Engineering Commons^™

Rapid Repair Of Severely Damaged Rc Columns With Different Damage Conditions: An Experimental Study, Ruili He, Lesley Sneed, Abdeldjelil Belarbi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Performance Enhancement Of Crumb Rubber-Modified Asphalts Through Control Of The Developed Internal Network Structure, Mohyeldin Ragab, Magdy Abdelrahman, Amir Ghavibzaoo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Control of the internal network structure of crumb rubber-modified asphalt (CRMA) was investigated for its effect on property development in the study presented in this paper. The investigation included evaluation by rheological and interrupted shear tests. Rheological testing involved the monitoring of the changes of the produced complex modulus (G*) and phase angle (δ) for CRMA. In the interrupted shear tests, the shear stress profile for the produced CRMA was investigated. It was found that triggering the critical conditions of the combined interaction of speed, temperature, and time was essential to inducing the formation of the three-dimensional network …

Consensus Protocols In Networked Multiagent Systems For Cluttered And Hostile Environments, Gerardo De La Torre, Eric N. Johnson, Tansel Yucelen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Consensus refers to the agreement of networked agents upon certain quantities of interest and has widespread applications in diverse areas in science and engineering. This paper focuses on a new consensus protocol for networked multiagent systems operating in cluttered and hostile environments. Specifically, a consensus optimization algorithm is introduced that renders the Laplacian potential to be a nonincreasing function while minimizing a cost function and satisfying state and cost constraints. In addition, we show how to choose this cost function and the aforementioned constraints in order to decay the Laplacian potential to zero strictly. The proposed framework depends on a …

Neuropredictive Control And Trajectory Generation For Slung Load Systems, Gerardo De La Torre, Eric N. Johnson, Tansel Yucelen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a neuropredictive trajectory generation architecture for slung load systems. The presented architecture integrates the real-time trajectory generation method with a system uncertainty identifying neural network. It is shown that the effect of system uncertainty on a model predictive control approach can be mitigated by the use of neural networks. A numerical example of an uncertain slung load system is shown to demonstrate the effectiveness of the presented framework.

Consensus Protocols For Networked Multiagent Systems With Relative Position And Neighboring Velocity Information, Gerardo De La Torre, Tansel Yucelen, Eric N. Johnson

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The consensus problem appears frequently in the coordination of multiagent systems in science and engineering and involves the agreement of networked agents upon certain quantities of interest. In this paper, we focus on a new consensus protocol for networked multiagent systems. The proposed control protocol consists of a standard term capturing relative position information and a new term capturing neighboring velocity information. In particular, the addition of the latter term results in an increase of the rate of system convergence while maintaining a fixed graph structure and without increasing the maximum eigenvalue of the graph Laplacian. Furthermore, in certain cases, …

Constraint Enforcement Methods For Command Governor Based Adaptive Control Of Uncertain Dynamical Systems, Simon P. Schatz, Tansel Yucelen, Eric N. Johnsony, Florian Holzapfelz

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Recently, research has been conducted in order to improve the transient behavior of adaptively controlled uncertain nonlinear dynamical systems. In this paper, an adaptive control architecture is extended in order to achieve predictable transient performance in the presence of state constraints. The methodology at hand is based on a robust command governor framework, which is a dynamical system adjusting the trajectory of a given command in order to track a certain desired closed-loop reference model both in transient time and steady-state. Specifically, the command, which is applied on the reference model and the actual system, is changed by the command …

Scale Of Fluctuation Of Geotechnical Parameters Estimated From Cptu And Laboratory Test Data, Site Onyejekwe, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

For a complete probabilistic characterization of a geotechnical parameter, its mean, variance, and the scale of fluctuation have to be known. While the mean and variance can be easily determined, determination of the scale of fluctuation is a little more complex. Knowledge of the scale of fluctuation is important in reliability-based design as it is used in implementing spatial averaging and computing the variance-reduction factor. Published values of scale of fluctuation of geotechnical parameters are based on widely sourced data and hence may not be most appropriate for local situations. Based on 11 CPTu soundings and laboratory test results of …

Product Characterization And Headspace Analysis Of Solar Irradiated Aqueous C60 Clusters, Dan Su

Open Access Theses

Buckminsterfullerene (C60) is an important fullerene material that has drawn much attention and is currently being applied in many different fields. It was discovered in 1985. As its production has largely increased to meet these industrial needs, it is obvious that its environmental occurrence, especially in aqueous systems, will occur. To further provide information for environmental toxicity studies and for its risk assessment, this thesis focuses on the photo transformation processes of aqueous C60 clusters (Aqu/nC60), with a particular interest in measuring any mineralization that occurs under different irradiation conditions. Two sets of experiments were conducted to test for CO2 …

Determination Of Heat Transfer In Under-Floor Plenums In Buildings With Under-Floor Air Distribution Systems, Yan Xue

Open Access Theses

Under-Floor Air Distribution (UFAD) systems have potential advantages of energy saving and indoor air quality improvement over conventional well-mixed systems. As a ventilation strategy for buildings, a UFAD system provides conditioned air to occupied rooms through diffusers in raised floors and the air is exhausted through return grilles at the ceiling level.

Many previous researches have focused on the energy saving and air quality improvement by UFAD systems because of their high supply air temperature and room air stratification. However, few of them paid attention to the effects of the heat transfer through floor slabs on the energy performance of …

Effect Of Process Parameters On The Weld Quality In Laser Welding Of Az31b Magnesium Alloy In Lap Joint Configuration, Masoud Harooni, Blair Carlson, Radovan Kovacevic

Mechanical Engineering Research

Magnesium is the lightest structural metal; therefore it has been used in a variety of industries such as automotive, aerospace, electronics and defense. Among different joining processes, laser welding is advantageous due to its low heat input, high depth-to-width weld ratio and good mechanical properties. In this study, a fiber laser is used to weld AZ31B magnesium alloy in a lap joint configuration. Pores were formed in the weld bead that are caused by a thick oxide layer existing on the surface of as-received AZ31B samples. Process parameters including laser power and welding speed are studied to determine their effects …

Trajectory Generation For Stair Ascent Walking Using Rayleigh Oscillator, T. Afzal, Andrew B. Wright, Kamran Iqbal

Journal of the Arkansas Academy of Science

This paper describes a trajectory generation technique for stair-ascent walking. The knee, hip and ankle joint trajectory during stair ascent are generated using mutually coupled, nonlinear oscillators. The parameters of the oscillators are tuned using the harmonic balance method, which converts the nonlinear differential equations to a set of algebraic equations. Fourier analysis of data generated by stair-ascent walking is performed to extract the amplitude and the phase of the dominant frequency components for each joint trajectory. The solution for the oscillator is assumed to be a sinusoidal wave and then by harmonic balance method the parameters of the oscillator …

Large Eddy Simulation And Analysis Of Shear Flows In Complex Geometries, Prasad Mohanrao Kalghatgi

LSU Doctoral Dissertations

In the present work, large eddy simulation is used to numerically investigate two types of shear flows in complex geometries, (i) a novel momentum driven countercurrent shear flow in dump geometry and (ii) a film cooling flow (inclined jet in crossflow). Verification of subgrid scale model is done through comparisons with measurements for a turbulent flow over back step, present cases of counter current shear and film cooling flow. In the first part, a three dimensional stability analysis is conducted for countercurrent shear flow using Dynamic mode decomposition and spectral analysis. Kelvin-Helmholtz is identified as primary instability mechanism and observed …

Development Of A Framework For Scaling Surfactant Enhanced Co₂ Flooding From Laboratory Scale To Field Implementation, Gbolahan I. Afonja

LSU Doctoral Dissertations

The efficiency of the use of CO2 as a displacement fluid in oil recovery is hampered by the existence of an unfavorable mobility ratio that is caused by the large difference in viscosity between the injected fluid (CO2) and the reservoir fluids. This viscosity contrast results in early CO2 breakthrough, viscous fingering, gas channeling, and consequently, the inability of CO2 to effectively contact much of the reservoir and the oil it contains. Improvement of sweep efficiency and mobility control in CO2 injection require solutions to these problems. The use of surfactants and other chemical means for mobility control has been …

Investigations Of The Effects Of Flame Configuration On The Combustion Of Laminar Diffusion Flame, Li Lu

LSU Doctoral Dissertations

Motivation and objective to study double inverse diffusion flame is introduced, followed by the literature survey on soot formation in inverse diffusion flame (IDF), application of the unique structure of double inverse diffusion flame (DIDF), radiation effects on DIDF, factors that affect the formation of nitric oxide and effects of elevated pressure on diffusion flames. Numerical method is validated by the result of flame height for IDF, which is consistent with result from previous research. In present work, two DIDF burner configurations with different size are used to conduct the simulation. Ethylene is used as the fuel. For each of …

3d Integration Of Micro- And Nanostructures Into Bio-Analytical Devices, Bahador Farshchian

LSU Doctoral Dissertations

This study aims to develop a process which allows 3D integration of micro and nanostructures in microchannels. A fabrication process was established for the large area integration of hierarchical micro and nanostructures in microchannels. This novel process, which is called 3D molding, takes advantage of an intermediate thin flexible stamp such as PDMS from soft lithography and a hard mold such as brass from hot embossing process. However, the use of a thin intermediate polydimethylsiloxane (PDMS) stamp inevitably causes dimensional changes in the 3D molded channel, with respect to those in the brass mold protrusion and the intermediate PDMS stamp …

Nanotube Film-Enhanced 3-D Photoanode For Application In Microsystems Technology, Fareed Dawan

LSU Doctoral Dissertations

Surface area plays an important factor in the energy conversion performance of solar cells. It has also emerged as a critical factor in the evolution of high-performance micro-electro-mechanical systems (MEMS) and multifunctional microstructures most of which will benefit from integrated on-chip solar power. Presented here is the hierarchical fabrication and characterization of TiO2 nanotubes on non-planar 3-dimensional microstructures for enhanced performance of the photoanode in dye-sensitized solar cells (DSSCs). The objective is to increase photoanode performance within a 1 cm2 lateral footprint area by increasing the vertical surface area through the formation of TiO2 nanotubes on 3-D microstructures. In the …

Cpg And Interleukin-15 Synergize To Enhance Ifn-Gamma Production By Activated Cd8(+) T Cells, Dustin Cobb, Sigi Guo, Ronald B. Smeltz

Bioelectrics Publications

Interleukin-15 (IL-15) regulates the development and maintenance of memory CD8(+) T cells. Paradoxically, we previously reported that IL-15 could enhance CD8(+) T-cell responses to IL-12, a proinflammatory cytokine required for optimal priming of effector CD8(+) T cells. To expand the physiological relevance of these findings, we tested IL-15 for its ability to enhance T-cell responses to bacterial CpG. Expectedly, CpG enhanced the production of IFN-gamma by CD8(+) T cells polyclonally activated with anti-CD3. However, addition of IL-15 to CpG-stimulated cultures led to a striking increase in IFN-gamma production. The effect of CpG and IL-15 was also evident with CD8(+) T …

Induction Of Cell Death Mechanisms And Apoptosis By Nanosecond Pulsed Electric Fields (Nspefs), Stephen J. Beebe, Nova M. Sain, Wei Ren

Bioelectrics Publications

Pulse power technology using nanosecond pulsed electric fields (nsPEFs) offers a new stimulus to modulate cell functions or induce cell death for cancer cell ablation. New data and a literature review demonstrate fundamental and basic cellular mechanisms when nsPEFs interact with cellular targets. NsPEFs supra-electroporate cells creating large numbers of nanopores in all cell membranes. While nsPEFs have multiple cellular targets, these studies show that nsPEF-induced dissipation of DeltaPsim closely parallels deterioration in cell viability. Increases in intracellular Ca2+ alone were not sufficient for cell death; however, cell death depended of the presence of Ca2+. When both events occur, cell …

Atomic Force Microscopy Characterization Of Collagen ‘Nanostraws’ In Human Costal Cartilage, Michael W. Stacey, Diganta Dutta, Anthony Asmar, H. Elsayed-Ali, R. Kelly Jr., A. Beskok

Bioelectrics Publications

Costal cartilage, a type of hyaline cartilage that bridges the bony ribs and sternum, is relatively understudied compared to the load bearing cartilages. Deformities of costal cartilage can result in deformation of the chest wall, where the sternum is largely pushed toward or away from the spine, pectus excavatum and pectus carinatum, respectively, with each condition having significant clinical impact. In the absence of extensive literature describing morphological features of costal cartilage, we characterized a sample from the costal margin immunohistologically and through atomic force microscopy. We had previously observed the presence of collagen ‘nanostraws’ running the length of costal …

Impulsivity Like Traits And Risky Driving Behaviors Among College Students, Matthew R. Pearson, Elaine M. Murphy, Ashley N. Doane

Psychology Faculty Publications

The present study examined the predictive effects of five impulsivity-like traits (Premeditation, Perseverance, Sensation Seeking, Negative Urgency, and Positive Urgency) on driving outcomes (driving errors, driving lapses, driving violations, cell phone driving, traffic citations, and traffic collisions). With a convenience sample of 266 college student drivers, we found that each of the impulsivity-like traits was related to multiple risky driving outcomes. Positive Urgency (tendency to act impulsively when experiencing negative affect) was the most robust predictor of risky driving outcomes. Positive Urgency is a relatively newly conceptualized impulsivity-like trait that was not examined in the driving literature previously, suggesting a …

Primary Pathways Of Intracellular Ca2+ Mobilization By Nanosecond Pulsed Electric Field, Iurii Semenov, Shu Xiao, Andrei G. Pakhomov

Bioelectrics Publications

Permeabilization of cell membranous structures by nanosecond pulsed electric field (nsPEF) triggers transient rise of cytosolic Ca²⁺ concentration ([Ca²⁺]_i), which determines multifarious downstream effects. By using fast ratiometric Ca²⁺ imaging with Fura-2, we quantified the external Ca²⁺ uptake, compared it with Ca²⁺ release from the endoplasmic reticulum (ER), and analyzed the interplay of these processes. We utilized CHO cells which lack voltage-gated Ca²⁺ channels, so that the nsPEF-induced [Ca²⁺]_i changes could be attributed primarily to electroporation. We found that a single 60-ns pulse caused fast [Ca2+]_i increase …

Response To "Sodium Current Inhibition By Nanosecond Pulsed Electric Field (Nspef) - Fact Or Artifact?" By Verkerk Et Al, Andrei G. Pakhomov

Bioelectrics Publications

It was nice to learn that our studies of nanosecond pulsed electric field (nsPEF) effects on membrane currents [Nesin et al., 2012; Nesin and Pakhomov, 2012] gained the attention of scientists outside the immediate field of bioelectromagnetics.

Recruitment Of The Intracellular Ca2+ By Ultrashort Electric Stimuli: The Impact Of Pulse Duration, Iurii Semenov, Shu Xiao, Olga N. Pakhomova, Andrei G. Pakhomov

Bioelectrics Publications

Nanosecond-duration electric stimuli are distinguished by the ability to permeabilize intracellular membranes and recruit Ca²⁺ from intracellular stores. We quantified this effect in non-excitable cells (CHO) using ratiometric Ca²⁺ imaging with Fura-2. In a Ca²⁺-free medium, 10-, 60-, and 300-ns stimuli evoked Ca2⁺ transients by mobilization of Ca²⁺ from the endoplasmic reticulum. With 2 mM external Ca²⁺, the transients included both extra- and intracellular components. The recruitment of intracellular Ca²⁺ increased as the stimulus duration decreased. At the threshold of 200–300 nM, the transients were amplified by calcium-induced calcium release. We …

The Effect Of Sensor Mass, Sensor Location, And Delamination Location Of Different Composite Structures Under Dynamic Loading, Albert Darien Liu

Master's Theses

This study investigated the effect of sensor mass, sensor location, and delamination location of different composite structures under dynamic loading. The study pertains to research of the use of accelerometers and dynamic response as a cost-effective and reliable method of structural health monitoring in composite structures. The composite structures in this research included carbon fiber plates, carbon fiber-foam sandwich panels, and carbon-fiber honeycomb sandwich panels. The composite structures were manufactured with the use of a Tetrahedron MTP-8 heat press. All work was conducted in the Cal Poly Aerospace Structures/Composites Laboratory. Initial delaminations were placed at several locations along the specimen, …

A Comparative Study Of The Dry And Wet Nano-Scale Electro-Machining, M. P. Jahan, K. R. Virwani, Kamlakar P. Rajurkar, A. P. Malshe

Department of Mechanical and Materials Engineering: Faculty Publications

In recent years, a nano-electromachining (nano-EM) process based on a scanning tunneling microscope (STM) platform has been demonstrated. Nano-EM is capable of machining nano-features, under both, liquid dielectric (wet nano-EM) and air dielectric (dry nano-EM) media. The objective of this paper is to present a comparative study between the wet and dry nano-EM processes based on process mechanism, machining performance, consistency and dimensional repeatability of these two processes. The comparison of the two processes has been conducted at near field nano-EM, where the gap between the tool electrode and workpiece is 2 nm and the machining is performed at room …

Inducing Neurite Outgrowth By Mechanical Cell Stretch, Suzanne Higgins, Jeong Soon Lee, Ligyeom Ha, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Establishing extracellular milieus to stimulate neuronal regeneration is a critical need in neuronal tissue engineering. Many studies have used a soluble factor (such as nerve growth factor or retinoic acid [RA]), micropatterned substrate, and electrical stimulation to induce enhanced neurogenesis in neuronal precursor cells. However, little attention has been paid to mechanical stimulation because neuronal cells are not generally recognized as being mechanically functional, a characteristic of mechanoresponsive cells such as osteoblasts, chondrocytes, and muscle cells. In this study, we performed proof-of-concept experiments to demonstrate the potential anabolic effects of mechanical stretch to enhance cellular neurogenesis. We cultured human neuroblastoma …

Systems Biology Of The Functional And Dysfunctional Endothelium, Jennifer Frueh, Nataly Maimari, Takayuki Homma, Sandra M. Bovens, Ryan M. Pedrigi, Leila Towhidi, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

This review provides an overview of the effect of blood flow on endothelial cell (EC) signalling pathways, applying microarray technologies to cultured cells, and in vivo studies of normal and atherosclerotic animals. It is found that in cultured ECs, 5–10% of genes are up- or down-regulated in response to fluid flow, whereas only 3–6% of genes are regulated by varying levels of fluid flow. Of all genes, 90%are regulated by the steady part of fluid flow and 10% by pulsatile components. The associated gene profiles show high variability from experiment to experiment depending on experimental conditions, and importantly, the bioinformatical …

Assessing Safety Culture Within A Flight Training Organization, David Freiwald, Carolina Lenz-Anderson, Erik Baker

Applied Aviation Sciences - Daytona Beach

This study was prompted by a string of aircraft hull losses experienced by a multinational, multi-campus flight training organization. A mixed methods study was conducted to study the attitudes and perceptions of the operations and management staff at this flight training organization through the use of a survey instrument previously existing and adapted, in order to ensure validity, and interviews with key staff members. Confirmatory factor analysis was performed to identify underlying constructs in the perceptions and attitudes of the staff in order to identify beliefs that may signify a flight training organization is at risk. An analysis was conducted …

Degradable Plastics And Solid Waste Management Systems, David J. Tonjes, Krista L. Thyberg

Technology & Society Faculty Publications

Plastics, which are woven into the fabric of modern life, have consequential impacts on the environment. Many of these are associated with end-of-lifetime processes, and include chemical contamination of the environment and effects from litter. Plastics also complicate waste management processes, causing contamination in composting operations, and having poor recovery rates through recycling. Plastics that are not as biologically recalcitrant, that decompose when use is done, have been perceived as solutions to at least some of these problems. The first generation of degradable plastics did not meet marketing claims; some of the more recent formulations, partly as a consequence of …

Municipal Waste Management: Suffolk County Municipal Systems, Services And Infrastructure, Krista L. Greene, Susan Lienau, David J. Tonjes

Technology & Society Faculty Publications

This report describes the municipal waste management systems used by local governments to manage solid waste in Suffolk County, Long Island, New York. There are ten Towns that serve as the primary planners for waste systems in Suffolk County. Many of the 33 villages in Suffolk County have established their own waste management programs and policies. All programs tend to follow the same general plan of the approaches used by their respective Towns, however. All programs provide some degree of recycling services, although the scope of the services varies tremendously.