Engineering Commons^™

Management Feasibility Of Solar Energy Capture System In A Poultry Production Facility, Dan Leitcher

BioResource and Agricultural Engineering

This senior project involves designing a solar system for an agriculture entity and conducting a feasibility management study on the system. The feasibility study will look the initial cost, amount of energy generated, and estimated payback of the system. These factors will determine whether or not the Cal Poly poultry unit should ever implement solar into their operations. It will be ideal if the designed system can generate enough power to cover the electric usage associated. The system can be either photovoltaic or thermal and could either be a ground or roof mount system. The agriculture entity selected was the …

Design, Constuction, And Evaluation Of A Flame Cultivator Attachment, Aaron Evans

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and testing of a flame cultivator attachment. The project used existing torches, a tractor, and a cultivation sled to increase the usability of the farmer’s torches. This project includes two torch clamps, two propane tank brackets, and a removable valve panel. Testing showed that the new system increases the safety and efficiency of the torches.

Practical Irrigation Scheduling Program, Dominic Sween

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and evaluation of an irrigation scheduling program that aids users in alfalfa irrigation management, with the potential for application with other crops. The program uses a very accurate irrigation prediction model that forecasts what the estimated irrigation need of each week will be, as well as the number of irrigations needed to satisfy the requirement. The model was found to predict the sum of the actual required weekly irrigation amount within less than 1% of the true value. The program was based off the single crop coefficient approach that was outlined previously by …

Design Of Vineyard Irrigation System And Reservoir Enlargement, Matthew M. Moore

BioResource and Agricultural Engineering

The goal of this project is to design a drip irrigation system for a 25 acre vineyard in Potter Valley, Ca. This allows water to be efficiently delivered to the plants in a timely manner in order to maximize yield or fruit quality. This design will also include the resizing of the current reservoir in order to accommodate for the new water requirements; however this design will not include the overhead sprinkler system needed for frost protection.

We Still Need A Real-Time Hemodynamic Monitor For Cpr, Charles F. Babbs

Weldon School of Biomedical Engineering Faculty Publications

No abstract provided.

Using Discrete Event Simulation To Improve The Patient Care Process In The Emergency Department Of A Rural Kentucky Hospital., Molly Cassaro Jones

Electronic Theses and Dissertations

The patient care process of a rural Kentucky hospital is a complex process that must be flexible in order to deal with a large variety of patient needs and a fluctuating patient volume where all patients are unscheduled. A simulation model of an average month in the emergency department was built using the Arena Simulation package. Methods for creating a simulation using Arena are included in this work. Statistics were generated from a number of different sources to create an accurate representation of the model. The Hospital reporting shows a need to improve on two quality measures being tracked, the …

Fpga Hardware Accelerators - Case Study On Design Methodologies And Trade-Offs, Matthew V. Ryan

Theses

Previous research has shown that the performance of any computation is directly related to the architecture on which it is performed. As a result, the performance of compute intensive applications can be improved using heterogeneous systems. These systems consist of various processor architectures such as CPU, FPGA, DSP, and GPU. Individual computations can be performed in parallel on different processor architecrues within the heterogeneous system. Computations are performed by utilizing existing designs from implementation libraries. There is a lack of FPGA accelerators for use in these libraries and as such additional implementations need to be designed.

Different design methodologies for …

Starting A Construction Engineering Program At Marquette University, Mark O. Federle

Civil and Environmental Engineering Faculty Research and Publications

Marquette University decided to start a Construction Engineering and Management program during the 2007 academic year. An endowed chair, titled the McShane Chair in Construction Engineering and Management, was funded by Jim and Kelly McShane to run the program. After a national search, Mark Federle, an executive with a large construction firm and previous academic experience at Iowa State University, was hired to start the program. The first class of students were enrolled in the fall of 2008. This paper will present the opportunities/challenges in starting a Construction Engineering and Management program. Lessons learned, comparisons to other programs, and other …

Path Loss In An Urban Peer-To-Peer Channel For Six Public-Safety Frequency Bands, David W. Matolak, Qian Zhang, Qiong Wu

Faculty Publications

We provide path loss data and models for a peer-to-peer wireless channel for an urban environment in six public safety bands, for simultaneous transmission to five spatially separated receiving sites. Results are from measurements in Denver, Colorado. The six frequencies at which we measured are (in MHz) 430, 750, 905, 1834, 2400, and 4860. Both line-of-sight and non-line-of-sight conditions were covered, and we quantify path loss exponents and linear-fit standard deviations as functions of frequency and location. Line-of-sight results agree with prior work, but non-line-of-sight exponents, from 3.6-7.3, are generally larger than in most other references.

Experimental Assessment Of The Impact Of Asymptomatic Gas Emboli On The Vessel Wall, Linxia Gu, Eric L. Cutler

Department of Mechanical and Materials Engineering: Faculty Publications

Quantitative evaluation of shear stress in the vessel wall due to the presence of asymptomatic gas emboli is lacking. The goal of this work was to assess the impact of chronic asymptomatic gas emboli on the risk of atherosclerosis through a custom-built cardiovascular flow simulator. Gas bubbles were created by forced air from a syringe pump. The influences of embolism injection rate, pulse rate, and time-averaged flow rate on the wall mean shear stress were investigated at resting and elevated heart rate conditions. The recorded pressure and volumetric flow rate from 24 experimental settings with four repetitions each were used …

Laboratory Evaluation Of A Turn Compensation Control System For A Ground Sprayer, Wesley M. Porter, Jorge A. Rascon, Yeyin Shi, Randal K. Taylor, Paul A. Weckler

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The ability to compensate sprayer nozzle flow across a horizontal boom has the potential to mitigate the problem of inaccurate chemical application rate due to lateral speed differences when sprayers are turning. A laboratory testing platform and procedure were developed and tested with a commercial turn compensation control system for a ground sprayer. Virtual paths consisting of simulated GPS signals representing right and left turns separated by straight segments were simulated with four turning radii (75%, 125%, 250%, and 500%) based on boom width. Actual application rates from 11 nozzles spread across the boom were measured using load cells in …

Multiplicative Feedback Audio Distortion Circuit, Colton Parsons

Electrical Engineering

This circuit aims to distort an audio signal input in a novel and aesthetically pleasing manner. When it comes to the timbre of a note, even harmonics generally sound better than odd harmonics. Most forms of audio signal distortion (usually for electric guitar) primarily add odd harmonics to a signal, as this is easily accomplished by clipping the waveform. This project instead utilizes a signal multiplier in a feedback loop, with one multiplier input coming from the circuit’s input, and the other from the multiplier’s own output. This process creates even harmonics. A delay line is placed in the loop, …

Reconfigurable Threshold Logic Gates Using Memristive Devices, Adrian Rothenbuhler, Thanh Tran, Elisa H. Barney Smith, Vishal Saxena, Kristy A. Campbell

Electrical and Computer Engineering Faculty Publications and Presentations

We present our design exploration of reconfigurable Threshold Logic Gates (TLG) implemented using silver–chalcogenide memristive devices combined with CMOS circuits. Results from simulations and physical circuits are shown. A variety of linearly separable logic functions including AND, OR, NAND, NOR have been realized in discrete hardware using a single-layer TLG. The functionality can be changed between these operations by reprogramming the resistance of the memristive devices.

Nbconvert Refactor, Jonathan Frederic

Physics

IPython is an interactive Python computing environment. It provides an enhanced interactive Python shell. The IPython Notebook is a browser based interface distributed with IPython. It enables the creation of richly formatted notebooks that contain embedded IPython code. With nbconvert, notebooks can be exported to various formats including, but not limited to, LaTeX, reveal.js, RST, and HTML. This is important for users that want to be able to share their work outside of IPython. This senior project is the addition of a Sphinx LaTeX output format and the refactor of nbconvert.

Intuity Sleeve Redesign, Maxwell Arnold, Brittany Kinkade, Dominic Nicoletti

Mechanical Engineering

No abstract provided.

Exploration Station Kidshake Table, Jeremy Duhe, Philip Hopkins, Matt Ostiguy, Samantha Weiner

Mechanical Engineering

The KIDShake Table is an all mechanical earthquake shake table sponsored by the Exploration Station Children's Museum of Grover Beach. This interactive exhibit has two working mechanisms, a hand crank and pull rope, that provide two axis movement for knocking down block structures. This table was built and designed for a target age of 10 years.

Dedion Axle Senior Project, Nick Schraan, Mark Shushnar, William Swenson, Ramy Tall

Mechanical Engineering

The sponsor, EV Grid Inc. is a company looking to the future with the development of a vehicle to grid infrastructure. The vehicle in development is a Ford E-250 Van which had been converted to electric drive with a front motor, rear drive layout. The sponsor wanted to move the electric motor to the rear and develop an axle to support this change. By eliminating the driveshaft, a more efficient use of battery space could be utilized. The goal of this project is to design and fabricate a prototype deDion rear axle which incorporates a system of drive components that …

Architectural Engineering Earthquake Shake Table, Garrett Gudgel, John Whitmer, Brandan Williams

Mechanical Engineering

The Architectural Engineering Department at California Polytechnic State University, San Luis Obispo, owns and operates a single-axis earthquake shake table that previously was only capable of basic wave motion. After implementing a computer based interface to the existing system, Mechanical Engineering student seniors were able to create control algorithms that can take existing or user created acceleration data from earthquakes as well as any user defined position data to be accurately run on the earthquake shake table.

Adaptive Floor Hockey Device, Chris Gaul, Ricardo Gaytan, Matt Spaulding, Shannon Brant

Mechanical Engineering

Sean is a young boy living with ataxic cerebral palsy. Ataxic cerebral

palsy affects Sean’s balance and coordination, so he uses a walker to

increase his mobility. Sean would like to play Special Olympics Floor

Hockey but his walker prevents him from participating. The goal of this

Senior project was to develop a device to be attached to his previous

walker to allow Sean to play floor hockey in the least restrictive

environment possible. The Adaptive Floor Hockey Device is the product

we designed to satisfy this need.

School Van Access In Nepal, Edgar Corona, Humberto Maldonado, Josh Schiesl

Mechanical Engineering

A need has been identified by a school in Nepal intended for children with Cerebral Palsy, called Sathi Sansar, to develop a more effective solution to loading and unloading students onto the school’s Toyota HiAce van. Currently, a combination of the driver, parents and teachers manually help the students on and off the van. However, this task has proven to be both laborious and time consuming for all parties involved. A solution to this problem needs to be designed and one is currently being developed by a team of engineering students from California Polytechnic State University-San Luis Obispo and Katmandu …

Mercedes-Benz Oil Level Monitor, Emmanuel Camacho, Jonathan Manriquez, James Young

Mechanical Engineering

The purpose of this project is to develop an engine oil level monitoring system that will replace the current dipstick method during vehicle testing for Mercedes-Benz Research and Development North America, Inc. (MBRDNA). Currently, MBRDNA test drivers check the engine oil level twice a day after two eight hour shifts each day. To measure the oil level, the driver parks on a level surface, waits five minutes for the oil to cool, and then manually checks the oil level with the dipstick. The goal of this project is to have a reliable, physical, working prototype that MBRDNA can use for …

Bocce Ball Launcher: An Adaptive Bocce Ball Device, Jake Deschamps, Megan Hughes, Thomas Lynch

Mechanical Engineering

This report details the adaptive bocce launching device created by Team B.A.L.L. and theprocess of designing, building and testing it. The final design was a wirelessly controlled pneumatic catapult capable of propelling a bocce ball such that it would land fifteen feet away and roll the length of the wheelchair accessible bocce courts located at the Colony Park Community Center in Atascadero. A wide variety of users are supported because the system is controlled by a single button which can be actuated by the user’s hand, forearm, head or anything else they are able to move. The catapult allows the …

Beach Wheelchair Project, Rory Aronson, Joshua Marcum, Samuel Coyne, Alex Hayes, Alexa Colburn, Max Hessel, Benedikt Strauss, Marvin Rimmele, Marco Pietsch

Mechanical Engineering

The Beach Wheelchair, Sandcrawler, is a machine intended to help give people with disabilities the full beach experience. The non-profit organization Bridge II Sports sponsored this project, and tasked us with developing the design and fabricating a prototype. This chair has several features including a linkage mechanism that raises and lowers a chair relative to an external frame, hand crank drive with Gates Carbondrive belt and sprockets, buoyant Wheeleez balloon tires, and much more.

Rebounder Fatigue Test Machine, Caroline Reeves, Will Robertson, Ethan Flory

Mechanical Engineering

JumpSport, a company that designs and sells trampolines and trampoline accessories, has sponsored this senior project team to design, build, and test a trampoline fatigue test machine. The machine must simulate a person jumping on the trampoline to test the life of JumpSport’s fitness trampolines and kids’ trampolines. Partway through the design process, the objectives were altered and this senior project team was tasked with merging with another Cal Poly senior project group to create an all-inclusive test machine to accommodate both full-trampoline testing and individual bungee cord testing.

The final design is centered on a slider crank linkage driven …

Low Velocity Impact Tower Feasibility, Setup, And Impact Testing Of Carbon Fiber Reinforced Epoxy Thermoset And Peek Thermoplastic Matrix Composites, Brent Plehn

Materials Engineering

A low velocity impact tower was donated to Cal Poly's Materials Engineering Department along with four fiber reinforced polymer matrix composites. The tower was set up in building 192 in the Mechanical Testing Laboratory. Improvements were made to the tower including adding velocity detection capabilities, making loose hardware inclusive, adding an extra tower arm for better consistency, adding a double jawed clamp for faster testing, and rerouting the tower's compressed air system to improve performance. A standard operating procedure was drafted, tested, and redrafted for impact testing composite panels. The four composite panels consisted of two quasi-isotropic 16 ply AS-1 …

A Design Methodology For Buoyant Prescription Sunglasses, Katherine Burzynski

Materials Engineering

As a means to develop fashionable, buoyant prescription sunglasses, this project focused on identifying a system of lens and frame materials that yield sunglasses that float in water. There was an emphasis on developing a product that could be integrated into the current sunglass market. The term fashionable is used to define a sleek frame style that does not require attaching additional floatation. This methodology relies on the relationships between the strength of the user’s prescription and the volume of the desired sunglass frame style. This relationship was verified through buoyancy testing. This testing included varying the lens material in …

Design And Implementation Of A Micro Force Displacement System, Evan Cate

Materials Engineering

The design and implementation of a micro-force displacement system was completed to test various Micro-Electro-Mechanical Systems (MEMS) devices including silicon diaphragms and cantilevers. The system utilizes a World Precision Instruments Fort 10g force transducer attached to a World Precession Instruments TBM4M amplifier. A Keithley 2400 source meter provided data acquisition of the force component of the system. A micro prober tip was utilized as the testing probe attached to the force transducer with a tip radius of 5um. The displacement of samples was measured using a Newport M433 linear stage driven by a Newport ESP300 motion controller (force readings at …

Application Of Quantum Dots Onto Glass Wafers As A Feasibility Test For The Spectral Down Conversion Of Uv Light For Solar Cells, Anthony Fong

Materials Engineering

Quantum dots have the ability to convert high energy photons into multiple lower energy photons. Down conversion of such high energy photons from sources such as UV light can be beneficial for applications on solar cells which waste much of the energy in the form of thermalization. To test this theory, a solar cell was hooked up to an Amprobe Solar Analyzer and tests were run to compare power output with and without the presence of quantum dots. Additionally, quantum dots were spin coated onto a glass wafer to determine its adhesion ability. Spectrometer readings were taken of the wafer …

Fire Protection Analysis Of The ‘Center For The Arts’ Building', Steven W. Carman

Fire Protection Engineering: Culminating Experience Project Reports

In partial fulfillment of the requirements for the Degree of Masters of Science in Fire Protection Engineering, a prescriptive and performance-based analysis was performed on a building housing the Center for the Arts. The building was constructed in 1947 in California as an automobile dealership and repair shop under the provisions of the then-controlling Uniform Building Code. It subsequently underwent several occupancy changes and has since served as a beauty school, gymnastics center, and currently as a performing and visual arts center. Prescriptive analyses were conducted based primarily upon the provisions of the 2010 California Building and Fire Codes, and …

Life Safety Report Xyz Office Building Denver Colorado, Keith Dix

Fire Protection Engineering: Culminating Experience Project Reports

This report is a Life Safety Analysis of the XYZ building in Colorado. It is a government contract facility and as such prefers that its real name and location not be utilized for this report. The building was assessed prescriptively using the 2009 International Building Code (IBC) and was found to be predominantly compliant with the code and the relevant referenced standards. The building was then assessed using a Performance Based Design in accordance with methodologies found and addressed in common fire protection literature. The Design Criteria chosen to determine tenability for the Required Safe Egress Time (RSET) were Carbon …