Engineering Commons^™

Comprehensive Model Of Alkali-Salt Deposition In Recovery Boilers, Richard A. Wessel, Larry Lin Baxter 8507091

Faculty Publications

Algorithms for alkali-salt deposition have been implemented into a comprehensive model for recovery boilers. The model includes (a) mechanisms for particle formation and chemistry, (b) particle deposition and adhesion, and (c) deposit thermal properties. These algorithms are fully coupled with models for turbulent flow, black liquor combustion, and heat transfer in the boiler. Model predictions for particle deposition in the convection pass are presented for a Babcock & Wilcox recovery boiler. This work is part of an ongoing project sponsored by the U.S. Department of Energy to demonstrate an improved ability to anticipate ash behavior with changes in fuel composition, …

Corp - A Method Of Concatenation And Optimization For Resource Reservation Path In Mobile Internet, Kyounghee Lee, Myungchul Kim, Samuel T. Chanson, Chansu Yu, Jonghyun Lee

Electrical and Computer Engineering Faculty Publications

Existing research related to RSVP with mobility support has mainly focused on maintaining reservation state along the routing path, which changes continuously with the movements of mobile host (MH), without much overhead and delay. However, problems such as deepening RSVP's inherent scalability problem and requiring significant changes in the existing network infrastructure have not been adequately addressed. In this paper, we propose a new approach, known as Concatenation and Optimization for Reservation Path (CORP), which addresses these issues. In CORP, each BS pre-establishes pseudo reservations to its neighboring BSs in anticipation of the MH's movement. When the MH moves into …

An All-Digital Clock-Smoothing Technique—Counting-Prognostication, Xiaoyi Qin, Hansheng Wang, Lieguang Zeng, Fuqin Xiong

Electrical and Computer Engineering Faculty Publications

This article presents a novel universal all-digital clock-smoothing technique - counting-prognostication. Operation principles, performance analysis, and comparisons are given. Analysis and measurement results show that this technique can efficiently smooth jitter and wander for a wide pull-in range and pull-out range, and jitter accumulation is small. A cycle-varying counting-prognostication method, which decreases pull-in time, is also suggested.

Enterprise Integration With Erp And Eai, Jinyoul Lee, Keng Siau, Soongoo Hong

Research Collection School Of Computing and Information Systems

The Integration of enterprise with the ERP (enterprise resource planning) and EAI (enterprise application integration) is discussed. The ERP supports the centralized business strategy while EAI accomodates the decentralized business processes. The changes brought in by the internet technology led the internalization and extrenalization to move together. The agility and the flexibility in the organizations would be achieved by a greater degree of communication, coordination and cooperation in human factors and information technologies. The enterprise integration fulfills the needs of both internal business processes and external customer by internalization and externalization.

Real Time Dynamic Trajectory Smoothing For Uninhabited Aerial Vehicles, Erik Anderson, Randal Beard, Timothy W. Mclain

Faculty Publications

Sponsorship: AFOSR, DARPA. This paper presents a real-time, feasible trajectory generation algorithm for unmanned air vehicles (UAVs) flying through a sequence of waypoints. The algorithm produces extremal trajectories that transition between straight-line path segments in a time-optimal fashion. In addition, the algorithm can be configured so that the dynamically feasible trajectory has the same path length as the straight-line waypoint path. Implementation issues associated with the algorithm are described in detail. Simulation studies show the effectiveness of the proposed method.

Network Lifetime Extension, Power Conservation And Interference Suppression For Next Generation Mobile Wireless Networks, Amer Catovic

Dissertations

Two major focus research areas related to the design of the next generation multihop wireless networks are network lifetime extension and interference suppression. In this dissertation, these two issues are addressed.

In the area of interference suppression, a new family of projection multiuser detectors, based on a generalized, two-stage design is proposed. Projection multiuser detectors provide efficient protection against undesired interference of unknown power, while preserving simple design, with closed-form solution for error probabilities. It is shown that these detectors are linearly optimal, if the interference power is unknown.

In the area of network lifetime extension, a new approach to …

A Reactive Melt Modification Of Polyethylene Terephthalate, Rahul Ramesh Dhavalikar

Dissertations

This work investigates the structural and chemorheological modification of polyethylene terephthalate in the melt phase with low molecular weight multifunctional glycidyl compounds as reactive additives. Polyethylene terephthalate undergoes chain extension and/or branching reactions with the additives that result in modified rheological properties suitable for certain polymer processing operations such as extrusion blow molding or extrusion foaming to low densities.

Among five different low MW difunctional and trifunctional epoxy compounds, triglycidyl isocyanurate is shown to be an efficient reactive melt modifier for commercially available polyethylene terephthalate polymers. Its stability at the polyethylene terephthalate melt temperatures is confirmed offline through thermogravimetric and …

Joint Buffer Management And Scheduling For Input Queued Switches, Dequan Liu

Dissertations

Input queued (IQ) switches are highly scalable and they have been the focus of many studies from academia and industry. Many scheduling algorithms have been proposed for IQ switches. However, they do not consider the buffer space requirement inside an IQ switch that may render the scheduling algorithms inefficient in practical applications.

In this dissertation, the Queue Length Proportional (QLP) algorithm is proposed for IQ switches. QLP considers both the buffer management and the scheduling mechanism to obtain the optimal allocation region for both bandwidth and buffer space according to real traffic load. In addition, this dissertation introduces the Queue …

Acoustical Characterization And Parameter Optimization Of Polymeric Noise Control Materials, Emile N. Homsi

Dissertations

The sound transmission loss (STL) characteristics of polymer-based materials are considered. Analytical models that predict, characterize and optimize the STL of polymeric materials, with respect to physical parameters that affect performance, are developed for single layer panel configuration and adapted for layered panel construction with homogenous core. An optimum set of material parameters is selected and translated into practical applications for validation.

Sound attenuating thermoplastic materials designed to be used as barrier systems in the automotive and consumer industries have certain acoustical characteristics that vary in function of the stiffness and density of the selected material. The validity and applicability …

Numerical And Experimental Investigation Of Dry Particle Coating, Ajit Mujumdar

Dissertations

Dry particle coating is an emerging field in the industries that deal with particulate products and powder processing. Compared to the widely reported experimental studies of the dry particle coating, the theoretical modeling of such processes is found to be less comprehensive. The work presented in this thesis is an attempt to fill this gap.

The first part of the dissertation aims at the numerical investigation of the hybridization system (Nara Machinery, Tokyo, Japan). The flow behavior of different materials processed in this device is analyzed using three-dimensional Discrete Element Method (DEM) as well as the computational fluid dynamics (CFD) …

Packet Data Communications Over Coded Cdma With Hybrid Type-Ii Arq, Seokhyun Yoon

Dissertations

This dissertation presents in-depth investigation of turbo-coded CDNIA systems in packet data communication terminology. It is divided into three parts; (1) CDMA with hybrid FEC/ARQ in deterministic environment, (2) CDMA with hybrid FEC/ARQ in random access environment and (3) an implementation issue on turbo decoding.

As a preliminary, the performance of CDMA with hybrid FEC/ARQ is investigated in deterministic environment. It highlights the practically achievable spectral efficiency of CDMA system with turbo codes and the effect of code rates on the performance of systems with MF and LMMSE receivers, respectively. For given ensemble distance spectra of punctured turbo codes, an …

Evaporating Crossflow Sprays In Gas-Solid Flows, Guangliang Liu

Dissertations

Injection of evaporating sprays into gas-solid flows is encountered in many engineering processes such as energy production industry and chemical industry. The phenomenon involves phase change, three-phase interactions, heat and mass transfer. All of these characteristics control the process efficiency, pollutant production and product quality. However, very limited studies are available on the evaporating spray jets in gas-solid flows, especially on the spray evaporation rate within a gas-solid medium. A combined study of experiments and theoretical analysis has been carried out here to investigate the fundamental mechanism of evaporating Crossflow spray jets in gas-solid flows.

In this study, in addition …

Study Of Vapor/Gas Permeation Using Thin Immobilized Liquid Membrane, Gordana Obuskovic

Dissertations

To improve liquid membrane selectivity and stability for removal of vapor and gases from a gas stream, a thin immobilized liquid membrane (ILM) has been studied. Low vapor pressure liquid solvent/solutions were immobilized in part of the micropores of a hydrophilic, hydrophobic or ceramic hollow fiber substrate. To prepare such thin ILMs, three approaches were used: evaporation of the a volatile solvent; acrylic acid-grafted hollow fibers providing a thin hydrophilic layer; pressurization technique.

For removal of volatile organic compound (VOC), a thin ILM of silicone oil incorporated in the micropores of a hydrophobic hollow fiber with a silicone rubber coating …

Shear Strengthening Of Rc Beams Using Carbon Fiber Reinforced Polymer Laminates, Zhichao Zhang

Dissertations

Shear failure is catastrophic and occurs usually without advanced warning, thus it is desirable that the beam fails in flexure rather than in shear. Many existing reinforced concrete (RC) members are found to be deficient in shear strength and need to be repaired. Deficiencies occur due to several reasons such as insufficient shear reinforcement or reduction in steel area due to corrosion, increased service load, and construction defects. Externally bonded reinforcement such as Carbon Fiber Reinforced Polymer (CFRP) provides an excellent solution in these situations.

In order to investigate the shear behavior of RC beams with externally bonded CFRP shear …

Robust And Efficient Video/Image Transmission, Xi Min Zhang

Dissertations

The Internet has become a primary medium for information transmission. The unreliability of channel conditions, limited channel bandwidth and explosive growth of information transmission requests, however, hinder its further development. Hence, research on robust and efficient delivery of video/image content is demanding nowadays.

Three aspects of this task, error burst correction, efficient rate allocation and random error protection are investigated in this dissertation. A novel technique, called successive packing, is proposed for combating multi-dimensional (M-D) bursts of errors. A new concept of basis interleaving array is introduced. By combining different basis arrays, effective M-D interleaving can be realized. It has …

Deposition And Characterization Of Magnetron Sputtered Bcc Tantalum, Anamika Patel

Dissertations

The goal of this thesis was to provide scientific and technical research results for developing and characterizing tantalum (Ta) coatings on steel substrates deposited by DC magnetron sputtering. Deposition of tantalum on steel is of special interest for the protection it offers to surfaces, e.g. the surfaces of gun barrels against the erosive wear of hot propellant gases and the mechanical damage caused by the motion of launching projectiles. Electro-plated chromium is presently most commonly used for this purpose; however, it is considered to be carcinogenic in its hexavalent form. Tantalum is being investigated as non-toxic alternative to chromium and …

The Development Of A Biodegradable Scaffold For A Tissue Engineered Heart Valve, Thomas Adam Alheidt

Theses

In the current state of medical technology, there exists the need for a quality medical device to replace a failing heart valve. Presently, mechanical valves as well as donor tissue valves, either from humans or animals are used to replace failing heart valves. These valves although they can operate in the heart satisfactorily are not equal to the body replacing its own valve. Tissue Engineering in simple terms is the field of helping the body replace its own failing organ. In scientific terms, Tissue Engineering is a relatively young field, a majority of the major advancements have come in the …

Firewall Interface For Java Ftp Smtp And Http Servers, Ratan Kumar Erukulla

Theses

The objective of my thesis is to develop a firewall interface for FTP, HTTP and SMTP servers. A firewall interface is a graphical user interface (GUI) to configure the properties of the server. Using this interface, we can spy a user, block and unblock the IP address of a client, display statistics of user and server. We can track all the user actions while he is connected to the server. These actions are logged and based on the log data we can deny access to users performing illegal operations. All the servers and interfaces are written in Java. Java was …

In Situ Laser Etch-Depth Monitoring Of The Deep Reactive Ion Etching Process, Yuki Imura

Theses

A laser-based method for measuring feature thickness during the deep reactive ion etching process is investigated. Interference occurs between laser beam reflections from the mask surface, the mask/silicon interface, and the exposed silicon surface of a process wafer. Information from this interference signal allows the etch process to be characterized. Three methods are investigated: laser-on-SiO₂, laser-on-photoresist, and laser-on-both SiO₂ and silicon at a mask edge.

The measured data from these experiments are found to be in good agreement with theoretical calculations. Differences in reflected beam amplitude and interference fringe frequency represent well the differences SiO₂ and …

Vlsi Design Of Stability Routing Protocol For Sensors In Wireless Mobile Ad-Hoc Networks, Vishnu M. Mandava

Theses

This thesis gives a detailed description of the Application specific integrated circuit (ASIC) design of Stability routing protocol for sensors in mobile ad-hoc networks. The Stability routing protocol is based on the signal strength and position components during data transmission while considering sensors in an ad-hoc network. A general ad-hoc network has unpredictable and variable mobility patterns therefore the signal strength criteria is adopted for routing. Signal strength criteria has been proved to be efficient for communication between the mobile nodes without any data loss. In this thesis an architecture for a processor implementing stability routing protocol for effective communication …

Numerical Study Of Pneumatic Conveying Of Powders, Muhammad Mushahid Rafique Quereshi

Theses

The dense phase mode may be advantageous over the dilute phase mode, for some pneumatic conveying problems, because it causes less erosion of the pipeline, less attrition of the material, requires less dust collection and is effective even for smaller pipe diameters. The objective of this study is to numerically determine the parameters that govern the formation slugs in dense phase conveying. The distributed Lagrange multiplier/fictitious domain method (Glowinski et al. 1998 and Singh et al. 2000) is used to perform direct simulations of the motion of solid and gas phases in pipes with rectangular cross-sections. In this approach the …

Integrating Tolerances In G And M Codes Using Neural Networks, Vijay Kumar Sundareshan

Theses

Continuous integrated solutions from CAD down to the preparation of NC programs were developed in the recent years. However, if tolerances should be considered, the interaction of human experts is still necessary. A way to fill this gap in the production process is shown in this thesis. The study builds a relationship between the given design tolerances and including these tolerances in machining by generating respective G and M codes. The study focuses on physical phenomena and their inter-relationship while manufacturing. For example how the speed of machining, torque, power, depth of cut, etc. influences machining under specified tolerances. Artificial …

Electrohydrodynamical Manipulation Of Particles Based On Dielectrophoresis, Oleksii Vasylyschuk

Theses

The movement of matter in a non-uniform electric field, termed dielectrophoresis, is of interest to scientists of various branches: physics, chemistry, engineering, and life science. To chemists and physicists it is a science of many varied phenomena. To engineers it is a source of new and useful techniques for separating materials or improving materials’ behavior. To ecologists it provides a major means of minimizing pollution. To life scientists it offers new ways to study and manipulate cells and their subparticles, and to help unravel the nature of living systems.

The purpose of this thesis is to concentrate on some aspects …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Nov. 01 – Jan. 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

The design of the new apparatus for oxygen measurement/calibration has been completed. This new apparatus shall be of great importance for the UNLV researchers to conduct the research work in the campus.

Implementation Of A Two-Dimensional Discrete Element Method To Describe Granular Materials Composed Of Elliptical Cohesionless Particles, Juan Jose Martinez Alvez

Theses

This work is aimed at developing a discrete element simulation that models the contact between elliptical grains or particles in granular materials. The goal is to implement an algorithm to carry out collision detection between ellipses as well as ellipsoidal objects. The practical issue here is that the real shape of macroscopic grains can be approximated better using elliptical curves than using spherical curves. In addition, the simulation model will also be valid for spheres, since these objects are special cases of ellipsoids.

An accurate contact detection algorithm was investigated by means of two different formulations. The first formulation determines …

Liquid-Liquid Mixing In Stirred Tanks With Varying Liquid Depths, Sunil Mehta

Theses

Considerable attention has been devoted in the past to the determination of the minimum agitation speed, N_cd, required for the complete dispersion of two immiscible liquids in mechanically stirred tanks. When this situation is achieved the dispersed phase is no longer present as a distinct layer, such as a light oil phase above an aqueous solution, but becomes completely dispersed, in the form of droplets, throughout the continuous phase. The achievement of the dispersed state is of significant importance in many industrial operations. Nevertheless, the effect on N_cd of a number of operating variables remains poorly understood. …

Storage Allocation In Bounded Time, Sharath Reddy Cholleti

All Computer Science and Engineering Research

The correctness of a real-time system is very much dependent on the time at which a specific task is completed. Hence, satisfying a storage allocation request within bounded time is important. Fragmentation of the heap after repeated allocations and deallocations is a major issue for real-time systems, as most allocators depend on garbage collection for defragmentation of the heap, which might not finish in time to honor deadlines. We present the storage requirement for a defragmentation-free binary-buddy allocator. We also study a localized defragmentation algorithm to satisfy a single allocation request, within bounded time, instead of requiring defragmentation of the …

Evaluation Of Intrusion Detection Systems With Automatic Traffic Generation Programs, Friday Bassey Akpan

Theses

In this master's thesis work, a program was developed using the Perl programming language to enable user defined attack programs to run automatically. A similar program was also developed for background traffic. With this program, the different features of the Nmap exploration and scanning tool were exploited to build scenarios of attacks.

Automated scenarios of attacks running in to the order of hundreds were developed. Also, different sets of automated stealthy attacks scenarios running in to the order of hundreds were developed using the timing modes, stealthy scans and scan delay features of Nmap.

These automated attacks scenarios were employed …

Characterization And Corrosion Of Bcc-Tantalum Coating Deposited On Aluminum And Steel Substrate By Dc Magnetron Sputtering, Chirag Joshi

Theses

Tantalum is one of the most versatile highly refractory corrosion-resistant metals. Tantalum coating can be used as an effective corrosion barrier if it is continuous, free from defects and it adheres well to the substrate. A DC magnetron sputtering technique was used to deposit tantalum on aluminum and steel. X-ray diffraction measurements revealed that the tantalum films produced by sputtering had two crystallographic structures: a body centered cubic α-phase and a metastable tetragonal β-phase. Tough and ductile alpha phase tantalum is preferred over the hard and brittle beta phase tantalum, as a protective coating. Alpha phase coatings were successfully deposited …

Computer Simulation Of Automotive Disc Brake Noise, Vadims Milovs

Theses

Disc brake noise continues to be a major concern throughout the automotive industry despite efforts to reduce its occurrence. Many articles are written on this subject, but there still is no agreement on what exactly causes disc brake noise and what part of the braking system is responsible for it.

The goal of current research was to build a simplified but inclusive mathematical model of a disc brake system and investigate it using Matlab software. The twodimensional model including damping, Stribeck effect and stick-slip friction was built.

The model is unique in a way that all the similar models have …