Engineering Commons^™

Simulation Of Power Control Of A Wind Turbine Permanent Magnet Synchronous Generator System, Nantao Huang

Master's Theses (2009 -)

This thesis presents a control system for a 2MW direct-drive permanent magnet synchronous generator wind turbine system with the objectives to capture the optimal power from the wind and ensure a maximum efficiency for this system. Moreover, in order to eliminate the electrical speed sensor mounted on the rotor shaft of the PMSG to reduce the system hardware complexity and improve the reliability of the system, a sliding mode observer based PM rotor position and speed sensorless control algorithm is presented here.

The mathematical models for the wind turbine and the permanent magnet synchronous machine are first given in this …

Chemically Sensitive Polymer Coatings For Sh-Surface Acoustic Wave Sensors For The Detection Of Benzene In Water, Robert Lenisa

Master's Theses (2009 -)

Polymer-coated shear horizontal surface acoustic wave (SH-SAW) sensors are investigated for the detection of benzene in aqueous samples. The SH-SAW sensors using three-layer geometry have a single polymer sensing layer which absorbs the analyte and interacts with the surface wave. Several polymers are identified as potential improvements over current sensing films based on glass transition temperature and Hildebrand solubility parameter. The polymers investigated in this work include poly (methyl acrylate) (PMA), poly (butyl acrylate) (PBA), poly (ethylene co-vinyl acetate) (PEVA), bisphenol-A poly (dimethylsiloxane) (BPA PDMS), and bisphenol-A poly (hexamethyltrisiloxane) (BPA HMTS).

The polymers are spin coated on a lithium tantalate …

Investigating The Possible Sources Of Error Using The Method Of Moments To Solve A Dielectric Scattering Problem, Phillip D. Bishop

Master's Theses (2009 -)

In an electromagnetic scattering problem, an incoming electromagnetic wave interacts with an object. The object is typically located in some medium, such as free space. When this electromagnetic wave becomes incident upon the object, the wave scatters. The goal of this work is to analyze the scattered fields for three different incoming wave types: a plane wave, a monopole line source, and a multipole line source. Each source is incident on an infinitely long circular cylinder of lossless dielectric material. Each source has a unique scattering characteristic.

The volume equivalence principle is used to replace the object geometry with mathematically …

An Fmri Study On Supra-Spinal Contributions To Upper And Lower Limb Motor Control, Shancheng Bao

Master's Theses (2009 -)

The differences in the neural mechanisms contributing to upper and lower extremity movement have not been fully elucidated, and this might be a factor that leads to the ineffectiveness of rehabilitation techniques for most stroke survivors. It is unclear whether therapies designed for upper extremities should also be used for the lower extremities, and vice versa. In this study, fMRI was used to examine the supraspinal control of UE and LE movement in both neurologically intact individuals and people with post-stroke hemiparesis. We compared the location, volume, and intensity of brain activity associated with upper and lower extremity pedaling and …

Flame Temperature Imaging Of A Low Nox Burner Via Laser Rayleigh Scattering, Nicholas A. Smith

Master's Theses (2009 -)

Federal and global legislation are requiring increasingly stringent emission regulation on household appliances and in particular water heater burners. Emissions like NOx (NO and NO2) are a growing concern due to their adverse health effects and contribution to tropospheric ozone, acid rain, and smog formation. As NOx is more closely controlled, appliance manufacturers are developing low emission burners for use in water heaters.

Flame temperature is strongly correlated to NOx production. Hence, characterizing flame temperatures in new burners is a key part of improving upon burners used today and the development of future burners. Temperature measurements applied to a new, …

Miniature, High Efficiency Transducers For Use In Ultrasonic Flow Meters, Meghna Saikia

Master's Theses (2009 -)

This thesis is concerned with the development of a new type of miniature, high efficiency transducer for use in ultrasonic flow meters. The proposed transducer consists of a thin plate of a suitable piezoelectric material on which an inter-digital transducer is fabricated for the generation and detection of plate acoustic waves. When immersed in a fluid medium, this device can convert energy from plate acoustic waves (PAWs) into bulk acoustic waves (BAWs) and vice versa. It is shown that this mode coupling principle can be used to realize efficient transducers for use in ultrasonic flow meters. This transducer can be …

Complementarities Of Probabilistic And Evidence Approaches: An Uncertainty Assessment For Selection Of Composite Material, Stella B. Bondi, Resit Unal, Patrick T. Hester, Trina M. Chytka

Engineering Technology Faculty Publications

A complimentary probabilistic and evidence theory approach is utilized to enhance uncertainty assessments in the area of critical safety characteristics for conceptual design. This research provides additional exploration into the failure modes necessary to utilize Fiber Reinforced Polymer (FRP) and various composites to their fullest potential and to minimize uncertainty by comparing probability and evidence theories. This combined approach has been applied to a selection of composite material that could provide uncertainty assessment design for a space transportation system. Uncertainty estimates presented are bounded by belief and plausibility functions. The results may provide additional information to the decision makers in …

Plastic Response Of Dislocation Glide In Solid Helium Under Dc Strain-Rate Loading, Caizhi Zhou, Jungjung Su, Matthias J. Graf, Charles J. Olson Reichhardt, Alexander V. Balatsky, Irene J. Beyerlein

Materials Science and Engineering Faculty Research & Creative Works

We develop a model for the gliding of dislocations and plasticity in solid ⁴He. This model takes into account the Peierls barrier, multiplication and interaction of dislocations, as well as classical thermally and mechanically activated processes leading to dislocation glide. We specifically examine the dc stress-strain curve and how it is affected by temperature, strain rate, and dislocation density. As a function of temperature and shear strain, we observe plastic deformation and discuss how this may be related to the experimental observation of elastic anomalies in solid hcp ⁴He that have been discussed in connection with the possibility …

Fixed Final Time Optimal Adaptive Control Of Linear Discrete-Time Systems In Input-Output Form, Qiming Zhao, Hao Xu, S. Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, the fixed final time adaptive optimal regulation of discrete-time linear systems with unknown system dynamics is addressed. First, by transforming the linear systems into the input/output form, the adaptive optimal control design depends only on the measured outputs and past inputs instead of state measurements. Next, due to the time-varying nature of finite-horizon, a novel online adaptive estimator is proposed by utilizing an online approximator to relax the requirement on the system dynamics. An additional error term corresponding to the terminal constraint is defined and minimized overtime. No policy/value iteration is performed by the novel parameter update …

Improving Affordability: Separating Research From Development And From Design In Complex Programs, Bohdan W. Oppenheim

Systems Engineering Faculty Works

This paper presents arguments for why defense programs creating physical systems should clearly separate three developmental phases from each other: research, development and design. Research is to be performed first by small teams of scientists addressing the "unknown unknowns" and maturing fundamental science from TRL of 1 to about 3. Next, development of physical modules is to be performed by small and highly specialized engineers. Finally, the system-level design should focus on efficient trading off the module locations, sizes and shapes versus system performance, mass, power requirements, etc. The design with all modules mature and available is equivalent to a …

The Effect Of The Probiotic Pediococcus Acidilactici On The Gut Microbiota Ecology Of Rainbow Trout (Oncorhynchus Mykiss Walbaum) Analysed Using Dgge, Alice Anderson

The Plymouth Student Scientist

The microbiota of the gastrointestinal tract heavily influences the health, growth and survival of fish. Probiotics have proved effective in improving fish productivity in aquaculture. Research suggests that probiotics, supplemented in the feed, may elicit these benefits by altering the ecology of the gastrointestinal microbiota. The probiotic Pediococcus acidilactici has been successfully used for terrestrial animals and humans but its use in aquatic organisms has been less researched. In the present study, rainbow trout Oncorhynchus mykiss (Walbaum) were fed a diet that contained Ped. Acidilactici, or a control diet. Analysis of the posterior digesta bacteria, using a non-culture dependant technique, …

Osmotic Regulation Of The Amphipod Gammarus Chevreuxi (Sexton, 1912), Sam Houston

The Plymouth Student Scientist

This study investigated osmotic regulation in the amphipod, Gammarus chevreuxi, and is the first publication of this organism’s osmotic regulatory curves. Unlike most estuarine amphipods studied to date which are hyperosmotic regulators, G. chevreuxi is a hyper-hyposmotic regulator. The hyperosmotic gradient maintained by G. chevreuxi in dilute media is very low (~120mmol.L-1), which has been interpreted as evidence of freshwater ancestry among the Crustacea. Salinity acclimation did not appear to affect heart rate or pleopod beat frequency. The gill cells responsible for ion uptake appeared to be smaller in high salinities or distorted. The apical membrane in concentrated media shows …

Triclosan Enriches For Dehalococcoides-Like Chloroflexi In Anaerobic Soil At Environmentally Relevant Concentrations, Patrick J. Mcnamara, Mark J. Krzmarzick

Civil and Environmental Engineering Faculty Research and Publications

Triclosan is an antimicrobial agent that is discharged to soils with land-applied wastewater biosolids, is persistent under anaerobic conditions, and yet its impact on anaerobic microbial communities in soils is largely unknown. We hypothesized that triclosan enriches for Dehalococcoides-like Chloroflexi because these bacteria respire organochlorides and are likely less sensitive, relative to other bacteria, to the antimicrobial effects of triclosan. Triplicate anaerobic soil microcosms were seeded with agricultural soil, which was not previously exposed to triclosan, and were amended with 1 mg kg⁻¹ of triclosan. Triplicate control microcosms did not receive triclosan, and the experiment was run for …

Resonant Characteristics Of Rectangular Hammerhead Microcantilevers Vibrating Laterally In Viscous Liquid Media, Jinjin Zhang, Fabien Josse, Stephen M. Heinrich, Nicholas J. Nigro, Isabelle Dufour, Oliver Brand

Civil and Environmental Engineering Faculty Research and Publications

The resonant characteristics of laterally vibrating rectangular hammerhead microcantilevers in viscous liquid media are investigated. The rectangular hammerhead microcantilever is modeled as an Euler-Bernoulli beam (stem) and a rigid body (head). A modified semi-analytical expression for the hydrodynamic function in terms of the Reynolds number, Re, and aspect ratio, h/b, is proposed to rapidly evaluate the sensing characteristics. Using this expression, the resonance frequency, quality factor and normalized surface mass sensitivity are investigated as a function of the dimensions of the microcantilever and liquid properties. Guidelines for design of hammerhead microcantilever geometry are proposed to achieve efficient sensing platforms for …

Bs News July/August

Building Services Engineering

No abstract provided.

Continuous Modulations Of Femtosecond Laserinduced Periodic Surface Structures And Scanned Line-Widths On Silicon By Polarization Changes, Weina Han, Lan Jiang, Xiaowei Li, Pengjun Liu, Le Xu, Yongfeng Lu

Department of Electrical and Computer Engineering: Faculty Publications

Large-area, uniform laser-induced periodic surface structures (LIPSS) are of wide potential industry applications. The continuity and processing precision of LIPSS are mainly determined by the scanning intervals of adjacent scanning lines. Therefore, continuous modulations of LIPSS and scanned line-widths within one laser scanning pass are of great significance. This study proposes that by varying the laser (800 nm, 50 fs, 1 kHz) polarization direction, LIPSS and the scanned line-widths on a silicon (111) surface can be continuously modulated with high precision. It shows that the scanned line-width reaches the maximum when the polarization direction is perpendicular to the scanning direction. …

Nanowell-Trapped Charged Ligand-Bearing Nanoparticle Surfaces – A Novel Method Of Enhancing Flow-Resistant Cell Adhesion, Phat L. Tran, Jessica R. Gamboa, Katherine E. Mccracken, Mark R. Riley, Marvin J. Slepian, Jeong-Yeal Yoon

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Assuring cell adhesion to an underlying biomaterial surface is vital in implant device design and tissue engineering, particularly under circumstances where cells are subjected to potential detachment from overriding fl uid fl ow. Cell–substrate adhesion is a highly regulated process involving the interplay of mechanical properties, surface topographic features, electrostatic charge, and biochemical mechanisms. At the nanoscale level, the physical properties of the underlying substrate are of particular importance in cell adhesion. Conventionally, natural, pro-adhesive, and often thrombogenic, protein biomaterials are frequently utilized to facilitate adhesion. In the present study, nanofabrication techniques are utilized to enhance the biological functionality of …

Impact Of Measurement Scale On Infiltration And Phosphorus Leaching In Ozark Floodplains, Derek M. Heeren, Garey A. Fox, Daniel E. Storm, Brian E. Haggard, Chad J. Penn, Todd Halihan

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Increased nutrient loads have resulted in several adverse impacts on surface water quality, including excessive algal growth, fish kills, and drinking water taste and odor issues across the United States and especially in the Ozark ecoregion of northeastern Oklahoma and northwestern Arkansas. The significance of this problem has been highlighted by litigation, with one case even reaching the U.S. Supreme Court (Arkansas et al. v. Oklahoma et al., 503 U.S. 91) which required the upstream state to meet downstream water quality standards. The overarching objective of this line of research was to characterize phosphorus leaching to alluvial aquifers in the …

Finite Element Modeling Of Phosphorus Leaching Through Floodplain Soils Dominated By Preferential Flow Pathways, Ryan P. Freiberger, Derek M. Heeren, Garey A. Fox

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Phosphorus is a critical nutrient in soils, providing both positive and negative effects to different systems. While optimum crop growth requires a range of P above 0.2 mg/L, preventing surface water enrichment generally requires P to be below 0.03 mg/L. Proper application and control of phosphorus is important to increase farming efficiency and to protect freshwater systems from toxic algal growth. While the movement of phosphorus through many soil types has been well-documented, the presence of highly conductive, gravel outcrops and macropores in soil can have a significant, poorly-documented effect on phosphorus movement. In the Ozark ecoregion, for example, the …

Application Of Isothermal Calorimetry To The Study Of Phosphorus Sorption Onto Soils In A Flow-Through System, Chad J. Penn, Derek M. Heeren, Garey A. Fox

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The degree, mechanisms, and kinetics of phosphorus (P) sorption onto soils can have a significant influence on leaching losses of P from soil. The objectives of this study were to measure the impact of retention time (RT) on P sorption in a flow-through system intended to simulate downward movement of a P solution through two different riparian soils, and determine if isothermal titration calorimetry (ITC) can provide useful information reflective of flow-through results. Topsoil from two riparian/alluvial soils was sampled and characterized for P concentrations and parameters related to P sorption. Flow-through P sorption experiments were conducted in order to …

A Morphological Analysis Of A Hybrid Swarm Of Native Ulmus Rubra And Introduced U. Pumila (Ulmaceae) In Southeastern Nebraska, Christian Elowsky, Ingrid E. Jordon-Thaden, Robert B. Kaul

Nebraska Center for Biotechnology: Faculty and Staff Publications

The parental species and hybrid swarm of native Ulmus rubra Muhl. and the introduced, naturalized and weedy U. pumila L. were investigated in a 65-km transect in Lancaster, Saunders, and Butler counties in Nebraska. Thirty-two trees of U. rubra, 32 of U. pumila, and 50 of the hybrid swarm were sampled for leaves and buds and subsampled for flowers and fruits. Leaves were measured for petiole length, blade length, width, primary and secondary teeth per cm, number of secondary teeth per primary tooth, and texture. Buds were scored for color and distribution of trichomes. Flowers were sampled for stamen counts …

Narrow Grass Hedge Effects On Nutrient Transport Following Swine Slurry Application, John E. Gilley, Shannon L. Bartelt-Hunt, Seth J. Lamb, Xu Li, David B. Marx, Daniel D. Snow, David B. Parker, Brian L. Woodbury

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The effectiveness of a narrow grass hedge in reducing runoff nutrient loads following swine slurry application was examined. Slurry was applied to 0.75 m wide by 4.0 m long plots established on an Aksarben silty clay loam soil located in southeast Nebraska. Manure treatments consisted of no manure application and manure application to meet the 1, 2, or 3 year nitrogen (N) requirements for corn. Runoff water quality was measured during three 30 min simulated rainfall events. The grass hedge did not significantly reduce runoff nutrient transport after the swine slurry, which contained relatively small amounts of manure, was applied. …

A Study Of Bicycle Signal Compliance Employing Video Footage, Sam R. Thompson, Kirk Paulsen, Christopher M. Monsere, Miguel A. Figliozzi

Civil and Environmental Engineering Faculty Publications and Presentations

An overview of bicycle signal compliance.

Evaluation Of The Performance Of The Sydney Coordinated Adaptive Traffic System (Scats) On Powell Boulevard In Portland, Or, Miguel A. Figliozzi, Christopher Monsere

Civil and Environmental Engineering Faculty Publications and Presentations

The Sydney Coordinated Adaptive Traffic System (SCATS) is used to mitigate traffic congestion along urban arterial corridors. Although there has been research on SCATS' performance, this report combines three different areas of research about SCATS that are not known to be represented in any research literature. These include: (a) the relationship between SCATS, traffic volumes, and Transit Signal Priority (TSP); (b) between TSP and traffic conditions; and (c) the correlation between signal timing and air quality; in particular, human exposure to the air pollutant PM2.5 at intersections. In addition, this research looked at the key factors affecting transit user exposure …

Developing A Model To Enhance Labor Productivity Using Bridge Construction Benchmark Data, Seonghoon Kim, Yong Bai

Civil and Environmental Engineering Faculty Research and Publications

The Labor Working Status Monitoring (LWSM) Model that incorporates the WRITE and the industry benchmark data was developed through the five steps to enhance labor productivity in bridge construction operations. The first step of the development process was to conduct a literature review, followed by the second step which was to develop the WRITE. During the development, the authors identified the necessary hardware and software for the WRITE and outlined a schematic to show the connection of major hardware components. The third step was to develop the LWSM Model for monitoring the on-site construction labor working status by comparing data …

The Effects Of Angle-Of-Attack Indication On Aircraft Control In The Event Of An Airspeed Indicator Malfunction, Claas Tido Boesser

Doctoral Dissertations and Master's Theses

Analysis of accident data by the Federal Aviation Administration, the National Transportation Safety Board, and other sources show that loss of control is the leading cause of aircraft accidents. Further evaluation of the data indicates that the majority of loss of control accidents are caused by the aircraft stalling. In response to these data, the Federal Aviation Administration and the General Aviation Joint Steering Committee emphasize the importance of stall and angle-of-attack awareness during flight. The high-profile crash of Air France Flight 447, in which pilots failed to recover from a self-induced stall, reinforced concerns over the need for improved …

A Descriptive Analysis Of Public Comments Submitted In Response To Notice Of Proposed Rules On Air Carrier Pilot Qualification, Amy Chaffee Doolittle

Doctoral Dissertations and Master's Theses

In 2009, the crash of Colgan Flight 3407 in Buffalo, NY raised concerns regarding the adequacy of current pilot qualification standards for entering air carrier operations. In response, the U.S. Congress enacted Public Law 111-216, which requires a pilot to hold an Airline Transport Pilot (ATP) certificate in order to be qualified as a flight crewmember under 14 CFR, part 121, and also allows the Federal Aviation Administration (FAA) to modify the requirements to obtain an ATP certificate. In February 2012, the FAA issued a Notice of Proposed Rulemaking (NPRM) outlining these requirements and calling for public comments on the …

Validation Of New Technology Using Legacy Metrics: Examination Of Surf-Ia Alerting For Runway Incursion Incidents, Robert Edward Joslin

Doctoral Dissertations and Master's Theses

New flight deck technology designed to mitigate runway incursions may not be effective in triggering a flight deck alert to avoid high speed surface collisions for runway incursions classified as serious by legacy metrics. This study demonstrated an innovative method of utilizing expert raters and actual high-risk incidents to identify shortcomings of using legacy metrics to measure the effectiveness of new technology designed to mitigate hazardous incidents. Expert raters were used to validate the Enhanced Traffic Situational Awareness on the Airport Surface with Indications and Alerts (SURF-IA) model for providing alerts to pilots to reduce the occurrence of pilot deviation …

The Effects Of Sensor Performance As Modeled By Signal Detection Theory On The Performance Of Reinforcement Learning In A Target Acquisition Task, Nate Quirion

Doctoral Dissertations and Master's Theses

Unmanned Aerial Systems (UASs) today are fulfilling more roles than ever before. There is a general push to have these systems feature more advanced autonomous capabilities in the near future. To achieve autonomous behavior requires some unique approaches to control and decision making. More advanced versions of these approaches are able to adapt their own behavior and examine their past experiences to increase their future mission performance. To achieve adaptive behavior and decision making capabilities this study used Reinforcement Learning algorithms. In this research the effects of sensor performance, as modeled through Signal Detection Theory (SDT), on the ability of …

The Effect Of Microencapsulated Phase-Change Material On The Compressive Strength Of Structural Concrete, Chad Norvell, David J. Sailor, Peter Dusicka

Mechanical and Materials Engineering Faculty Publications and Presentations

Latent heat energy storage through phase-change materials (PCMs) is one possible strategy to control interior temperatures in buildings, improve thermal comfort, and passively reduce building energy use associated with heating and cooling. While PCMs integrated into building structure elements have been studied since the 1970s, challenges of integrating PCMs into building materials while maintaining their heat storage benefits have limited their application in practice. The recent introduction of microencapsulated phase-change materials provides the energy storage capability of PCMs in micron-scale, chemically-inert capsules that can be easily integrated into composite materials such as gypsum wallboard and concrete. The size and physical …