Engineering Commons^™

Relative Humidity And Temperature Effects On Tensile Strength Of Edible Protein And Cellulose Ether Films, A. Gennadios, H. J. Park, Curtis L. Weller

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The effect of relative humidity and temperature on tensile strength of two types of protein-based [corn zein (CZ) and wheat gluten (WG)] and two types of cellulosic [methylcellulose (MC) and hydroxypropyl cellulose (HPC)] hydrophilic edible films was investigated.

Property Modification Of Edible Wheat, Gluten-Based Films, A. Gennadios, Curtis L. Weller, R. F. Testin

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Procedures were developed to produce edible wheat, gluten-based films. A film was produced as a standard. Five additional films were then produced by modifying the initial film-forming solution. Modifications included changing the plasticizer, partially substituting wheat gluten with soy protein isolate and corn zein, and incorporating two acetylated monoglyceride products. All films were characterized by measuring selected mechanical properties, and permeabilities to water vapor and to oxygen. Comparison of the films, in terms of their measured properties, indicates ways to improve the overall performance of the standard film as a potential packaging material. A main limitation of all of the …

Grain Suffocation Hazards, Larry R. Piercy

Agricultural Engineering Extension Updates

Grain and feed storage systems are a common sight on Kentucky farms and usually present no particular hazard for the user. However, flowing grain or grain that is caked or spoiled can pose a serious threat of entrapment and suffocation. To protect yourself and your family, you need to become familiar with this potential hazard.

Generation And Legal Regulation Of Odors Form Animal Manures, J. L. Taraba, R. M. Williams

Agricultural Engineering Extension Updates

The present trend of animal and dairy product producers is toward total confinement facilities and larger animal herds. Generally the rewards to the producer for these practices are higher economic returns which result from higher feeding efficiencies and better quality products. However, total confinement is not without problems that were previously not present or were minimal in nature when animals were maintained in fields. Confinement facilities have a greater impact on environmental quality of both water and air. Presently, one of the major problems facing animal and dairy product producers is odor production. The greatest number of complaints concerning environmental …

Laws And Regulation Impacting Livestock Wastes In Kentucky, J. L. Taraba, R. M. Williams

Agricultural Engineering Extension Updates

In recent years, the number of laws and regulations prescribing the rules for everyday life seem to be ever more complex and pervasive. Changing farming methods, expansion of the urban community and increasing public environmental concerns have increased the agricultural producer's need to think more seriously about his method of livestock waste disposal. Laws, regulations, practices, standards and ordinances range from the obvious (solid waste management) to the not so obvious (protection of endangered species). The public has protection from the farmers (discharge permits) and the farmer has protection from the public (Right to Farm laws). The following is an …

Solid Livestock Waste Regulatory Requirements, J. L. Taraba, W. D. Thom, Anthony J. Pescatore, R. M. Williams

Agricultural Engineering Extension Updates

Proper management and utilization of livestock waste can be a significant contribution to the economic well being of a livestock enterprise, since the wastes have considerable economic value if properly utilized. When returned to the soil as fertilize or soil conditioner, the value as a nutrient source has been will established. More recently, processed livestock wastes have been utilized as a high protein feed additives. Livestock waste should be considered a resource to be utilized rather than a disposal problem.

Kentucky State Agencies With Water Responsibilities, Joseph L. Taraba

Agricultural Engineering Extension Updates

On the following pages are a list of Kentucky state government agencies that have responsibilities and programs that relate to water in the areas of quality, health, supply, financing, flood control, recreation and tourism. For local programs on water, one of these agencies might be able to supply material, personnel or other programming information that would aid of your local extension water issue goals.

Rio Mimbres Acequia Systems: An Oral History, Neal W. Ackerly

Books

This volume contains transcripts of interviews with various residents collected during the 1993 field phase of the survey of acequia systems in the Mimbres Valley. As noted in Volume 1, additional interviews were conducted with other residents, but were not recorded. Accordingly, no transcript of these interview sessions cannot be included here.

The individuals interviewed, as well as the abbreviated names appearing in these transcripts, included John VonTress (JVT, age 57), Regis McSherry (RM, age 67), Sam Grijalva (age 73), Charles Disert (age 84), and Horace Bounds (HB, age 90). Vesta McSherry, appearing as VM in transcripts, provided additional information …

Multiple Sample Cryostat For The Determination Of Superconductor Properties, G. Burnside, Roger M. Hawk, Paul C. Mcleod

Journal of the Arkansas Academy of Science

Cryostats which are currently used to characterize the properties of superconductors between 4 K and 100 K are primarily single sample devices. The purpose of this paper is to present an instrument design which can hold up to five (5) one cm. diameter samples at a stable temperature (+ /-0.1K) within the above range specified while measurements of the sample properties are made.

Sputter Deposition And Thallination Of Ti-Ba-Ca-Cu-O Superconducting Thin Films, T. H. Dhayagude, S. S. Ang, W. D. Brown

Journal of the Arkansas Academy of Science

Thallination techniques used for the fabrication of sputter-deposited TI2Ba2CaCu 2Ox and TI2Ba2Ca2Cu3Ox superconducting thin films were investigated. Differences in elemental composition of precursor Ba-Ca-Cu-O sputtering targets were found to yield different superconducting phases. Thallination conditions which yielded transition temperatures as high as 122 K for samples annealed in air are described. Finally, reactive ion etching of films using a mixture of chlorine and argon gases is discussed.

A New Technique To Decompose Closely Spaced Interface And Bulk Trap States Using Temperature Dependent Pulse-Width Deep Level Transient Spectroscopy Method: An Application To Pt/Cds Photodetector, C. W. Wang, Cheng-Hsiao Wu, Jack L. Boone

Electrical and Computer Engineering Faculty Research & Creative Works

A novel method is presented here to experimentally decompose nonexponential capacitive transients into the appropriate components from the closely spaced deep trap states. Using temperature dependent pulse-width deep level transient spectroscopy (TDP-DLTS) technique, we show for the first time that two bulk trap states and one continuously distributed interface states in (Pt/CdS) photodiodes can be successfully separated. The basic principle is to set the applied pulse width to follow an averaged temperature-dependent capture time constant and divide the DLTS spectrum. In the example of Pt/CdS photodiodes, we show that all physical parameters including thermal activation energies, capture cross sections, and …

The Influence Of Matrix Microstructure, G. M. Vyletel, J. E. Allison, David C. Van Aken

Materials Science and Engineering Faculty Research & Creative Works

The low-cycle and high-cycle fatigue behavior and cyclic response of naturally aged and artificially aged 2219/TiC/15p and unreinforced 2219 Al were investigated utilizing plastic strain-controlled and stress-controlled testing. The cyclic response of both the reinforced and un-reinforced materials was similar for all plastic strain amplitudes tested except that the saturation stress level for the composite was always greater than that of the unreinforced material. The cyclic response of the naturally aged materials exhibited cyclic hardening and, in some cases, cyclic softening, while the cyclic response for the artificially aged materials showed no evidence of either cyclic hardening or softening. The …

Analytical Guidance Laws And Integrated Guidance/Autopilot For Homing Missiles, S. N. Balakrishnan, Donald T. Stansbery, J. H. Evers, J. R. Cloutier

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An approach to integrated guidance/autopilot design is considered in this study. It consists of two parts: 1) recognizing the importance of polar coordinates to describe the end game in terms of problem description and measurement acquisition, the terminal guidance problem is formulated in terms of polar coordinates; 2a) through the use of the state transition matrix of the intercept dynamics, a closed form solution for the transverse command acceleration is obtained; and 2b) through a commonly used approximation on time-to-go and a coordinate transformation, a family of proportional navigation optimal guidance laws is obtained in a closed form. A typical …

Dual Purpose Fuze, Paul Nicholas Worsey

Mining Engineering Faculty Research & Creative Works

A dual purpose fuze for a projectile which can activate a quantity of material selected from a group including high explosive, low explosive, propellant and pyrotechnic compounds. The fuze includes a charge holder having a socket therein facing the quantity of material to be activated. A fuze charge located in the socket has a depression in it so formed as to cause the fuze charge to explode in a jet directed outwardly from the socket of sufficiently high energy to activate a high explosive in a high explosive projectile, the fuze charge being sufficiently small to prevent rupture of containment …

Advanced Graphics Zoom In On Operations, Max Darwin Anderson, Hardy J. Pottinger, C. M. Schroeder

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Battery Energy Storage Technologies, Max Darwin Anderson, Dodd S. Carr

Electrical and Computer Engineering Faculty Research & Creative Works

Battery energy storage systems, comprising lead-acid batteries, power conversion systems, and control systems, are in commercial operation around the world. They are used by three main groups: power generating utilities; power distributing utilities; and major power consumers (such as electric furnace foundries). The principal advantages of battery energy storage systems to generating utilities include load leveling; frequency control; spinning reserve; modular construction; convenient siting; no emissions; and investment deferral for new generation and transmission equipment. Power distributing utilities and major power consumers can avoid costly demand changes by discharging their batteries at peak periods and then recharging with lower cost …

Lightning Arrester Failure And Ferroresonance On A Distribution System, L. J. Bohmann, J. Mcdaniel, Eldon Keith Stanek

Electrical and Computer Engineering Faculty Research & Creative Works

Since 1987 the Upper Peninsula Power Company (UPPCO) has been experiencing a large number of lightning arrester failures on a portion of their distribution system in southern Marquette County, Michigan. It was in the area of the Navy's Extremely Low Frequency (ELF) antenna where the distribution system had been recently reconfigured so that the transformers were connected line-to-line in order to eliminate interference from the antenna. A study was done which determined that the system was susceptible to ferro resonance during single line faults under lightly loaded conditions and that the overvoltage's experienced could be causing the lightning arrester failures. …

Permeation Of Several Gases Through Elastomers, With Emphasis On The Deuterium/Hydrogen Pair, M. (Mark) W. Fitch, W. J. Koros, R. L. Nolen, J. R. Carnes

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Diffusion and Permeation Coefficients for He, H2, D2, O2, and N2 in a Variety of Elastomers Were Measured by Simple Manometric Methods. the Elastomers Studied Were Butyl Rubber; Hypalon® 40 and 45; Viton® E60 and GF; Hydrin® 100 and Filled Hydrin® 100; Kraton® G, FG, and KG VTEOS; EPDM; Epoxidized Natural Rubber; and Neoprene. Consistent with Earlier Studies, Elastomers with Higher Glass Transition Temperatures Exhibited Lower Diffusion Coefficients. the Ratio of Diffusion Coefficients of the Hydrogen Isotope Pair Differed from the Purely Molecular‐weight‐based Prediction. Deuterium's Slightly Smaller Size Relative to Hydrogen is Consistent with Observed Deviations from the Molecular‐weight‐based …

Robust Control Of Flexible Structures Using Multiple Shape Memory Alloy Actuators, R. Lashlee, R. Butler, Vittal S. Rao, F. Kern

Electrical and Computer Engineering Faculty Research & Creative Works

The design and implementation of control strategies for large, flexible smart structures presents challenging problems. To demonstrate the capabilities of shape-memory-alloy actuators, we have designed and fabricated a three-mass test article with multiple shape-memory-alloy (NiTiNOL) actuators. The force and moment actuators were implemented on the structure to examine the effects of control structure interaction and to increase actuation force. These SMA actuators exhibit nonlinear effects due to dead band and saturation. The first step in the modeling process was the experimental determination of the transfer function matrix derived from frequency response data. A minimal state space representation was determined based …

Emc Applications Of Emap-2: A 3d Finite Element Modeling Code, Todd H. Hubing, M. Ali

Electrical and Computer Engineering Faculty Research & Creative Works

EMAP-2, a 3-D finite element modeling code that can be used to model simple printed circuit board configurations, is discussed. It is a true full-wave field solver designed to be used for education or research. EMAP-2 is written in the C programming language. The code, its capabilities, and its limitations are described. Two examples illustrate how the code can be applied to problems of particular interest to EMC (electromagnetic compatibility) engineers.

Detection Of Skin Tumor Boundaries In Color Images, Fikret Erçal, M. Moganti, William V. Stoecker, Randy Hays Moss

Computer Science Faculty Research & Creative Works

A simple and yet effective method for finding the borders of tumors is presented as an initial step towards the diagnosis of skin tumors from their color images. The method makes use of an adaptive color metric from the red, green, and blue planes that contains information for discriminating the tumor from the background. Using this suitable coordinate transformation, the image is segmented. The tumor portion is then extracted from the segmented image and borders are drawn. Experimental results that verify the effectiveness of this approach are given

Surface Emitting Semiconductor Lasers And Arrays, Gary A. Evans, Jacob M. Hammer

Electrical Engineering Research

No abstract provided.

Construction And Performance Of Highway Soil Subgrades Modified With Atmospheric Fluidized Bed Combustion Residue And Multicone Kiln Dust, David Q. Hunsucker, Tommy C. Hopkins, Tony L. Beckham, R. Clark Graves

Kentucky Transportation Center Research Report

In an effort to increase the utilization of by-product materials in highway construction projects, the Kentucky Transportation Cabinet authorized the experimental use of reside from an atmospheric fluidized bed combustion (AFBC) process and multicone kiln dust (MKD), a by-product resulting from the production of lime, as subgrade soil modifiers. This report presents information relative to preconstruction and post-construction laboratory evaluations, construction procedures, construction monitoring activities, and performance evaluations of a highway subgrade solid modified using AFBC spent lime, MKD, Type IP cement, and hydrated lime. An untreated section served as a control section for the project located on Kentucky Route …

Paschen's Law For A Hollow Cathode Discharge, H. Eichhorn, K. H. Schoenbach, T. Tessnow

Bioelectrics Publications

An expression for the breakdown voltage of a one‐dimensional hollow cathode discharge has been derived. The breakdown condition which corresponds to Paschen’s law contains, in addition to the first Townsend coefficient, and the secondary electron emission coefficient two parameters which characterize the reflecting action of the electric field and the lifetime of the electrons in the discharge. The breakdown voltage for a hollow cathode discharge in helium was calculated and compared to that of a glow discharge operating under similar conditions.

An Analytical Investigation Of Aashto Load Equivalencies, Herbert F. Southgate

Kentucky Transportation Center Research Report

An objective of this study was to develop procedures and/or refined relationships between Kentucky ESALs and AASHTO ESALs. Kentucky load equivalency relationships are the result of mechanistic analyses based on elastic theory. AASHTO load equivalency relationships were developed from recorded empirical data collected at the AASHO Road Test. Comparison of Kentucky and AASHTO ESALs necessarily in depth analyses of AASHTO load equivalency equations C-19, D-19, and their developmental equations given in the 1972 AASHTO Interm Guide. These equations evolved from the basic format used in analyzing AASHO Road Test data.

In this investigation, the repetitions reported in Appendix A of …

Weapon System Integration For The Afit Virtual Cockpit, William E. Gerhard Jr.

Theses and Dissertations

The Air Force Institute of Technology is continuing research in the Virtual Cockpit. The Virtual Cockpit makes use of high performance graphics workstations, Virtual Environment technology, and Distributed Interactive Simulation network protocols to create a flight simulator based on the capabilities of the McDonnell Douglas F-15E Strike Eagle. The work presented in this thesis focuses on the design and implementation issues for integrating a weapons delivery capability. Weapons simulated include: RADAR and IR guided air- to-air missiles, gravity and precision guided bombs, and a 20mm cannon. Virtual Environment displays used include: color NTSC and monochrome high resolution helmet mounted displays …

The Use Of A Factory Simulation To Evaluate A Flexible Control Structure For Integrated Manufacturing, Ling Ling Pan

Engineering Management & Systems Engineering Theses & Dissertations

Once a control structure for an integrated manufacturing system is decided upon, manufacturing activities are limited by that structure. A flexible control structure is presented as an approach for accommodating a variety of manufacturing activities, without being limited to a single control structure. A flexible control structure is one that allows multiple types of control structure in the manufacturing process. For example, both hierarchical and non-hierarchical structures may be used in a flexible structure. The properties of a flexible control structure are discussed from the point of view of graph theory.

Control structures for automated manufacturing are difficult to evaluate …

Cultural Transposition: Exploring Meanings Of And Strategies For Cross-Cultural Transfer Of Organizational Practices, Yongming Tang

Engineering Management & Systems Engineering Theses & Dissertations

The research objective is to study the phenomenon of transferring organizational practices which are conceptualized in one culture to another different culture. The purpose of the study is (1) to understand how cultural values and beliefs are manifested in behavior; (2) to explore how the Western organizational practices are interpreted and assimilated into an organization in an Eastern culture; and (3) to explore strategies for the fit between local cultural orientations and imported organizational practices. A qualitative, interpretive, and reflexive research methodology was developed to conduct this study.

The study was conducted in two phases. The first phase was designed …

Diffusion Of Total Quality Management: An Organizational Self-Production Perspective, Baizhong Zhao

Engineering Management & Systems Engineering Theses & Dissertations

American industries are in the process of a quality revolution. Most companies are busy implementing Total Quality Management (TQM) programs. However, the experience of both Japanese and American companies indicates that successful TQM implementation depends on an understanding of implementation processes, which itself relies on an understanding of organizational self-organizing, for it is through this process that TQM gets diffused and becomes a core component of an organization's culture. Self-organizing is a so-called process-oriented approach, based on theory from cybernetics (Ashby, 1962; Steier & Smith, 1985; von Foerster, 1960), dissipative structure theory (Prigogine & Stengers, 1984), and chaos theory (Gleick, …

Multidimensional Approach To Implementation Of Continuous Process Improvement Utilizing Small Run Analysis In A Shipyard Environment, Paul Ray Hollandsworth

Engineering Management & Systems Engineering Theses & Dissertations

Nationally, both public and private shipyards are experiencing a high rework rate (over 40%) in the fabrication of plug connectors used for electronic systems onboard Navy vessels. The shipyard's survival depends on acquiring the elements necessary to maintain a major industry in a position of continuous improvement that produces a better product than their competitors, at less cost, in a safe manner, and on schedule.

This research addresses the complex problem of how to introduce quality control methodologies within a job shop environment that assists in identifying variables that influence the rework rate of plug fabrication process over a four …