Engineering Commons^™

Simultaneous Extraction And Sorption Under Supercritical Conditions, Ş. Uğur Akman

USF Tampa Graduate Theses and Dissertations

Supercritical Exsorption (SCEXS), simultaneous supercritical extraction and sorption (adsorption and/or desorption), is a novel process which may have potential for applications in chemical, biochemical and environmental engineering. The system of interest consists of a fixed-bed packed with an adsorbent (e.g., activated carbon or catalyst) through which a so~vent stream (e.g., supercritical carbon dioxide) and a feed stream (e.g., an aqueous stream with low concentration of solute such as phenol) flow countercurrently.

In this work, the theoretical foundations of SCEXS have been established through distributed-parameter modeling which enables phenomenal description of several probable three-phase mass transfer dynamics taking place in the …

1-Nitronaphthalene Causes Ultrastructural Changes Primarily In Nonciliated Bronchiolar Epithelium Followed By Ciliated Epithelium In The Rat, John-Michael Sauer

Masters Theses

This study describes morphological changes in the lung at several time intervals following a single injection of 1-Nitronaphthalene (100 mg/kg intraperitoneal) in male Sprague-Dawley rats using transmission and scanning electron microscopy. Dilation of the smooth endoplasmic reticulum and mitochondrial distension in the nonciliated bronchiolar (Clara) cells was apparent as early as 1 hour after injection, while adjacent ciliated cell showed minimal changes. At 6 hours, when respiratory distress was apparent in the animals, Clara and ciliated cells exhibited chromatin clumping, loss of mitochondrial cristae and cytoplasmic vacuolization. Also at 6 hours, the interstitial area around the terminal bronchioles was infiltrated …

Experimental Evaluation Of Design Variables For Two-Dimensional Confined Jet Thrust Vector Control Nozzles, Timothy M. Hawkes

Theses and Dissertations

An experimental study of the axial and vectoring performance of two - dimensional (2-D) confined jet thrust vector control (CJTVC) nozzles was performed. The effects of adding secondary injection ports and changing exit height and secondary injection port location were studied on several 2-D CJTVC nozzles. The axial and vectoring performance results for these nozzles were measured over a range of pressure ratios. An analytical method for predicting flow separation was found to be applicable to these nozzles. Guidelines for designing 2-D CJTVC nozzles, that can be vectored using secondary injection, were established.

A Multiple Model Adaptive Estimator Using First And Second-Order Acceleration Models For Use In A Forward-Looking Infrared Tracker, Barbara J. Niblett

Theses and Dissertations

The performance of a multiple model adaptive estimator (MMAE) for an enhanced correlator/forward-looking-infrared tracker for airborne targets is analyzed in order to improve its performance. Performance evaluation is based on elemental filter selection and MMAE estimation error sizes and trends. The elemental filters are based on either first or second-order acceleration models. Improved filter selection is achieved by using acceleration models that separate the frequency content of acceleration power spectral densities into non- overlapping regions with second-order models versus the more traditional overlapping regions with first-order models. A revised tuning method is presented. The maximum a posteriori (MAP) versus the …

An Alternative Algorithm For Discrete-Time Filtering, Frederick H. Zeitz Iii

Theses and Dissertations

The discrete-time Kalman filter is a conditional mean estimator of the states of a linear stochastic process, conditioned on the previous state and current measurements. It assumes that the states and noise inputs can be represented as jointly Gaussian random variables. The influence diagram is a decision analysis tool. Under certain conditions, it can represent continuous, jointly Gaussian random variables. The conditioning order of the random variables may be changed (using Bayes' rule) so that any random variable can be conditioned on any other subset of random variables in the diagram. Under these conditions, an influence diagram can represent the …

High Frequency Scattering Code In A Distributed Processing Environment, Scott Suhr

Theses and Dissertations

Government agencies and academic institutions are very interested programming for concurrent processing to cut computer processing time. However, many of the world's problems have already been coded for conventional serial computers. This research demonstrates the feasibility of modifying existing serial codes for execution in a concurrent processing environment. A electromagnetic scattering prediction code known as NECBSC is incrementally modified to incorporated various levels of concurrent computing. The data processed by the code are completely independent, providing an avenue for data decomposition of the process. Portions of the data set are processed on each mode and the results combined for final …

Operations Research In A New Spanish Air Force Planning System, Antonio Valderrabano

Theses and Dissertations

The focus of this research effort was to determine a new Spanish Air Force Planning System. Today's highly technological weapon systems are very expensive, and resources are very scarce. So its selection has to be done very carefully. This process can allow high flexibility, be helpful facing the budgetary problems for all the Air Forces, and also can be easily integrated in a joint defense system. The path defined in this thesis is able to be adapted for different situations. It can be useful for other Services or countries, when their own peculiarities have been set up on the defined …

Tensile Behavior Of Hybrid Woven-Fabric-Composites, Hussein M Massoud

Archived Theses and Dissertations

No abstract provided.

Reactivities Of Some Aromatic Compounds At Supercritical Water Conditions, Chun-Cheng Tsao

Masters Theses

The goals of this study are the removal of nitrogen from the extraction products of coal by Supercritical Water and the development of an understanding of the reactions leading to this removal. Six model compounds with structures similar to the intermediates of the coal liquefaction processes were studied. Benzylamine generated toluene through hydrogen abstraction after the C-N bond rupture. To a lesser extent, the oxidation of the benzylic carbon took place leading to benzene formation. Both reaction pathways occurred with equal probability for benzylidenebenzylamine, producing comparable yields of benzene and toluene. Benzaldehyde generated benzene through the oxidation/decarboxylation sequence. Benzyl alcohol …

Investigation Of Adaptive Controllers For Puma Trajectory Tracking, Daniel J. Sims

Theses and Dissertations

Two robust model-based controllers and two decentralized adaptive controllers are experimentally evaluated. Algorithm evaluation is motivated by the need for controllers with good high speed tracking under varying payload conditions. The test case is a PUMA-560 robotic manipulator operating over the standard test suite. The model-based controllers are made robust by the addition of either an auxiliary input term or an adaptive feedforward compensator based on Lyapunov Theory. The model-based auxiliary input controller (MBAIC) adapts the gain matrices used in computing an additional torque to be combined with model-based feedforward and PD feedback torques. The adaptive model-based controllers adapt the …

Development Of A Personal Computer Simulation Program Of The Ln-94 Inertial Navigation System, Thomas E. Flynn

Theses and Dissertations

This thesis develops a simulation that emulates a Litton LN-94 INS. Real time simulation is achieved for a stationary navigation case and a straight-and-level flight trajectory are provided to exercise the simulation dynamics. The user interface is simple and requires little previous knowledge to operate. The communication link with the MILSTD 1553B bus provide a realistic environment in which to collect and analyze data. The simulation is processed on an 80386 IBM compatible personal computer. A 23-state INS error model is implemented and integration is performed by a fifth-order Kutta-Merson routine. The simulation is interfaced to a plotting routine and …

Mosfet Audio Amplifier, Jeff Argast

Undergraduate Honors Capstone Projects

My senior project is an audio amplifier utilizing MOSFETs as the output transistors to drive the speaker. Within this document I cover the details of designing an amplifier, and the methods used to build it.

The most important part of the project is the output stage. In this section I chose MOSFETs over BJTs. Several advantages ensued from this decision, resulting in a simple design.

Further, the transformer must be able to supply the necessary currents for the transistors. Because large musical peaks are possible, resulting in sizable power surges, I had to obtain a large transformer with adequate specifications. …

A Vision System Model, Erik J. Fretheim

Theses and Dissertations

This dissertation provides four major contributions to the field of vision research. The first contribution is a general vision system model. The model, which blends biological as well as technological methods into a coherent approach to vision, will provide a basis for implementing vision systems. The second contribution of this dissertation is to demonstrate particular implementations of portions of the model. These implementations will include methods for using Gabor wavelets in edge detection, in preprocessing images for use as feature vectors in backpropagation neural networks, and as basis functions in a recognition/reconstruction network, as well as methods for integrating color …

Mathematical Modeling Of Mass Transfer In Microvascular Wall And Interstitial Space, Daekyung Kim

Dissertations

The dynamics of macromolecular transport across the microvascular wall and into the adjoining interstitial space was studied in the hamster cheek pouch using intravital fluorescence microscopy in combination with digital image processing. Fluorescein isothiocyanate-labe led dextrans (FITC-Dx) of 70,000 and 150,000 daltons were used as tracers. In each experiment, the time-dependent extravasation of FITC-Dx from a leakage site in a blood vessel was videotaped for about 2 hours. The macromolecular transport from individual microvessels was quantified by digital video-image processing. Histograms of the light intensity distributions for selected fields at various times were obtained and then converted to the interstitial …

The Theory Of Bootstrapped Algorithms And Their Applications To Cross Polarization Interference Cancelation, Abdulkadir Dinc

Dissertations

Dual-polarized transmission has become an important method for frequency re-use, particularly in satellite and microwave radio communication. Nevertheless, cross-polarization interference, which is inherent to this method, may cause degradation in system performance.

Different canceler [sic] structures have been proposed to mitigate the effect of cross-polarization. Among these are the diagonalizer, the least mean square (LMS) canceler [sic] and the bootstrapped cancelers [sic]. Bootstrapped canceler [sic] schemes have been proposed and implemented in different applications, such as satellites, tactical communications, and quadrature amplitude madulation [sic] (QAM) dual polarized microwave radio. Nevertheless, no attempt was made in the past to quantify the …

Mathematical Modeling Of Chemical Vapor Deposition Processes And Its Application To Thin Film Technology, Norman W. Loney

Dissertations

A number of workers in the field of Chemical vapor deposition (CVD) have presented mathematical models in the literature. Some workers were able to produce analytical expressions for the interwafer concentration profile. These analytical expressions were based entirely on zero or first order chemical reaction rates. Until now, it appears that a chemical reaction rate expression that is not zero or first order directly, must be handled by a numerical scheme.

Presented herein is a mathematical model with an analytical interwafer concentration profile. This concentration profile is neither zero nor first order but shifts from zero to first order as …

Investigation Of Stagnation Flow Heat Transfer For A Heated Horizontal Round Plate, Ching-Hua Wei

Dissertations

The heat transfer characteristics in stagnation flow are investigated through three cases in this study. The first is forced convection by an array of air jets; the second is free convection of a downward-facing heated round plate; the third is free convection of an upward-facing heated round plate.

The first case is investigated by systematic experiments which examine the heat transfer characteristics mainly by five air jets impinging normally to a flat plate, with varying nozzle diameters, and Reynolds numbers, at different distances between the nozzles and the plate. The empirical formulas of heat transfer around the stagnation point and …

Kinetic Studies On Pyrolytic And Oxidative Decomposition Of Chlorocarbons In A Tubular Flow Reactor, Yang Soo Won

Dissertations

Chloroform decay and product distributions were distinctly different in the absence and presence of added O₂ and/or CH₄. Increases in O₂ concentration were observed to speed reagent loss, with a slower decay of chloroform observed for the CHCl₃/CH4/Ar pyrolysis system. In CHCl₃/CH₄/O₂, the major products were C₂Cl4, CH2CCl₂, C₂HCl₃, CO and CO₂ over a wide temperature range. Minor products included CH₂Cl₂, CH₃Cl, and C2H₃Cl. When CH₄ reactant was not present, …

Performance Analysis Of Symbol Timing Recovery Circuits Employed In Digital Communications Systems, Elisha Yegal Bar-Ness

Theses

An analytical approach is presented for the jitter performance of a timing recovery circuit consisting of a prefilter, a zero-memory nonlinear device, and a narrow band postfilter tuned to the pulse repetition frequency. Assuming first a squarer type of nonlinearity, analytical expressions for the rms jitter in the timing wave are obtained as a function of the pre and post filtering characteristics. These expressions are suitable for judging the case where the baseband signal is bandlimited. Also for some specific examples, the jitter performance of this kind of STR circuit is evaluated.

Secondly, a general type of nonlinerity is assumed, …

Development Of A Classification And Coding System For Computer-Aided Process Planning, Shilpan K. Patel

Theses

The chore of this work was to develop a Group Technology Classification Code which can represent the full gamut of simple, rotational parts. The automated coding plan is developed to alleviate the endeavor of the process planner to plan the tasks related to the manufacturing of a specific part. The 15 digits were devised from the Japanese KK-3 Classification and Coding system. The KK-3 System contains 21 digits. Our aim is to minimize the code length, and concurrently to eliminate the redundancies. As a result, a 15 digit G.T. Code is created. The proposed plan also generates the operation logic …

Multistage Interconnection Networks : Improved Routing Algorithms And Fault Tolerance, Kuo-Yu Chen

Theses

Multistage interconnection networks for use by multiprocessor systems are optimal in terms of the number of switching element, but the routing algorithms used to set up these networks are suboptimal in terms of time. The network set-up time and reliability are the major factors to affect the performance of multistage interconnection networks. This work improves routing on Benes and Clos networks as well as the fault tolerant capability. The permutation representation is examined as well as the Clos and Benes networks. A modified edge coloring algorithm is applied to the regular bipartite multigraph which represents a Clos network. The looping …

Dynamic Analysis Of The Generalized Slider Crank, Sahidur Rahman

Theses

A numerical technique is used to analyze the kinematics of the generalized slider crank mechanism and an analytical technique to derive dynamic force equations for that mechanism has been formulated. The numerical technique used for displacement analysis is based on a combination of Newton-Raphson and Davidon-Fletcher-Powell optimization algorithm using dual-number coordinate-transformation matrices. Velocity analysis is performed by using a dual number method. Finally, dynamic force analysis is accomplished on the basis of the dual-Euler equation and D'Alembert's principle. The approach is developed in such a manner that a digital computer can detect when a solution is possible and then solve …

Task Scheduling For Fms Based On Genetic Algorithm, Hung-Yuan Li

Theses

A Flexible Manufacturing System (FMS) consisting of p automated guided vehicles (AGV's), m workstations and n tasks is studied. The main problem investigated in this thesis is to find an optimal or suboptimal task scheduling for p AGV's among m workstations to complete n tasks.

An efficient approach based on genetic algorithms has been designed and implemented to solve the problem of task scheduling for a FMS. Near-optimal, or even optimal, task scheduling is accomplished by genetic algorithms. Simulation results on the algorithm are also discussed.

Petri Net Modeling And Analysis Of An Fms Cell, Paresh A. Patel

Theses

Petri nets have evolved into a powerful tool for the modeling, analysis and design of asynchronous, concurrent systems. This thesis presents the modeling and analysis of a flexible manufacturing system (FMS) cell using Petri nets. In order to improve the productivity of such systems, the building of mathematical models is a crucial step.

In this thesis, the theory and application of Petri nets are presented with emphasis on their application to the modeling and analysis of practical automated manufacturing systems. The theory of Petri nets includes their basic notation and properties. In order to illustrate how a Petri net with …

Off-Line Programming Using Igrip, Narahari K. Bhandary

Theses

AT&T's FWS-200 (Flexible Work Station) has been modeled and simulated to implement Off-Line Programming (OLP). IGRIP (Interactive Graphics Robot Instruction Program) from Deneb Robotics, Inc. has been used to simulate the FWS operation.

A GSL(Graphics Simulation Language) program has been used to simulate the chip placements during PCB assembly. The program leads the user through the motions of chip placement, and after the simulation run downloads the motion sequence to the FWS. The animation sequences of the FWS have been downloaded to the FWS on the Factory Floor using a C program, which is utilized to communicate the data to …

Performance Evaluation And Comparison Of Ordinary, Adaptive And Exhaustive Services In The Token Ring Network, Hong Wang

Theses

Ordinary service and exhaustive service are two major alternatives of scheduling policies considered in providing access to token ring networks. Results to date have shown that exhaustive service results in more delay to lightly loaded stations in asymmetric traffic while ordinary service wastes time in circulating the token after each transmission. This work presents a new token passing protocol, called adaptive service, in which the token holding time is dynamically changing; in this way, it provides a fair compromise between exhaustive and ordinary service. The simulation results show that in asymmetric traffic, adaptive service gives improvement on the local delay …

Implementation Of Automated Assembly, Kang H. Kong

Theses

Research has shown that about 60 - 80% wealth producing activities is related to manufacturing in major industrial countries.

Increased competition in industry has resulted in a greater emphasis on using automation to improve productivity and quality and also to reduce cost.

Most of the manufacturing works such as machining, painting, storage, retrieval, inspection and transportation have changed to automation successfully, except assembly. Manual assembly is predominant over automatic assembly techniques due to inherent assembly problem and the fact that the assembly machines lack the innate intelligence of human operator and lack sufficient flexibility to changeover when product designs and …

A Parallelogram Four-Frame Model In 3-D Motion And Structure Recovery Using Unified Optical Flow Field Approach, Zhichun Lin

Theses

In this paper a new concept of the unified optical flow field (UOFF) for 3 D motion analysis from a stereo image sequence is implemented which is an extension of the temporal optical flow formulations developed by Horn and Schunck. A four frame model is established and a spatial optical flow is also introduced.

In order to alleviate the problem of the strict requirement of two identical sensors in common stereo imagery a new imaging system is presented in this paper that needs only one camera, two plane mirrors and two switches to generate a phase shifted binocular sequence of …

Simulation Of Voice And Data Integration, Urmila S. Patel

Theses

A simulation model of integrated voice and data is developed. The data packets are transmitted during voice inactivity (i.e. silence duration). A statistical model of voice (talkspurt) and silence duration is generated. inter-arrival time between data packets is modeled using geometrical distribution. The data traffic statistics is simulated for a given voice activity model and various data packet arrival rates. Four important results are obtained by performing this simulation: 1. Average data packet delay versus arrival rate. 2. The optimal ratio of data packet arrival rate to average data packet delay. 3. Probability of wait time for various data packet …

Size Reduction Of Polymeric Particulates By Jet Milling, Cheng Hua

Theses

A basic theory for the size reduction operation by jet milling has been developed.

Typical samples of feedstock have been analyzed using screen analysis to determine the initial distribution of polymeric particulate sizes prior to jet milling.

A statistical theory .was developed using probabilities to represent the likelihood that specific size reductions would occur. These probabilities include the effects of various equipment.

The theory was then used to predict the distribution of polymeric particulate sizes after jet milling. The agreement between the predictions and actual results was within 5 %.

Encouraged by the successful work of the simulation of the …