Engineering Commons^™

Development Of Magnetic Fabrics With Tunable Hydrophobicity, Thu Ho

Theses and Dissertations

Polystyrene (PS) fiber mats incorporating iron (Fe) particles were fabricated by electrospinning and the hydrophobicity of the resulting magnetic fabrics was investigated with and without an applied magnetic field. The results show that the hydrophobicity (as measured using water droplet contact angle) increases in the presence of a magnetic field and the hysterisis in the advancing/receding contact angle (a measure of the stickiness of the surface) decreases in the presence of a magnetic field. It is also shown that the contact angle and hysterises increase with decreasing fiber diameter and mat thickness.

A Hybrid Battery Model Capable Of Capturing Dynamic Circuit Characteristics And Nonlinear Capacity Effects, Taesic Kim

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A high-fidelity battery model capable of accurately predicting battery performance is required for proper design and operation of battery-powered systems. However, the existing battery models have at least one of the following drawbacks: 1) requiring intensive computation due to high complexity, 2) not applicable for electrical circuit design and simulation, and 3) not capable of accurately capturing the State of Charge (SOC) and predicting runtime of the battery due to neglecting the nonlinear capacity effects. This thesis proposes a novel hybrid battery model, which takes the advantages of an electrical circuit battery model to accurately predicting the dynamic circuit characteristics …

Flame Synthesis Of Iron Oxide Nanowires For Direct Coal Chemical Looping Combustion, And Tungsten Oxide Nanowires For Enhanced Photoelectrochemical Water Splitting, Pratap Rao

Link Foundation Energy Fellowship Reports

The applications of metal oxide NWs are limited because conventional synthesis methods cannot achieve the scalable, rapid, controllable and economical synthesis of high-quality metal oxide NWs. In the present work, two novel methods for the flame synthesis of metal oxide NWs are developed, and the resulting nanowires tested for two promising, emerging energy conversion technologies: 1) Direct Coal Chemical Looping Combustion, and 2) Photoelectrochemical watersplitting. These synthesis methods are rapid, atmospheric, controllable and scalable, result in highly pure and crystalline materials, and could greatly extend the applicability of metal oxide nanowires to largescale energy conversion and storage problems.

An Investigation Of Medical Device Design And Physical Ergonomics In Healthcare, Adam E. De Laveaga

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

Human factors and process engineering are becoming a prominent area of research and application for industrial engineering principles as healthcare providers seek to improve patient safety, quality the optimization of resources. Human factors engineering and ergonomics play a crucial role in the pursuit of operational excellence and patient safety in healthcare. These disciplines contain the tools required to develop instrumentation, technology and training that can improve the usability of medical technology and the quality of care that patients receive. Designing tasks, tools and processes for optimal human use can enhance performance, reduce errors and improve safety. This thesis encompasses three …

Experimental Investigation Of Hard And Brittle Materials Machining Using Micro Rotary Ultrasonic Machining, Amey V. Patwardhan

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

The demand for miniaturized device and components is rapidly increasing in fields of aerospace, energy, optics, electronics and communication, automation and medical. Rotary Ultrasonic Machining (RUM) is capable of machining hard and brittle materials such as advanced ceramics, glass and silicon used in many industries. Rotary Ultrasonic Machining (RUM) is a hybrid machining process in which material is removed by conventional grinding and ultrasonic machining. Micro RUM is a downscaled version of a macro RUM and is similar to micro Ultrasonic Machining (micro USM), where the vibration takes place in work piece instead of tool.

The goal of this thesis …

A Low-Power Single-Bit Continuous-Time Δς Converter With 92.5 Db Dynamic Range For Biomedical Applications, Sakkarapani Balagopal, Vishal Saxena

Electrical and Computer Engineering Faculty Publications and Presentations

A third-order single-bit CT-ΔΣ modulator for generic biomedical applications is implemented in a 0.15 µm FDSOI CMOS process. The overall power efficiency is attained by employing a single-bit ΔΣ and a subthreshold FDSOI process. The loop-filter coefficients are determined using a systematic design centering approach by accounting for the integrator non-idealities. The single-bit CT-ΔΣ modulator consumes 110 µW power from a 1.5 V power supply when clocked at 6.144 MHz. The simulation results for the modulator exhibit a dynamic range of 94.4 dB and peak SNDR of 92.4 dB for 6 kHz signal bandwidth. The figure of merit (FoM) for …

Dynamics Of Depression Storage During Sprinkler Irrigation And Precipitation Events, Michael B. Mckinney

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Surface depression storage (D_s) is the volume of precipitation excess which is stored by surface microrelief features of soils. The volume of water stored in surface depressions when precipitation rate exceeds infiltration rate reduces the amount of runoff generated. Because Ds is dependent on soil microrelief, land slope, and crop residue, tillage and management practices can have a considerable impact on the magnitude of this value.

When modeling irrigation systems and surface hydrology, depression storage is often treated as a static abstraction, meaning that maximum storage volume must be filled before runoff occurs. However, several researchers have documented …

Solid Oxide Fuel Cells With Both High Voltage And Power Output By Utilizing Beneficial Interfacial Reaction, Chao Su, Zongping Shao, Ye Lin, Yuzhou Wu, Huanting Wang

Faculty Publications

An intriguing cell concept by applying proton-conducting oxide as the ionic conducting phase in the anode and taking advantage of beneficial interfacial reaction between anode and electrolyte is proposed to successfully achieve both high open circuit voltage (OCV) and power output for SOFCs with thin-film samarium doped ceria (SDC) electrolyte at temperatures higher than 600 °C. The fuel cells were fabricated by conventional route without introducing an additional processing step. A very thin and dense interfacial layer (2–3 μm) with compositional gradient was created by in situ reaction between anode and electrolyte although the anode substrate had high surface roughness …

Evaluation Of A Novel Myoelectric Training Device, Ryan Clingman

Theses and Dissertations

While research shows that a patient’s success in using a myoelectric prosthetic arm is dependent on receiving effective training, current methods of training are not designed to effectively hold attention long enough for optimal training. This study focused on evaluating a novel myoelectric training device, consisting of a toy car controlled by EMG signals from the arm. Subjects’ performance with the trainer was evaluated to determine its ability to provide experience with EMG controls. Eight healthy adult subjects were taken through typical initial stages of myoelectric training, then asked to drive the car through a slalom course while the time, …

Energy Efficiency Analysis And Optimization On Mobile Video Wireless Delivery, Jianxin Sun

Department of Computer Electronics and Engineering: Dissertations, Theses, and Student Research

Micro-electronic industry has been boosting the capability of wireless mobile devices on full-scale. However, battery, as the only power source of most mobile devices, is experiencing a relatively slow development. Therefore, how to optimally utilize the limited battery energy on mobile devices under a predefined performance requirement becomes a critical issue. On the other hand, it is still unclear that how the battery capacity consumption is allocated on different working pattern of a specific video codec under various tempo-spatial scales and parameters, which has posed a design challenge on power management on multimedia communication system. Furthermore, an optimization method is …

Introduction Of R-Lcs And Comparative Analysis With Fsc And Mahalanobis-Taguchi Method For Breast Cancer Classification, Benjamin Daniels, Steven M. Corns, Elizabeth A. Cudney

Engineering Management and Systems Engineering Faculty Research & Creative Works

Classification for medical diagnosis is an important problem in the field of pattern recognition. We introduce a new method for classification based on repeated analysis of information tailored to small data sets - the Rote Learning Classifier System. using the Wisconsin Breast Cancer study, this method was compared to three other methods of classification: Mahalanobis-Taguchi Systems, Finite State Classifiers, and Neural Networks. It was found that for the given data set, the Rote Learning Classifier System outperformed the other methods of classification. This new algorithm correctly classified over 92% of the data set. © 2012 IEEE.

Implementing Building Information Modeling In Public Works Projects In Ireland, Barry Mcauley, Alan V. Hore, Roger West

Conference papers

The Irish State in recent years has suffered huge financial losses in the public works sector, which has now pushed the Irish Government to explore new ways of controlling cost. This background lead to the introduction of the Capital Works Management Framework in 2007 which aimed to support the certainty of outcome in terms of cost and quality, as well as improved risk management, through the implementation of fixed price contracts. In order to successfully compete within this framework it is recommended by the authors, that Irish Government moves towards the legal mandating of BIM. This can ensure a greater …

A Master-Slave Soc Structure For Hmm Based Speech Recognition, Hui Geng, Yiyu Shi, Ming Dong, Runsheng Liu

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, we propose a master-slave SoC structure composed of an ARM7-TDMI and a co-processor for Mahala Nobis distance calculation. the SoC was implemented on an Actel ProASIC series M7A3P1000 FPGA. Furthermore, we implement a HMM based speech recognition system based on this SoC. Compared with the conventional ASIC co-processor and slave SoC structure, the new master-slave structure reduces the number of SRAM access and improves the bus efficiency. Experiment results show that with 1.40s Chinese speech feixi and 24MHz clock, the processing time of the M-S SoC system is 1.85s, a 64.12% reduction compared with the software implement …

Efficiency Droop Mitigation And Quantum Efficiency Enhancement For Nitride Light-Emitting Diodes, Xing Li

Theses and Dissertations

In the past decade, GaN-based nitrides have had a considerable impact in solid state lighting and high speed high power devices. InGaN-based LEDs have been widely used for all types of displays in TVs, computers, cell phones, etc. More and more high power LEDs have also been introduced in general lighting market. Once widely used, such LEDs could lead to the decrease of worldwide electrical consumption for lighting by more than 50% and reduce total electricity consumption by > 10%. However, there are still challenges for current state-of-the art InGaN-based LEDs, including ‘efficiency droop’ issues that cause output power quenching at …

Algan/Gan Dual Channel Hfets And Realization Of Gan Devices On Different Substrates, Mo Wu

Theses and Dissertations

GaN-based HFETs demonstrate ubiquitous high power and high frequency performance and attract tremendous research efforts. Even though significant advances have been achieved, there still exist some critical issues needed to be investigated and solved. In particular, high defect densities due to inhomogeneous growth and operation under high power conditions bring many unique problems which are not so critical in the conventional Si and GaAs materials systems. In order to reduce the defect density and heat dissipation of GaN-based HFETs, research work on the realization of GaN-based HFETs on bulk GaN substrate has been carried out and the key problems have …

The Biomechanical Implications Of An Intrinsic Decompressive Pre-Load On A Posterior Dynamic Stabilization System, Jeffrey Ellis Harris

Theses and Dissertations

The purpose of this research was to investigate the influence of applying an intrinsic decompressive pre-load to a particular dynamic stabilization device on the biomechanical response of the lumbar spine. The FlexSPAR, which supports this ability, was used as a test case. A finite element model of a full lumbar spine was developed and validated against experimental data, and tested in the primary modes of spinal motion. The model was used to compare five lumbar spine test cases: healthy, degenerate, implanted with a pre-loaded device, implanted with a device without a pre-load, and implanted with rigid fixators. Results indicated that …

World Energy Balance Outlook And Opec Production Capacity: Implications For Global Oil Security, Ali Mirchi, Saeed Hadian, Kaveh Madani, Omid M. Rouhani, Azadeh M. Rouhani

Michigan Tech Publications, Part 1

The imbalance between energy resource availability, demand, and production capacity, coupled with inherent economic and environmental uncertainties make strategic energy resources planning, management, and decision-making a challenging process. In this paper, a descriptive approach has been taken to synthesize the world’s energy portfolio and the global energy balance outlook in order to provide insights into the role of Organization of Petroleum Exporting Countries (OPEC) in maintaining “stability” and “balance” of the world’s energy market. This synthesis illustrates that in the absence of stringent policies, i.e., if historical trends of the global energy production and consumption hold into the future, it …

Hybrid Spintronics And Straintronics: An Ultra-Low-Energy Computing Paradigm, Kuntal Roy

Theses and Dissertations

The primary obstacle to continued downscaling of charge-based electronic devices in accordance with Moore's law is the excessive energy dissipation that takes place in the device during switching of bits. Unlike charge-based devices, spin-based devices are switched by flipping spins without moving charge in space. Although some energy is still dissipated in flipping spins, it can be considerably less than the energy associated with current flow in charge-based devices. Unfortunately, this advantage will be squandered if the method adopted to switch the spin is so energy-inefficient that the energy dissipated in the switching circuit far exceeds the energy dissipated inside …

Life History Switch Point Plasticy In Response To Pond Drying Alyers Metamorph Allometry And Jumping Performance, Julie Charbonnier

Theses and Dissertations

Animals with complex life cycles can cope with environmental uncertainty by altering life history switch points through developmental plasticity. Pond drying is an important factor which may alter life history switch points in aquatic organisms. Many amphibians can plastically respond to changes in pond drying by emerging earlier, but few studies have examined the post-metamorphic consequences for performance. To investigate the potential carry-over effects of plasticity to pond drying, we studied the túngara frog, Physalaemus pustulosus, a tropical anuran that breeds in highly ephemeral habitats. We conducted a field study with three different water depth treatments in 60 L mesocosms …

Phase-Resolved Characterization Of Conical Turbulent Premixed Flames: An Investigation Of Forced Blowoff Dynamics, Sayan Biswas

Master's Theses

Flame dynamics of a bluff body stabilized turbulent premixed flame as it approaches lean blowoff is of interest for practical applications. It is also important to understand the flame behavior under harmonic flow perturbations as it may occur due to acoustically unstable operation of compact combustors. In this study, a harmonically excited conical flame was studied to determine its behavior under strong burning and near blowoff conditions. Chemiluminescence imaging was employed using a Photron high speed camera to characterize the phase resolved flame characteristics for a range of excitation frequencies from 50 to 400 Hz in confined and unconfined geometries. …

Quantity And Capacity Expansion Decisions For Ethanol In Nebraska And A Medium Sized Plant, Mahsa Khoshnoud

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

Corn-based ethanol is the leader of sustainable sources of energy in the United States due to the abundance of corn and the popularity of ethanol-gasoline mixes. Over the past decade, ethanol production has risen from 1.5 million gallons in 1999 to 13 million gallons in 2011. This increase in production requires expansion of ethanol plants. Since Nebraska is the second highest producer of ethanol, we focus our research on the expansion of ethanol plants in Nebraska.

The aim of this study is to develop an optimization model for capital investments in ethanol in Nebraska and a medium sized ethanol plant …

Linear Precoding For Finite-Alphabet Signaling Over Mimome Wiretap Channels, Yongpeng Wu, Chengshan Xiao, Zhi Ding, Xiqi Gao, Shi Jin

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, we investigate the secrecy rate of finite-alphabet communications over multiple-input-multiple-output-multiple-antenna eavesdropper (MIMOME) channels. Traditional precoding designs based on Gaussian input assumption may lead to substantial secrecy rate loss when the Gaussian input is replaced by practical finite-alphabet input. to address this issue, we investigate linear precoding designs to directly maximize the secrecy rate for MIMOME systems under the constraint of finite-alphabet input. by exploiting the theory of Karush-Kuhn-Tucker (KKT) analysis and matrix calculus, we first present necessary conditions of the optimal precoding design when instantaneous channel-state information (CSI) of the eavesdropper is known at the transmitter. in …

Design, Analysis And Testing Of Haptic Feedback System For Laparoscopic Graspers In In Vivo Surgical Robots, Nikhil Salvi

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Laparo-Endoscopic Single Site (LESS) Robotics Surgery is an advanced technology in the field of Minimally Invasive Surgery (MIS). The LESS surgical robots significantly improve the surgeon’s accuracy, dexterity and visualization, and reduce the invasiveness of surgical procedure results in faster recovery time and improved cosmetic results. In a standard robotic endosurgery, the palpation of tissues is performed by laparoscopic graspers located at the end effectors. The master-slave configuration in robotic surgery leads in remote access to the operation site. Therefore, surgeon’s ability to perceive valuable sensory information is severely diminished. Sensory information such as haptics, which is essential for safe …

Characterization Of Ba1-X-YCaXSrYTio3 Perovskites As Pb-Free Dielectric Materials, Lingling Zhang, Siwei Wang, Xusheng Wang, Kevin Huang

Faculty Publications

Use of lead-containing piezoelectric components in electrical and electronic devices has been banned on the EU market since July 1st, 2006. Development of lead-free high performance piezoelectric materials to meet the strong market demand is therefore imperative. In this paper, we report a systematic study on the structural, dielectric and ferroelectric properties of one class of lead-free piezoelectric materials, Ba_1-x-yCa_xSr_yTiO₃ (x = 0-0.4, and y = 0-0.2) ceramics, using techniques such as XRD, SEM, impedance analyzer, and ferroelectric analyzer. It is found that with increasing Sr concentration in Ba …

Front Burner

Syracuse University Magazine

No abstract provided.

54th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 54th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-endorsed by the Colorado Section of the American Chemical Society and the Society for Applied Spectroscopy. Held in Copper Mountain, Colorado, July 15-19, 2012.

Data Consistency And Conflict Avoidance In A Multi-User Cax Environment, Robert Aaron Moncur

Theses and Dissertations

This research presents a new method to preserve data consistency in a multi-user CAx environment. The new method includes three types of constraints which work by constraining and controlling both features and users across an entire multi-user CAx platform. The first type of constraint includes locking or reserving features to enable only one user at a time to edit a given feature. The second type of constraint, collaborative feature constraints, allows flexible constraining of each individual feature in a model, and the data that defines it. The third type of constraint, collaborative user constraints, allows the constraining of user permissions …

Integrated Analysis Of Hydrothermal Flow Through Pretreatment, Veronique Archambault-Leger, Xiongjun Shao, Lee R. Lynd

Dartmouth Scholarship

Background:

The impact of hydrothermal flowthrough (FT) pretreatment severity on pretreatment and solubilization performance metrics was evaluated for three milled feedstocks (corn stover, bagasse, and poplar) and two conversion systems (simultaneous saccharification and fermentation using yeast and fungal cellulase, and fermentation by Clostridium thermocellum).

Results:

Compared to batch pretreatment, FT pretreatment consistently resulted in higher XMG recovery, higher removal of non-carbohydrate carbon and higher glucan solubilization by simultaneous saccharification and fermentation (SSF). XMG recovery was above 90% for FT pretreatment below 4.1 severity but decreased at higher severities, particularly for bagasse. Removal of non-carbohydrate carbon during FT pretreatment increased …

Efficient Prestressed Concrete–Steel Composite Girder For Medium-Span Bridges, Yaohua Deng

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

In this dissertation, a new Prestressed Concrete-Steel Composite (PCSC) girder system is introduced. The PCSC girder is composed of a lightweight W-shape steel section with shear studs on its top and bottom flanges to achieve composite action with the pretensioned concrete bottom flange and the cast-in-place concrete deck. The PCSC girder is lightweight, economical, durable and easy to fabricate. To prove its feasibility and potential, this study is to investigate design and fabrication issues associated with the PCSC girder. A service design procedure is proposed using Age-adjusted Elasticity Modulus Method (AEMM) to evaluate the time-dependent stresses and strains in the …

Maximizing Transmission Opportunities In Wireless Multihop Networks, Jeong-Yoon Lee, Chansu Yu, Kang G. Shin, Young-Joo Suh

Electrical and Computer Engineering Faculty Publications

Being readily available in most of 802.11 radios, multirate capability appears to be useful as WiFi networks are getting more prevalent and crowded. More specifically, it would be helpful in high-density scenarios because internode distance is short enough to employ high data rates. However, communication at high data rates mandates a large number of hops for a given node pair in a multihop network and thus, can easily be depreciated as per-hop overhead at several layers of network protocol is aggregated over the increased number of hops. This paper presents a novel multihop, multirate adaptation mechanism, called multihop transmission opportunity …