Engineering Commons^™

Measurement Of Refractive Index Change Of Optical Fiber Core Induced By Femtosecond Laser Scanning, Y. Han, T. Wei, Hai-Lung Tsai, Hai Xiao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We report a new method to measure the refractive index change in optical fiber core induced by femtosecond (fs) laser exposure. An in-line Fabry-Perot interferometer, serving as the measurement platform, is constructed on a commercial single-mode optical fiber by onestep femtosecond (fs) laser fabrication. A positive refractive index change is observed and measured accurately as the laser pulse energy surpasses the ablation threshold.

Polyenvi, Stephen Beard, Josh Engel, Paul Fake, Diego Flores, Alvaro Nunez, Miguel Wong

Electrical Engineering

Poor indoor air quality is a problem that is recognized by the Environmental Protection Agency (EPA) to cause health issues. In order to raise awareness of this problem, this document outlines the construction of a device that economically measures air quality through five metrics: dust, smoke, ozone, humidity, and temperature. The device integrates with a router to provide users access to information about their indoor air quality anywhere over the internet as well as local access to the data via an LCD mounted on the router. By increasing indoor air quality awareness, this device will aid users in making adjustments …

Ofdm Simulation In Matlab, Paul Guanming Lin

Electrical Engineering

The objective of this project is to demonstrate the concept and feasibility of an OFDM system, and investigate how its performance is changed by varying some of its major parameters. This objective is met by developing a MATLAB program to simulate a basic OFDM system. From the process of this development, the mechanism of an OFDM system can be studied; and with a completed MATLAB program, the characteristics of an OFDM system can be explored.

Power Losses Associated With Stand-By Chargers, Robert Peralta

Electrical Engineering

Many average households across the United States may not realize how much power is saved by simply removing the plug from the receptacle when not being used. A misconception with stand-by/portable chargers is; if a device is not connected to the charger, but the charger is still connected to the wall, then the charger will not consume power. That statement is false. The following report will demonstrate how much power is lost in an average household. When a reference is made to an average house, I will refer to a 4 bedroom single family home. The house will have an …

Electric Bicycle System, Robert Cong, Rodney Martinez, Mark Casilang, Peter Vong

Electrical Engineering

The Electric Bicycle System is a systems project that incorporates three different ways of charging a lithium-ion battery: the 120VAC wall outlet, regenerative braking, and solar power; which is used to power an electric hub motor running a bicycle. The purpose of the project is to show that it is possible and relatively simple, to build an electric bicycle by oneself. This project can be broken down into five separate categories: the lithium-ion battery, the DC-DC boost converter, the solar panel, the motor, and the motor controller. Each of these will be built upon and improved further by future students, …

Transmission Line Forecast Study, Ryan Garoogian

Electrical Engineering

Load forecasting is the procedure to predict future loading conditions on a power system. Using simulation software such as ETAP you are able to predict abnormal voltage conditions, overloading of certain equipment, as well as determine protective equipment from short circuit studies. This study consisted of a 115kV loop network with multiple loading busses and one infinite bus. There was no separate generation other than the infinite bus. As load increased from forecasting to the future voltage dropped. To restore voltage levels capacitors were added at strategic points in the system to boost the voltage back up. Preparing yourself for …

High Voltage Switched-Mode Power Supply For Three-Phase Ac Aircraft Systems, John Brewer Jr., Kamaljit Bagha

Electrical Engineering

The purpose of this senior project was to design and fabricate a proof-of-concept Three-Phase Sinusoidal Switched-Mode Inverter with a power output capability of 10 kW and nominal operating frequency of 400 Hz for AC aircraft system applications. This senior project report includes a thorough discussion and presentation of the inverter system background, requirements, design, construction, and testing processes.

Energy Harvesting From Exercise Machines Cal Poly Recreation Center Implementation, Justin Arakaki, Praveen Lawrence, Audrey Nakamura

Electrical Engineering

As Cal Poly moves towards an environmentally friendly campus, the Energy Harvesting from Exercise Machines (EHFEM) project looks to generate a new source of renewable energy to help power the Cal Poly Recreation Center. The project focuses on retrofitting exercise machines to generate electricity. As of December 2009, Audrey Nakamura, Justin Arakaki, and Praveen Lawrence developed a design which allows the contribution of electricity generated from multiple exercise machines into the power grid.

The project will require an investigation of retrofitted machine designs by Cal Poly students and commercially available products and systems. The information obtained from the product research …

Design Of A High-Low Unipolar Pulse Width Modulated Inverter, Danny Li, Christian Ramos

Electrical Engineering

This senior project report describes the process of designing a unipolar inverter. This high low, unipolar inverter utilizes switches in which a pair operates in high frequency while a second pair operates in low frequency. The purpose of this project is to convert a range of high DC voltage and convert it to an AC output voltage of 120 Vrms with a power rating of 100 W. Nonetheless, this particular unipolar method of implementing pulse width modulation results in harmonics at multiples of the fundamental frequency leading to easier filtering. However, the switching loss increases because of the complex switching …

Energy Harvesting From Exercise Machines: Bike Buck-Boost Converter, Monroe Diamond, Brian Vuong

Electrical Engineering

This project is a continuation of previous senior projects’ work on Energy Harvesting from Exercise Machines (EHFEM). EHFEM seeks an alternative DC to DC converter to function within the existing exercise bike system. Implementing this new DC to DC converter aims to avoid previous complications other groups encountered, such as only running at low load currents, exceeding an input threshold voltage to begin operation, and performing at low efficiency. In developing this self‐generating exercise bike, Cal Poly wishes to incorporate an array of energy‐harvesting exercise machines in its Recreation Center expansion scheduled for completion in 2012.

Observations Of Temporal Group Delays In Slow-Light Multiple Coupled Photonic Crystal Cavities, S. Kocaman, Xiaodong Yang, J. F. Mcmillan, M. B. Yu, D. L. Kwong, C. W. Wong

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We demonstrate temporal group delays in coherently coupled high- Q multicavity photonic crystals, in an all-optical analog to electromagnetically induced transparency. We report deterministic control of the group delay up to 4x the single cavity lifetime in our room-temperature chip. Supported by three-dimensional numerical simulations and theoretical analyses, our multipump beam approach enables control of the multicavity resonances and intercavity phase, in both single and double transparency peaks. The standing-wave wavelength-scale photon localization allows direct scalability for chip-scale optical pulse trapping and coupled-cavity quantum electrodynamics.

Quantum Inspired Pso For The Optimization Of Simultaneous Recurrent Neural Networks As Mimo Learning Systems, Bipul Luitel, Ganesh K. Venayagamoorthy

Electrical and Computer Engineering Faculty Research & Creative Works

Training a single simultaneous recurrent neural network (SRN) to learn all outputs of a multiple-input-multiple-output (MIMO) system is a difficult problem. a new training algorithm developed from combined concepts of swarm intelligence and quantum principles is presented. the training algorithm is called particle swarm optimization with quantum infusion (PSO-QI). to improve the effectiveness of learning, a two-step learning approach is introduced in the training. the objective of the learning in the first step is to find the optimal set of weights in the SRN considering all output errors. in the second step, the objective is to maximize the learning of …

Final Design Report: Vibration Table For Cvbt- Vt4 Design Team, Thomas Bevan, Matthew Laurino

Mechanical Engineering

CVBT (Center for Vocational Building Technology) teaches villagers in Northeastern Thailand how to make various concrete products. Many of these products require the use of a vibration table in order to remove air and water trapped within the concrete. Removal of these voids improves the outside surface of the molded concrete, and also allows the use of a lower water to cement ratio, allowing a much stronger finished product. The currently used vibration table (VT3) has several disadvantages associated with it, which the new table (VT4) eliminates. Compared with the VT3, the VT4 has a more rigid tabletop and improved …

Edwards Automation Final Project Report, Benjamin (Ben) Johnson, Joel Masters, Matthew (Matt) Stewart

Mechanical Engineering

The body of this work has been created for Edwards Lifesciences in conjunction with senior project requirements. As such, the information produced and contained within is under a non‐disclosure agreement. As per request by sponsor, the body of the work will not be submitted to any outside parties, and the title page will serve as proof of completion.

Human Powered Helicopter, Brenton Haven, Daniel Hudson, Eli Knight

Mechanical Engineering

Fall of 2009, The Cal Poly Aircraft Construction club restarted Cal Poly's quest for the Sikorsky prize. The Sikorsky prize rewards the first a human powered helicopter to sustain controlled hover for one minute without stored energy. Throughout the 1980’s, Cal Poly made three attempts; the most successful being the DaVinci III. Also, the DaVinci III was the first ever publically recognized successful human powered helicopter to leave the ground. This scope of this project is to improve the DaVinci III fuselage and drivetrain for the DaVinci IV. The DaVinci IV adopts the DaVinci III system layout and improves both …

Solar Array Suspension Mechanism Final Design Report For Atk Space, Alex Gould, Randon Kruse, Jeremy Graul, Patrick Barney

Mechanical Engineering

The purpose of this project is to improve the existing Solar Array Suspension Mechanism used by ATK Space for the manufacturing and testing of deployable solar arrays. The current system requires too much time to operate and has too many removable parts that may fall and damage the solar arrays. Through the design and verification process the team successfully constructed a quick connecting suspension mechanism that requires no tools to use and has no removable parts. The final design includes the existing force gauge and large adjustment bars used by ATK Space with the addition of a compression spring adjustment …

Strider, Eric Johnson, Alex Trask, Ricardo Garcia

Mechanical Engineering

No abstract provided.

Cal Poly Formulasae Engine Development, Matthew Ales, Rafael Mendoza, Mitchell (Mitch) Thomas, Leon Vinokurov

Mechanical Engineering

This project, engine development, was sponsored by Cal Poly FormulaSAE. The FormulaSAE team proposed this project in order to have a more reliable and more powerful engine for their car, to improve their overall performance at their competition. The baseline output of the engine is 37 hp and 24 lb-ft of torque. The goal of this project was to increase the output to 45 hp, to meet requirements determined by a trade study. We planned to increase the engine’s output using several strategies.

We evaluated all potential design decisions using a Ricardo WAVE model. Ricardo WAVE is a software tool …

Cisco Data Center Energy Efficiency, Brandy Sizemore, Travis Snook, William Neumeister

Mechanical Engineering

The goal of the Cisco Systems data center efficiency study is to improve the energy efficiency of Lab C in Cisco’s Building 7. The main phases involved are research, energy analysis, CFD simulations, and lab testing. The first part of the project entailed research in the data center field. This included attending two lectures provided by Cisco, visiting the annual Silicon Valley Data Center Energy Efficiency Summit hosted by Network Appliance, going on many data center tours, and taking a 3-day 6Sigma CFD training class. Next, the 1st Law of Thermodynamics was applied to the CRAH (computer room air handler) …

Medtronic Universal Crimping Machine, Justin Ginochio, Andrew Hanson, Zachary (Zach) Dieterle

Mechanical Engineering

This project is geared towards the redesign and implementation of a crimping tool for use in the manufacturing of catheters produced by Medtronic Inc. Catheters require two steering cables to maneuver the end of the catheter through the body. The steering cables have a sleeve that is crimped onto their end in order to hold the cable in place inside the catheter steering handle. The current crimping tool, designed by Astro Tool Corp, has a few problems associated with its design. Additionally we are trying to get rid of a step in the manufacturing process that involves the adhesive, cyanoacrylate, …

Guidable Motorcycle Headlight, Billie B. Fritz, Toby J. Lloyd

Mechanical Engineering

Motorcycling at night is an inherently dangerous situation and is compounded by poor illumination of the roadway when cornering through a turn. Due to stationary headlamps geometry being designed for upright riding position, cornering a motorcycle causes the illumination of the forward path to be decreased significantly. The goal of this project is to develop a lighting system that will improve road illumination for riders at night using guidable lights that deflect prior to and during a turn. In addition to developing a working prototype, this project’s intent is to work in conjunction with a partner from the school of …

Composite Suspension For Formula Sae Vehicle, Reid Olsen, Andrew Bookholt, Eric Melchiori

Mechanical Engineering

This senior project report describes how a redesign of the 2008 Cal Poly Formula SAE vehicle's suspension components was conducted using carbon fiber components.

Water Conservation Device, Michael Eichermueller, Michael (Mike) Moren, Florian Liefhold, Philipp Von Vopelius, Christoph Wagner, Tommy Stendel, Jacob Venzor

Mechanical Engineering

The Water Conservation Project (WCP) is a design concept to reduce the water consumption on startup of a shower. Every time a shower is started with a conventional tank water heater, approximately 7.5 liters of cold water is flushed down the drain without being used before the hot water reaches the faucet. For a city the size of San Luis Obispo, this amounts to approximately 121 million liter of water per year. The main goal of this project was to devise a way to conserve the cold water that is contained in the hot water pipes before every shower. Ultimately, …

Equine Hoof Block, Aaron Murano, Jason Smith

Mechanical Engineering

No abstract provided.

Class-D Power Amplifier, Joseph Maldonado, Jeovany Vega

Electrical Engineering

No abstract provided.

Micro Forest Fire Detection, John Cape

Electrical Engineering

No abstract provided.

An Expandable Micromotor Dc Drive System, Michael Ruelan, Justin Gragg

Electrical Engineering

This report documents the design phases and fabrication of an expandable micro-motor DC drive system. This project illustrates that a flexible range of output power demands can be met from a small DC micro-motor drive unit with the use of power electronics.

In this project miniature DC micromotor drives, each capable of drawing up to 5.5 amps rated current (5 amps due to the utilization of a 5 amp fuse), were designed as card inserts that can be conveniently inserted in parallel in to a cardholder within the console. The “insert” feature allowed our console to successfully draw up to …

Uav Pirates And Silentrack Integration, Travis Dean, Hushnak Singh, Ashley Wager, Matthew (Matt) Woolridge

Electrical Engineering

The integration of the UAV pirating system with the SilenTrack video tracking system will allow the combined system to automatically identify and track a suspicious air vehicle visually as well as identify and decode the RF control signal. Once a threat has been identified, the system will execute an algorithm to associate each control channel with the corresponding flight control surface. Once the control channels have been decoded the user can use a hand held radio controller to maneuver the drone which is now under their command.

Circular Polarized Splatch Antenna, Cynthia Truong

Electrical Engineering

The Splatch Antenna combines excellent performance and cost-effectiveness into an antenna package that can be integrated. The goal of this project is to figure out how to connect two Splatch antennas to realize a Circular Polarized (CP) antenna. The advantage of CP versus linear polarization is that CP eliminates polarization mismatch losses caused by Faraday’s rotation.

Solar Panel Tracker, Andrew Hsing

Electrical Engineering

This project will be a design and implementation of a polar single axis solar panel tracker. It will have a fixed vertical axis and an adjustable horizontal motor controlled axis. This setup is similar to an office swivel chair. The tracker will actively track the sun and change its position accordingly to maximize the energy output. To prevent wasting power by running the motor continuously, the tracker will correct it's position after 2 to 3 degrees of misalignment. The sensors will compare the light intensities of each side and move the panels until the tracker detects equal light on both …