Engineering Commons^™

Calibration Of Resistance Factors For Axial Capacity Of Driven Pile Into Missouri Soil, Mulugeta Abay Kebede

Masters Theses

"Over the past two decades the load resistance factor design (LRFD) has been accepted by the American Association for Transportation and Highway Officials (AASHTO) for the design of bridges. This approach is now gaining widespread popularity in the United States for substructure bridge design, including the design of driven pile foundations, as the states calibrate the geotechnical resistance factors for local geological conditions and practices. This study presents the geotechnical resistance factors calibrated for axially driven pile using the first-order reliability method (FORM) for the target reliability index of 2.33 and 3.0 based on 64 end-of-drives (EOD) and 22 beginning-of …

Establishing Workload Limitations For Application In Human Systems Integration, Muhammet Servet Gulum

Masters Theses

"As the amount of technology involved in the typical workplace increases and standard operational procedures become increasingly sophisticated the danger of overloading an operator's mental resources is increasing. As much as these technological developments help operators with daily tasks, for example by providing information via monitors and wireless headsets; it also increased the mental workload due to the bombardment of information. Mental workload is commonly associated with information processing tasks, limits. With all the extra information inputs it is difficult to set limits where excessive information becomes dangerous. The workload optimization is critical as it directly affects system performance and …

Evaluation Of Alternative Methods For Surface Preparation And Deposition Of Cerium-Based Conversion Coatings On Aluminum Alloys, William J. Gammill

Masters Theses

"This thesis investigates alternative surface preparation and deposition methods for cerium-based conversion coatings (CeCC) on high strength aluminum alloys. Cerium-based conversion coatings are being investigated as a more environmentally friendly replacement for chromium-based conversion coatings. Currently, the alloys are immersed in strong alkaline and acidic solutions to prepare the aluminum surfaces for conversion coating, in which immersion may not be suitable for all situations. Alternatives to this method were investigated, including wipe application of solution, ultrasonic processing in deionized water, and abrasive blasting with alumina. AI 7075-T6 test panels were prepared using each of these methods and compared to a …

Thrust Measurement Of Dielectric Barrier Discharge Plasma Actuators And Power Requirements For Aerodynamic Control, Joseph William Ferry

Masters Theses

"Plasma-based aerodynamic actuators are of interest to researchers because they do not require moving control surfaces or a source of pressurized air to modify a flow field. Dielectric barrier discharge (DBD) plasma actuators have the added advantages of simple installation and low power consumption.

DBD plasma actuators are AC devices. This work measured actuator power consumption and thrust production for driving frequencies between 1 and 18 kHz, and for driving voltages of 6 and 9 kV peak to peak. The actuator consumed between 3 and 22 W of power and produced thrust levels between 0.05 and 0.2 mN per meter …

Experimental And Modeling Comparison Of Modular Photovoltaic-Thermal Solar Panels, Nicole C. Annis

Masters Theses

"Three different prototype photovoltaic-thermal panels using water as the cooling fluid were tested simultaneously. The first two panels (Panel A and B) consisted of a highly conductive thermal sheeting and different sized copper tubing. The third panel (Panel C) consisted of copper tubing with an aluminum fin. Thermal images were used to verify the heat transfer across the panels and compare the amount of heat radiating off the back of the photovoltaic-thermal panels versus the standard photovoltaic paneleaf Three A type panels were thermally connected in series. Three photovoltaic panels were also tested for an electrical comparison. The purpose of …

Sintering And Microstructural Effects On Mechanical Properties Of Zirconium Carbide-Tungsten Cermets, Melissa M. Giles Craft

Masters Theses

"Zirconium carbide-tungsten cermets were prepared by in situ reaction sintering a mixture of zirconia and tungsten carbide. Tungsten is a refractory metal with a melting point of 3422⁰C; however, its mechanical strength decreases significantly with increasing temperature. One approach to improve the elevated temperature strength is to add ceramic particulates to the matrix. Zirconia and tungsten carbide were compacted and then reacted and sintered in a single step by heating to 2050⁰C. The resulting stoichiometric zirconium carbide-tungsten cermet had a relative density greater than 96%. Cermets with two different grain sizes were produced by altering the final sintering temperature. Sintering …

"In Situ" Printed Circuit Board Material Extraction Procedure With Conductor Surface Roughness Study, Amendra Koul

Masters Theses

"Analysis of printed circuit board (PCB) behavior in a wide frequency range from tens MHz to at least 40 GHz is very important for modern high-speed digital design and assuring for signal integrity (SI). this analysis includes preliminary evaluation of per-unit-length parameters of the PCB transmission line and transmission line characteristics, such as propagation and attenuation constants, and also extraction of these parameters from measurements on real test vehicles. This thesis describes an impedance calculator tool, which can substantially speed up PCB design, and the second topic considered in this work is characterization of dielectric parameters of substrates of printed …

Influence Of Flow Baffles On Mixing Of Two Air Streams Flowing In A Mixing Chamber With Dissimilar Temperatures: A Computational Study, Abdulmunam Salem Shaban

Masters Theses

"One of the most important components of heating, ventilation, and air conditioning (HVAC) is an air handling unit (AHU) which is used to condition and mix air that arrives from outside the building (OA) and return air (RA) that exits from the indoor space. Poor mixing between the warm return air and the cold outside air often leads to air stratification in AHU, which results in various problems, such as, nuisance trips of low temperature safety thermostats, freezing of chilled or hot water coils in a stratified subfreezing air stream and loss of control when sensors cannot read the true …

Performance Evaluation Of Energy Efficient Lighting Associated With Renewable Energy Applications, Allison Nicole Sperber

Masters Theses

"The present study demonstrated lighting loads as an energy end use associated with renewable energy system applications. Incorporating an energy efficient end use within a renewable energy system can be especially beneficial regarding size and portability. Light-emitting diodes (LEDs) are an energy efficient alternative to traditional outdoor lighting, which is currently dominated by high intensity discharge source lamps. LEDs provide the ability to mitigate the negative impacts of diesel consumption when a diesel generator is used independently or as a backup for renewable energy applications in remote localities. In-field data was collected of traditional metal halide lamps and two comparable …

Embedded Optimal Control Of Mobile Robot Formations Using Neural Networks, Bryan M. Brenner

Masters Theses

"This work first presents the development of a nearly-optimal control scheme and then evaluates the effectiveness of this nearly-optimal control scheme by comparing it to a non optimal controller in Paper I. It is shown that the proposed nearly-optimal scheme is a significant improvement over the non optimal one in both simulation and hardware tests. The test was carried out on a differentially driven robotic vehicle in both obstacle free and obstacle ridden environments. On the other hand, the controller introduced for the obstacle avoidance in Paper II will also function in the absence of obstacles so that no switching …

Automatic Detection Of Malignant Melanoma Using Boundary Gradient Information In Dermoscopy Images, Yogesh Ajit Dandekar

Masters Theses

"This thesis demonstrates an algorithm which uses local border features, primarily derived from the border gradient, to help determine whether the lesion is a malignant melanoma or a benign lesion. Although this algorithm uses manually-marked lesion borders, it could be included in a fully automatic routine. A Prewitt algorithm with a window size proportional to the area of the lesion is used to calculate the gradient over the entire lesion boundary. This gradient value is used to calculate various boundary features, such as mean, standard deviation, and direction of maximum gradient. The dark and white areas inside the lesion combined …

Symbol Synchronization And Dynamic Channel Estimation In Multiple Input Multiple Output Systems Using Statistical Analysis Of Eye Diagrams, Abhishek Gupte

Masters Theses

"The research work presented in this document is the continuation of the project to develop a Multiple Input Multiple Output (MIMO) system using band-limited signals in strong multipath environments. The modulation format used is Gaussian Frequency Shift Keying (GFSK). Band-limiting introduces controlled Inter-Symbol Interference (ISI), which along with a multipath environment degrades the features of the received signal waveform that are vital to the performance of standard symbol synchronization techniques. A low complexity algorithm was deemed necessary to counter this problem so that the benefits of conserving bandwidth would not be obviated by an expensive and elaborate receiver architecture.

Such …

Performance Evaluation Of A Novel Diesel Fuel Air Separation And Filtration System For An Indirect Injection Diesel Engine, Michael Ray Hess

Masters Theses

"The objective of this research was to evaluate an air/fuel separation system known as a Fuel Preporator. The device's efficacy was determined by studying the effect of air entrainment on engine performance and fuel consumption of a General Motors 6.5 L naturally aspirated indirect injection (IDI) diesel engine. A test bed was developed to accommodate the test engine and test methods were adapted from federal regulations for steady-state engine testing (40 CFR 89 Subpart E). Cases of 0%, 5%, 10%, and 20% volumetric air entrainment were investigated for engine operation with and without the Fuel Preporator. Key measured engine performance …

Freeze Extrusion Fabrication Of 13-93 Bioactive Glass Scaffolds For Bone Repair, Nikhil D. Doiphode

Masters Theses

"We have investigated Freeze Extrusion Fabrication (FEF) of 13-93 bioactive glass to fabricate three dimensional scaffolds for bone tissue engineering. Bioactive glass paste was prepared for consistent extrusion through micro-nozzle and controlled porosity scaffolds were fabricated using additive manufacturing FEF. CAD models were prepared for different scaffold designs and computer controlled layer-by-layer deposition of pseudoplastic paste was carried out to in accordance. Liquid nitrogen assisted freezing of pastes was used for the consolidation of deposited layers. Post processing binder burnout and sintering schedules were designed for evaporation of organic binder and densification of glass. Sintering shrinkage was measured, and X-ray …

Implementation Of Integrated Function Structure And Object-Oriented Design Framework, Qiong Gao

Masters Theses

"The function structure method is commonly used in mechanical product design. Although a function structure allows defining all the functions of the components of a product and their interactions, it does not have an effective architecture for the software design of a mechatronic product. An integrated function structure and object-oriented design framework was recently developed to overcome this disadvantage. In this thesis, the implementation of this framework to design several products in different categories, including an inkjet printer, and electric screwdriver and a vacuum cleaner, is discussed. The design results obtained using the new framework are compared to the design …

Field Analysis Of Photovoltaic Ultracapacitor Energy Storage System, Jenna Vujic

Masters Theses

"In the field of innovative power sources, photovoltaics are playing an important role as a clean energy source. Because performance is dependent on instantaneous weather conditions, all stand-alone photovoltaic (PV) systems require an energy storage device. Batteries are not suitable for PV source applications due to depth of discharge restrictions, maintenance requirements and minimal power density availability. However, ultracapacitors (UCAPs) have a high power density, require little maintenance, and can be used in sequence with a dc-dc converter to maintain power output at an increased depth of discharge. This paper describes a PV-UCAP power system used to collect and compare …

Innovative Concrete Bridging Systems For Pedestrian Bridges: Implementation And Monitoring, Kurt Edward Bloch

Masters Theses

"Two precast, prestressed pedestrian bridges were designed for rapid construction in Rolla, MO, utilizing high-strength concrete (HSC) and high-strength self-consolidating concrete (HS-SCC) with a target 28 day compressive strength of 68.9 MPa (10,000 psi) and release compressive strength of 24.1 MPa (3,500 psi). In addition, a glass fiber reinforced polymer (GFRP) bar reinforced deck panel system was utilized in one of the two deck panels on each bridge.

Material properties were tested for compression, elastic modulus, modulus of rupture, splitting tensile strength, creep, and shrinkage following ASTM standards. Instrumentation systems within the spandrel beams and precast deck panels were implemented …

Distributed Spatiotemporal Detection For Chemical And Biological Threats Using Human Immune Mechanisms, Yatin Bodas

Masters Theses

"Ubiquitous detection of chemical and biological (CB) threats in an urban environment using widely distributed, low-cost, broad-spectrum sensors carried by public or on vehicles is extremely desirable and pertinent for homeland security. These distributed sensors should interoperate autonomously and adaptively to meet stringent operational and detection performance requirements. This research explores the use of scalable detection methodology, inspired by the human immune mechanisms to meet these challenges. An adaptive spatiotemporal control mechanism is proposed to organize the detection behavior of spatially dispersed sensors using peer-to-peer communication so that a shorter response time, higher probability of detection and lower false alarm …

Characterization Of Geotechnical Variability Based Upon Sampling Frequency Using Monte Carlo Simulation: A Study Of The Kcicon Project, Kerry Allen Magner

Masters Theses

"The geotechnical variability of individual homogeneous isotropic soil units is of interest during the process of determination of adequate geotechnical design parameters for almost all construction projects. In this study, an attempt is made to quantify the effects of sampling frequency (sample size) on the mean, variance, and coefficient of variation of individual geomechanical parameters within a distinct soil type.

In-situ geotechnical sampling data and laboratory testing data from the kcICON project was provided by Terracon Consultants, Inc. (Terracon) of Lenexa, Kansas for analysis within this research project. This soil sampling and laboratory testing was performed by Terracon as part …

Adaptive User Interface For Vehicle Swarm Control, Paul Robinette

Masters Theses

"An algorithm to automatically generate behaviors for robotic vehicles has been created and tested in a laboratory setting. This system is designed to be applied in situations where a large number of robotic vehicles must be controlled by a single operator. The system learns what behaviors the operator typically issues and offers these behaviors to the operator in future missions. This algorithm uses the symbolic clustering method Gram-ART to generate these behaviors. Gram-ART has been shown to be successful at clustering such standard symbolic problems as the mushroom dataset and the Unix commands dataset. The algorithm was tested by having …

Analysis Of Nationwide Intercity Travel Demand On The Us Transportation Network, Tao Li

Masters Theses

"In this thesis, three issues about the intercity travel demand on the US transportation network are addressed. The final one is the estimation of the domestic passengers' delay cost. A scheme is designed by assuming that costs incurred by flight delays relative to the original flight schedules are imposed at passengers' final destination airports. It is applied to estimate the total domestic delay cost of year 2007 and reasonable results arc obtained. The second one is the air travel demand estimation. Two route-based optimization models are proposed to estimate the travel demand based on available data. It is shown that …

Glass Fiber-Reinforced Polyurea Strengthening Of Reinforced Concrete, Courtney Elizabeth Greene

Masters Theses

"Wide varieties of concrete repair-retrofit and strengthening methods have been developed and are being widely implemented. In recent years, the need for such strengthening systems has become apparent with increasing demands on aging infrastructure. These strengthening systems need to be increasingly more adaptable, providing ease of construction as well as withstanding a variety of loading conditions and hazards. Exterior-applied fiber-reinforced polymer systems are increasingly being used to meet these demands. The research contained herein investigates the strengthening benefits and characteristics from a specific glass fiber-reinforced polyurea coating system applied externally to structures by means of spraying. This coating would allow …

Finite Element Modeling Of Bird Strikes And Parametric Evaluation Using Design Of Experiments (Doe), Venkata Varaha Raja Naga Prathyush Bheem Reddy

Masters Theses

"One of the major threats to Aviation industry is the in-flight impact of birds. Aircraft windshields are intensively vulnerable to damage and hence need a certification requirement for a proven level of impact resistance. Bird strike experiments are very expensive and henceforth explicit numerical modeling techniques have grown importance. This compilation mainly relies on the theory of hydrodynamic impact and addresses basic shockwave equations. A smooth particle hydrodynamics based approach is chosen and the numerical simulation is carried out using contact-impact coupling algorithm. The simulation is run using the nonlinear explicit finite element code LSDYNA ver.971, developed by Lawrence Livermore …

Gpu Based Processing For Airborne Detection, Dheeraj Singiresu

Masters Theses

"Onboard real-time processing is highly desirable in airborne detection applications. As the data processing involved here is computationally expensive, typically high power multi-rack system is required to achieve real-time detection. Use of such hardware is often not feasible in an airborne application due to space, power and weight constraints. In this thesis, different computing architectures suitable for real-time onboard processing are compared in terms of computation speed, watts/GFLOPS, and weight/GFLOPS. A brief description of the modem GPU architecture and the current GPGPU technology is provided. GPU implementations of some computationally expensive image processing applications such as band-to-band registration for Multi …

Using Value Stream Mapping For Cost Modeling, Emily Marie Tucker

Masters Theses

"This thesis presents an effective cost model for the Selective Laser Sintering (SLS) process used in additive manufacturing practices. The various factors that influence the total cost of a build on both small and large frame machines are discussed. These attributes, which include labor and overhead rates, material costs, and process times, combine to generate the driving force behind a manufacturer's decision to use the small or large SLS machine for mass production. By developing and evaluating a current state value stream map for the small SLS machine, a financial analysis of the SLS process can be performed. By assigning …

Bayesian Approaches On Observational Before-After Highway Safety Analysis, Daxiao Liu

Masters Theses

"Observational before-after evaluation of roadway safety treatments effect is a necessary and challenging study area for traffic safety engineers. In decades, empirical Bayesian approach has been widely adopted among researchers in this area. In this approach, the researcher combined before period observation data with a safety performance function estimated from similar groups to estimate the expected number of crashes that would have occurred in the after period without the treatment. Comparing this estimate with the number of crashes observed in the after period, the researcher evaluated the effectiveness of the treatment. This approach accounts for well-known regression-to-the-mean effects. However, as …

Evaluation Of Variable Speed Limits Using A Genetic Algorithm Approach To Calibrate A Vissim Model, Brian Joseph Schaefer

Masters Theses

"The variable speed limit (VSL) system has been adopted on more and more roadways across the globe as an engineering tool for controlling traffic flow, particularly during congestion situations. An important and fundamental question raised among traffic engineers is: Are the costs of installing and operating variable speed limits really justified? In order to answer this question, this thesis measures the effectiveness of the VSL system applying the VISSIM microscopic simulation model to a non-recurrent congestion situation. For the analysis, a section of interstate was modeled in VISSIM and calibrated so that the simulated results closely reproduce the observed data …

Target Detection And Feature Evaluation Of Airborne Mine Target Images, Deepika Kamakshi Timmavajjula

Masters Theses

"Target segmentation and detection problem is one of the preliminary approaches in analyzing an image. Many edge, region and texture based techniques have been proposed in literature. These techniques often have limitations based on types of image data, kind of segmentation of interest and the problem domain. Mine detection problem dealt with for this thesis has mine target images which have a center target consisting of false alarm or mine patch which has to be detected and features evaluated to evaluate various parameter performances. Thus, segmenting the mine patch becomes the first step of analyzing these images. This thesis is …

Synthesis And Characterization Of Limpo[4] (M=Mn, Ni And Fe) Olivine Materials., Azlin Sanusi

Student Works (2010-2019)

Lithium transition metal phosphate, LiMPO4 compounds with olivine structure namely LiMnPO4, LiNiPO4 and LiFePO4 were successfully synthesized in the present work. LiMnPO4 and LiNiPO4 were synthesized by the sol-gel method with tartaric acid as the chelating agent. LiFePO4 was synthesized via the chemical precipitation and low temperature sterilizer heating method. TGA was carried out on LiMnPO4 and LiNiPO4 samples to determine the firing temperature of the gel precursor and the thermal stability of the prepared samples. LiMnPO4 was heated for 15 hours at various temperatures and LiNiPO4 was formed at 1000 oC with firing time of 24 hours. Firing of …

Inductively Coupled Plasma Dry Etching Process On Planar Lightwave Circuit Fabrication., Chuah Khoon Seah

Student Works (2010-2019)

The main objective of this project is to master state-of-the-art techniques and knowledge in silica etching in order to achieve high quality waveguide circuit on Planar Lightwave Circuit devices. Another objective is to optimize the clean room research strength, surface characterization, microscopy techniques and similar semiconductor manufacturing processes.Initially, these processes were conducted with wet etching method that utilized diluted hydrofluoric acid (HF) and buffered oxide etch (BOE). Several problems arising such as mask peel-off, poor sidewall profile and defect waveguide channel during the pattern transfer process due to its’ isotropic nature. Alternatively, dry etching method was conducted via Inductively Coupled …