Engineering Commons^™

Modeling Of Nitrogen Separation From Natural Gas Through Nanoporous Carbon Membranes, Moustafa A. Soliman, A A. Al-Rabiah, Abdelhamid M. Ajbar, F A. Almalki, Omar Y. Abdelaziz

Chemical Engineering

This work presents a theoretical investigation of the use of nanoporous carbon membranes for the separation of nitrogen from natural gas. A mathematical model to predict the performance of the membrane is developed. The model is a combination of the well known dusty gas model, which describes the transfer of multi-components mixture in porous media, together with a surface diffusion model. The model is first validated using the literature results for the separation of hydrogen from hydrocarbons mixture. The model is then applied to the nitrogen-hydrocarbons system. The membrane performance is evaluated in terms of nitrogen recovery, methane loss, nitrogen …

Advances In Direct Formic Acid Fuel Cells: Fabrication Of Efficient Ir/Pd Nanocatalysts For Formic Acid Electro-Oxidation, Islam M. Al-Akraa, Ahmad M. Mohammad, Mohamed S. El-Deab Prof, Bahgat E. El-Anadouli Prof

Chemical Engineering

No abstract provided.

Simulation Of Dpm Distribution In A Long Single Entry With Buoyancy Effect, Yi Zheng, Magesh Thiruvengadam, Hai Lan, Jerry Tien C.

Mining Engineering Faculty Research & Creative Works

Diesel particulate matter (DPM) is considered carcinogenic after prolonged exposure. With more diesel-powered equipment used in underground mines, miners' exposure to DPM has become an increasing concern. This paper used computational fluid dynamics (CFD) method to study DPM distribution based on an experiment conducted by the Diesel Emissions Evaluation Program (DEEP) in Canada. Twenty-four cases were simulated where the emissions from both truck and load-haul-dumps (LHDs) were examined. Each vehicle was placed in two stream wise locations, and the vehicles were oriented either facing or with the rear end toward the main fresh airflow. A species transport model with buoyancy …

Poll Everywhere! Even In The Classroom: An Investigation Into The Impact Of Using Polleverwhere In A Large-Lecture Classroom, Wendi M. Kappers, Stephanie L. Cutler

Publications

Over the past several years, there has been a call in higher education to move from traditional lecturing to a more active classroom. However, many faculty members face multiple challenges when attempting to make a large lecture (over 100 students) an active learning environment. One way researchers have suggested engaging a large lecture is through Concept Tests and Peer Instruction, which can require additional resources to be purchased by students, such as electronic response systems or "clickers." This study will investigate the applicability of utilizing the free software PollEverywhere, which can be accessed using student cell phones (Text messages and …

Mobile Apps In Collection Development: Supporting A Mobile Learning Environment, Stefanie Havelka, Rebecca Arzola

Publications and Research

We will discuss our rationale and thoughts on why we believe mobile apps should be part of a library’s collection development policy. An updated policy with apps encourages a mobile learning environment that is technologically diverse while being holistically supportive of its users and research.

A Process-Based Nutrient Model For The Bedded Manure Pack Of Confined Beef Systems, Ferouz Y. Ayadi

Electronic Theses and Dissertations

Manure management is of growing concern for beef cattle producers and the general public. The overall objective of this research was to develop a process-based model that predicts concentration and gaseous emission from the bedded manure pack of a confined beef cattle system, with respect to different bedding material, manure storage time, and ambient temperature. The model incorporated the data collected in three experiments designed to understand transformations and processes occurring in the bedded pack. The first study evaluated the source of volatilized ammonia nitrogen from beef cattle manure. Isotope ratio mass spectrometry was used to determine the origin of …

Studies Related To Microbially Induced Corrosion Of Stainless Steel 304 And 316, Somil Gupta

Electronic Theses and Dissertations

Pitting corrosion of stainless steel (SS) is observed in many different industries including the dairy industry. It is of concern, because it weakens the steel, and can cause cracking. Any replacement or repair of SS equipment is very costly and also causes delays in product manufacture. Microbial Induced Corrosion (MIC) is a possible accelerator of natural corrosion seen in galvanized steel pipes. Studies have shown a correlation between surface roughness and the ability of bacteria to colonize and form biofilms. Dairy industry utilizes higher food grade SS 304 and 316. However, even these relatively corrosion resistant stainless steel grades may …

A Multi-Directional Treadmill Training Program For Improving Gait, Balance, And Mobility In Individuals With Parkinson’S Disease: A Case Series, Kimberly Smith, Kurt Jackson, Kimberly Edginton Bigelow, Lloyd L. Laubach

Mechanical and Aerospace Engineering Faculty Publications

Treadmill training is a commonly used intervention for improving gait in people with Parkinson’s disease (PD). However, little is known about how treadmill training may also influence balance and other aspects of mobility.

The purpose of this case series was to explore the feasibility and possible benefits of multi-directional treadmill training for individuals with PD. Four participants (62.3 ± 6.5 yrs, Hoehn & Yahr 2-4) performed 8 weeks of treadmill training 3 times per week. Weeks 1-4 included forward walking only, while weeks 5-8 included forward and multi-directional walking. Participants were tested every 4 weeks on 4 separate occasions. Outcome …

Novel Pulsatile Cardiac Assist Pump, Lakshmi Mohanadas

Wayne State University Theses

The project involve the research and development of a pulsatile, complex or continuous flow in biological and non-biological systems implantable heart assist pump. Specifically as a 20% cardiac assist for persons from congestive heart failure and other cardiac abnormalities. The pulsatile cardiac assist pump would provide upto 20% of the blood pumping process from the venous supply to the arterial supply. Current pumps are largely complete bypass pumps or large volume pumps that produce significant long term blood cell damage resulting in thrombosis. Most are not pulsatile which offers a significant physiological advantage. The pump under development is designed to …

Fabrication And Characterization Of A Robust, Field- Deployable, Optical Sensor Designed To Detect Particles In Oils., Navya Pandreka

Wayne State University Theses

Some types of bacteria and fungus can use iron or non-ferrous metals for their metabolic process. Sulfate-reducing bacteria can corrode pipes in the oil industry and high-end machinery. Both aerobic and anaerobic bacteria often degrade fuel quality and cause fuel system corrosion or alter the chemical properties of the fluid. This causes significant economic damage and safety concerns. Therefore, there is a need for a system to continuously monitor fuel or lubricant oil for the presence of bacteria and fungus.

The main goal of this project was to develop a sensor that can detect bacteria and other ferrous and non-ferrous …

A Customer Choice Modeling Framework For Assortment Planning Of Configurable Products In Automotive Industry, Farah Dubaisi

Wayne State University Theses

Due to the increased competition in the auto industry, proliferation of the vehicle models and increased customer need for choice and customization, it has become more critical than ever to offer a variety of features and customization flexibility while at the same time restraining and, even better, cutting down the costs. Product complexity, in the automotive industry, can be measured by the size of the assortment offered, i.e., set of vehicle configurations a customer can choose from (e.g., for a given model of a brand). While complexity fosters growth with increased alignment of product characteristics and customer needs, it results …

The Design And Vlsi Implementation Of Digital Arithmatic Processors - A Case Study Of A Generalized Pipeline Cellular Array, Yudi Xie

Wayne State University Theses

A generalized pipeline array appeared in IEEE transaction in 1974. The array appeared in a few textbooks on computer arithmetic. From time to time, a number of papers appeared which reflected the modifications of this array. The objective of this thesis is to present the design and VLSI implementation of this array, which can add, subtract, multiply, divide, square and square root of binary numbers. In this thesis, we suggest a step-by-step procedure by which the design can be sent to MOSIS and to get the fabricated chip back. The array has been extended from 5 rows to 7 rows …

The Study Of Ionization In A Military, Heavy-Duty, Diesel Engine, Steven Zielinski

Wayne State University Theses

This thesis is an investigation of ionization in a military, heavy-duty, diesel engine. Ionization is a phenomenon which occurs in both spark-ignited and diesel engines. During the reactions of combustion, charged molecules and electrons are produced. The current produced, ion current, from these charges can be measured. The measurement of ion current can serve as an in-cylinder diagnostic for closed-loop engine control strategies. In this work, a literature review was performed to survey previous work as it pertains to ionization in diesel engines. In addition, a detailed description and comparison of the HEUI injection system was made to HPCR. This …

Predictive Analytics For Disease Condition Of Patients In Emergency Department, Azade Tabaie

Wayne State University Theses

Emergency Departments (EDs) in hospitals are experiencing severe crowding and prolonged patient waiting times. The reported crowding in hospitals shows patients in hospital hallways, long waiting times and full occupancy of ED beds. ED crowding has several potential unfavorable effects including patients and staff frustration, lower patient satisfaction and poor health outcomes. The primary motivations behind this study are shortening the patients’ waiting time and improving patient satisfaction and level of care.

The very initial interaction between clinicians and a patient is recorded on nurse triage notes which contain details of the reason for patient’s visit including specific symptoms and …

High Surface Area And Z′ In A Thermally Stable 8-Fold Polycatenated Hydrogen-Bonded Framework, Cassandra A. Zentner, Holden W.H. Lai, Joshua T. Greenfield, Ren A. Wiscons, Matthias Zeller, Charles F. Campana, Orhan Talu, Stephen A. Fitzgerald, Jesse L.C. Rowsell

Chemical & Biomedical Engineering Faculty Publications

1,3,5-Tris(4-carboxyphenyl)benzene assembles into an intricate 8-fold polycatenated assembly of (6,3) hexagonal nets formed through hydrogen bonds and π-stacking. One polymorph features 56 independent molecules in the asymmetric unit, the largest Z′ reported to date. The framework is permanently porous, with a BET surface area of 1095 m² g⁻¹ and readily adsorbs N₂, H₂ and CO₂.

Effects Of Posttensioning Slippage On 2-Way Spanning Concrete Slabs, Niall Holmes, Eoin Byrne

Articles

This paper investigates the effect of improper posttensioning of a 2-way spanning concrete slab subject to a central point load. Due to plate slippage alone, the support conditions only offered a 1-way spanning action which could have led to premature failure with dangerous consequences. Posttensioning can strengthen a flat slab against punching shear by controlling deflections and cracking under service loads compared with traditional punching shear reinforcing methods leading to more slender structures and economic solutions for longer spans. However, if the method is not properly applied, these thinner floor plates can fail in a brittle and sudden manner by …

Nonlinear Analysis Of Isotropic Slab Bridges Under Extreme Traffic Loading, Donya Hajializadeh, A. Salam Al-Sabah, Eugene J. Obrien, Debra F. Laefer, Bernard Enright

Articles

Probabilistic analysis of traffic loading on a bridge traditionally involves an extrapolation from measured or simulated load effects to a characteristic maximum value. In recent years, Long Run Simulation, whereby thousands of years of traffic are simulated, has allowed researchers to gain new insights into the nature of the traffic scenarios that govern at the limit state. For example, mobile cranes and low-loaders, sometimes accompanied by a common articulated truck, have been shown to govern in most cases. In this paper, the extreme loading scenarios identified in the Long Run Simulation are applied to a non-linear, two-dimensional (2D) plate finite …

Adopting Problem Based Learning In Third Level Computer Science, Martin Mchugh

Reports

It has been recognised that the traditional teaching approach of the teacher being solely a transmitter and the student being a receiver is not sufficient. This is evident when a traditional style of teaching is compared to a more hands-on approach to learning. When discussing the traditional style of teaching, Earl and Ellington (1999, p.83) describe how in this approach to learning; (current) teaching methods are almost invariably of the ‘face-to-face’ type. The whole system is generally geared towards the smooth operation of the teaching institution, with little or no attempt being made to cater for the different learning styles …

Professional Formation Of Engineers: Enhancing The First Year Student Experience, Eileen Goold

Conference Papers

This paper reports on a study investigating engineering students’ perceptions of engineering practice and whether engineering students’ cognitive engagement benefits from bridging the gap between the technical issues in their education and the practical realities of modern engineering practice.

Engineering Students’ Perceptions Of Their Preparation For Engineering Practice, Eileen Goold Dr

Conference Papers

A common theme in the scholarly literature describing engineering is associated with the conception of the term global engineer where the role of the engineer has become quite broad. This study investigates engineering students’ perceptions of their future careers and their preparation for professional practice. This is important information for engineering educators as students with heightened interest in professional practice demonstrate more cognitive engagement. Additionally many graduate engineers are challenged by the transition into engineering practice. A mixed methods approach is employed. The degree competencies are required and learned by electronic engineering students, at the Institute of Technology Tallaght Dublin, …

Molecular Dynamics Study On Defect Reduction Strategies Towards The Fabrication Of High Performance Cd1-Xznxte/Cds Solar Cells, Jose Juan Chavez

Open Access Theses & Dissertations

Cadmium Telluride is a material widely used in terrestrial thin film photovoltaic applications due to its nearly ideal band gap (~1.5 eV) and high absorption coefficient. Due to its low manufacturing cost, this technology has the potential to become a significant energy resource if higher energy conversion efficiencies are achieved. However, the module efficiencies (~14%) are still far from the theoretical maximum (~30%) for this material in a single junction configuration. The reason behind this low performance is attributed to the high number of defects that are present within the device materials. The physics behind the formation mechanisms of these …

Modeling And Preliminary Characterization Of Passive, Wireless Temperature Sensors For Harsh Environment Applications Based On Periodic Structures, Diego Ivan Delfin Manriquez

Open Access Theses & Dissertations

Wireless temperature sensing has attained significant attention in recent years due to the increasing need to develop reliable and affordable sensing solutions for energy conversion systems and other harsh environment applications. The development of next generation sensors for energy production processing parameters, such as temperature and pressure, can result in better performance of the system. Particularly, continuous temperature monitoring in energy conversion systems can result in enhancements such as better system integrity, less pollution and higher thermal efficiencies. However, the conditions experienced in these system components hinder the performance of current solutions due to the presence of semi-conductor materials and …

Optimization Of Green Logistics Using Genetic Algorithm Approach, Gabriela Ituarte-Villarreal

Open Access Theses & Dissertations

Green Logistics (GL) becomes critical in Supply Chain Management (SCM) due to it having less of an impact to the environment. Green Logistics optimization refers to the determination depot quantity, decreasing uncovered demand and CO2 emission reduction. To date, application of Genetic Algorithm (GA) has been proven to be very efficient and reliable in solving optimization problems; it is also capable of operating simultaneously with multiple solutions. Basically, GA imitates the natural evolution of a population with initial solutions. In this Thesis a modified Genetic Algorithm is proposed to solve the multiple objective GL optimization problem. MATLAB software is used …

Simulation Of Infiltrating Rate Driven By Surface Tension-Viscosity Of Liquid Elements From The Titanium Group Into A Packed Bed, Arturo Medina

Open Access Theses & Dissertations

The simulation of infusion of molten reactive metals (e.g., yttrium) into a porous, carbide packed bed to create carbide and boride composites was studied at ultrahigh temperatures (>1700°C). The infusion was investigated through a computational fluid dynamic (CFD) system of capillary pores and compared to a predicted analytical calculation formulated by Selmak and Rhines. Simulations of two-phase flow penetration of yttrium into a packed bed of B4C were investigated and compared with titanium, zirconium, hafnium, and samarium liquids. The non-reactive, liquid metal infusion was primarily driven by the surface tension and viscosity. The liquid metal depth and rate of …

Sustainable River-Basin Salinity Management: Treatment Of Natural Brine Springs For Recovery Of Purified Sodium Chloride And Other Valuable Minerals, Priscilla L. Sandoval

Open Access Theses & Dissertations

A treatment process was developed to extract sodium chloride salt, via evaporation, from high-salinity natural brine springs. The source of the brine studied in this project is watershed of the Salt Fork of the Brazos River in Texas. When evaporation is applied to the brine, various impurities precipitate along with the sodium chloride salt (halite). Therefore, a treatment was developed in order to produce a valuable, high-purity salt product. The treatment consists of pretreating the brine with sodium carbonate and hydrochloric acid to for softening and decarbonation. After evaporation, a brine wash post-treatment process was employed to increase the purity …

Hybrid Nano-Structure For Enhanced Energy Storage Devices, Mohammad Arif Ishtiaque Shuvo

Open Access Theses & Dissertations

The goal of this research is to develop electrode materials using various nano-structure hybrids for improved energy storage devices. Enhancing the performance of energy storage device has been gaining tremendous attention since it holds the key solution to advance renewable energy usage thus reduce the consumption of fossil fuels. The application of energy storage devices such as super-capacitor and Li-ion-battery has seen significant growth; however, it is still limited mainly by charge/discharge rate and energy density. One of the solutions is to use nano-structure materials, which offer higher power at high energy density and improved stability during the charge discharge …

Design And Testing Of An Ox/Ch4 Swirl Torch Ignition System, Gabriel Ricardo Trujillo

Open Access Theses & Dissertations

NASA has renewed its interest in oxygen and methane as propellants for propulsion. Some of the reasons that drive this interest are the ease of storage of liquid methane when compared to hydrogen, the handling safety when compared to hypergols, in-situ resource utilization and its relative clean burning process. This project is part of the larger goal of the Center for Space Exploration Technology Research (cSETR) to better understand the aspects of using this propellants to create future hardware that are specifically optimized for their use. This paper discusses the testing of a previous iteration of the swirl torch igniter …

Multi-3d System: Advanced Manufacturing Through The Implementation Of Material Handling Robotics, Jose Luis Coronel Jr.

Open Access Theses & Dissertations

Since the rise of additive manufacturing (AM), innovation has been at the forefront. Additive Manufacturing systems that incorporate complex processes are steadily being developed. One example is the Multi3D System, which was designed to integrate the ability to print multi-material parts with that of embedding electronics. To achieve this automated process, the Multi3D incorporates a six-axis robotic arm to transfer a build platform containing a printed part, to various manufacturing stations (two fused deposition modeling (Stratasys, FDM400mc) systems and a computer numerical control router (Techno CNC Router). The robot is a Yaskawa Motoman MH50 chosen for its payload capacity of …

The Design Of A Modelling, Monitoring And Validation Method For A Solid Wall Structure, Timothy O'Leary, Gillian Menzies, Aidan Duffy

Conference Papers

Hygrothermal assessment is the combined analysis of heat, air and moisture transfer through the building fabric. The two approaches are covered by conventions known as the IS EN 5250:2011 (Glaser method) and IS EN 15026:2007 which differs from Glaser by solving the equations numerically using computer software. Results for hygrothermal analysis provide valuable information for surface and interstitial condensation risk assessment and the impact of energy upgrades. For traditional solid walled structures, conditions such as wind driven rain (WDR) and rising ground water can have a significant impact on the environmental behaviour and in particular the moisture behaviour of the …

The Influence Of Particle Content On The Equi-Biaxial Fatigue Behaviour Of Magnetorheological Elastomers, Yanfen Zhou, Stephen Jerrams, Tony Betts, Gerald Farrell, Lin Chen

Articles

The equi-biaxial fatigue behaviour of silicone based magnetorheological elastomers (MREs) with various volume fractions of carbonyl iron particles ranging between 15% and 35% was studied. Wöhler curves for each material were derived by cycling test samples to failure over a range of stress amplitudes. Changes in complex modulus (E*) and dynamic stored energy during the fatigue process were observed. As for other elastic solids, fatigue resistance of MREs with different particle contents was shown to be dependent on the stress amplitudes applied. MREs with low particle content showed the highest fatigue life at high stress amplitudes while MREs with high …