Engineering Commons^™

A Control Algorithm For The Solar Village Microgrid System, Hamad Ahmed Alharkan

Masters Theses

"In this thesis, the concept of microgrid system is introduced. Also, the major components of a microgrid will be discussed thoroughly. Both grid-connected and autonomous modes are explained. In addition, the control of a microgrid is defined for the following types: local, centralized and decentralized control.

As one of the nation's premiere research universities, the Missouri University of Science and Technology has built four inspirational solar houses (solar villages) for a competition in the US Department of Energy Solar Decathlon to allow students to research and improve different aspects of the microgrid system. Consequently, this thesis develops a computer model …

Prediction Of Surface Roughness In Abrasive Waterjet Cutting Of Graphite Composite Using Response Surface Methodology, Prabhakar Bala

Masters Theses

"In the present work, surface roughness after machining of composite material was the main focus of study. Response surface methodology with Box- Behnken experimental design was applied in predicting the surface roughness (R_a) of abrasive waterjet cut 1-inch-thick graphite/epoxy composite. Second order response equations for R_a were generated with minitab, a statistical software as a function of pressure, traverse speed and isolated abrasive mesh size. Influence of each of these factors on the response were analyzed with 3D response surface plots. Abrasive mesh size was also found be a factor influencing Ra along with traverse speed and …

Shale Instability Of Deviated Wellbores In Southern Iraqi Fields, Ahmed Ali Shanshool Alsubaih

Masters Theses

"Wellbore instability problems are the cause for the majority of nonproductive time in the southern Iraqi fields' developments. The most severe problem in terms of effort and disbursement which is referred to a pipe sticking in Tanuma shale formation. Examining the drilling data revealed that this phenomenon was mostly related to the shear failure of the wellbore. Thus, a geomechanical analysis and drilling parameters/ practice optimization analysis were performed on a field in southern Iraq based on data from 45 deviated wells. The geomechanics analysis predicted the suitable drilling fluid density to prevent onset shear failure by using the Mogi-Coulomb …

Mixing Dynamics In Municipal Water Storage Tanks, Pramod Narayan Bangalore

Masters Theses

"The purpose of this study is to investigate the effects of different control variables on mixing in municipal water storage tanks using Computational Fluid Dynamics(CFD) solutions with ANSYS FLUENT for isothermal, positively and negatively buoyant inflow conditions. Poor mixing of old water and new water leads to dead zone formation, which when introduced in the distribution system can cause major water quality issues. Data for this study was generated using Multiphase CFD flow modeling technique using Volume of Fluid (VOF) approach with species transport. The vessel was considered to be mixed when Coefficient of Variation (COV) dropped below 0.10.

Results …

Attenuation Properties Of Cement Composites: Experimental Measurements And Monte Carlo Calculations, Raul Florez

Masters Theses

"Developing new cement based materials with excellent mechanical and attenuation properties is critically important for both medical and nuclear power industries. Concrete continues to be the primary choice material for the shielding of gamma and neutron radiation in facilities such as nuclear reactors, nuclear waste repositories, spent nuclear fuel pools, heavy particle radiotherapy rooms, particles accelerators, among others. The purpose of this research was to manufacture cement pastes modified with magnetite and samarium oxide and evaluate the feasibility of utilizing them for shielding of gamma and neutron radiation. Two different experiments were conducted to accomplish these goals. In the first …

Mechanistic Understanding Of Water-Rock Interactions During High-Salinity Water-Flooding Of Carbonate Reservoirs, Pu Han

Masters Theses

"Chemically tuned water-flooding provides a relatively cheap method of enhanced oil recovery from carbonate and sandstone reservoirs. Several possible recovery mechanisms such as mineral dissolution, multi-component ion exchange, double-layer expansion, adsorption/desorption from rock surface, reduction in interfacial tension, and fines migration that have been proposed are widely debated. The combination of these processes may result in wettability alteration that increases sweep efficiency of water-flooding. Here, wettability alteration due to water-rock interactions will be examined numerically.

To evaluate the wettability alteration, separation between breakthrough curves of the non-reactive component and the cations based on the chromatographic separation will be used due …

A Study On Non-Metallic Inclusions In Foundry Steel Process, Marc Leonard Harris

Masters Theses

"The effects of sample area and automated SEM/EDS feature analysis parameters (step size, magnification and threshold) on nonmetallic inclusion characterization results has been investigated and optimized. A post-processing program was developed to automatically determine average inclusion chemistry, total element concentrations within inclusions, and for generating joint ternary diagrams with size visualization for representing nonmetallic inclusion populations. Using these tools the evolution of nonmetallic inclusions was examined for 4320 steel at a participating industrial steel foundry. The steel was sampled throughout electric arc furnace melting through ladle refining to the final casting where an in-mold sampling procedure was developed to procure …

Hybrid Manufacturing Processes For Fusion Welding And Friction Stir Welding Of Aerospace Grade Aluminum Alloys, Megan Alexandra Gegesky

Masters Theses

"Friction stir welding and processing can provide for joints in aerospace grade aluminum alloys that have preferable material properties as compared to fusion welding techniques. Aerospace grade aluminum alloys such as AA2024-T3 and AA7075-T6 are considered non-weldable by traditional fusion welding techniques. Improved mechanical properties over previously used techniques are usually preferable for aerospace applications. Therefore, by combining traditional fusion welding and friction stir processing techniques, it could be plausible to create more difficult geometries in manufactured parts instead of using traditional techniques. While this combination of fusion welding and friction stir processing is not a new technology, its introduction …

Design Of A Microwave Imaging System For Rapid Wideband Imaging, Matthew Jared Horst

Masters Theses

An imaging system composed of two linear arrays of antennas is designed through full-wave simulation and fabricated for use in synthetic aperture radar imaging. The arrays electronically scan along their antenna elements and are mechanically moved along a second orthogonal direction for scanning large two-dimensional areas quickly. Each linear array is printed on a circuit board where the antenna elements are integrated into the edge of the board as tapered slot-line antennas operating at 22 to 27 GHz. A multiplexer circuit is printed onto each linear array to transmit wideband signals to each antenna in the array. Receivers are printed …

Mixed Metal Oxide Catalysts Supported On H-Beta For Hydrogenolysis Of Glycerol Into 1,3-Propanediol, Amit Kant

Masters Theses

"Bioglycerol is the by-product which is produced largely from the microbial fermentation, hydrogenolysis of glucose in the mixture of polyols, fatty ester, soap manufacturing process and fatty acid production. Hydrogenolysis of glycerol is one of the most promising ways to convert glycerol and many work has been done towards 1,3-propanediol, 1,2-propanediol and 1-propanol using various metals and mixed-metal oxides such as W, Ru, Rh, Pt, Pd, Cu, Ni and different zeolites have been extensively used as the active components.

It has been well documented that the presence of Bronsted acid sites leads to the formation of acrolein, while Lewis acid …

Influence Of Mix Design Parameters On Dynamic Segregation Of Self-Consolidating Concrete And Consequences On Performance Of Precast Beams, Aida Margarita Ley Hernandez

Masters Theses

"Self-Consolidating Concrete (SCC) is more vulnerable to stability problems as a consequence of its high flowing ability compared to conventional vibrated concrete. Dynamic segregation refers to the tendency of the concrete constituents to separate from the suspended matrix, usually in horizontal direction while being cast into the formwork or due to an impact. Similarly to static segregation, dynamic segregation can affect the homogeneity of SCC. Therefore, it is highly essential to ensure a proper dynamic stability in order to enhance the uniformity of in-situ properties of pre-stressed beams.

In this research project, the effects of SCC mix design parameters are …

Radiation Noise Source Modeling And Near-Field Coupling Estimation In Rf Interference, Liang Li

Masters Theses

"With increasing complexities and shrinking size of modern electronic devices, the near-field RF interference issues are becoming challenging for RF-digital mixed circuit design. Predicting the coupling from digital module to RF antennas and mitigating RF interference is important to the system performance. The ultimate goal of this study is to address the desensitization issues existing in modern electronic devices that have mixed high speed digital-RF circuits, such as cellphone and wearable devices.

In order to estimate the near-field noise coupling from digital module to RF antennas, the noise source is anticipated to be replaced by its equivalent radiation model which …

Thrust Sensing For Small Uavs, Christopher Scott Marchman

Masters Theses

"Unmanned aerial vehicles (UAVs) have become prevalent in both military and civilian applications. UAVs have many size categories from large-scale aircraft to micro air vehicles. The performance, health, and efficiency for UAVs of smaller sizes can be difficult to assess and few associated instrumentation systems have been developed. Thrust measurements on the ground can characterize systems especially when combined with simultaneous motor power measurements. This thesis demonstrates the use of strain measurements to measure the thrust produced by motor/propeller combinations for such small UAVs. A full-bridge Wheatstone circuit and electrical resistance strain gauges were used in conjunction with constant-stress cantilever …

Evaluating Completion Performance For Gas Wells In The Upper And The Lower Montney Formation, Canada, Omar Qasim Mohammed

Masters Theses

"Identifying the key drivers for success of multiple fractured horizontal wells is not straightforward, especially in unconventional reservoirs like the Montney. Al-Alwani et al. (2015) provided a statistical analysis of Montney completions based on publicly available data. They showed that for the entire well population, cumulative gas recovery per stage, declines as the number of completed stages increase. However, their statistical analysis did not differentiate between completions in the Upper/Middle/Lower Montney, and did not include perforation cluster data.

This work documents the statistical analysis of 296 cased-hole horizontal gas well completions reported in the Upper and the Lower Montney. The …

Developing An Idealistic Model To Characterize And Optimize A Photovoltaic Battery Systems, Pavani Reddy Nalladimmu

Masters Theses

"Solar energy is one of the most abundant and clean energy sources of renewable energy. Due to its unsteady nature, most photovoltaic systems require a solar storage system. Ultracapacitors have proven to be an effective solar energy storage component due to their wide range of input voltages and high power density. This research focuses on characterizing the performance of a PV/UCAP hybrid storage system to meet required household loads at various locations throughout the US as a backup energy source. A calibrated empirical model was developed to characterize system performance. A load profile was designed based on a typical 2 …

Deterministic Simulation Of Thermal Neutron Radiography And Tomography, Rajarshi Pal Chowdhury

Masters Theses

"In recent years, thermal neutron radiography and tomography have gained much attention as one of the nondestructive testing methods. However, the application of thermal neutron radiography and tomography hindered by their technical complexity, radiation shielding, and time-consuming data collection processes. Monte Carlo simulations have been developed in the past to improve the neutron imaging facility's ability. In this present work, a new deterministic simulation approach has been proposed and demonstrated to simulate neutron radiographs numerically using a ray tracing algorithm. This approach has made the simulation of neutron radiographs much faster than by previously used stochastic methods (i.e Monte Carlo …

Study Jitter Amplification Of A Passive Channel And Investigation Of S₂₁ Magnitude Extraction Methodologies Using A Pattern Generator And Oscilloscope, Xinyun Guo

Masters Theses

"Recently the clock channel jitter amplification has been observed in several publications. Currently in many high-speed I/O systems, to avoid the cost and the complex clock recovery circuit design, people use traces forwarding clock signal from transmitting IC to receiving IC. When these clock traces are long enough, the amount of attenuation will induce not only inter-symbol-interference (ISI) but also modulate with the input jitter. Eventually it will lead some type of jitter been amplified after the channel. Similarly, the high speed communication channel (data channel) will also face this issue. Since there are no studies on the jitter amplification …

Intensity Control Of Dielectric Barrier Discharge Filaments, Matthew Crawford Paliwoda

Masters Theses

"When operated in a filamentary mode, a volume dielectric barrier discharge (DBD) is known to produce patterned plasma structures. These structures are currently being explored for reconfigurable metamaterial applications. In this work the presence and intensity of a single filament, within an array of filaments, was controlled by adjusting the voltage to that filament's individual needle electrode. The current, voltage, and time-averaged normalized light intensity were measured while varying the voltage of the needle through a self-biasing resistance. For a 7.5 kV, 3.2 kHz DBD in air, the needle-controlled filament intensity varies from that of the surrounding filaments to zero …

Managing Risks Of Market Price Uncertainty For A Microgrid Operation, Sriram Raghavan

Masters Theses

"After deregulation of electricity in the United States, the day-ahead and real-time markets allow load serving entities and generation companies to bid and purchase/sell energy under the supervision of the independent system operator (ISO). The electricity market prices are inherently uncertain, and can be highly volatile. The main objective of this thesis is to hedge against the risk from the uncertainty of the market prices when purchasing/selling energy from/to the market. The energy manager can also schedule distributed generators (DGs) and storage of the microgrid to meet the demand, in addition to energy transactions from the market. The risk measure …

Carbon Transfer From Magnesia-Graphite Ladle Refractories To Ultra-Low Carbon Steel, Andrew Arthur Russo

Masters Theses

"Ultra-low carbon steels are utilized in processes which require maximum ductility. Increases in interstitial carbon lower the ductility of steel; therefore, it is important to examine possible sources of carbon. The refractory ladle lining is one such source. Ladle refractories often contain graphite for its desirable thermal shock and slag corrosion resistance. This graphite is a possible source of carbon increase in ultra-low carbon steels. The goal of this research is to understand and evaluate the mechanisms by which carbon transfers to ultra-low carbon steel from magnesia-graphite ladle refractory.

Laboratory dip tests were performed in a vacuum induction furnace under …

Characterization Of Fracture Initiation In Non-Cylindrical Buckle Folds Using 3d Finite Element Analysis, Eli Jacob Steinbeck

Masters Theses

"The spatial distribution of fracture sets associated with buckle folds has been well documented in field studies. There are difficulties, however, in placing accurate constraints on the timing of the initiation of individual fracture sets during the deformation history of the fold under in-situ conditions. This study investigates specific conditions that give rise to the initiation of various fracture sets in the hinge and limb of a pericline, based on an analysis of the effective stress evolution during the processes of buckling and erosional unloading. A 3D finite element modeling approach is used to simulate the effective stress evolution in …

Artificial Neural Network Approach To Predict Blast-Induced Ground Vibration, Airblast And Rock Fragmentation, Raymond Ninnang Tiile

Masters Theses

"Blasting has been widely used as an economical and cheap way of rock breakage in mining and civil engineering applications. An optimal blast yields the best fragmentation in a safe, economic and environmentally friendly manner. The degree of fragmentation is vital as it determines to a large extent the utilization of equipment, productivity and mill throughput. Explosive energy, besides rock fragmentation, creates health and safety issues such as ground vibration, air blast, fly rock, and back breaks among others. As a result, the explosive energy impacts structures and buildings located in the vicinity of the blasting operation, and causes human …

Composite Model Representation For Computer Aided Design Of Functionally Gradient Materials, Fangquan Wang

Masters Theses

"Functionally Gradient Materials (FGMs) feature smooth transition from one material to another within a single object. FGMs modeling is considered to be one of the new challenges in Computer Aided Design (CAD) area. To overcome this challenge, this thesis presents a composite approach to model FGMs. The input in STL format can be meshed and voxelized in FGMs modeling system. The material composition in each voxel can be generated from multiple different types of control features. And LTI filters including Gaussian Filter and Average Filter are applied to blur default material features in order to generate FGMs inside models. The …

De-Embedding Method For Electrical Response Extraction Of Through-Silicon Via (Tsv) In Silicon Interposer Technology And Signal Integrity Performance Comparison With Embedded Multi-Die Interconnect Bridge (Emib) Technology, Qian Wang

Masters Theses

"Traditional two-dimensional system-in-package (2D SiP) can no longer support the scaling of size, power, bandwidth, and cost at the same rate required by Moore's Law. Three-dimensional integrated circuits (3D-ICs), 2.5D silicon interposer technology in which through silicon vias are widely used, are implemented to meet these challenges. Embedded multi-die interconnect bridge (EMIB) technology are proposed as well.

In Section 1, a novel de-embedding method is proposed for TSV characterization by using a set of simple yet efficient test patterns. Full wave models and corresponding equivalent circuits are provided to explain the electrical performance of the test patterns clearly. Furthermore, broadband …

Engine Sound Simulation And Generation In Driving Simulator, Shuang Wu

Masters Theses

"Simulating a driving environment that provides engine sound as auditory feedback to the driver is a challenging task due to the complexity of engine sound, a wide range of operating speeds, and repeated sound clicking during playback. This thesis describes a method of engine sound simulation and generation for a driving simulator. By analyzing sample sounds, spectral modeling synthesis was used to decompose the sound samples into deterministic and stochastic components. Then, the modeled deterministic and stochastic signals were employed to resynthesize the sounds. To represent engine sounds not available in the recorded database, sound interpolation was applied to two …

Fluid Flow Through Deformation Band, Huining Zhang

Masters Theses

"Cataclastic deformation bands, which are common in porous sandstone, have the potential to restrict fluid flow. Geological studies have shown that permeability of deformation band shear zones can be one to five orders of magnitude less than for the sandstone host rock. However, recent studies based on simplified analytical estimates have shown that fluid flow in jointed deformation bands may not be retarded since joints play an important role in conducting fluids. In this study, 2 dimensional finite element analysis (FEA) is used to simulate the total discharge flow rate through jointed deformations. Variations of single planar and conjugate jointed …

A Linear Matrix Inequality-Based Approach For The Computation Of Actuator Bandwidth Limits In Adaptive Control, Daniel Robert Wagner

Masters Theses

"Linear matrix inequalities and convex optimization techniques have become popular tools to solve nontrivial problems in the field of adaptive control. Specifically, the stability of adaptive control laws in the presence of actuator dynamics remains as an important open control problem. In this thesis, we present a linear matrix inequalities-based hedging approach and evaluate it for model reference adaptive control of an uncertain dynamical system in the presence of actuator dynamics. The ideal reference dynamics are modified such that the hedging approach allows the correct adaptation without being hindered by the presence of actuator dynamics. The hedging approach is first …

A Statistical Analysis Of A 4.5 Mw Solar Energy Center, Archit Patnaik

Masters Theses

"This project helps a regional utility evaluate the performance of their 4.5 MW photovoltaic plant. The performance evaluation consists of characterizing the peak and average power and energy output of the plant over varying time periods. A characterization of the output power drops, or dips, is done by performing a statistical analysis of the photovoltaic plant output data. Dips are characterized by dip frequency, depth of dip, energy loss by dip, and dip duration. The results of this study will help the utility to select appropriate voltage regulating equipment on the basis of dip characteristics, and thus, optimize the performance …

Conceptual Parameters Necessary For Modeling Wettability Alteration In An Enhanced Smart Brine-Chalk System, Ahmed Abdulkareem Hussein Albahrani

Masters Theses

"Achieving higher recovery of oil from proven carbonate reserves around the world is not an easy task. One promising new method, especially for carbonate reservoirs, is the use of "Smart Water" technology, which is an injection water with carefully determined, optimal ionic composition and salinity. Recent experiments have shown good recovery results, but the mechanism of wettability alteration by this fluid are still not well understood. The goal of this study is to review the high and optimal salinity and ionic composition literature plus perform dimensional analysis of key variables in order to shed light on the physical and chemical …

Design And Analysis Of An Axisymmetric Aerospike Supersonic Micro-Nozzle For A Refrigerant-Based Cold-Gas Propulsion System For Small Satellites, Abdalla Ali Bani

Masters Theses

"The cold-gas propulsion system being developed by M-SAT requires improvements to its original nozzle design. This study documents the research, design, and analysis of a supersonic plug nozzle concept that could be integrated to the refrigerant-based cold-gas propulsion system to possibly improve its performance. As documented in this thesis, CFD analysis showed that the outlined nozzle design method resulted in a feasible nozzle concept that has the ability to out-perform a conventional nozzle of the same area ratio. The flow-fields and thrust of the aerospike nozzle, for the full and truncated nozzles, were investigated. The purpose of this study is …