Engineering Commons^™

An Experimental Investigation Of Heat Transfer For Arrays Of Impingement Jets Onto The Featured Surfaces With Cylindrical And Elliptical Raised Surfaces, Marc A. Medina

Honors Undergraduate Theses

This study focuses on multi-jet impingement for gas turbine geometries in which the objective is to understand the influence of the roughness elements on a target surface to the heat transfer. Current work has proven that implementing roughness elements for multi-jet impingement target surfaces has increased heat transfer ranging anywhere from 10-30%. This study has chosen to investigate three different roughness elements, elliptical in cross-section, to compare to smooth surface geometries for multi-jet impingement. An experimental was taken for this study to extend the current knowledge of multi-jet impingement geometries and to further understand the heat transfer performance. A temperature …

Conjugate Heat Transfer Analysis Of Combined Regenerative And Discrete Film Cooling In A Rocket Nozzle, Charlotte M. Pearce

Honors Undergraduate Theses

Conjugate heat transfer analysis has been carried out on an 89kN thrust chamber in order to evaluate whether combined discrete film cooling and regenerative cooling in a rocket nozzle is feasible. Several cooling configurations were tested against a baseline design of regenerative cooling only. New designs include combined cooling channels with one row of discrete film cooling holes near the throat of the nozzle, and turbulated cooling channels combined with a row of discrete film cooling holes. Blowing ratio and channel mass flow rate were both varied for each design. The effectiveness of each configuration was measured via the maximum …

Characterization Of Dispersion And Residual Stress In Nanoparticle Reinforced Hybrid Carbon Fiber Composites, Alex Selimov

Honors Undergraduate Theses

Hybrid carbon fiber reinforced composites are a new breed of materials that are currently being explored and characterized for next generation aerospace applications. Through the introduction of secondary reinforcements, such as alumina nanoparticles, hybrid properties including improved mechanical properties and stress sensing capabilities can be achieved. In order to maximize these properties, it is necessary to achieve a homogeneous dispersion of particulate filler. Utilizing the photoluminescent properties of alumina, it is possible to compare local levels of particle concentration through emission intensities as a way to determine the effectiveness of the tested manufacturing parameters in increasing material homogeneity. Parameters of …

The Mechanical Response And Parametric Optimization Of Ankle-Foot Devices, Kevin Smith

Electronic Theses and Dissertations

To improve the mobility of lower limb amputees, many modern prosthetic ankle-foot devices utilize a so called energy storing and return (ESAR) design. This allows for elastically stored energy to be returned to the gait cycle as forward propulsion. While ESAR type feet have been well accepted by the prosthetic community, the design and selection of a prosthetic device for a specific individual is often based on clinical feedback rather than engineering design. This is due to an incomplete understanding of the role of prosthetic design characteristics (e.g. stiffness, roll-over shape, etc.) have on the gait pattern of an individual. …

Intrinsic Modulation Response Modeling And Analysis For Lithographic Vertical-Cavity Surface-Emitting Lasers, Mingxin Li

Electronic Theses and Dissertations

Vertical-cavity surface-emitting lasers (VCSELs) have been greatly improved and successfully commercialized over the past few decades owing to their ability to provide both mode and current confinement that enables low energy consumption, high efficiency and high modulation speed. However, further improvement of oxide VCSELs is limited by the nature of the oxide aperture because of self-heating, internal strain and difficulties in precise size control. In this dissertation, VCSELs using lithographic approach are demonstrated to overcome the limitations of oxide VCSELs, in which an intra-cavity phase shifting mesa is applied to define the device size and provide optical mode and electrical …

The Woz Recognizer: A Tool For Understanding User Perceptions Of Sketch-Based Interfaces, Jared Bott

Electronic Theses and Dissertations

Sketch recognition has the potential to be an important input method for computers in the coming years; however, designing and building an accurate and sophisticated sketch recognition system is a time consuming and daunting task. Since sketch recognition is still at a level where mistakes are common, it is important to understand how users perceive and tolerate recognition errors and other user interface elements with these imperfect systems. A problem in performing this type of research is that we cannot easily control aspects of recognition in order to rigorously study the systems. We performed a study examining user perceptions of …

Broad Bandwidth Optical Frequency Combs From Low Noise, High Repetition Rate Semiconductor Mode-Locked Lasers, Anthony Klee

Electronic Theses and Dissertations

Mode-locked lasers have numerous applications in the areas of communications, spectroscopy, and frequency metrology. Harmonically mode-locked semiconductor lasers with external ring cavities offer a unique combination of benefits in that they can produce high repetition rate pulse trains with low timing jitter, achieve narrow axial mode linewidths, have the potential for entire monolithic integration on-chip, feature high wall-plug efficiency due to direct electrical pumping, and can be engineered to operate in different wavelength bands of interest. However, lasers based on InP/InGaAsP quantum well devices which operate in the important telecom C-band have thus far been relatively limited in bandwidth as …

Advanced Blue Phase Liquid Crystal Displays, Daming Xu

Electronic Theses and Dissertations

Thin-film transistor (TFT) liquid crystal displays (LCDs) have become indispensable in our daily lives. Their widespread applications range from smartphones, laptops, TVs to navigational devices, data projectors and wearable displays. Over past decades, massive efforts have been invested in device development, material characterization and manufacturing technology. As a result, the performance of LCDs, such as viewing angle, contrast ratio, color gamut and resolution, have been improved significantly. Nonetheless, there are still urgent needs for fast response time and low power consumption. Fast response time helps reduce motion image blurs and enable color sequential displays. The latter is particularly attractive since …

Dynamic Modeling Of Autorotation For Simultaneous Lift And Wind Energy Extraction, Sadaf Mackertich

Electronic Theses and Dissertations

The goal of this thesis is to develop a multi-body dynamics model of autorotation with the objective of studying its application in energy harvesting. A rotor undergoing autorotation is termed an Autogyro. In the autorotation mode, the rotor is unpowered and its interaction with the wind causes an upward thrust force. The theory of an autorotating rotorcraft was originally studied for achieving safe flight at low speeds and later used for safe descent of helicopters under engine failure. The concept can potentially be used as a means to collect high-altitude wind energy. Autorotation is inherently a dynamic process and requires …

A Holistic Framework For Effective Engineering Leadership Development Using 3d Virtual World Simulation, Hamed Almalki

Electronic Theses and Dissertations

Problems associated with the limited success of traditional engineering leadership development are the absence of embedded real-life industry case studies in leadership development and incorrect applications of leadership strategies in the various contexts. Though recommended programs for enhancing leadership development exist, they lack an examined framework, especially when it comes to leadership development of undergraduate engineering students. In this research effort, the impact of a framework using 3D virtual world simulation and the 4-D Leadership System to enhance the leadership abilities of undergraduate engineering students at the individual and team levels based on industrial leadership case studies was investigated. The …

Multi-Purpose Device For Analyzing And Measuring Ultra-Short Pulses, Naman Anilkumar Mehta

Electronic Theses and Dissertations

Intensity auto correlator is device to measure pulse widths of ultrashort pulses on the order of picoseconds and femtoseconds. I have built an in-house, compact, portable, industry standard intensity auto correlator for measuring ultrashort pulse-widths. My device is suitable for pulse-widths from 500 ps to 50 fs. The impetus for developing this instrument stemmed from our development of a multicore-fiber laser for high power laser applications, which also produces very short pulses that cannot be measured with an oscilloscope. As techniques for measuring short pulse-widths have been well studied, what made my journey exciting was the process of taking an …

Geometric Consideration Of Nanostructures For Energy Storage Systems, Jonghyun Park, Jie Li, Wei Lu, Ann Marie Sastry

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Battery performance and its fade are determined by various aspects such as the transport of ions and electrons through heterogeneous internal structures; kinetic reactions at the interfaces; and the corresponding interplay between mechanical, chemical, and thermal responses. The fundamental factor determining this complex multiscale and multiphysical nature of a battery is the geometry of active materials. In this work, we systematically consider the tradeoffs among a selection of limiting geometries of media designed to store ions or other species via a diffusion process. Specifically, we begin the investigation by considering diffusion in spheres, rods, and plates at the particle level, …

Enabling Method To Design Versatile Biomaterial Systems From Colloidal Building Blocks, Shalini Saxena, L. Andrew Lyon

Biology, Chemistry, and Environmental Sciences Faculty Articles and Research

Development of materials with fine spatial control over topographical, mechanical, or chemical features has been investigated for a variety of applications. Here we present a method to fabricate an array of polyelectrolyte constructs including two-dimensionally and three-dimensionally patterned assemblies using both compressible and incompressible colloidal building blocks. This method eliminates prior constraints associated with specific chemistries, and can be used to develop modular, multi-component, patterned assemblies. In particular, development of constructs were investigated using microgels, which are colloidally stable hydrogel microparticles, polystyrene (PS) beads, and PS-microgel core-shell building blocks in conjunction with the polycation poly(ethyleneimine) (PEI). The topography, mechanical properties, …

Impacts Of Music On Sectional View Drawing Ability For Engineering Technology Students As Measured Through Technical Drawings, Petros J. Katsioloudis, Mildred Jones, Vukica Jovanovic

STEMPS Faculty Publications

Results from a number of studies indicate that the use of different types of music can influence cognition and behavior; however, research provides inconsistent results. Considering this, a quasi-experimental study was conducted to identify the existence of statistically significant effects on sectional view drawing ability due to the impacts of music. In particular, the study compared the use of three different types of music; classical, rock, heavy metal and whether a significant difference exists towards sectional view drawing ability, among engineering technology students. According to the results of this study it is suggested that the impact of music provides no …

Web Tools: Keeping Learners On Pace, Mickey Kosloski

STEMPS Faculty Publications

One of the greatest challenges in teaching technology and engineering is pacing. Some students grasp new technological concepts quickly, while others need repetition and may struggle to keep pace. This poses an obstacle for the technology and engineering teacher, and is particularly true when teaching students to build a website. However, there are a plethora of online tools available that can assist learners in building a website. This article identifies some of the tools that may be used in the classroom and for classroom-oriented, teacher-hosted websites. While specific examples are provided, Web search terms are denoted at the end of …

Spatial-Temporal Stochasticity Of Electric Vehicles In Integrated Traffic And Power System, Sadhana Shrestha

Electronic Theses and Dissertations

A penetration of a large number of electric vehicles for charging their batteries in the grid can have a negative impact to the grid. To prevent a negative effect to the grid, the behavior of electric vehicles must be accurately modeled and their charging schedules must be coordinated. Therefore, it is necessary to determine where and how much charge is available in electric vehicles in the distribution system. In this thesis, a state transition algorithm is designed to determine a stochastic model of electric vehicles to simulate electric vehicle movement in an integrated traffic and power network. Dijkstra’s algorithm is …

Ultrasonic Doppler Sonar Sensor System For Extraction Of Walk Signatures, Demba B. Komma

Honors Theses

In this work, a portable low cost sensor system is designed for the extraction of walking signatures in humans using the principle of Ultrasonic Doppler Sonar (UDS). UDS involves the use of two ultrasonic transducers acting as a transmitter-receiver pair. The transmitter produces a continuous ultrasonic signal at a specific frequency to be broadcasted onto a moving target, while the receiver will perform a frequency shift on the reflected signal in relation to the movement of the target. The sensor system used in this work is comprised of a frequency generator that drives the transducer with a 40 kHz sine …

Eliminating Magnetic Forces From The Surface Tension Measurement Of Magnetic Surfactants, Emily Koehler

Honors Theses

Surfactants have many applications due to their ability to reduce the surface tension between two phases. Magnetic surfactants, a relatively new form of surfactants, offer the possibility of further controlling a surfactant system by using an external magnetic field to induce alignment on the molecular level. One method of studying a magnetic field's effect on the magnetic surfactant system involves analyzing the change in surface tension at varied solution concentrations both in and outside a magnetic field. The pendent drop method uses the downward gravitational force on a droplet suspended from a needle to find the surface tension based on …

Analyzing Data Of Thin-Film Photovoltaic Cells, Eric Ng, Shubra Bansal

AANAPISI Poster Presentations

The purpose of this study is to determine the basic device characteristics from the Current-Voltage curve of perovskite photovoltaic cells. Martin Green’s “Solar cell efficiency tables (Version 45)” highlighted the accomplishments in photovoltaic cell research for the year 2015. One notable achievement was done by KRICT using perovskites to achieve a 20.1% efficiency. According to Wall Street Journal article “Perovskite Offers Shot at Cheaper Solar Energy”, Ulicia Wang (2014) reports that perovskites have “achieved a jump in efficiency to 20% from around 10% just two years ago.”

Behavior Of Concrete Beams With Corroded Reinforcement Retrofitted With Carbon Fiber Reinforced Polymer, Needa Marwan Lingga

Civil and Environmental Engineering Master's Project Reports

Severe premature deterioration has been reported in a large number of reinforced concrete (RC) structures in corrosive environments. This research project focused on the behavior of beams that contained corroded steel and were retrofitted with CFRP. The steel in RC beams were assumed to be fully corroded, representing the most severe loss in steel cross-section. Unidirectional CFRP sheets were used to strengthen the deteriorated beams. The experimental program included testing five simply supported rectangular cross section concrete beams. All beams were approximately 1/3^rd scale models, 4in. x 6in. cross sections, and 6ft. long. In three beams, the oiled steel …

A Study On The Current State Of Contaminants Of Concern Research, With A Focus On Biosolids And Regulations, Maren Mariah Fulton

Civil and Environmental Engineering Master's Project Reports

Wastewater treatment plants are a major source of contaminants of emerging concern, as these facilities are the main receptors of these products via household, commercial, and industrial drains, and transport via stormwater runoff. Biosolids are composed of numerous constituents, with a number of environmentally persistent and potentially toxic contaminants of emerging concern identified as present in large concentrations. Research is needed to understand the transport and fate mechanisms of these compounds in biosolids. Additionally, this research is needed to determine a new priority framework to regulate CECs, both on the national level and regional levels. Wastewater treatment plant influent and …

Airline Pilot Supply In The Us: Factors Influencing The Collegiate Pilot Pipeline, Rebecca K. Lutte, Kent Lovelace

Aviation Institute Faculty Publications

In the era following the First Officer Qualification (FOQ) rule change, regional airlines are struggling to meet hiring needs. Prior to the rule change, pilots were willing to fly for regional airlines at low pay as a stepping-stone to a career at major airlines. Since the rule change, higher minimum qualifications requiring a greater investment for aspiring pilots appear to have impacted the appeal of this career path. This study explores that claim with the purpose of understanding the impact of the FOQ rule change on the career aspirations of collegiate aviation flight students and examining student perceptions of the …

Optimal Digital Control Of A Three-Phase Four-Leg Voltage Source Inverter, Ayhan Özdemi̇r, Zeki̇ye Erdem

Turkish Journal of Electrical Engineering and Computer Sciences

No abstract provided.

Reference Point Indentation Of Human Trabecular Bone Treated With Bisphosphonates For Varying Durations, Drew Jones

Theses and Dissertations--Biomedical Engineering

Reference point indentation (RPI), a novel form of micro-indentation, quantifies RPI material parameters which correlate with modulus, yield stress, strength, or toughness. Information linking bisphosphonate treatment length with the material properties of osteoporotic trabecular bone is needed to improve patient treatment. The objectives of this study were to: 1) determine if RPI can be used to successfully evaluate human trabecular bone and if so, determine an optimized test method for using RPI on trabecular bone, and 2) use this method to determine if any RPI parameters are related to the duration of bisphosphonate treatment.

Indentation using a 4 N applied …

Closed-Loop Afferent Nerve Electrical Stimulation For Rehabilitation Of Hand Function In Subjects With Incomplete Spinal Cord Injury, Christopher J. Schildt

Theses and Dissertations--Biomedical Engineering

Peripheral nerve stimulation (PNS) is commonly used to promote use-dependent cortical plasticity for rehabilitation of motor function in spinal cord injury. Pairing transcranial magnetic stimulation (TMS) with PNS has been shown to increase motor evoked potentials most when the two stimuli are timed to arrive in the cortex simultaneously. This suggests that a mechanism of timing-dependent plasticity (TDP) may be a more effective method of promoting motor rehabilitation. The following thesis is the result of applying a brain-computer interface to apply PNS in closed-loop simultaneously to movement intention onset as measured by EEG of the sensorimotor cortex to test whether …

Detection Of Electrical Alternans In Ventricular Depolarization Phase Of Human Electrocardiogram, David R. Wasemiller

Theses and Dissertations--Biomedical Engineering

T-wave Alternans (TWA) in an electrocardiogram (ECG) has received considerable interest as a potential predictor of sudden cardiac death (SCD). However, large clinical trials have shown that while TWA has a very high negative predictive value, its positive predictive value is poor. Results of previous studies suggest that arrhythmia onset can be affected by the phase relationship of alternans of the depolarization and repolarization phase of the action potentials of the ventricles. To assess this relationship, one would first need to establish that depolarization alternans can be detected and then develop methods to determine its relationship with repolarization alternans, which …

Use Of Laboratory Geophysical And Geotechnical Investigation Methods To Characterize Gypsum Rich Soils, Raghava A. Bhamidipati

Theses and Dissertations--Civil Engineering

Gypsum rich soils are found in many parts of the world, particularly in arid and semi-arid regions. Most gypsum occurs in the form of evaporites, which are minerals that precipitate out of water due to a high rate of evaporation and a high mineral concentration. Gypsum rich soils make good foundation material under dry conditions but pose major engineering hazards when exposed to water. Gypsum acts as a weak cementing material and has a moderate solubility of about 2.5 g/liter. The dissolution of gypsum causes the soils to undergo unpredictable collapse settlement leading to severe structural damages. The damages incur …

Forecasting Long Term Highway Staffing Requirements For State Transportation Agencies, Ying Li

Theses and Dissertations--Civil Engineering

The transportation system is vital to the nation’s economic growth and stability, as it provides mobility for commuters while supporting the United States’ ability to compete in an increasingly competitive global economy. State Transportation Agencies across the country continue to face many challenges to repair and enhance highway infrastructure to meet the rapid increasing transportation needs. One of these challenges is maintaining an adequate and efficient agency staff. In order to effectively plan for future staffing levels, State Transportation Agencies need a method for forecasting long term staffing requirements. However, current methods in use cannot function without well-defined projects and …

Study Of Macroturbulence And Bursting Via The -1 Spectral Power Law Region Of Turbulent Open Channel Flows Over Gravel Beds, Amirreza Ghasemi

Theses and Dissertations--Civil Engineering

The large scale and smaller production scale motions contain over the half of turbulent kinetic energy in the flow. These motions are responsible for sediment transport and deposition processes, contaminant mixing and stream bio-diversity. These motions are corresponded to the left and right bounds of -1 power region of the spectral energy. The most well recognized and highly studied power law has been upon Kolmogorov’s -5/3 power law region of the streamwise spectral energy density and this research focused on investigating the -1 power region bounds and energy. Energy budget and time-average turbulence calculations along with spectral analysis …

Evaluating Arterial Congestion And Travel Time Reliability Performance, Galen T. Smith

Theses and Dissertations--Civil Engineering

This thesis presents an investigation of arterial travel time and reliability. Specifically an examination of the proposed arterial travel time reliability performance measures detailed in Federal Highway Administration’s Notice of Proposed Rulemaking on national performance management measures are performed. These measures, including level of travel time reliability and peak hour travel time ratio, are computed and compared to those currently used to quantify congestion and travel time reliability. Within this process several commonly used data sources are evaluated to determine the effects of data quality and data source on performance measure evaluation. The newly created Urban Streets Reliability tool is …