Engineering Commons^™

The Thermoluminescence Properties Of Manganese Doped Zns Nanophosphor., Khalid Humaid Zahir Al-Hinai

Student Works (2010-2019)

The thermoluminescence (TL) properties of Manganese (Mn) doped ZnS nanophosphors were investigated after gamma irradiation at room temperature. The ZnS:Mn nanophosphors were prepared by chemical precipitation method by using Zinc sulfate, Sodium sulfide and Manganese sulfate. 1 mole, 2 moles and 3 moles of Manganese sulfate were used to have different concentrations of Mn in doped ZnS. The formation of the nanophosphors was characterized by high resolution scanning electron microscopy FESEM, XRD and EDX. The obtained products consist of particles with the dimension about 85–150nm. Comparison between ZnS nanophosphors and commercial ZnS powder glow curves was studied. It was observed …

Synthesis Of Chromium-Based Ziegler-Natta Catalysts And Thier Application In Ethylene Polymerization And Copolymerization., Wong Jun Xuan

Student Works (2010-2019)

Four chromium-based oxo-trinuclear carboxylate complexes were prepared by reacting Cr(NO3).9H2O with acetic acid and substituted carboxylic acids to produce [Cr3O(CH3COO)6.3H2O]NO3.7H2O,[Cr3O(ClCH2COO)6.3H2O]NO3.3H2O, [Cr3O(Cl2CHCOO)6.3H2O]NO3.H2O and [Cr3O(Cl3CCOO)6.3H2O]NO3.2H2O, which alysis (TGA).Chromium content in each complex was determined by titrimetry method and the result was in good agreement with that from TGA. Chromium(III)monochloroacetate complex[Cr3O(ClCH2COO)6.3H2O]NO3.3H2O in combination with diethylaluminium chloride formed heterogeneous catalyst system for ethylene polymerization and ethylene-propylene copolymerization. Both Al/Cr ratio and temperature influenced the catalytic activity. The maximum activity of ethylene polymerization was 1768 gPE/gCr/hr/atm, achieved by polymerizing ethylene at 29°C with Al/Cr ratio 30.8. Effect of chloro-substituent groups on carboxylic ligand was studied …

Inversion Of 2d And 3d Dc Resistivity Imaging Data Forhigh Contrast Geophysical Regions Using Artificial Neuralnetworks., Ahmad Neyamadpour

Student Works (2010-2019)

In electrical resistivity imaging surveys, the field data along a profile are normally acquired as a subsurface distribution of apparent resistivity. One common method to obtain the true resistivity distribution is by inverting the apparent resistivity values. However, the inversion of DC resistivity imaging data is complex due to its non-linearity. This is especially true for regions with high resistivity contrast. For the complicated subsurface structure, especially when regions of high resistivity contrast exist, a conventional inversion technique based on least squares methods may not be able to invert the DC resistivity data with adequate accuracy. Therefore, in this study, …

Reflective And Beam-Through Types Of Fiber Optic Sensor For Displacement Measurement., Walaa Fawzi Al–Masri

Student Works (2010-2019)

This dissertation proposes and demonstrates fiber-optic displacement sensor (FODS) theoretically and experimentally using the intensity modulation technique to measure a displacement from a probe and target. The sensor uses a multimode plastic bundled fiber as a probe and He-Ne laser as a source. The performance of the sensor is compared for different type of probe and target. For a pair type bundled fiber, both the experimental and theoretical results exhibit the same type of characteristic features. The front slope sensitivities are obtained at 1.71 and 1.0 mW/μm for the theoretical and experimental approaches respectively, while the back slope sensitivities are …

Band Structure Of Fe Based Superconductors., Teh Yee Lin

Student Works (2010-2019)

Several iron containing superconductors are discovered in 2008. The discovery introduced a new class of high-temperature superconductors, which are iron-based. The iron-based superconductors do not resemble conventional superconductors and have properties on their own which differ from the cuprates. We have studied the iron selenium, FeSe compound by removing some Se atoms from the lattice forming Fe:Se = 2:1 and 8:6 and also by replacing the Se vacancy with tellurium, samarium and oxygen atoms forming Fe:Se:Te = 2:1:1 and 8:6:2, Fe:Se:O = 8:6:2 and 8:4:2, FeSeSmO, FeSeTeO, Fe2SeSm2O2, FeSeTeSmO and FeTeSmO. The band structures for each lattice are calculated by …

Synthesis And Characterization Of Silicon Oxide And Silicon Carbide Nanostructures., Majid Salim Mohammed Al-Ruqieshi

Student Works (2010-2019)

Silicon oxide nanostructures have attracted extensive interests in recent years due to their physical and optical properties. SiOx nanostructures are synthesized by catalytic and non-catalytic approaches. With catalytic approach, long and uniform amorphous silicon oxide nanowires, nanofibers (comet and tree like), nanocakes and nanocages were synthesized on Si substrate by carbothermal evaporation reactions of TiO2 at high temperature. The SiOx nanowires were about 13 nm to 243 nm in diameters and 194 nm to several microns in length and the nanofibres with diameter between 8 nm to 30 nm and around 50 nm to 2.5μm in length. The diameter and …

Production Of Multiwall Carbon Nanotube For Alcohol Sensor Application., Ebtehal Saleh Alshaqaq

Student Works (2010-2019)

Multiwall carbon nanotube/polyethylene oxide (PEO), multiwall carbon nanoube/polyvinyl alcohol(PVA) and multiwall carbon nanotube/ polyvinyl alcohol(PVA)/zinc oxide(ZnO) have been tested as chemical sensors and detailed study on the effect of different gas concentration and material properties on gas sensitivity is presented. Initial composites were prepared by a simple solution casting and characterized by x-ray diffraction for ZnO, Fourier transform infra-red spectroscopy (FTIR) and scanning electron microscopy (SEM) to demonstrate crystallite size of ZnO, the morphology and surface area respectively. On the other hand, MWCNT/PEO , MWCNT/PVA , MWCNT/PVA/ZnO were prepared with different loading MWCNT and ZnO. The chemical sensing properties of …

Electrodeposition Of Tin Using Tin(Ii) Methanesulfonate From Mixture Of Ionic Liquid And Methane Sulfonic Acid., Yang Kok Kee

Student Works (2010-2019)

The electrodeposition of tin from Tin(II) Methane Sulfonate (MSA) with varying concentration in air and water stable 1-butyl-1-methyl-pyrrolidinium trifluoromethanesulfonate, (BMPOTF) ionic liquid at room temperature was studied. Cyclic Voltammetry served to characterize the electrochemical behavior of tin reduction and oxidation. The diffusion coefficient of stannous ions in the mixture of BMPOTF ionic liquid and MSA based electrolyte obtained via Randles-Sevcik and Cottrell equation was 2 × 10-7 cm2/s. Electroplating on copper panel was conducted under different current densities to determine BMPOTF based tin plating solution current efficiency. Mixture of BMPOTF and MSA based tin plating solution gave current efficiency as …

Effect Of Selected Physical And Chemical Parameters On Crystal Violet Decolorization By Immobilized Laccase., Nur Atiqah Ismail

Student Works (2010-2019)

Synthetic dyes are used for coloration of various materials like textiles, leather and food. Wastewater from dyeing industries constitutes a threat to the environment as many synthetic dyes are often toxic, mutagenic and carcinogenic. Besides, light absorption is hindered by the dyes run-off creating problems to photosynthetic aquatic plants and algae. Biodegradation of waste dyestuff with enzymes provides a viable alternative compared to the often expensive physical/chemical methods. Laccase from Trametes versicolor was chosen in this study as it exhibits low substrate specificity and high ability to oxidize many pollutants which suggested its potential in wastewater treatment and bioremediation. The …

Investigation Of The Design Of A Bistable Micro-Chemical-Mechanical Device Utilizing Lateral Buckling, Susan Lyn Barnes

Honors Theses

The Gracias Laboratory at Johns Hopkins University has developed microgrippers which utilize chemically-actuated joints to be used in micro-surgery. These grippers, however, take up to thirty minutes to close fully when activated biochemicals in the human body. This is very problematic and could limit the use of the devices in surgery. It is the goal of this research to develop a gripper that uses theGracias Laboratory's existing joints in conjunction with mechanical components to decrease the closing time. The purpose of including the mechanical components is to induce a state of instability at which time a small perturbation would cause …

Risk Analysis Of Light-Frame Wood Construction Due To Multiple Hazards , Yue-Jun Yin

Dissertations, Master's Theses and Master's Reports - Open

Light-frame wood buildings are widely built in the United States (U.S.). Natural hazards cause huge losses to light-frame wood construction. This study proposes methodologies and a framework to evaluate the performance and risk of light-frame wood construction.

Performance-based engineering (PBE) aims to ensure that a building achieves the desired performance objectives when subjected to hazard loads. In this study, the collapse risk of a typical one-story light-frame wood building is determined using the Incremental Dynamic Analysis method. The collapse risks of buildings at four sites in the Eastern, Western, and Central regions of U.S. are evaluated. Various sources of uncertainties …

Three Dimensional Finite Element Simulation Of Polymer Melting And Flow In A Single-Screw Extruder : Optimization Of Screw Channel Geometry, Atakan Altinkaynak

Dissertations, Master's Theses and Master's Reports - Open

Single-screw extrusion is one of the widely used processing methods in plastics industry, which was the third largest manufacturing industry in the United States in 2007 [5]. In order to optimize the single-screw extrusion process, tremendous efforts have been devoted for development of accurate models in the last fifty years, especially for polymer melting in screw extruders. This has led to a good qualitative understanding of the melting process; however, quantitative predictions of melting from various models often have a large error in comparison to the experimental data. Thus, even nowadays, process parameters and the geometry of the extruder channel …

Advanced Mechanics Of Materials With Microstructure, Shreehari Elangovan

Dissertations, Master's Theses and Master's Reports - Open

The study of advanced materials aimed at improving human life has been performed since time immemorial. Such studies have created everlasting and greatly revered monuments and have helped revolutionize transportation by ushering the age of lighter–than–air flying machines. Hence a study of the mechanical behavior of advanced materials can pave way for their use for mankind’s benefit. In this school of thought, the aim of this dissertation is to broadly perform two investigations. First, an efficient modeling approach is established to predict the elastic response of cellular materials with distributions of cell geometries. Cellular materials find important applications in structural …

Development Of A Land Use Regression Model To Predict Nitrogen Dioxide Concentrations, Teresa Sosa

Open Access Theses & Dissertations

Air pollution is a major environmental concern in the El Paso-Juárez region. According to the Ministry of Environment and Natural Resources (Secretaría de Medio Ambiente y Recursos Naturales, SEMARNAT) the city of Juárez is one of the city's in México with the highest atmospheric levels of pollution because of its accelerated and unplanned urban growth. One air pollutant of concern is nitrogen dioxide (NO2) due to its detrimental health effects that have been associated with airway inflammation in healthy people and increased respiratory symptoms in people with asthma. Land use regression modeling is a GIS based approach that seeks to …

Harvesting Single Ferroelectric Domain Stressed Nanoparticles For Optical And Ferroic Applications, Gary Cook, J. L. Barnes, S. A. Basun, Dean R. Evans, Ron F. Ziolo, Arturo Ponce, Victor Yu. Reshetnyak, Anatoliy Glushchenko, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

We describe techniques to selectively harvest single ferroelectric domain nanoparticles of BaTiO3 as small as 9 nm from a plethora of nanoparticles produced by mechanical grinding. High resolution transmission electron microscopy imaging shows the unidomain atomic structure of the nanoparticles and reveals compressive and tensile surface strains which are attributed to the preservation of ferroelectric behavior in these particles.

We demonstrate the positive benefits of using harvested nanoparticles in disparate liquid crystal systems.

Characterization Of Atmospheric Turbulence Effects Over 149 Km Propagation Path Using Multi-Wavelength Laser Beacons, Mikhail Vorontsov, Gary W. Carhart, Venkata S. Rao Gudimetla, Thomas Weyrauch, Eric Stevenson, Svetlana Lachinova, Leonid A. Beresnev, Jony Jiang Liu, Karl Rehder, Jim F. Riker

Electrical and Computer Engineering Faculty Publications

We describe preliminary results of a set of laser beam propagation experiments performed over a long (149 km) near-horizontal propagation path between Mauna Loa (Hawaii Island) and Haleakala (Island of Maui) mountains in February 2010. The distinctive feature of the experimental campaign referred to here as the Coherent Multi-Beam Atmospheric Transceiver (COMBAT) experiments is that the measurements of the atmospheric-turbulence induced laser beam intensity scintillations at the receiver telescope aperture were obtained simultaneously using three laser sources (laser beacons) with different wavelengths (λ1 = 0.53 μm, λ2 = 1.06 μm, and λ3 = 1.55 μm). The presented experimental results on …

Gains In Knowledge And Perception Of Engineering After Participation In An Engineering Design Web-Experience Are Gender-Dependent, Kimberly Edginton Bigelow, Gail Wheatley, David Tomasko

Mechanical and Aerospace Engineering Faculty Publications

Web-based activities have the potential to teach engineering in both formal and informal science education settings, maximizing outreach efforts. To date, many activities available on the internet teach about engineering, but few allow students to truly “do” engineering.

This project utilized web animation and interaction in the design of a web-based experience focused on engineering design. In this activity, targeted toward middle school students, users played the role of engineer and engaged in the process of designing a cell phone for the older adult market. It was hoped that this web-based activity would increase participant understanding of what engineering is …

Asme Early Career Technical Journal (Front Matter), Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. -x

Development Of A Biofidelic Material Model For Brain Tissue And Its Application To The Impact Response Of The Human Head, Sandeep Kulathu, David L. Littlefield

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 1-8

Effects Of Environmental Aging On The Thermal And Mechanical Properties Of Vinyl Ester Nanocomposites, Ahmad Almagableh, P Raju Mantena

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 35-40

The Failure Characterization Of Mechanically Fastened Composite Joints, Olanrewanju Aluko, Brian S. Moore

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 19-26

Solving Coupled Systems Of Differential Equations Using The Length Factor Artificial Neural Network Method, Kevin Stanley Mcfall

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 27-34

Molecular Dynamic Simulation To Determine Temperature Dependent Young’S Modulus Of Monolayer And Bilayer Graphene Sheets, Roy Downs, Dakota Schrivener, Sachin S. Terdalkar, Joseph J. Rencis

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 41-48

Asme Early Career Technical Journal (Complete Issue), Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

An Experimental And Numerical Crashworthiness Study Of Composite Tubes, Raghawendra P S Sisodia, Nitin K. Waghmare, Anurag Dixit

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 49-56

In-Silico Simulation Of Electrostatic Charge Effects On Inhaled Aerosol Particle Deposition In The Human Lung, Mohammed Ali

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 75-79

Performance Analysis Of Micro Gas Turbine Fueled By Blends Of Biodiesel And Petroleum-Based Diesel, Farshid Zabihian, Hsiao-Wei D. Chiang, Alan S. Fung

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 66-74

Finite Element Analysis Of Bonded Composite Single-Lap Joint As A Basis For Optimizing Future Nano-Reinforcement Configurations, Gregory J. Hickman, Kuang-Ting Hsiao

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 88-96

Mathematical Models For Prediction Of Weld Bead Geometry In Gmaw Of Aluminium Alloy 7005, Reeta Wattal, Sunil Pandey

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 80-87

Analyzing Nonlinear Flexible Structures Using Perturbation Approach, Zeaid F. Hasan, Ahmad Bani-Younes

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 96-104