Engineering Commons^™

An Analysis Of Energy Resources Utilization For Two Metal Joining Manufacturing Processes, Jonathan Gasser

Theses and Dissertations--Mechanical and Aerospace Engineering

Sustainable manufacturing involves utilizing energy resources efficiently. Currently, the state of sustainability for a given manufacturing process is described by most in a qualitative sense as opposed to using quantitative metrics. This thesis offers a segment of analysis needed to understand the state of sustainability in the context of energy resource utilization. This was accomplished by measuring the order of magnitude difference between the energy consumption of a manufacturing process vs. the theoretical minimum amount of energy required to complete the same task (aluminum T-joint bond). This analysis was completed for a TIG welding process and a controlled atmosphere brazing …

Axial Compressor Flow Behavior Near The Aerodynamic Stability Limit, Bradley D. Butler

Theses and Dissertations--Mechanical and Aerospace Engineering

In this investigation, casing mounted high frequency response pressure transducers are used to characterize the flow behavior near the aerodynamic stability limit of a low speed single stage axial flow compressor. Time variant pressure measurements are acquired at discrete operating points up to the stall inception point and during the transition to rotating stall, for a length of time no shorter than 900 rotor revolutions. The experimental data is analyzed using multiple techniques in the time and frequency domains.

Experimental results have shown an increase in the breakdown of flow periodicity as the flow coefficient is reduced. Below a flow …

Theoretical Study Of Thermal Analysis Kinetics, Yunqing Han

Theses and Dissertations--Mechanical and Aerospace Engineering

In the past decades, a great variety of model fitting and model free (isoconversional) methods have been developed for extracting kinetic parameters for solid state reactions from thermally stimulated experimental data (TGA, DSC, DTA etc.). However, these methods have met with significant controversies about their methodologies. Firstly, model-fitting methods have been strongly criticized because almost any reaction mechanism can be used to fit the experimental data satisfactorily with drastic variations of the kinetic parameters, and no good criterion exists to tell which mechanism is the best choice. Secondly, previous model free methods originated from the isoconversional principle, which is often …

Investigation Of Drilling Performance In Cryogenic Drilling On Cfrp Composite Laminates, Tian Xia

Theses and Dissertations--Mechanical and Aerospace Engineering

In recent years, there has been a substantial growth in the application of carbon fiber reinforced plastic (CFRP) composite materials in automobile and aerospace industries due to their superior properties such as lightweight, high strength, excellent corrosion resistance, and minimal fatigue concerns. The present study evaluates the drilling performance of woven carbon fiber reinforced plastics under both dry and cryogenic cooling conditions using uncoated solid carbide drill with a through-hole for coolant application.

The effects of the cooling conditions and the cutting parameters on drilling performance in drilling CFRP were evaluated in terms of generated thrust force, torque, cutting edge …

Shape Memory Behavior Of Single And Polycrystalline Nickel Rich Nickel Titanium Alloys, Irfan Kaya

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTi is the most commonly used shape memory alloy (SMA) and has been widely used for bio-medical, electrical and mechanical applications. Nickel rich NiTi shape memory alloys are coming into prominence due to their distinct superelasticity and shape memory properties as compared to near equi-atomic NiTi shape memory alloys. Besides, their lower density and higher work output than steels makes these alloys an excellent candidate for aerospace and automotive industry. Shape memory properties and phase transformation behavior of high Ni-rich Ni₅₄Ti₄₆ (at.%) polycrystals and Ni-rich Ni₅₁Ti₄₉ (at.%) single-crystals are determined. Their properties are sensitive …

Finite Element Modeling And Fabrication Of An Sma-Smp Shape Memory Composite Actuator, Mohammad Souri

Theses and Dissertations--Mechanical and Aerospace Engineering

Shape memory alloys and polymers have been extensively researched recently because of their unique ability to recover large deformations. Shape memory polymers (SMPs) are able to recover large deformations compared to shape memory alloys (SMAs), although SMAs have higher strength and are able to generate more stress during recovery.

This project focuses on procedure for fabrication and Finite Element Modeling (FEM) of a shape memory composite actuator. First, SMP was characterized to reveal its mechanical properties. Specifically, glass transition temperature, the effects of temperature and strain rate on compressive response and recovery properties of shape memory polymer were studied. Then, …

Estimating Passive Material Properties And Fiber Orientation In A Myocardial Infarction Through An Optimization Scheme Using Mri And Fe Simulation, Dimitri Mojsejenko

Theses and Dissertations--Mechanical and Aerospace Engineering

Myocardial infarctions induce a maladaptive ventricular remodeling process that independently contributes to heart failure. In order to develop effective treatments, it is necessary to understand the way and extent to which the heart undergoes remodeling over the course of healing. There have been few studies to produce any data on the in-vivo material properties of infarcts, and much less on the properties over the time course of healing. In this paper, the in-vivo passive material properties of an infarcted porcine model were estimated through a combined use of magnetic resonance imaging, catheterization, finite element modeling, and a genetic algorithm optimization …

Precipitation, Orientation And Composition Effects On The Shape Memory Properties Of High Strength Nitihfpd Alloys, Emre Acar

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf high temperature shape memory alloys are attractive due to their high operating temperatures (>100 ^oC) and acceptable transformation strain compared to NiTi. However, NiTiHf has limitations due to their lack of ductility and low strength, resulting in poor shape memory properties. In this study, Pd has been added to NiTiHf alloys in an attempt to improve their shape memory behavior. A combined approach of quaternary alloying and precipitation strengthening was used.

The characterization of a Ni_45.3Ti_29.7Hf₂₀Pd₅ (at. %) polycrystalline alloy was performed in compression after selected aging treatments. Transmission electron …

A Design Pathfinder With Material Correlation Points For Inflatable Systems, Jared T. Fulcher

Theses and Dissertations--Mechanical and Aerospace Engineering

The incorporation of inflatable structures into aerospace systems can produce significant advantages in stowed volume to mechanical effectiveness and overall weight. Many applications of these ultra-lightweight systems are designed to precisely control internal or external surfaces, or both, to achieve desired performance. The modeling of these structures becomes complex due to the material nonlinearities inherent to the majority of construction materials used in inflatable structures. Furthermore, accurately modeling the response and behavior of the interfacing boundaries that are common to many inflatable systems will lead to better understanding of the entire class of structures. The research presented involved using nonlinear …

Combining Sustainable Value Stream Mapping And Simulation To Assess Manufacturing Supply Chain Network Performance, Daniel T. Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

Sustainable Value Stream Mapping (Sus-VSM) builds upon traditional VSM to capture additional sustainability aspects of the product flow, such as environmental and societal aspects. This work presents research to expand the utility of Sus-VSM to supply chain networks, develop a general approach towards improving supply chain sustainability, and examine the benefits of implementing simulation and a design of experiments (DOE) style analysis. Metrics are identified to assess economic, environmental, and societal sustainability for supply chain networks and visual symbols are developed for the Supply Chain Sus-VSM (SC Sus-VSM) to allow users to easily identify locations where sustainability can be improved. …

Numerical Analysis Of Droplet Formation And Transport Of A Highly Viscous Liquid, Peiding Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

Drop-on-demand (DOD) inkjet print-head has a major share of the market due to simplicity and feasibility of miniature system. The efficiency of droplet generation from DOD print-head is a result of several factors, include viscosity, surface tension, nozzle size, density, driving waveform (wave shape, frequency, and amplitude), etc. Key roles in the formation and behavior of liquid jets and drops combine three dimensionless groups: Reynolds number, Weber number and Ohnesorge number. These dimensionless groups provide some bounds to the “printability” of the liquid. Adequate understanding of these parameters is essential to improve the quality of droplets and provide guidelines for …

Sustainable Lifetime Value Creation Through Innovative Product Design: A Product Assurance Model, K. Daniel Seevers

Theses and Dissertations--Mechanical and Aerospace Engineering

In the field of product development, many organizations struggle to create a value proposition that can overcome the headwinds of technology change, regulatory requirements, and intense competition, in an effort to satisfy the long-term goals of sustainability. Today, organizations are realizing that they have lost portfolio value due to poor reliability, early product retirement, and abandoned design platforms. Beyond Lean and Green Manufacturing, shareholder value can be enhanced by taking a broader perspective, and integrating sustainability innovation elements into product designs in order to improve the delivery process and extend the life of product platforms.

This research is divided into …

Filtered-Dynamic-Inversion Control For Fixed-Wing Unmanned Aerial Systems, Jon Mullen

Theses and Dissertations--Mechanical and Aerospace Engineering

Instrumented umanned aerial vehicles represent a new way of measuring turbulence in the atmospheric boundary layer. However, autonomous measurements require control methods with disturbance-rejection and altitude command-following capabilities. Filtered dynamic inversion is a control method with desirable disturbance-rejection and command-following properties, and this controller requires limited model information. We implement filtered dynamic inversion as the pitch controller in an altitude-hold autopilot. We design and numerically simulate the continuous-time and discrete-time filtered-dynamic-inversion controllers with anti-windup on a nonlinear aircraft model. Finally, we present results from a flight experiment comparing the filtered-dynamic-inversion controller to a classical proportional-integral controller. The experimental results show …

Investigation Of Filtering Methods For Large-Eddy Simulation, Weiyun Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis focuses on the phenomenon of aliasing and its mitigation with two explicit filters, i.e., Shuman and Padé filters. The Shuman filter is applied to velocity components of the Navier--Stokes equations. A derivation of this filter is presented as an approximation of a 1-D “pure math” mollifier and extend this to 2D and 3D. Analysis of the truncation error and wavenumber response is conducted with a range of grid spacings, Reynolds numbers and the filter parameter, β. Plots of the relationship between optimal filter parameter β and grid spacing, L²-norm error and Reynolds number to suggest …

A Metrics-Based Sustainability Assessment Of Cryogenic Machining Using Modeling And Optimization Of Process Performance, Tao Lu

Theses and Dissertations--Mechanical and Aerospace Engineering

The development of a sustainable manufacturing process requires a comprehensive evaluation method and fundamental understanding of the processes. Coolant application is a critical sustainability concern in the widely used machining process. Cryogenic machining is considered a candidate for sustainable coolant application. However, the lack of comprehensive evaluation methods leaves significant uncertainties about the overall sustainability performance of cryogenic machining. Also, the lack of practical application guidelines based on scientific understanding of the heat transfer mechanism in cryogenic machining limits the process optimization from achieving the most sustainable performance.

In this dissertation, based on a proposed Process Sustainability Index (ProcSI …

Lean Fire Management: A Focused Analysis Of The Incident Command System Based On Toyota Production System Principles, Jeremiah S. Fugate

Theses and Dissertations--Mechanical and Aerospace Engineering

A primary role of the Incident Command System is to learn from past incidents, as illustrated by its origins in the wildland firefighting community. Successful emergency response operations under the Incident Command System has prompted its nationwide spread, this promulgation critically relies on the system’s capability to stabilize and continuously improve various aspects of emergency response through effective organizational learning. The objective of this study is to evaluate the potential to apply fundamental principles of the Toyota Production System (Lean manufacturing) to improve learning effectiveness within the Incident Command System. An in-depth review of literature and training documents regarding both …

Experimental Studies On The Determination Of Acoustic Bulk Material Properties And Transfer Impedance, Wanlu Li

Theses and Dissertations--Mechanical and Aerospace Engineering

Soft trim absorbing parts (i.e., headliners, backwalls, side panels, etc.) are normally comprised of different layers including films, adhesives, foams and fibers. Several approaches to determine the complex wavenumber and characteristic impedance for porous sound absorbing materials are surveyed and the advantages and disadvantages of each approach are discussed. It is concluded that the recently documented three-point method produces the smoothest results. It is also shown that measurement of the flow resistance and the use of empirical equations is sufficient for many common materials. Following this, the transfer impedance of covers, adhesives, and densified layers are measured using an impedance …

Multidimensional Modeling Of Pyrolysis Gas Transport Inside Orthotropic Charring Ablators, Haoyue Weng

Theses and Dissertations--Mechanical and Aerospace Engineering

During hypersonic atmospheric entry, spacecraft are exposed to enormous aerodynamic heat. To prevent the payload from overheating, charring ablative materials are favored to be applied as the heat shield at the exposing surface of the vehicle. Accurate modeling not only prevents mission failures, but also helps reduce cost. Existing models were mostly limited to one-dimensional and discrepancies were shown against measured experiments and flight-data. To help improve the models and analyze the charring ablation problems, a multidimensional material response module is developed, based on a finite volume method framework. The developed computer program is verified through a series of test-cases, …

Fabrication Of Magnetic Two-Dimensional And Three-Dimensional Microstructures For Microfluidics And Microrobotics Applications, Hui Li

Theses and Dissertations--Mechanical and Aerospace Engineering

Micro-electro-mechanical systems (MEMS) technology has had an increasing impact on industry and our society. A wide range of MEMS devices are used in every aspects of our life, from microaccelerators and microgyroscopes to microscale drug-delivery systems. The increasing complexity of microsystems demands diverse microfabrication methods and actuation strategies to realize. Currently, it is challenging for existing microfabrication methods—particularly 3D microfabrication methods—to integrate multiple materials into the same component. This is a particular challenge for some applications, such as microrobotics and microfluidics, where integration of magnetically-responsive materials would be beneficial, because it enables contact-free actuation. In addition, most existing microfabrication methods …

Heat Transfer Characteristics In Wildland Fuelbeds, Justin English

Theses and Dissertations--Mechanical and Aerospace Engineering

The fundamental physics governing wildland fire spread are still largely misunderstood. This thesis was motivated by the need to better understand the role of radiative and convective heat transfer in the ignition and spread of wildland fires. The focus of this work incorporated the use of infrared thermographic imaging techniques to investigate fuel particle response from three different heating sources: convective dominated heating from an air torch, radiative dominated heating from a crib fire, and an advancing flame front in a laboratory wind tunnel test. The series of experiments demonstrated the uniqueness and valuable characteristics of infrared thermography to reveal …

Mathematical Model Of The Shell With The Infill For Retaining Structures, Alexander T. Bekker, Nikita Ya. Tsimbelman, Dmitriy A. Potyanikhin, Andrey I. Mamontov, Ömer Bilgin, Tatiana I. Chernova

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

A description of finite element model and analysis of a shell with an infill is performed. A large diameter thin cylindrical shell structure with the edge leaning against compressible foundation soil is analyzed. Different materials are considered individually for the models of each structure shell and infill component (metal or reinforced concrete shell, and granular or elastic infill in a shell and foundation soil loaded by the structure). Contact conditions between 1) the infill and the shell’s inner surface and 2) between the foundation material and the shell edge are analyzed. An example of calculating strain conditions in the shell …

Books And Our Human Stories, Paul H. Benson

Philosophy Faculty Publications

An essay on the impact of the works in the Imprints and Impressions: Milestones in Human Progress, an exhibition of rare books from the collection of Stuart Rose. Exhibition was held Sept. 29-Nov. 9, 2014, at the University of Dayton.

The Effects Of Narrative And Achievements On Learning In A 2d Platformer Video Game, Joseph Fanfarelli

Electronic Theses and Dissertations

Game design is a rigorous practice rife with complexity. The design of learning games is similarly complex to the design of their entertainment-based relatives. This complexity is partially due to the many interacting components that comprise games. The impacts of these individual components are not well understood. Advancing the understanding of how such component parts contribute to the formed game will inform decisions related to their inclusion and subsequent design within games. Achievements and narrative are two such components. They have been examined within gamified systems, but little research has studied them within the context of a serious game. The …

Practical Issues In Gpram Development, Yin Li

Electronic Theses and Dissertations

In this thesis, two parts of practical issues in the GPRAM system design are included. The first part is the coding part. The sum-product decoding algorithm of LDPC codes has been refined to fit for the GPRAM hardware implementation. As we all know, communication channel has noise. The noise in telecom system is different from that in GPRAM systems. So the noise should be handled well in the GPRAM design. A noise look-up table was created for FPGA and those noises in the table are quantized. The second part of the thesis is to convert perfect images in video stream …

Learning To Grasp Unknown Objects Using Weighted Random Forest Algorithm From Selective Image And Point Cloud Feature, Md Shahriar Iqbal

Electronic Theses and Dissertations

This method demonstrates an approach to determine the best grasping location on an unknown object using Weighted Random Forest Algorithm. It used RGB-D value of an object as input to find a suitable rectangular grasping region as the output. To accomplish this task, it uses a subspace of most important features from a very high dimensional extensive feature space that contains both image and point cloud features. Usage of most important features in the grasping algorithm has enabled the system to be computationally very fast while preserving maximum information gain. In this approach, the Random Forest operates using optimum parameters …

Load Transfer In An Isolated Particle Embedded Within An Epoxy Matrix, Erik Durnberg

Electronic Theses and Dissertations

Particulate composites are widely used in many aerospace applications such as protective coatings, adhesives, or structural members of a body and their mechanical properties and behavior have gained increasing significance. The addition of modifiers such as alumina generally leads to improved mechanical properties. This addition also enables the non-invasive study of the load transfer between the particle and the matrix. Understanding the load transfer between the particulate and the matrix material is the first step to understanding the behavior and mechanical properties of the composite as a whole. In this work, samples with an isolated alumina particle embedded in an …

Microstructure And Chemistry Evaluation Of Direct Metal Laser Sintered 15-5 Ph Stainless Steel, Kevin Coffy

Electronic Theses and Dissertations

15-5PH stainless steel is an important alloy in the aerospace, chemical, and nuclear industries for its high strength and corrosion resistance at high temperature. Thus, this material is a good candidate for processing development in the direct metal laser sintering (DMLS) branch of additive manufacturing. The chemistry and microstructure of this alloy processed via DMLS was compared to its conventionally cast counterpart through various heat treatments as part of a characterization effort. The investigation utilized optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-Ray diffractometry (XRD), energy dispersive X-Ray spectroscopy (EDS) and glow discharge atomic emission spectrometry (GDS) …

Taming Wild Faces: Web-Scale, Open-Universe Face Identification In Still And Video Imagery, Enrique Ortiz

Electronic Theses and Dissertations

With the increasing pervasiveness of digital cameras, the Internet, and social networking, there is a growing need to catalog and analyze large collections of photos and videos. In this dissertation, we explore unconstrained still-image and video-based face recognition in real-world scenarios, e.g. social photo sharing and movie trailers, where people of interest are recognized and all others are ignored. In such a scenario, we must obtain high precision in recognizing the known identities, while accurately rejecting those of no interest. Recent advancements in face recognition research has seen Sparse Representation-based Classification (SRC) advance to the forefront of competing methods. However, …

Modeling Repair Patches Of Ship Hull And Studying The Effect Of Their Orientation On Stresses, Halima Enwegy

Electronic Theses and Dissertations

The hull is the most important structural part of any maritime vessel. It must be adequately designed to withstand the harsh sailing environmental conditions and associated forces. In the past, the basic material used to manufacture the ship hull was wood, where the hull was usually shaped as cylindrical wooden shanks. In the present, hull designs have developed to steel columns or stiffened panels that are made of different types of materials. Panels that are stiffened orthogonally in two or more directions and have nine independent material constants are defined as orthotropic panels, and they achieve high specific strength. This …

The Effects Of Bam As An Adsorptive Media On Phosphorus Removal In Stormwater, Sultan Salamah

Electronic Theses and Dissertations

To maintain the quality of receiving water bodies, it is desirable to remove total phosphorus (TP) in stormwater runoff. Many media filtration technologies have been developed to achieve TP and soluble reactive phosphorus (SRP) removal. Efficient media adsorption is essential to insure control of stormwater phosphorus inputs to the receiving water body. This project develops and analyzes a functionalized Biosorption Media (BAM) to remove phosphorus species from stormwater runoff. One goal of this project is to find the BAM values for coefficients such as maximum adsorption capacity (QM: 4.35E-05) for the media through SRP isotherm equilibrium experiments using the Langmuir …