Engineering Commons^™

The Effect Of A Knurled Heat Transfer Surface Upon Pool Nucleate Boiling Of Normal Pentane, Jerry James Carr

Doctoral Dissertations

"The effect of knurling a nucleate boiling heat transfer surface was studied. The knurling utilized produced regular, four-sided, adjacent pyramids with an apex angle of 90 degrees. Four knurling densities were used ranging from 416 to 2591 pyramids per square inch. The transfer surface was gold-plated copper and the heaters used were electrically heated, ten-inch long, horizontal cylinders of one-inch diameter. The liquid boiled was normal pentane at its saturation temperature and a pressure of 760 millimeters mercury.

For some of the knurled surfaces the temperature difference required to produce a given heat flux was found to be less than …

Preparation Of Metallic Oxide Aerosols By Vaporization And Degradation Of Organic Compounds, Tom B. Larsen

Chemical and Biological Engineering ETDs

Simple, dependable methods for the generation of aerosols are necessary to many forms of research. Specifically inhal­ation research has a requirement for sub-micron sized insoluble particles.

Two different methods for the production of oxide aerosols from vaporizable compounds were tried. The first method, a mod­ification of the Rapaport-Weinstock generator (R3), consisted of nebulization of a solution into a droplet mist. Next the drop­lets were vaporized, and condensation nuclei formed from the nonvaporizable impurities in the solution. The vapor was allowed to condense on the nuclei in a relatively large chamber, then the resulting liquid droplet aerosol was dried and converted …

An Experimental Study On Heat Transfer Coefficient For Carbon Laden Gas, Jacob Chi-Kwong Huang

Chemical and Biological Engineering ETDs

Abstract

A complete carbon black pilot plant was employed in this study. Carbon laden gas was produced in a fur­nace and introduced into the outer pipe of a heat ex­changer. Air, at the same time, was introduced into

the inner pipe of the heat exchanger cocurrently with the carbon laden gas. Thus, heat, with temperature dif­ference as driving force, would transfer from the car­bon laden gas to the air stream. The temperatures along the two streams were measured by iron-constantan ther­mal couples and recorded by a multi-reading temperature

recorder. Air supply and fuel (C3H8) supply were intro­duced into the furnace …

A Comprehensive Investigation Of The Behavior Of Saturated Sands Subjected To Cyclic Triaxial Loadings., James Francis Kanipe

Civil Engineering ETDs

Considerable interest in earthquake engineering has developed during the past decade. Due to the potential hazards involved in foundation failures of nuclear power plants, and because there is an increase in the demand for earth dams throughout the world together with a decrease in desirable sites, it has become imperative that reliable techniques be developed to predict the response of soils to earthquake induced forces. As an integral part of such an endeavor, this research program was directed toward the identification of the various factors which significantly influence the development of pore pressure in saturated sands subjected to cyclic stress …

Basic Instrumentation Of A Three-Zone Convection Coater Dryer For Calculation Of Heat And Mass Balances, Byron H. Mckinstry

Masters Theses

No abstract provided.

Development Of An Apparatus To Obtain Temperature Profiles Of Molten Flowing Polymers, Ismail Kemal Saltuk

Theses

The object of this investigation is to develop and test an apparatus to predict temperature profiles of polymer melts in laminar flow in a heat exchanger, with non-isothermal wall conditions.

A commercial polyethylene melt is pumped at various flow rates through a smooth 0.957 in. I.D. pipe. The entrance temperature of polymer is maintained uniform.

Radially distributed six thermocouples (0.062 in. 0.D.) are placed at 2.5 ft. intervals from the entrance of heat exchanger. Immersion of these probes parallel to the flow direction, reduced the errors due to the conduction of heat from the tube wall to the thermocouple stems. …

Continuous Interfacial Polycondensation Of Nylon 6-10, Sumer Raj Hundia

Theses

Nylon 6-10 has been prepared by continuous interfacial polycondensation hexamethylenedlamine and sebacoyl chloride in a stirred system. The effect of monomer concentration and stirring on the intrinsic viscosity of the polyamide 6-10 solution in m-cresol was measured.

As stirring (RPM) and monomer increased the intrinsic and the polymer yield through a maximum. Diffusion coefficients (D_AB) for hexamethylenedlamine were for hexamethylenedlamine were and were used for the calculations of j_D factors and K/DAB ratios. A relationship and j_D factors was established by a correlation curve.

Three Dimensional Elastic Wave Propagation In Bodies Of Revolution, Robert S. Pritchard

Mechanical Engineering ETDs

This dissertation describes solution of a class of problems of three dimensional (non-symmetrical) elastic wave propagation in bodies of revolution. The method of analysis is expansion into circumferential modes followed by solution of an approximate numerical scheme using a digital computer. The material constituting the body has been assumed homogeneous, isotropic, linearly elastic and only one mate­rial may appear in the body. A load may be applied either by a pressure blast or by a target body acting over some portion of the boundary. The loading functions may vary around the circumference. Three dimensional wave motion is analyzed by expanding …

The Design Of A Laser Doppler Velocimeter, Marlo R. Anderson

Theses and Dissertations

A relatively new method of measuring local velocity in a fluid stream has been devised which eliminates some of the inherent problems of the traditional methods. This method senses the Doppler shift of light scattered from a laser beam incident on particles suspended in the fluid. The Doppler shift is proportional to the particles (or fluid) velocity. This new technique has several distinct advantages over the more traditional methods of velocity measurement.

A Study Of The Effects Of Some Parameters Of The Galloping Of Electric Transmission Lines, Leland J. Coleman

Theses and Dissertations

Freezing rainstorms coupled with moderate winds have often been observed to cause telephone lines and power transmission cables to begin bouncing up and down. This slow frequency high amplitude oscillation, or galloping as it is sometimes called, can build up to large amplitudes before the oscillation either damps out or persists at some constant amplitude. It has been reported by Edwards and Livingston [1] that the amplitude of galloping on transmission lines has been as large as forty feet. Galloping oscillations occur at relatively low frequencies; from .1 to 1 Hz. [1] near the natural frequency of the suspended cable.

A Dynamic Model Of A Small Manufacturing Company, Abraham John

Theses and Dissertations

A manufacturing company typically has the objective of maximizing the long-term value of its common stock while satisfying its customers. To achieve this, the company might increase the quantity and improve the quality of production. Since the company is operating in a dynamic environment, its policies should be dynamic also, to achieve its objective.

A Data Reduction Technique For Drag-Coefficient Data For Spheres, Stephen Thomas Merrell

Theses and Dissertations

The object of this investigation was to obtain a reliable technique for finding the drag coefficient for a sphere falling at a non-constant velocity through air. And then to apply this technique to the data collected by R. G. Lunnon in 1925^(4)*.

An Optimization Technique Applied To The Determination Of Modal Damping Coefficients, Craig C. Smith

Theses and Dissertations

Although analytical techniques are generally available for the simulation of dynamic systems, often these techniques require a great deal of computer time and storage. This difficulty was vividly pointed out by a previous thesis undertaken in this Department by R. L. Webster (1). Mr. Webster undertook the determination of orthotropic material properties using dynamic response test data from plates. A major difficulty which was encountered was the enormous amount of computer time required for the simulation. This thesis is an investigation of a method which when fully developed, may provide the ability to simulate such systems much more efficiently.

Transport Calculations In Particle-Loaded Media, Gary J. Scrivner

Nuclear Engineering ETDs

Particle-loaded materials are sometimes used for radiation shielding. In many cases shielding calculations, performed with the assumption of a homogeneous medium having the appropriate ratio of particle-to-matrix material, are grossly inadequate. The exact distribution of particles within such materials is probabilistic in nature, and, therefore quantities, such as the transmitted flux, become random variables. To reasonably evaluate the effectiveness of this type shielding, one must obtain the expected values and corresponding standard deviations of those quantities of interest.

In this dissertation, two models of a particle-loaded shield are investigated. The first is an artificial material postulated to consist of constant-thickness …

Complex Disjunctive Decompositions Of Incompletely Specified Boolean Functions., Stuart Lee Hight

Electrical and Computer Engineering ETDs

This dissertation extends the theory of Ashenhurst and Curtis on complex disjunctive decompositions of Boolean functions. The extension takes this theory into the realm of incompletely specifies Boolean functions, that is, those with don-t-care conditions (phi’s). First, the theory is extended to a simple decomposition through a compatibility relation on incompletely specified Boolean vectors whose elements are 0’s, 1’s and phi’s. This relations is applied to the columns of the decomposition charts used by Curtis and Ashenhurst. To accomplish complex disjunctive decompositions, a new Boolean variable, called a constrained don’t-care is introduced as a component of a new Boolean vector …

Prediction Of Hugoniots For Soil Using The Theory Of Mixtures., Robert O. Davis

Civil Engineering ETDs

An analytic derivation for the constitutive relation governing the response of soil to high intensity shock loading is presented. The derivation is based on the contemporary theory of mixtures. Soil is envisioned as a three component mixture (solids, water, and air) and jump equations for each of the components are derived. Mass, momentum, and energy transfer between the various components is allowed and it is assumed that the solid and water components obey a Mie-Gruneisen equation of state. A mixture Hugoniot is developed and compared with published experimental results.

Wetting Of Carbon Filaments By Organic Liquids, Linden Tewes Halstead

Chemical and Biological Engineering ETDs

The object of this was to find the factors controlling the rate of wetting of carbon filaments by organic liquids. To carry out this study, the factors affecting the wetting of surfaces, such as the surface tension of liquids, and the contact angle formed at the liquid-vapor-solid boundary of a three phase system were discussed. At the same time, the anomalies with respect to contact angle, such as that relating to advancing and receding contact angles to dynamic angles was considered. As complimentary information, the methods used to obtain carbon and graphite filaments from cellulose and molten pyrolysis products were …

The Silicon Micro-Hall Device: Design, Fabrication, And Applications, Roy Arthur Colclaser

Electrical and Computer Engineering ETDs

A family of silicon devices, the micro-Hall devices, are described. These include the diffused, diffused-epitaxial, isolation-diffused-epitaxial, mesa-epitaxial, and silicon-on­sapphire isolation-diffused structures. The design and fab­rication of these devices are presented in complete detail.

The theory of the Hall effect and its applications to the theory of fast neutron displacement damage to silicon is presented. A quantitative model of radiation damage in the form of spherical intrinsic voids representing the damage clusters is described.

Three applications of the isolation-diffused-epitaxial silicon micro-Hall device are discussed in the following paragraphs.

The first of these, the evaluation of epitaxial silicon, has three features which …

A Numerical Solution To The Problem Of Rotation Near The Ground, David D. Chen

Mechanical & Aerospace Engineering Theses & Dissertations

No abstract.

Grain Size Reconnaissance Of The Virginia-North Carolina Inner Shelf Analysis By Settling Technique, Robert Bailey Sanford Jr.

OES Theses and Dissertations

The 2-fold purpose of this study is to calibrate a Rapid Sediment Analyzer and to use it to aid in the determination of the genesis of sediment on the inner continental shelf between Cape Henry and Cape Hatteras. Rapid Sediment Analyzer calibration was conducted by comparison of sieving and settling results of similar sands.

The study area was divided into sediment provinces by both a qualitative procedure (grain size and topography) and a quantitatively procedure (factor-vector analysis). Qualitative provinces are beach and surf, upper shore face, lower shore face, sea floor, and terminal shoals. The berm fines from each terminal …

A Study Of Elasto-Viscous Material Under Moving Rigid Wheel, Sou-Nan Wang

Civil & Environmental Engineering Theses & Dissertations

This thesis is considered as the solution of interaction between aircraft wheel and soil under landing of airplane. After treating soil as elasto-viscous material, we get a set of non-linear differential equations, such as momentum equations, in viscous region.

A numerical method, Marker-and·-Cell (MAC) method, was used to solve these equations. All data and curves are obtained by using CDC 6600 computer.

An Experimental Study Of Lateral Soil Pressures And Moments On Flexible Sheet Piles, James H. Donahue

Civil & Environmental Engineering Theses & Dissertations

In order to study the effect compaction has on lateral earth pressures exerted on and bending moments in steel sheet pile bulkheads, an experimental study was undertaken which employed the placement of a non-cohesive soil at two specific densities against three model piles of varying thicknesses. The soil was placed both in a loose and a dense state and the bending strains and deflections of the sheet piles were measured at various stages of backfill. Surface loadings were then placed after completion of the backfilling to observe the effects these loads had on the bending moments. The results of the …

Theoretical And Experimental Evaluation Of Cardiac State Utilizing Indicator Dilution Methods For Nonuniform Ventricular Mixing, Stanley Myron Welland

Dissertations

This research is directed toward the development and application of a new approach to the evaluation of cardiac work to diagnose cardiac state. A procedure has been developed for calculating the work performed on the fluid by the left ventricle during the heartbeat. The procedure involves the continuous direct measurement of ventricular fluid mixture temperature during and following the controlled injection, through a catheter, of a known volume of cold saline into the left ventricle. The measured mixture temperatures are used to calculate continuous ventricular volumes during the systolic and diastolic functions of the heartbeat. Plotting measured ventricular pressure versus …

A Kinetic Study Of The Anionic Polymerization Of Neopentylethylene Oxide, Albert Edward Meisinger

Dissertations

Kinetic data for the anionic polymerization of bulk neopentylethylene oxide were determined. The initiator used for this study was potassium t-butoxide. Polymerization runs were made at temperatures of 39.9, 60.0 and 80.3°C using monomer to initiator ratios of 50/1 and 20/1.

The polymerization reaction was found to follow pseudo first order kinetics up to about 60% polymerization and second order after this. The energy of activation for the propagation reaction was found to be 17.4 ± 1.2 K cal/mole and 18.5 ± 1.5 K cal/mole, respectively, for the pseudo first order and second order portions of the polymerization. The value …

On The Classification Of The Solution Space Of Linear Anisotropic Elasticity, Richard Clement Carman

Dissertations

A method is developed within the framework of Synge's function-space interpretation of problems in linear elasticity which allows the consideration of solutions to problems for anisotropic media in terms of the solutions of a corresponding isotropic problem and corresponding simpler anisotropic problems. The isotropic solution and simpler anisotropic solutions establish points in each of the statically and kinematically admissible spaces for the anisotropic problem. The established points are used to define sets of vectors in the statically and kinematically admissible spaces. The linear independence of these vectors can then be determined by a pair of criteria developed in this work. …

Continuous Esterification Of Lactic Acid With N-Butyl Alcohol, Robert Dix

Dissertations

A model is proposed for the reactions occurring when an aqueous 30% lactic acid solution is contacted with a primary alcohol, normal butanol. Kinetic and equilibrium data for the esterification reactions of monomeric lactic acid and dimeric lactic acid were determined in a series of experiments using an ideal overflow back-mix reactor. The variables studied were reaction temperature and catalyst concentration.

It was determined that the significant reactions occurring within this system are the esterification of monomeric lactic acid with n-butanol and the esterification of dimeric lactic acid with n-butanol. Other reactions that may be postulated to occur within the …

A Study Of The Dynamics Of Gas Adsorption In An Air Fluidized Bed, William Charles Zalewski

Dissertations

The dynamics of gas adsorption was studied in an air fluidized bed containing activated alumina particles. The adsorption studies made with a fixed bed and in the transition region between minimum fluidization velocity and 2.0 times minimum fluidization velocity, compliment work done at higher velocities. With adsorption, particle motion controlled the overall dynamics of the fluidized bed. A different approach in applying the two phase fluidization model was necessary to satisfactorily describe unsteady state adsorption in fluidized beds. Experimental and theoretical results were compared in frequency response plots to obtain a rigorous comparison. Good agreement was obtained for flow rates …

The Absorption Of Hydrogen Chloride From Dilute Air Mixtures, Edgar L. Demarest

Theses

A study was made of the absorption of hydrogen chloride from air mixtures containing from 1 to 40 mgm. HCl/liter (1000 to 40000 mgm./m.³), using a.4" diameter tower packed with 2" Intalox saddles, irrigated with water or with sodium hydroxide solutions of 0.3% to 3.8% concen?tration. Gas flow rates of 177 to 752 lbs./(hr.)(ft.²) were investigated at three liquid rates: 2960 ; 4260, and 5700 lbs./(hr/)(ft.²). All data were collected below the flooding point.

Correlations of the height of a transfer unit with the superficial gas velocity were prepared for water and for sodium …

Aiir Pollution Emissions From Turbine Powered Aircraft, Raymond Arthur Filippini

Theses

The major pollutants that are emitted by jet aircraft include: particulate matter (soot), carbon monoxide, aldehydes, hydrocarbons, and nitrogen oxides. The first of the pollutants, particulate matter (smoke), constitutes not only a visual nuisance but is also a potential health problem. The rest, which are not visible, are irritants and in high enough concentrations can be toxic.

Since pollutants emitted by jet aircraft are of the same type as those given off by a car, a direct comparison is possible. In one landing take off cycle (LTO), a four engine jet aircraft emits the same amount of particulate matter as …

A Digital Computer Simulation Of A Batch Or Semi-Batch Reactor, Robert Edward Viczorek

Theses

A digital computer simulation of a batch or semi-batch reaction was developed. The system consisted of a jacketed, agitated vessel equipped with a temperature controller modulating a control valve in the stream to the jacket. The reaction was liquid phase, and the jacket medium was liquid.

The program was written in a general form so as to be applicable to any liquid phase reaction with minimum modification.

A numerical technique was employed using initial values of the process variables in the first cycle of calculations for a time interval, and then using average values for further iterations. The simulation proceeded …