Engineering Commons^™

Investigation Of Economic Design Procedure For A Rigid Frame, Richard S. Groner

Masters Theses

"This work presents an analysis of various arrangements of component parts of a rigid frame. From this analysis a procedure is indicated for a logical choice of member sizes for a first trial selection of a frame for given loading conditions. The first trial solution yields a frame which is in the range of an economical design"--Abstract, page 2.

Deflections Of Two-Way Slabs, Gerald C. Godzwon

Masters Theses

"A reinforced concrete member is by no means a truly elastic member, hence all ordinary deflection calculations relating to it, whichever method, are approximate. By the use of model study actual reinforced concrete slab models, of different end conditions, were built and tested for deflections under uniform loadings. Theoretical and actual deflection of reinforced concrete slabs are compared. The results of these tests indicate that the theoretical deflection equations may be 60 to 80 percent in error when applied to reinforced concrete slabs"--Abstract, page 2.

The Lattice Constants Of Chromium And Vanadium Containing Dissolved Gases, Paluri Bhimeswara Rao

Masters Theses

"The physical properties of chromium and vanadium are so important that a study of their lattice constants and their coefficients of thermal expansion, requires special consideration.

A number of research workers, over a period of about forty years, have done considerable work in determining the above constants. Some of the previous investigators found an anomaly in the thermal expansion, electrical resistivity and other physical properties of chromium. They observed that at about 37°C, chromium showed a discontinuity in the above physical properties. However it is not known what causes the discontinuity in the expansivity curve of chromium. The discontinuity may …

A Method For The Prediction Of Detection Ranges For Pulsed Doppler Radar, Phillip Orlan Brown

Masters Theses

"Modern radar systems must provide greater detection ranges both against high and low altitude targets because of the significant advances in weapon speed and range. Extended range indicates that the power transmitted by the radar must be increased. It follows, that ground return becomes a problem even at high altitudes.

There are at present three basic types of radars which are (1) pulsed, (2) continuous wave, and (3) pulsed doppler radar. The conventional pulsed radar now closely approaches the theoretical optimum performance; however, it does not have the inherent ability to distinguish between ground return and moving targets. The continuous …

A Dissolution Rate Study In Hydrofluoric Acid Of Titanium And The Alpha Solid Solutions Of Oxygen In Titanium, John L. Ratliff

Masters Theses

"The dissolution mechanism of titanium in hydrofluoric acid was studied by collecting the hydrogen evolved during the dissolution reaction. A concentration range of 0.05 N to 0.50 N and a temperature range of 15°C to 45°C were employed for the determination. Values of the reaction order and energy of activation were determined for both pure titanium and the alpha solid solutions of oxygen in titanium and found to be the same within experimental limits. This indicated that the reaction giving rise to hydrogen evolution on the surfaces of both pure titanium and the TiO_x alloys was the same. The …

Some Physical, Chemical, And Thermohydrodynamic Parameters Of Explosive Ammonium Nitrate-Fuel Oil Mixtures, Joseph J. Yancik

Doctoral Dissertations

"The explosive properties of ammonium nitrate-fuel blasting agents were investigated by measuring their detonation velocity and sensitivity. Detonation velocity was measured by a pin oscillograph method with a modified pin technique. Five types of tests were used to evaluate the explosive sensitivity of AN-fuel mixtures under varied environmental conditions. These tests measured the confined and unconfined critical diameter, minimum primer for a three inch diameter iron pipe confined charge, for an unconfined charge at the critical diameter, and minimum primacord primer under special conditions.

Properties of ammonium nitrate-fuel blasting agents were evaluated by considering the effects which each component of …

A Follow-Up Study Of Former Senior High School Industrial Arts Students At Belle Plaine, Iowa, Donald E. Wallis

Dissertations and Theses @ UNI

The primary purpose of this study was to determine, through the experiences and present status of the graduates and drop-outs who enrolled for industrial arts at the Belle Plaine High School, how effectively the industrial arts program had met their vocational as well as their general needs after leaving high school.

Further purposes of the study were 1) to evaluate the present industrial arts program in the school; and (2) to recommend changes which might enable the industrial arts department to meet the needs of youth more effectively.

The Effectiveness Of The Mass-Production Technique In Achieving Selected Objectives For Industrial Arts, Michael William Horton

Dissertations and Theses @ UNI

The purpose of this study was to answer the following questions related to the mass-production technique of teaching industrial arts:

1. Will two comparable groups of student show a significiant difference in achievement with respect to selected industrial-arts objectives when one group is taught by the traditional method and the other is taugh, in part, by the mass-production technique?

2. Will a mass-production project conducted for a period of six to eight weeks aid in the students' understanding of the problems, processes, and methods fo product development and production in industry?

3. Will students who work exclusively on individual projects …

Factors That Influenced Homesteading And Land Abandonment In San Juan County, Utah, Melvin J. Frost

Theses and Dissertations

Homesteading in San Juan County, Utah is for the most part, located on Sage Plain at elevations between 6,000 to 7,200 feet. Sage Plain is an undulating surface deeply dissected with canyons. The soil is relatively shallow and the predominant vegetation is pinyon, juniper, sage brush and blue-stem grass.

The 52 year mean precipitation is 15.47 inches. Since the beginning of weather records there has been a noticeable decrease in the annual precipitation. There is generally sufficient moisture to mature winter wheat. Pinto beans are also grown in the more favorable locations.

Principle factors that have influenced homesteading and land …

A Theoretical And Experimental Analysis Of A Hall Generator, David L. Endsley

Electrical and Computer Engineering ETDs

This is a study of the behavior of a "Hall Effect" device by theoretical and experimental methods to determine if its operation may be predicated for various magnetic fields, output resistances, operating temperatures, input resistances, input control currents, and device construction.

This information should prove useful in the design of a circuit where the use of a "Hall Effect" device is contemplated.

An Experimental Method For Three-Dimensional Dynamic Stress Analysis, Larry E. Williams

Mechanical Engineering ETDs

It is the purpose of this thesis to present an evaluation of a method of experimental dynamic stress analysis utilizing electrical resistance strain gauges located internally. If it can be shown that the proposed experimental procedure is valid, then the transient stress phenomena could be continuously recorded from an internal, integral strain gauge placed at any desired location and in any orientation in a suitable model.

Exploratory Study High Purity Colbalt Using An Anion Exchange Resin, Charles Edward Hoffman

Theses

This investigation accounts for the exploratory phase of a program to develop a commercial or semi-commercial process for producing high purity cobalt; in effect, a separation of cobalt and nickel.

An extensive review of all published literature, patents, etc. from 1900 to 1958 of all known commercial, semi-commercial and analytical methods of separating cobalt and nickel was completed. Qualitative evaluation of these methods to determine the possibility of one being practically extended and/or developed to produce high purity cobalt yielded one potential commercial method. Developed for analytical purposes by Moore and Kraus (1), use is made of the fact that …

The Electrolytic Reduction Of Ethyl Paranitrobenzoate, Matthew Felix Lipworth

Theses

The factors governing the electrolytic reduction of ethyl para-nitrobenzoate have been investigated, and conditions established for the optimum yield of the end-product benzocaine. The formation of intermediate compounds was studied, and a mechanism for the reduction favoring the mono-molecular route has been suggested. The material costs of the electrolytic reduction have been shown to compare favorably with the material costs of a chemical reduction, such as the Bechamp process.

Salt Effects On Distribution Of Fatty Acids, John Henry Sivori

Theses

Data are reported on the extraction of formic, acetic, propionic, and butyric acids from water with methyl isobutyl ketone. Prime consideration is given to the effect of an added inorganic salt, calcium chloride, and also to the effect of the presence of a common ion on the distribution of the acids in the solvent-water system. Extraction into the solvent phase is increased by the addition of calcium chloride, but only slightly affected by the addition of a common ion.

Fugacity And Activity Coefficients For Methane-Carbon Dioxide System, Robert J. Capik

Theses

The Redlich and Kwong equation of state has been used along with the method derived by H. C. Van Ness (18) to calculate the fugacity and activity coefficients of the components of the methane-carbon dioxide system. Calculations have been carried out for the pure gases and four mixture compositions at 160°F. and 280°F. with pressures up to 600 atmospheres.

The method of Van Ness was used because it offered an accurate and simple way of calculating the fugacity and activity coefficients. This is accomplished by a combination of analytical and graphical procedures in which the graphical error is minimized by …

Reductive Dehalogenation Of Alkyl Iodides, Vsevolod Gruenman

Theses

The rates of reductive dehalogenation reactions of alkyl iodides with zinc and acetic acid relative to the rate of deiodination of methyl iodide were investigated.

The order of ease of replacement of the iodine for the various substituents on the carbon atom of methyl iodide was found to be;

Vapor Liquid Equilibria Of Diacetone Alcohol In Various Solvents, John A. Mulligan

Theses

This paper presents the initial study of vapor-liquid equilibria data for the systems (a) diacetone alcohol-methanol (b) diacetone alcohol-ethanol and (c) diacetone alcohol-benzene at 100mm and 200mm and confirms the data reported by Hack and Van Winkle (6) on the system (d) diacetone alcohol-water at the same pressures. Margules and Redlich and Kister constants have been determined from the data, and are presented for use in future studies.

A comparison has been made between Redlich and Kister constants determined from laboratory data, and Redlich and Kister constants predicted from the physical properties of the components. Redlich and Kister constants predicted …

Batch Heating And Cooling Nomographs, Stephen Zakanycz

Theses

Heat transfer problems associated with batch heating and cooling processes are relatively complex since conditions of unsteady state prevail. Complex mathematical equations are available which relate the time required to heat or cool a quantity of material in a specific piece of equipment or to design heat exchangers to transfer the desired amount of heat in a specified time. By the use of alignment charts, these equations are solved graphically with speed and accuracy. Nomographs are presented for equations dealing with heating and cooling agitated batches, counterflow and nonisothermal medium for two cases: coil-in-tank or jacketed vessel and external heat …

Alkylation With Some Alkyl Borate By The Friedel-Crafts Methods, Richard Ernest Huber

Theses

Normal butyl, allyl, methylbutyne and 2-chloroethyl borates were synthesized in yields above 90.0% from their corresponding alcohols and boric acid. Using some of the above alkyl borates, and others commercially available, as alkylating agents, benzene was alkylated by the Friedel-Crafts method, using aluminum chloride as the catalyst. Yields were dependent on catalyst concentration. The alkyl benzenes were identified by means of: 1) physical constants, 2) infrared spectra, 3) melting points of derivatives, and 4) chemical analysis. Starting with normal alkyl borates, the formation of isomeric and dialkylated products was established through the analytical data.

Diffusion Coefficient From Hydrogen Ion Exchange Studies, Michael Maxwell Kahn, Norman A. Martin

Theses

The study of monovalent and bivalent ion diffusion coefficients was undertaken to determine the practicability of using the Reichen berg equation to calculate a film thickness from a single diffusion coefficient and through the use of this film thickness to predict the diffusion coefficient of any monovalent or bivalent ion.

Experimentation employed the use of a mixing vessel with a two bladed propellor into which a solution of known ion concentration was kept at a constant temperature and mixing speed. Dowex 50 x -8 hydrogen ion type resin was added to the solution and by means of a pH meter …

Collection Of Germanium From Acid Etch Waste By Ion Exchange, Robert Welsh Meyler

Theses

This report is an investigation of the use of ion exchange resins to recover germanium from acid etch wastes encountered in transistor manufacture.

Most of the experiments were performed with acid etch waste of unknown germanium content. The object was to determine if the ion exchange technique were applicable, and to select the most practical operating procedure.

When a satisfactory procedure had been established, later experimental runs were made with an acid etch solution of known germanium concentration to determine the yields of recovered germanium.

Yields of 60 per cent to 75 per cent recovery of germanium from the etch …

Enthalpies And Partial Molal Enthalpies For Methane-Carbon Dioxide System, Isaac Pass

Theses

Enthalpies and partial molal enthalpies have been calculated by a combination of analytical and graphical procedures for the methane carbon dioxide binary system at 160°F, and at pressures from 200 to 9000 psia.

Mixtures containing .0852, .19912, .3583 and .6685 weight fraction of methane in carbon dioxide, as well as the pure components were used. The method for calculation of the enthalpies was outlined by Van Ness (1) and involves the application of residuals to the Redlich-Kwong equation of state (2).

The results of this paper illustrate the value of the method as an accurate and reasonably convenient tool. Excellent …

A Study Of The Application Of Digital Computers For Controlling Vehicle Traffic At A Signalized Intersection, John V. Wait

Civil Engineering ETDs

This study outlines a method whereby a small, specialized "on-line" digital computer could be used to control urban vehicle traffic at a signalized intersection. In the basic system proposed, the computer uses as input data a "history" of the instantaneous vehicle flow, in terms of number of cars arriving and arrival time. The data are stored for a period of 240 seconds in a magnetic drum memory. Once each 1/2 second, the computer examines the arrival pattern of cars and compares the delay being imposed on the waiting cars versus the delay which would be imposed on the cars on …

A Reactor Transfer Function Analyzer, Earl O. Swickard Jr

Electrical and Computer Engineering ETDs

This thesis describes the design of a device for determining the transfer function of a nuclear reactor. A number of different methods have been successfully employed for this purpose but were, in some cases, tedious or required the use of delicately balanced components. The equipment described computes values which are simply related to the values of the transfer function and is operable over a frequency range of about 1000:1. The time required to obtain data for one frequency point is two minutes or less. No precise adjustment is necessary during operation.

Identification Of Inclusions In Armco Ingot Iron By The Use Of Polarized Light, Carl A. Plate

Bachelors Theses and Reports, 1928 - 1970

It is the author's hope that by systematically investigating the inclusions in ingot iron and comparing their specific properties with the properties of substances known to exist as inclusions, a rapid and accurate method may be found to identify them using a polarizing microscope. Where possible photomicrographs will be used to illustrate the results obtained so that the reader may obtain a better picture of the effects produced by polarized light.

An Investigation Of The Fundamental Factors Affecting The Green Ball Characteristics In Pellet Formation, Thomas J. Wright

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation is to determine the relative effects on the quality and characteristics of the pellets. Once the major factors effecting agglomerating materials are understood, formerly poor and nonagglomerating materials may be affected so that they will produce good quality agglomerates. Should the factors prove difficult to vary or impossible at least they may be identified and understood, thus serving as a guide for further attack or judgment in overall process design.

The Volumetric Analysis Of Nitrocompounds Using Chromous Chloride, Charles Caslin Jamison

Theses

Chromous chloride has been shown to be more efficient than titanous chloride in the reduction of refractory nitro and nitramine groups in both aromatic and aliphatic compounds.

It was found that concentrated hydrochloric acid increases the efficiency of chromous chloride to a point where it would reduce the most difficult to deduce nitro-campounds.

The compounds studied were p-Nitromethylaniline, 2,4-Dinitrotoluene, 2,4-Dinitroaniline, 2,4,6-Trinitrotoluene, Nitroguanidine, I,9-Di4cetoxy-2,4,6,8-penta-methylenetetranitramine, Sym-Cyclotrimethylenetrinitrimine, and Sym-Cyclotetramethylenetetranitramine.

Heat Transfer By Natural Convection In Horizontal Fluid Layers : A Statistical Correlation Of Experimental Data, John Lawrence O'Toole

Theses

The rate of heat transfer due to natural convection in confined, horizontal, fluid layers can be expressed by equations involving the dimensionless parameters Nusselt No., Rayleigh No., and Prandtl No., where Rayleigh No. equals the product of Grashof and Prandtl Nos.

Statistical correlation by stepwise multiple regression of experimental data obtained from four different investigators, on both gases and liquids, yields three separate equations corresponding to three distinct regimes of convection. The total range spanned by the data is from the onset of convection to Rayleigh = 109.

The equations are Regime Ra Range Equation Std. Error of Estimate Initial …

The Plastic Design Of Steel Cofferdam, Robert O. Disque

Theses

The fundamental purpose of this thesis is to employ the plastic theory in the design of a hypothetical steel sheet pile cofferdarm. Prior to undertaking this work, the author had had no previous experience with the plastic theory. Therefore, a portion of this thesis is devoted to the development of the fundamentals necessary for the actual design computations.

The theory of plastic analysis has been used as far back as the 1920's in Hungary for the structural design of apartment buildings. It is, however, only in recent years that the theory has been utilized to a significant degree in this …

Transient Response Of A Mass Mounted On A Nonlinear, Strain-Rate Sensitive Element, Wiley T. Holmes

Electrical and Computer Engineering ETDs

The object of the present transient movement study was not that of investigation of response of a nonlinear system alone, but was projected to include the effect of a strain-rate sensitive, nonlinear restoring element.