Engineering Commons^™

Influence Of Nanofiller Morphology On The Viscoelastic Properties Of Cnf/Epoxy Resins, Liberata Guadagno, Marialuigia Raimondo, Khalid Lafdi, Annalisa Fierro, Salvatore Rosolia, Maria Rossella Nobile

Chemical and Materials Engineering Faculty Publications

In this paper we discuss the viscoelastic properties of CNF/Epoxy-Amine Resins for structural applications. The use of reactive diluent inside the unfilled and nanofilled epoxy mixture as proven to be of benefit to strongly decrease the viscosity.

St. Jude Medical - R&D Robot For Sensor Testing, Andrew Chanul Kim, Stanley Logan Laszczyk, Edgar Nava, Nathan Gall

Electrical Engineering

No abstract provided.

Rapid Battery Exchange Safety And Sensing, Ben John Froelich, Isaac Sungjin Kim

Electrical Engineering

The Rapid Battery Exchange system (RBX) swaps batteries in an electric van, allowing almost continuous operation of the vehicle. The RBX system is designed and built by The Cal Poly Electric Vehicle Engineering Club (EVEC). The system includes the exchange ramp, two battery packs, and the electric “G-Van.” While the vehicle drives using one of the battery packs, the other pack charges in the exchange ramp. When the van’s battery depletes, it drives onto the ramp and swaps the dead battery for the charged one, and the process repeats.

The RBX battery pack safety and sensing project divides into two …

Battery Management System, Michael Desando, Kyle Woody

Electrical Engineering

Problem Statement:

There have been recent reports of multi-million dollar companies having to recall entire projects due to their BMS’s malfunctioning or operating incorrectly. The purpose of this project is to analyze the future of batteries, the Lithium-Ion cell, and to exercise a BMS to better understand its capabilities and possible cases for errors. Lithium ion batteries are intolerant of overcharge and overdischarge. Abuse of this kind can result in high temperatures, venting of gases, fire, or explosion. Therefore battery management systems have been devised to prevent such abuse. Recent events such as fires on the Boeing Dreamliner and the …

Low Voltage Cmos Sar Adc Design, Ryan Hunt

Electrical Engineering

This project centers on the design of a single ended 10-bit successive approximation register analog to digital converter (SAR ADC for short) that easily interfaces to a micro-controller, such as an Arduino. With micro-controller interfacing in mind, the universal data transfer technique of SPI proved an easy way to communicate between the ADC and the micro-controller. The ADC has a range of 1V (highest code value) to 0V (lowest code value) and operates from a single voltage rail value of 1.8V. Typical SPI clock speeds run on the order of 2MHz and with a 10-bit ADC this means a sampling …

Wind And Ventilation Turbine (Wvt) Generator, Anthony Lloyd, Jacob Michener

Electrical Engineering

This project aims to create a more compact and accessible renewable energy source using the Wind and Ventilation Turbine (WVT) Generator. The wind turbine provides ventilation while generating “clean” electricity using solar and kinetic energy. The electrical generation causes no functional losses to the ventilation as rising heat and passing wind turn the turbine, ventilating the house. Placing a generator beneath the spinning turbine allows for the transformation of mechanical motion into electrical energy. The system charges a battery, supplying recharging power into small standard electronics (i.e. cell phones, tablets, etc.) through a USB output.

Analog Violin Audio Synthesizer, Brandon E. Davis

Electrical Engineering

Abstract In the past decade, music electronics have almost completely shifted from analog to digital technology. Digital keyboards and effects provide more sound capabilities than their analog predecessors, while also reducing size and cost. However, many musicians still prefer analog instruments due to the perception that they produce superior sound quality. Many musicians spend extra money and accommodate the extra space required for analog technologies instead of digital.

Furthermore, audio synthesizers are commonly controlled with the standard piano keyboard interface. Many musicians can perform sufficiently on a keyboard, but requiring a specific skill set limits the size of the market …

Buck-Boost Dc-Dc Converter With Input Protection System For The Energy Harvesting From Exercise Machines Project, Byungjae David Yoo, Sheldon Tyler Kong Ming Chu

Electrical Engineering

Cal Poly’s Energy Harvesting from Exercise Machines (EHFEM) project comprises of multiple subprojects seeking to effectively create a sustainable energy source through harvesting electrical energy generated from physical exercise machines. This project designs and implements a Buck-Boost DC-DC converter using a LT3791-1 4-Switch Buck-Boost Controller, replacing the previous SEPIC design. The DC-DC converter must operate within limits set by the maximum input range of the LT3791-1 controller. An input protection system prevents inputs higher than rated values, which may adversely damage the Buck-Boost DC-DC converter. These inputs include overvoltage transients, average voltage, and current output by the Precor EFX 561i …

Real Time Swim Instructor, Konrad Antoniuk

Electrical Engineering

Both competitive and recreational swimmers want an efficient swim stroke but often lack consistent feedback with technical insight. Competitive swimmers rely on coaches for instruction but have to stop swimming to listen. The Real Time Swim Instructor project provides live feedback to a swimmer so they can feel their stroke correction while they’re swimming. The developing swimmer feels the difference between correct and incorrect form instantaneously.

The project takes on the responsibility of measuring the moving body, accurately determining stroke improvement, functioning under water, and providing recognizable feedback. Additionally, the user can review their swim from data stored in memory. …

Green Infrastructure, Sarah M. Mccormack, Roy E. Sturgill, Brian Howell, Christopher W. Van Dyke, Doug Kreis

Kentucky Transportation Center Research Report

The transportation industry has increasingly recognized the vital role sustainability serves in promoting and protecting the transportation infrastructure of the nation. Many state Departments of Transportation have correspondingly increased efforts to incorporate concepts of sustainability into the planning, design, and construction phases of projects and congruently adopted sustainability measures into their internal standard policies and procedures. Sustainably constructed highways foster economic development, promote stewardship of the environment, and solicit citizen involvement for an integrated, comprehensive approach to project planning. As part of an effort to understand the extent to which sustainable design and construction principles are being used, this report …

Simultaneous Measurement Of Temperature And Pressure With Cascaded Extrinsic Fabry-Perot Interferometer And Intrinsic Fabry-Perot Interferometer Sensors, Yinan Zhang, Jie Huang, Xinwei Lan, Lei Yuan, Hai Xiao

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents an approach for simultaneous measurement of temperature and pressure using miniaturized fiber inline sensors. The approach utilizes the cascaded optical fiber inline intrinsic Fabry-Perot interferometer and extrinsic Fabry-Perot interferometer as temperature and pressure sensing elements, respectively. A CO₂ laser was used to create a loss between them to balance their reflection power levels. The multiplexed signals were demodulated using a Fast Fourier transform-based wavelength tracking method. Experimental results showed that the sensing system could measure temperature and pressure unambiguously in a pressure range of 0 to 6.895 x 10⁵ Pa and a temperature range from …

Identifying Extract Class And Extract Method Refactoring Opportunities Through Analysis Of Variable Declarations And Uses, Mehmet Kaya

Dissertations - ALL

For small software systems, with perhaps a few thousand lines of code, software structure is largely an esthetic issue. When software systems grow large, including perhaps a million or more lines of source code, their structures become much more important.

Developing a large system requires teams of developers working in concert to provide a finished product in a reasonable amount of time. That means that many people will read each component to use, test or modify towards accomplishing new features.

In the software development life cycle, the maintenance phase is a dominant stage that impacts production cost of the system …

Relationship Between Jump Landing Kinematics And Peak Acl Force During A Jump In Downhill Skiing: A Simulation Study, D. Heinrich, Antonie J. Van Den Bogert, W. Nachbauer

Mechanical Engineering Faculty Publications

Recent data highlight that competitive skiers face a high risk of injuries especially during off-balance jump landing maneuvers in downhill skiing. The purpose of the present study was to develop a musculo-skeletal modeling and simulation approach to investigate the cause-and-effect relationship between a perturbed landing position, i.e., joint angles and trunk orientation, and the peak force in the anterior cruciate ligament (ACL) during jump landing. A two-dimensional musculo-skeletal model was developed and a baseline simulation was obtained reproducing measurement data of a reference landing movement. Based on the baseline simulation, a series of perturbed landing simulations (n=1000) was generated. Multiple …

Formula Sae Cooling System Design, Lisa Van Den Berg, Brandon Lofaro

Mechanical Engineering

The overall objective of this senior project is to develop, via testing and analysis, a guided process that will aid the Cal Poly Formula SAE team in designing their cooling system. More specifically, a set of designed tests will yield the results necessary in determining a combination of fan and radiator that will achieve appropriate cooling.

A test section that has the capability of interfacing with both the wind tunnel in the Thermal Science Lab and a radiator will be used to facilitate the necessary experiments. The wind tunnel is powered by fan controlled by a variable frequency drive that …

Formula Sae Hybrid Carbon Fiber Monocoque / Steel Tube Frame Chassis, Matthew Hagan, John Rappolt, John Waldrop

Mechanical Engineering

The Cal Poly Formula SAE Team created this project in order to design and fabricate a high-performance chassis which would be competitive at 2013 FSAE Lincoln, and to document the process so that future teams could more easily create a chassis. One of the main goals was to reduce weight from the 143- lb 2012 chassis subsystem. A weight of 95 lb was achieved, with 82 lb in the chassis structure itself and a predicted torsional stiffness of 1700 lb*ft/deg. Composite materials design and manufacturing techniques were developed during the project. Design, testing, and manufacturing processes are detailed, and results …

Horned Lark Management For The Protection Of Lettuce Sprouts, Taylor Wetzel, Eduardo Morales, Kyle Suguitan

Mechanical Engineering

The following document is the Final Project Report. Following the Critical Design Report, the top idea was taken and modified once again to suit the needs of the sponsor. Details regarding the changes are outlined throughout Chapter 3.

The provided background section explains why there is a need for a new device at Tanimura and Antle that will suit the customer's needs better than current methods and existing products. The top ideas picked for the Conceptual Design Review are the presented to reiterate the problems that were depicted in them and why they were not selected as part of the …

Low-Cost Strider For Guatemala, Nicole Catherine Cooper, Gonzalo Hernandez, Jared W. Tower

Mechanical Engineering

The purpose of this project was to create a strider, a type of standing rehabilitation device, for children in developing countries who have trouble walking and supporting their full body weight. The project was initially brought to us by Cal Poly professor Brian Self, who had visited a clinic in San Marcos and determined that there were children there who had difficulties with walking and were a need for a rehabilitation device. The team discussed the problem with Dr. Self, Matt Robinson (a local San Luis Obispo prosthetist), and Cal Poly physics professor Pete Schwartz, all of whom had visited …

Energy Generator Exploration Station Senior Project Report, Evan Carr, Christopher Scharff, Andrea Govea

Mechanical Engineering

The mission of Team EnGen is to create a safe and reliable, human powered energy generation system for the Exploration Station. This project was proposed by the Exploration Station in response to a grant received by Pacific Gas and Electric (PG&E) that allocated funds for an energy conservation exhibit. This system will take the form of a model energy truck and a darkened neighborhood display that the user powers through peddling, turning the generator to create the electricity that will light up the display. The Exploration Station and Team EnGen agree that this style of design is accessible to all …

2d Wireform Process Improvement, Katy Conlin, Carlo Ebora, Jordan Gamble

Mechanical Engineering

The body of this work has been created for Edwards Lifesciences in conjunction with senior project requirements. As such, the information produced and contained within is under a non‐disclosure agreement. As per request by sponsor, the body of the work will not be submitted to any outside parties, and the title page will serve as proof of completion.

Automated Foosball Table, Jim R. Stefani, Alex J. Herpy, Brett Gordon Jaeger, Kevin S. Haydon, Derek Alan Hamel

Mechanical Engineering

This project is the second iteration of an automated foosball table for Yaskawa America as a trade show display. The table is meant to provide an interactive experience which highlights the speed and precision of the Yaskawa hardware. The first iteration of the project was mainly focused on creating the physical hardware for the system and to begin the basic programming for the system. This phase of the project was focused on finalizing the physical hardware of the system, implementing the vision system and to continue the basic programing of the system AI. A third team will be assigned to …

Adaptive Beach Walker, Jonathan Larsen, Christian Nuñez, Nicholas Simon, Jessica Smith

Mechanical Engineering

The RAPD program is a federal organization funded by the National Science Foundation that supports the development of technologies for new and improved devices or software for persons with disabilities; in the case of our project and our fellow classmates, the program provided grants to student projects that are designed to help persons with disabilities in participating and enjoying physical activity. Our project is directed with the help of Dr. Widmann and Dr. Taylor of the Mechanical Engineering and Kinesiology Departments respectively, at California Polytechnic State University, San Luis Obispo. Three students from the Mechanical Department and one student from …

Mobile Solar Pv Trainer, Matthew Myers, Matthew Clause, Lawrence Smith

Mechanical Engineering

The aim of the Mobile Solar PV Trainer Project was to design, construct and test a versatile and robust laboratory training rig for the Cal Poly Electrical Engineering department. This project was inspired by the desire of one or more California Polytechnic State University electrical engineering professors to add laboratory components to two established upper division electrical engineering courses in photovoltaic panels and solar power. This report contains a detailed description of the trainer’s desired specifications, our ideation process, a thorough description of the selected trainer design including part drawings, assembly documentation and a bill of materials as well as …

Adaptive Adjustable Tricycle, Jasper E. Bolton, Kemely A. Chow, Ryan D. Hirahara, Heather K. Instasi

Mechanical Engineering

As a part of the Cal Poly Mechanical Engineering curriculum, all students must take part in a three quarter long senior design project. Students are presented with existing problems, select a project, and then apply the knowledge they have gained throughout their academic career to design and build a solution. The intent behind this project is to create an experience that is similar to an engineering project in industry, by applying engineering and teamwork skills to solve a problem.

Team Trikeceratops’ mission was to develop an adaptive adjustable tricycle to be used in the Special Education Department of the Buena …

Mini-High Temperature Hepa Filter Test Unit, Mario Trinchero, Juan Miguel Nagengast, Andrew Wood

Mechanical Engineering

There is a need for better HEPA filter materials, especially those able to withstand higher temperatures as experienced in fire conditions. In order to test these materials our team built a Mini High Temperature Testing Unit (MHTTU) that can rapidly, efficiently, and inexpensively test a large number of new and innovative materials for HEPA filter components. MHTTU test results will be used to down select the most promising materials for HEPA filter components (e.g., media, sealants, gaskets) for full scale testing in the HTTU. There are already some pieces of equipment that exist in other parts of the country that …

Design And Analysis Of The Brae Tractor Pull Tow Vehicle, Alexander R. Paulsen

BioResource and Agricultural Engineering

This senior project discusses the design and analysis of a towing vehicle for the tractor pulling team and the BRAE department. This report examines different types of existing hand operated towing vehicles and their strengths and weaknesses and how they can be modified to design a custom tow vehicle for the BRAE department. The purpose of this report was to make transporting and handling of the modified pulling tractors in the BRAE department safer for the operator and bystanders.

Atv Mountable Tree Planting Station, Bradley M. Rogers

BioResource and Agricultural Engineering

No abstract provided.

Design And Evaluation Of An Irrigation Storage Reservoir, James Tomac

BioResource and Agricultural Engineering

No abstract provided.

Modification Of A Draw Bar Type Arena Harrow To Three Point Mounted Type Harrow, Clayton Alan Brown

BioResource and Agricultural Engineering

This senior project will be the design, and construction of a three point hitch to be attached to a draw bar type spike tooth harrow. Currently used by the Cal Poly Rodeo Team to cultivate their arena before performances, and practices.

The attachment will allow the harrow to be pulled in both directions to create different types of soil affects.

Also the fabrications has a minimal budget so the majority of the materials will be scrap material already in position of the rodeo team or donated to the project.

Design, Construction, And Evaluation Of An Rc Vehicle Dynamometer, Christian Marron

BioResource and Agricultural Engineering

No abstract provided.

Electroplating Of Nanoengineered Polymer Substrate, Brandon Voelker

Masters Theses

The development of a polyethylene based polymer with metallic inclusions, a nanoengineered polymer, has recently opened up great potential for many new commercial and industrial applications. The major advantage of developing these nanoengineered polymers is to be able to tailor the resistance and other properties by varying the composition of the polymer. The industrial usage of this polymer benefits from the addition of an electrically conductive, metallic coating. This research develops methods of electroplating nickel and copper layers on to the polymer substrates using DC and pulsed techniques.

Electroplating is conducted in a 1000 mL beaker using a specialized plating …