Engineering Commons^™

Enhanced Photorefractivity In A Polymeric Composite Photosensitized With Modified Carbon Nanotubes, Naveen Kumar Lingam

Masters Theses

"This work involves the photosensitization of photorefractive polymeric composites through the inclusion of multiwalled and singlewalled carbon nanotubes grafted to poly(N-vinyl carbazole). The photorefractive nature of the holograms gratings was established using two-beam-coupling, yielding two-beam-coupling gain coefficients approaching 80 cm⁻¹. Degenerate-four-wave-mixing experiments exhibited diffraction efficiencies as high as 60% as well as over-modulation voltages as low as ~ 40 V/µm. These notable figures of merit indicate that the grafting of the various carbon nanotubes to the poly(N-vinyl carbazole) polymer resulted in enhanced photorefractive performance. The mechanism responsible for this enhancement in photorefractive performance is investigated using a variety of experimental …

Methodology And Applications Of Electrostatic Discharge Current Reconstruction By Near-Field Scanning Technique, Wei Huang

Masters Theses

"Electrostatic discharge (ESD) can cause interference in or damage to circuits or systems in many ways e.g., by E- field or H- field coupling or via conduction paths. Although one can roughly estimate the voltage and current at the injection location during an ESD event, the real offending parameter is mostly the ESD current spreading throughout the system. Those currents can be simulated if great simplifications of the system are acceptable. However, even in moderately complex systems, the ability to simulate is limited by a lack of models and computational resources. Independent of the complexity, but obviously not free of …

Automation Of Cad Model Based Assembly Simulations Using Motion Capture, Anup Madhav Vader

Masters Theses

"The manufacturing industry often uses text and video as a supplement for worker training procedures. Unfortunately, text is often difficult to follow and video lends itself to occlusion issues. CAD based animations of assembly operations can overcome these shortcomings while offering greater potential for operations analysis and simulation flexibility. However, creating such CAD based training simulations manually is a time intensive task and many a times fail to reveal the practical assembly issues faced in the real world. Thus, it is highly beneficial to be able to automate these simulations using motion capture from a physical environment. This thesis research …

Development Of Novel Backscatter Communication Systems Using A Multi-Hop Framework And Distributed Beamforming, Vikram Reddy Surendra

Masters Theses

"The goal of this thesis it to develop a wireless networking framework for battery-free devices based on passive, backscatter communication. In contrast to traditional, active communication systems, where the radio signal has to be generated using large amount of energy from batteries, the passive systems reflect the RF signal. The information is encoded by modulating the reflected signal, which consumes significantly less energy than active transmission. The existing passive, backscatter systems have limited communication capabilities. For example, the Radio Frequency Identification (RFID) systems support short-distance, direct communication between active reader and passive tags. The communication range is limited due to …

Design And Critical Performance Evaluation Of Horizontal Axis Hydrokinetic Turbines, Suchi Subhra Mukherji

Masters Theses

"The current work discusses the hydrodynamic performance of horizontal axis hydrokinetic turbines (HAHkT) under different turbine geometries and flow conditions. Hydrokinetic turbines are a class of zero-head hydropower systems which utilize kinetic energy of flowing water to drive a generator. However, such turbines often suffer from low-efficiency. A detailed computational fluid dynamics study was performed using a low-order k-[omega] SST (Shear Stress Transport) turbulence model to examine the effect of each of tip-speed ratio, solidity, angle of attack and number of blades on the performance of small HAHkTs with a power capacity of 10 kW. The numerical models (both two-dimensional …

Neural Mrac Based On Modified State Observer, Yang Yang

Masters Theses

"A new model reference adaptive control design method with guaranteed transient performance using neural networks is proposed in this thesis. With this method, stable tracking of a desired trajectory is realized for nonlinear system with uncertainty, and modified state observer structure is designed to enable desired transient performance with large adaptive gain and at the same time avoid high frequency oscillation. The neural network adaption rule is derived using Lyapunov theory, which guarantees stability of error dynamics and boundedness of neural network weights, and a soft switching sliding mode modification is added in order to adjust tracking error. The proposed …

Slip Ramp Spacing Design For Truck Only Lanes Using Microscopic Simulation, Manoj Vallati

Masters Theses

"This research work proposes recommendations for slip ramp spacing between the TOLs and the general GPLs along Missouri rural interstate highways using a microscopic simulation model, VISSIM. Simulation of peak period rural traffic conditions indicated that heavy vehicle speeds were directly proportional to the lengths of the merge, diverge, and link sections. The proposed design recommendations for slip ramp spacing are based on the results of these section lengths. Design of experiments was carried out using a central composite design. As the slip ramp spacing depended heavily on the lane change behavior of drivers, a sensitivity analysis was performed of …

A Value Model For Product Development Process Using Lean Principles, Salik Yadav

Masters Theses

"This research presents a value quantification model for multi-stage product development Process (PDP) using lean value principles. The PDP stages considered in this research include conceptual development, systems design, detailed design and prototyping stages. The value at any of the PDP stages is formulated as a function of six factors: (a) importance of customer requirements, (b) cost of customer's ownership, (c) parts/service availability, (d) weighted average cost of capital, (e) information evolution, and (f) risk reduction. Factors (a)-(d) are adequately addressed in the literature. This study focuses on information evolution and risk reduction factors. These two factors are defined by …

An Analysis Of The Integration Of Lean And Safety, Pankaj Mahesh Pai

Masters Theses

"The lean philosophy has proven potential to help businesses improve productivity and reduce its losses. Lean can give businesses a cutting edge in this age of global competition. The fundamental principle of lean is to identify wastes in the system and reduce or eliminate them. There is a concern that during lean implementations, the focus on productivity may result in health and safety issues being ignored or worse, changes driven by lean may introduce new hazards. The relationship between lean and safety is not clearly understood. Lean and safety should be compatible. Both strive to improve processes. Both are against …

Strategic Process Integration Of Energy And Environmental Systems In Wastewater Treatment Plants, Bharath Kumar Gangichetty

Masters Theses

"Green environmental practices are increasingly important in combating serious global energy and environmental issues. Most wastewater treatment facilities were built when energy costs were not a concern; however, an increasing demand for energy, changing climatic conditions, and constrained energy supplies have resulted in the need to apply more energy-conscious choices in the maintenance or upgrade of existing wastewater treatment facilities. A detailed analysis of the majority of water and wastewater treatment services shows that most facilities operate far below the efficiency levels needed for effective energy use. Failure to comply with regulated environmental standards is also a problem. Although standards …

A Comparison Of Case-Based Reasoning And Regression Analysis Approaches For Cost Uncertainty Modeling, Karan Banga

Masters Theses

"This thesis presents case-based reasoning approach for estimating the cost and modeling cost uncertainty of a new product in the concept selection stage. Case-based reasoning (CBR) is an approach which uses old cases/experiences to understand and solve new problems. The CBR approach consists of creating a knowledge-base (or database) containing past cases (products), defining a new case (concept), retrieving cases similar to the new case, and adjusting the solution of the retrieved cases to the new case. The first paper compares case-based reasoning, in studying the effects of varying design attribute specifications on cost estimation accuracy and cost distribution reliability. …

Strategic Criteria For Evaluating Inland Freight Hub Locations, Robert Tyler Lipscomb

Masters Theses

"The aim of this thesis is to develop criteria that can be used to evaluate the current capabilities and sustainability of inland freight hubs. A review of the literature highlights the need for a more efficient freight distribution system to combat supply chain deficiencies and the important role that inland freight hubs play in creating this system. Also in the literature is a call for a more comprehensive approach to hub development decisions and the use of multi-criteria decision analysis. The decision to devote resources to logistics developments in a specific region must consider many factors that are both quantitative …

Prediction Of Soft Error Response Of Integrated Circuits To Electrostatic Discharge Injection Via Simulation Field; Package Interaction For Electrostatic Discharge Soft Error Prediction; Full Wave Model For Simulating Noise Ken Electrostatic Discharge Generator, Argha Nandy

Masters Theses

"In the first section, a concept for analyzing soft error response in ICs to ESD via coupling through flex cable structures is presented. Its novelty lies in accounting for the transient electromagnetic fields radiated by the ESD generator that couples to the flex cable PCB thereby causing disturbance on the IC under test. This is accomplished in three stages; first by developing a full wave model of the DUT which includes modeling the PCB and flex cable geometry and validating it in frequency domain with regard to the transfer impedance. This followed by combining the ESD generator with the DUT …

The Effects Of Personal Protective Equipment Level A Suits On Human Task Performance, Yvette L. Simon

Masters Theses

"First response teams dealing with hazardous substances often require the highest level of protection provided by Level A suits. These suits are fully encapsulating, bulky, and heat retentive. The effect of these suits on the wearer's ability to perform various tasks is of interest when it comes to human performance analysis. This research effort examined the effect of the Level A suit on fine motor and gross motor dexterity. Seven members of the National Guard's Civil Support Team (CST) performed a battery of six tasks designed to test these abilities. Tasks comprised the Minnesota Dexterity test and the Mirror Tracer …

Design And Development Of Microwire Feeder For Laser Applications, Amogh J. Shenoy

Masters Theses

"This thesis focuses on the design and development of a microwire feeder for laser applications. The use of wire-feeders in laser welding and electrical discharge machining applications has been prominent which can handle wire of 0.25 mm and it can go up to 10.0 mm in other applications. Development of microwire handling devices is complicated and difficult due to its low buckling strength; the need for high accuracy for its use; and the harsh environment it is exposed to, in laser applications. This paper presents a systematic methodology for the design and development of a high-precision microwire handling device. This …

Incorporating New Technology Into Healthcare: An Analysis Of Performance, Acceptance, And Safety, Anthony Joseph Strawhun

Masters Theses

"Each year, advances in the healthcare industry allows for better patient care and increased ability to save lives. Looking at standardized and common healthcare devices for both inside and outside the hospital environment, this research studied the tradeoffs and human factors that affect operator performance and patient survival. This research studied the impact of human factors and technology in the development and implementation of the automated external defibrillator for out-of-hospital use and the incremental advantages of SMArT infusion pump technology over traditional intravenous infusion pumps for in-hospital care. The study highlights the complex human factors of both products and establishes …

The Mitigation Effects Of A Barrier Wall On Blast Wave Pressures, Nathan Thomas Rouse

Masters Theses

"The study examined the mitigating effects of a blast barrier wall. This area of blast mitigation is of interest due to the many different applications involved in protecting a specific target from an explosive attack. The research follows a 1:50 scale layout using 73 gram, hemisphere-shaped, Composition-4 charges detonated at combinations of three standoff distances from a blast barrier wall set at three different heights. This project used 45 data points for each combination of standoff distance and wall height. This project expanded prior research conducted by the United States Army Corps of Engineers (USACE) by increasing the database of …

Foundry Parameters For Casting High-Aluminum Lightweight Steel In Complex Shapes, Angella Marie Schulte

Masters Theses

"This work investigated the liquid metal treatment and molding practices for Fe- 30wt.%Mn-9wt.%Al-1wt.%Si-0.9wt.%C-0.5wt.%Mo steel. The goal of this research was to determine the process conditions that would produce a tough Fe-Mn-Al-C alloy and the appropriate mold design to produce a defect-free P900 plate.

Notch toughness of age-hardenable Fe-Mn-Al-C alloys decreases as phosphorus increases. Thermodynamic calculations and experimental work show that additions of Ca followed by Ce can be used to mitigate the deleterious effects of phosphorus, and the addition of Ar-stirring can be used to decrease the number of harmful aluminum nitride inclusions. In the solution-treated and aged condition (Brinell …

Data Aggregation In Wireless Sensor Networks, Priya Kasirajan

Masters Theses

"Energy efficiency is an important metric in resource constrained wireless sensor networks (WSN). Multiple approaches such as duty cycling, energy optimal scheduling, energy aware routing and data aggregation can be availed to reduce energy consumption throughout the network. This thesis addresses the data aggregation during routing since the energy expended in transmitting a single data bit is several orders of magnitude higher than it is required for a single 32 bit computation. Therefore, in the first paper, a novel nonlinear adaptive pulse coded modulation-based compression (NADPCMC) scheme is proposed for data aggregation. A rigorous analytical development of the proposed scheme …

The Placement Of Remediation Amendments Into Contaminated Sediments Via Waterjet Technologies, Gavin Hunter Ray Risley

Masters Theses

"The use of amendments to perform in situ remediation of contaminated sediments is a technique that is relatively mature. The need exists to develop a method of amendment delivery that will efficiently place the amendments into the contaminated zone at depth with minimal impacts to the benthic communities and contaminant resuspension. Waterjets have been used for hundreds of years as an excavation, cutting, and cleaning tool, but they can also be used to inject remediation amendments into contaminated sediments if setup properly. In order to test this concept, a waterjet amendment injection system and nozzle have been developed and tested. …

Biodiesel Production Using Supercritical Methanol, Dhaval Nitin Modi

Masters Theses

"The catalyst-free transesterification of oil (triglycerides) in supercritical methanol at a temperature and pressure above 239⁰C and 8.1MPa, respectively, provides a new way of producing biodiesel. High reaction temperature and pressure help to accelerate the transesterification because the supercritical methanol becomes non-polar and has enhanced contact with oil. The supercritical transesterification of soybean oil was carried out in a 170 ml volume high-pressure batch reactor. The pressure within the batch reactor was self-generated from heating the contents since no pumps were used. Transesterification of soybean oil with supercritical methanol readily produced biodiesel. Since the supercritical transesterification is carried out without …

Field Investigation Of Spalling In Bridge Decks With Partial-Depth Precast Concrete Panel Systems Using Non-Destructive Testing, Kandi Rebecca Wieberg

Masters Theses

"This study involved the investigation of the causes of spalling observed in several partial-depth precast prestressed bridge decks in the state of Missouri. Recently it has been observed that several bridges in Missouri with this type of construction have experienced spalling of concrete at the edges of the panels revealing an extreme condition of corrosion in the prestressing tendons, some to the point of rupture. Ground penetrating radar (GPR), which has been shown to be successful in bridge deck evaluation, was used to determine the relative condition of the prestressing tendons as well as the relative condition of the concrete …

Stability Of Streambanks Subjected To Highly Variable Streamflows: The Osage River Downstream Of Bagnell Dam, Kathryn Nicole Heinley

Masters Theses

"Streambank erosion of the Osage River downstream of Bagnell Dam is naturally-occurring; however, it may be significantly worsened due to releases made from the dam to generate hydropower. In this study, six typical outflow release patterns from Bagnell Dam were evaluated to determine their effects, if any, on the stability and the rate and amount of erosion of the banks of the Osage River.

The Bank Stability and Toe Erosion Model (BSTEM), version 5.2, was used to carry out the erosion and stability calculations. The model was validated by using data from another study and comparing the results from BSTEM …

Resistance Switching In Electrodeposited Magnetite Thin Films, Samantha Glen Matthews

Masters Theses

"The resistance switching phenomenon has been extensively studied in metal oxide thin films for its applications in the non-volatile memory industry. The research presented here focuses on magnetite thin films which have been electrodeposited onto gold-sputtered glass substrates via the electrochemical reduction of a Fe(III)-triethanolamine complex in aqueous alkaline solution. Magnetite was chosen for its usefulness in read/write memory applications, its high Curie temperature, its metal-to-insulator (Verwey) transition, and its half-metallic character and attendant spintronic properties. Resistance switching behavior caused by a reversible redox reaction at the anode was observed in the films, demonstrating that electrodeposited films show the same …

Evaluation Of Liquefaction-Induced Lateral Spreading In The Midwest, Kermit Nathanial Applegate

Masters Theses

"The Central United States is home to several seismically active regions: the Wabash Valley Seismic Zone, the South Central Illinois Seismic Zone, and the New Madrid Seismic Zone. All three of these regions are capable of inducing large ground motion throughout the Mississippi Valley and along the eastern border of Missouri. This has been supported by many paleoseismic studies conducted throughout the region, which have identified numerous instances of liquefaction phenomena. The fluvial deposition process associated with the Mississippi river valley makes it a prime location for possible liquefaction and lateral spreading effects. However, there are few studies pertaining to …

Emi Suppression Of Dc-Dc Synchronous Buck Converters By Layout Optimizations And Emi Prediction Using Non-Linear And Spice Circuit Co-Simulation, Ankit Bhargava

Masters Theses

"The oscillation on the phase voltage is due to the resonant structure formed by a parasitic loop (consisting of two FETs and the input decoupling capacitors) inductance and the output capacitance of the low side FET. Therefore, it is important to minimize this parasitic loop inductance. A simulation guideline is developed on full-wave modeling and simulation of buck converter layouts to estimate the parasitic loop inductances. Furthermore, this method is taken one step further to estimate the far-field radiation from the loop. These simulations were verified on six PCB variants of the buck converter and were compared with measurements in …

Strength Evaluation And Transportation Behavior Of Preformed Particle Gel Using Screens And Tubes, Rajesh Sarma Challa

Masters Theses

"This research included a series of experiments, using screen models to evaluate the strength of swollen gel particles. It also includes the study of PPG propagation and extrusion behavior through tubes of various internal diameters. The effect of the particle gel swelling ratio (depending on brine concentration), flow rate; and mesh size on the gel injection pressure and injectivity were studied. The results show that gel injection pressure depends primarily on the swelling ratio and the mesh size. However, the injection pressure does not increase significantly with injection rates, behavior consistent with the real-time injection pressure and injection rate change …

Excitation Of Whispering Gallery Modes In Glass Microspheres Using Optical Fiber Couplers, Sudha Sneha Devarakonda

Masters Theses

"This research is a study conducted on the excitation of whispering gallery modes (WGM) in small micron-scale glass spheres. Optical WGM may be represented by a light wave that propagates along the surface of the sphere and reaches back itself in phase at specific wavelengths. Due to this, very high intensities of light with narrow line widths circulate in the microspheres contributing to high Q factor. The evanescent field of an optical waveguide is used to resonantly stimulate the WGM.

The WGM excitation in fused silica spheres was demonstrated in the laboratory with 60% coupling efficiency. Tapered optical fibers were …

Mechanical Properties And Microstructure Study For Direct Metal Deposition Of 316l Stainless Steel, Tian Fu

Masters Theses

"Direct metal deposition or laser cladding is a process capable of producing fully dense and net shape metal products and this process could be used on coating metal components in various engineering applications. This process has fast heating and cooling rates which can improve the surface hardness and provide excellent adhesion through metallurgical bond between coating material and substrate. This paper evaluated the laser deposited 316L stainless steel coating on 4340 steel, which is widely used for aircraft landing gear applications. The microstructure, micro-hardness and quantitative EDS were explored to verify the coating properties. The desired homogeneous microstructure and high …

The Marketing Value Of Graduate Certificate Programs In Higher Education: A Strategic Assessment, Susmitha Akula

Masters Theses

"The last five years have seen a significant increase in the popularity of non degree graduate certificates. This increase has raised questions about the value of graduate certificate programs from the perspective of students, alumni and industry employers. Do certificate programs provide real world skills and knowledge valuable to industry? Do they serve as effective recruiting tools for the university? Do they provide opportunities for students to meet their professional goals in terms of salary increase, promotions, and the like? The present research is specifically aimed at answering these questions. Surveys that assess perceptions of value of graduate certificates to …