walls” between the layers. By contrast, the tert-butanol/NFC foam featured a higher number of smaller size pores with irregular shape. The foams prepared by freezing at −196 °C with ethanol also revealed small size pores, with no layered …

Development Of Anti-Icing Airfield Heated Pavement Systems Using Solar Energy, Joseph Daniels

Graduate Theses and Dissertations

This dissertation analyzes developing and assessing the viability of an anti-icing airfield heated pavement system using solar energy. This study includes two components, a field experimentation component and a numerical analysis component. Field experimentation investigates two systems: (1) an electrical heated pavement system with a photovoltaic energy system as its power source, and (2) a hydronic heated pavement system with a solar water-heating system as its heating source. The systems operate under an automated thermostat heating sequence for operation optimization and energy conservation. Study results found the solar systems capable of supplying enough energy to maintain pavement surface temperature above …

Utilizing The Hvsr Second Peak For Surface Wave Inversions In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

Ambient noise data from 24 sites within the Mississippi Embayment were analyzed to estimate the fundamental frequency using the horizontal to vertical spectral ratio (HVSR) method. The fundamental frequency ranged from 0.17 to 3.43 Hz for the tested sites. At seventeen of the sites, a second higher frequency HVSR peak, which ranged from 0.617 Hz to 2.154 Hz, was observed in addition to the fundamental HVSR peak. The second peak frequency in the HVSR curve has been attributed by previous researchers as either an odd harmonic of the fundamental peak or a shallow impedance contrast from the Memphis sand layer …

Early Life Flexural Performance And Behavior Of Reinforced Bcsa Concrete Beams, Gabriel Cook

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate cement (BCSA) is a hydraulic, rapid setting alternative to ordinary portland cement (OPC) with reduced energy demands and CO2 emissions. BCSA cement has numerous current and potential applications including transportation repair and precast manufacturing. Currently, limited research exists regarding the structural performance of CSA cements, restricting its potential implementation. Thus, the purpose of this research is to provide insight into the flexural performance and behavior of reinforced BCSA concrete beams. Overall, BCSA concrete had similar cracking and loading behavior to the OPC beams, with increased moment capacity for compression controlled specimens. Furthermore, BCSA concrete showed increased tensile …

Interfacial Tailoring Of Lithium-Ion Batteries By Atomic/Molecular Layer Deposition, Qian Sun

Graduate Theses and Dissertations

Lithium-ion batteries (LIBs) are promising energy storage devices, which play significant roles in addressing problems related to fossil fuels depletion and environmental pollution. Since the 1990s, LIBs have attracted great attention for many applications. Nowadays, LIBs are dominating portable electronics, having several advantages over their forerunners, such as high voltage (3.3~4.2 V) [1,2], low self-discharge (< 5~10 %/month) [3,4], wide operation temperature (-20~60 °C) [5,6], and fast charge/discharge rate [7,8]. However, LIBs deliver an energy density of 100-220 Wh/kg in practice to date, which is far from their theoretical ones, thus hindering their further applications in electric vehicles. Additionally, LIBs have been plagued by other problems, such as intolerance to overcharge/overdischarge, low heat resistance, lithium dendrites growth, large volume change of the silicon anode, large polarization and even safety problems.

Atomic layer deposition (ALD) and molecular layer deposition (MLD) are two important techniques, both proceeding in self-limiting gas-solid reactions and exhibiting excellent capabilities for ultra-thin films, conformal coatings, and controllable growth. They can be employed to address the problems of LIBs mentioned above by …

Examining The Use Of Idealized Granular Material In Validated Dem Simulations, Anjana Thoroppady Kittu

Graduate Theses and Dissertations

Discrete element method (DEM) modeling, is becoming widely used for understanding the micro-mechanical behavior of granular materials at the particle level. This dissertation presents important considerations regarding the experimental boundary conditions and idealized granular materials used in DEM validations.

A common issue in DEM validation studies for direct shear and direct simple shear is selecting top and bottom cap boundary conditions that allow for shear transmission while also being efficiently modeled in the DEM simulations. While the traditional grid boundary types used in the laboratory can be replicated in the numerical models, researchers have also used fixed-particle boundaries, sawtooth boundaries, …

A Generative Statistical Approach For Data Classification In A Biologically Inspired Design Tool, Marvin Manuel Arroyo Rujano

Graduate Theses and Dissertations

The objective of the research this thesis describes is to find a way to classify text-based descriptions of biological adaption to support Biologically Inspired design. Biologically inspired design is a fairly new field with ongoing research. There are different tools to assist designers and biologists in bio-inspired design. Some of the most common are BioTRIZ and AskNature. In recent years, more tools have been proposed to aid and make research in the field easier, for example, the Biologically Inspired Adaptive System Design (BIASD) tool. This tool was designed with the goal of helping designers in early design stages generate more …

Fatigue Performance And Shear Demand Distributions Of Clustered Shear Connectors In Composite Bridge Girders, Brian David Hillhouse

Graduate Theses and Dissertations

The current American Association of State Highway and Transportation Officials (AASHTO) Bridge Specifications assumes uniform shear flow demands at the steel-concrete interface of composite bridge girders. As stud pitch increases to beyond 24 in or as studs become clustered to account for pre-cast concrete decks, this assumed shear demand distribution may be unrepresentative. Understanding shear transfer and resulting demands on headed studs in composite beams are important for ensuring adequate composite design. This study investigates stud demands in composite bridge girders using large-scale fatigue testing and direct pressure measurements for stud force calculations. In this study, two large-scale composite beam …

Accumulation Of Lead By Biofilms In Drinking Water Distribution Systems, Kaleb Oren Belcher

Graduate Theses and Dissertations

Recent crises, such as the one in Flint, MI, indicate that lead exposure from drinking water is a major health concern in the United States. Over six million lead service lines are still in use in the United States, and a universal protocol to safely remove these lead service lines from drinking water distribution systems has not yet been established. This paper calls to attention the potential hazard that biofilms pose as a source of lead in distribution systems, even after the removal of lead pipes. This study used a simulated water distribution system containing a lead source pipe and …

The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley

Graduate Theses and Dissertations

In the realm of additive manufacturing there is an increasing trend among makers to create designs that allow for end-users to alter them prior to printing an artifact. Online design repositories have tools that facilitate the creation of such artifacts. There are currently no rules for how to create a good customizable design or a way to measure the degree of customization within a design. This work defines three types of customizations found in additive manufacturing and presents three metrics to measure the degree of customization within designs based on the three types of customization. The goal of this work …

Developing Computer Codes For Analyzing Bridge Response Due To Wim Data Truck Loading, Kenneth Patrick Pasley

Graduate Theses and Dissertations

Despite actual truck demographics evolving over the past 30 years, the Arkansas legal loads for bridge posting have not been updated. Custom computer codes were developed.to facilitate comparison between the current Arkansas legal loads for bridge posting and the actual Arkansas truck traffic to ensure that actual reactions are enveloped by the state'. The program, WIMFluence, calculates shear and moment influence lines for a bridge and the resulting shear and moment reactions based on weigh-in-motion data. With supporting scripts, the reactions due to actual Arkansas truck traffic were compared to those due to the current Arkansas legal loads for bridge …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

On The Development Of 8,000 Psi Geopolymer Mortar For Practical Use In Field Applications, Remington Gabriel Reed

Graduate Theses and Dissertations

Although there are several perceived benefits from the use of geopolymer binder as an alternative to ordinary portland cement in concrete materials, it is not widely used in field applications. Geopolymer materials have no set guidelines for mixture design and often require heat curing to facilitate strength gain. Additionally, many geopolymers are created using carefully controlled and high quality materials and activator chemicals. These factors greatly affect the practicality of the material. The goal of this research was to create a geopolymer material capable of achieving high compressive strengths at 28 days without heat curing, and using only readily available …

Developing Ultra-High Performance Concrete (Uhpc) With Locally Available Materials, Ali Alsalman

Graduate Theses and Dissertations

Ultra-High Performance Concrete (UHPC) can enhance the durability and resilience of concrete structures. The use of local materials is a fundamental step to save energy and reduce the cost of concrete. The main focus of this research was to develop a UHPC with compressive strength of 150 MPa using locally sources materials. In this study, the effect of fine materials, binder type and content, type of mixer, steel fibers and curing regimes on concrete’s compressive strength were investigated. The relationship between compressive strength and elastic modulus was also studied. This study synthesizes all relevant experimental data in the literature to …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …

Effect Of Continuity Plate Eccentricity On The Performance Of Welded Beam-To-Column Connections, Jason Thomas Norwood

Graduate Theses and Dissertations

Beam-to-column connections in structural steel buildings may have varying degrees of rotational restraint and varying degrees of moment transfer. In fully restrained moment connections, shear is typically transferred through the beam web, while the moment is mostly transferred through the beam flanges which create tension/compression force couples. Column sections that are incapable of resisting these flange forces are often retrofitted with continuity plates within the connection region to improve capacity. In cases of unequal beam depths on either side of the column, an eccentricity between the framed-in beam flange and continuity plate may be required; however, limited research exists to …

Effect Of Cement Content On Concrete Performance, Caleb Joshua Lebow

Graduate Theses and Dissertations

Of all the traditional concrete materials, portland cement has the greatest impact on mixture cost and the environment. Cement is in many ways the glue holding concrete together (Weiss, 1999), and as such, it plays a major role in fresh and hardened concrete properties. Without the proper range of cement in the mixture, low strength development or excessive shrinkage may occur leading to premature deterioration. The Arkansas Department of Transportation (ARDOT) recognizes two types of concrete for use in bridge construction, Class S and Class S(AE). This paper focuses on the findings from testing of Class S(AE) concrete, short for …