Engineering Commons^™

Development Of Pole Impact Testing At Multiple Vehicle Side Locations As Applied To The Ford Taurus Structural Platform, Mark Halford Warner

Theses and Dissertations

A test method was developed whereby repeated pole impacts could be performed at multiple locations per test vehicle, allowing a comparison of energy and crush relationships. Testing was performed on vehicles moving laterally into a 12.75 inch diameter rigid pole barrier. Crush energy absorption characteristics at the different locations were analyzed, and the results compared to test data from broad moving barrier crashes and available crash tests with similar pole impacts. The research documents the crush stiffness characteristics for narrow impacts at various points on the side of the Taurus vehicle platform. Factors encountered during the research include the importance …

Polarimetric Temperature Sensor Using Core-Replaced Fiber, Benjamin L. Ipson

Theses and Dissertations

Optical fibers are increasingly being used to create sensing devices. The D-fiber has an elliptical core and exhibits birefringence. This birefringence can be used to create a polarimetric sensor. The elliptical core supports two orthogonal modes that have separate effective indices of refraction. The indices of refraction change with a change in temperature. Since the effective indices of refraction change differently for the two modes, the birefringence also changes. This change in birefringence can be seen as a change in detected power through the fiber through the use of polarizers. The fiber then becomes a temperature sensor. The sensitivity of …

The Effectiveness Of Computer-Based Tutorials In Learning Computer-Aided Design Methods For Tool Design Procedures, Andrew Moroni Hall

Theses and Dissertations

Throughout the past twenty-five years the process of designing and manufacturing a product has been revolutionized by the integration of Computer Aided Design (CAD). Although three-dimensional solid modeling, or 3-D CAD offers a better representation of the product in a virtual environment, it can be complicated and difficult to learn. Tutorials have been developed to assist manufacturing tool design student in the learning of 3-D CAD principles as they apply to tool design. This study seeks to test the effectiveness of those tutorials. A BYU tool design class was divided into two groups according to their assigned laboratory time. The …

Compliant Mechanisms To Perform Bearing And Spring Function In High Precision Applications, Jesse R. Cannon

Theses and Dissertations

An increasing number of mechanical systems are being designed on the micro and meso scales. Assembly and maintenance become increasingly difficult as the size of mechanisms decrease, and the minimum size of traditional elements such as bearings and springs is limited. The backlash of bearings also limits their usefulness in applications where high precision and repeatability are needed. At small scales and for high precision applications, alternative, non-traditional elements are needed.

The objective of this thesis is to develop reliable and scalable compliant components to replace bearings and helical springs. Components replacing springs must be able to produce specified torque/motion …

Improved Signal Integrity In Ieee 1149.1 Boundary Scan Designs, Efren De Jesus Rangel Taboada

Theses and Dissertations

This work is an analysis of solutions to problems derived from inherent timing and signal integrity issues in the use and application of the IEEE 1149.1 Standard at the board level in conjunction with its test system. Setup or hold times violations may occur in a boundary scan chain using IEEE 1149.1 compliant devices. A practical study of the TDI-TDO scan data path has been conducted to show where problems may arise in relationship to a particular board topology and test system. This work points to differences between passing and failing scan path tests for problem characterization. Serial data flow …

Thermally Developing Electro-Osmotic Convection In Circular Microchannels, Spencer L. Broderick

Theses and Dissertations

Thermally developing, electro-osmotically generated flow has been analyzed for a circular microtube under imposed constant wall temperature (CWT) and constant wall heat flux (CHF) boundary conditions. Established by a voltage potential gradient along the length of the microtube, the hydrodynamics of such a flow dictate either a slug flow velocity profile (under conditions of large tube radius-to-Debye length ratio, a/lambda_d) or a family of electro-osmotic flow (EOF) velocity profiles that depend on a/lambda_d. The imposed voltage gradient results in Joule heating in the fluid with an associated volumetric source of energy. For this scenario coupled with a slug flow velocity …

Quantifying The Effects Of Aging On The Mechanical Properties Of Medical Grade Polycarbonate And Uv Cured Adhesives, Christopher James Lewis

Theses and Dissertations

Advances in engineering polymer technology have created a generation of high strength-to-weight materials for medical applications, with virtually no adverse interactions with body fluids. Polycarbonate is a widely used engineering polymer, and is often used in connection with ultra-violet light (UV) cured adhesives. Because of the chemical complexity of polymers, little is known about their actual aging characteristics. By characterizing the effects of aging, storage environment, and sterilization on medical grade polycarbonate/adhesive system properties, more accurate failure predictions can be made. In this thesis, efforts to better understand the effects of accelerated aging on a medical grade polycarbonate and UV …

A Cad-Centric Approach To Cfd Analysis With Discrete Features, Matthew Lee King

Theses and Dissertations

During the conceptual design stage several concepts are generated, and a few are selected for detailed analyses. CAD models from conceptual design often follow the "over-the-wall" approach for downstream analyses such as FEA, CFD, heat transfer, and vibrations. A CAD-centric approach will be applied to the CAD-to-CFD process to help industry in an ongoing quest to shorten the design cycle time. The CAD-centric approach consists of using the CAD model as a source of data for downstream applications such as mesh generation, and CFD setup. The CAD model used in the CAD-centric approach contains the geometry to be analyzed and …

Decision Factors For Cooperative Multiple Warhead Uav Target Classification And Attack With Control Applications, Douglas D. Decker

Theses and Dissertations

Autonomous wide area search, classification and attack using Unmanned Combat Air Vehicles (UCAVs) is considered. The wide area search and attack scenario is modeled, capturing important problem parameters related to environment, seeker, and munitions. Probabilistic analysis is used to formulate and analytically solve for various probabilities, including the probability of mission success. Two methods are utilized. The first examines the sub-events required for various events to occur. The second utilizes a Markov chain approach. General expressions are first obtained that are applicable to any assumed a priori distributions of targets and false targets. These expressions are subsequently applied to a …

Development Of A Virtually Calibrated Projection Moire Interferometry Technique Capable Of Inaccessible Surface Measurements, Mark Lee Kimber

Theses and Dissertations

Optical-based techniques have found merit in measuring displacement and strain for decades. These techniques are commonly used in numerous applications ranging from large displacements in wind tunnel experiments to displacement measurements on the submicron scale. Projection Moiré Interferometry (PMI) is an out-of-plane displacement measurement technique, and consists of capturing reference and deformed images of a grid pattern projected on the test object. By differencing the reference and deformed images of the projected grid pattern, a fringe pattern is generated from which the displacement field can be extracted. This computation requires calibration procedures that analyze a number of fringe patterns from …

Variation Simulation Of Fixtured Assembly Processes For Compliant Structures Using Piecewise-Linear Analysis, Michael L. Stewart

Theses and Dissertations

While variation analysis methods for compliant assemblies are not new, little has been done to include the effects of multi-step, fixtured assembly processes. This thesis introduces a new method to statistically analyze compliant part assembly processes using fixtures. This method, consistent with the FASTA method developed at BYU, yields both a mean and a variant solution. The method, called Piecewise-Linear Elastic Analysis, or PLEA, is developed for predicting the residual stress, deformation and springback variation in compliant assemblies. A comprehensive, step-by-step analysis map is provided. PLEA is validated on a simple, laboratory assembly and a more complex, production assembly. Significant …

The Benefit Of Using Simulation To Improve The Implementation Of Lean Manufacturing Case Study: Quick Changeovers To Allow Level Loading Of The Assembly Line, Jack J. Mcclellan

Theses and Dissertations

In today's competitive manufacturing environment, companies are constantly looking for ways to improve. Because of this, many companies are striving to become "lean" by implementing lean manufacturing, which is a difficult process. To aid in the implementation of lean manufacturing, simulation was used to reduce the trial-and-error period of lean manufacturing and find to optimum approach to implement the lean manufacturing principle. In this research, a case study of implementing level loading of the production schedule for BullFrog International, L.C. will be examined. To make it possible to implement level loading, the thermo-former machine at the beginning of the operations …

A Review Of Setup Practices And Procedures For Creating Ieee 802.11 Wireless Community Networks, Jae M. Theobald

Theses and Dissertations

IEEE 802.11 wireless networking equipment has made it possible to bridge the last mile for new broadband internet service providers. Inexpensive wireless networking equipment and high gain antennas enable high speed internet delivery at a fraction of the cost of installing or upgrading land lines for cable or DSL services. Based on this research, a guide of general practices and procedures is proposed for designing, installing, and maintaining a reliable wireless community area network. Included tests have provided performance results for several types of wireless antennas (including wire grid parabolic dishes, Yagi and Vagi styles, and echo backfire), wireless bridges, …

Numerical Simulations In Electro-Osmotic Flow, Joseph S. Tenny

Theses and Dissertations

The developing flow field in a parallel plate microchannel, induced by wall motion, has been modeled numerically. This type of flow simulates the physical driving mechanism that exists in electro-osmotically generated flow with large channel diameter-to-Debye length ratios (Z). The physics of the flow field were compared between the moving wall model (MWM) and electro-osmotic flow (EOF) at Reynolds numbers of 1 and 1800, and Z > 2500. Also, Z-values between 50 and 500 were studied to investigate the accuracy of the MWM. Results show that for Z-values greater than 100 the MWM shows good agreement with EOF.

The dynamics of …

Establishing A Cyber Warrior Force, Scott D. Tobin

Theses and Dissertations

Cyber Warfare is widely touted to be the next generation of warfare. As America's reliance on automated systems and information technology increases, so too does the potential vulnerability to cyber attack. Nation and non-nation states are developing the capability to wage cyber warfare. Historically, the Air Force and DoD have concentrated their efforts toward defensive network operations. However, a shift in doctrine has shown both the Air Force and DoD acknowledging the potential for Information Warfare. What appears to be lacking is the trained and educated cyber warrior force that will carry out the information operations if needed. This research …

An Open Architecture For Versatile Machine And Actuator Control, Michael Scott Baxter

Theses and Dissertations

Automatic control technology increases usability, reliability and productivity in manufacturing, transportation, and climate control. There are many additional areas of modern life that could benefit through automatic control; however, current automation components are too expensive or aren't sufficiently flexible. For example, the cost of current commercial motion control components precludes their use in an average home. This thesis describes an automatic control methodology that is low cost and is flexible enough for a wide variety of control applications. Typical applications could include:

- Home lighting, security and appliances

- Commercial building heating, ventilation and air conditioning

- Industrial machine tool …

Device Discovery In Frequency Hopping Wireless Ad Hoc Networks, Brian S. Peterson

Theses and Dissertations

This research develops a method for efficient discovery of wireless devices for a frequency hopping spread spectrum, synchronous, ad hoc network comprised of clustered sub-networks. The Bluetooth wireless protocol serves as the reference protocol. The development of a discovery, or outreach, method for scatternets requires the characterization of performance metrics of Bluetooth piconets, many of which are unavailable in literature. Precise analytical models characterizing the interference caused to Bluetooth network traffic by inquiring devices, the probability mass function of packet error rates between arbitrary pairs of Bluetooth networks, and Bluetooth discovery time distribution are developed. Based on the characterized performance …

A Tightly-Coupled Ins/Gps Integration Using A Mems Imu, Jonathan M. Neu

Theses and Dissertations

Micro-Electro-Mechanical Systems (MEMS) technology holds great promise for future navigation systems because of the reduced size and cost of MEMS inertial sensors relative to conventional devices. Current MEMS devices are much less accurate than standard inertial sensors, but they can still be useful. In this thesis, data was recorded from an inexpensive MEMS inertial measurement unit and integrated with GPS measurements using a tightly-coupled Kalman filter. The overall goal of this research is to investigate the usefulness of MEMS sensors for a small, real-time, low-cost INS/GPS integration. A golf cart was used to collect dynamic data, along with a commercial …

Electrostatic Radio Frequency (Rf) Microelectromechanical Systems (Mems) Switches With Metal Alloy Electric Contacts, Ronald A. Coutu Jr.

Theses and Dissertations

RF MEMS switches are paramount in importance for improving current and enabling future USAF RF systems. Electrostatic micro-switches are ideal for RF applications because of their superior performance and low power consumption. The primary failure mechanisms for micro-switches with gold contacts are becoming stuck closed and increased contact resistance with increasing switch cycles. This dissertation reports on the design, fabrication, and testing of micro-switches with sputtered bi-metallic (i.e., gold (Au)-on-Au-(6.3at%)platinum (Pt)), binary alloy (i.e., Au-(3.7at%)palladium (Pd) and Au-(6.3at%)Pt), and ternary alloy (i.e., Au-(5at%)Pt-(0.5at%)copper (Cu)) contact metals. Performance was evaluated, in-part, using measured contact resistance and lifetime results. The micro-switches with …

Analytical Solution For Low-Thrust Minimum Time Control Of A Satellite Formation, John Sang-Pil Seo

Theses and Dissertations

Satellite formations or distributed satellite systems provide advantages not feasible with single satellites. Efficient operation of this platform requires the use of optimal control of the entire satellite formation. While the optimal control theory is well established, only a very simple dynamical system affords an analytical solution. Any practical optimal control problem solves the resulting two-point boundary value (TPBV) problem numerically. The relative satellite dynamics using Hill's coordinate system and approximations made by Clohessy and Wiltshire, combined with body-fixed thruster control, result in a linearized dynamic system. This dissertation provides the analysis for the minimum time satellite formation control by …

The Physical Understanding Of The Use Of Coatings To Mitigate Hypervelocity Gouging Considering Real Test Sled Dimensions, Andrew G. Szmerekovsky

Theses and Dissertations

A dimensional analysis with accompanying numerical investigation is conducted. A simplified model of the real test sled is created that allows test sled dimensions to be converted to a numerical model for analysis. The dimensional analysis is used as a means of directly applying the numerical results to real test sled conditions. Similarity principles are studied and tested by comparing the results from scaled numerical models. Strain rate and other time dependent parameters are not scaled, but the effect of these parameters may be quantified and studied further. The dimensional analysis also provides a comprehensive approach to the test sled …

Role Of Plasticity On Fretting Fatigue Behavior Of Ti-6al-4v, Kisu Shin

Theses and Dissertations

Fretting fatigue generally leads to the degradation of the fatigue strength of a material due to cyclic micro-slip between two contacting materials. Fretting fatigue is regarded as an important issue in designing aerospace structures. While many studies have evaluated fretting fatigue behavior under elastic deformation conditions, few studies have focused on fretting fatigue behavior under elastic-plastic deformation conditions. The primary goal of this study was to characterize the fretting fatigue crack initiation behavior in the presence of plasticity. Experimental tests were performed using pad configurations involving elastic-plastic deformations. In order to calculate stress distributions under elastic-plastic fretting fatigue conditions, FEA …

Quantifying Initial Condition And Parametric Uncertainties In A Nonlinear Aeroelastic System With An Efficient Stochastic Algorithm, Daniel R. Millman

Theses and Dissertations

There is a growing interest in understanding how uncertainties in flight conditions and structural parameters affect the character of a limit cycle oscillation (LCO) response, leading to failure of an aeroelastic system. Uncertainty quantification of a stochastic system (parametric uncertainty) with stochastic inputs (initial condition uncertainty) has traditionally been analyzed with Monte Carlo simulations (MCS). Probability density functions (PDF) of the LCO response are obtained from the MCS to estimate the probability of failure. A candidate approach to efficiently estimate the PDF of an LCO response is the stochastic projection method. The objective of this research is to extend the …

Frequency Estimation Of Linear Fm Scatterometer Pulses Received By The Seawinds Calibration Ground Station, Spencer S. Haycock

Theses and Dissertations

The SeaWinds Calibration Ground Station (CGS) is a passive ground station used to receive and sample transmissions from the SeaWinds scatterometer. During post processing, the received transmissions are characterized in order to verify proper instrument operation and to eliminate error in satellite telemetry and in data products generated from processing SeaWinds data. Sources of instrument error include uncertainties in transmitted power, pulse timing, and carrier frequency drift. Identifying these errors prevents their propagation to data products. A key aspect of this analysis involves accurately estimating the parameters of the SeaWinds transmissions. As better parameter estimates are researched and developed, the …

An Examination Into The Statistics Of The Singular Vectors For The Multi-User Mimo Wireless Channel, Scott Nathan Gunyan

Theses and Dissertations

Many capacity and near-capacity achieving methods in multiple-input-multipleoutput (MIMO) wireless channels make use of the singular value decomposition (SVD) of the channel matrix. For the multi-user case, the SVD of the channel matrix for each user may result in right and left singular vectors that are similar between users. This proposes another descriptive characterization of the multi-user MIMO channel. Closely aligned singular vectors between any two users could reduce the achievable signaling rates of signal processing communication methods as one user would be more difficult to resolve in space-time from another. An examination into how this alignment can be described …

Imaging Techniques And Hardware For Inhomogeneous Mri, David A. Thayer

Theses and Dissertations

Magnetic Resonance Imaging (MRI) has become one of the most important medical imaging modalities over the past few decades because of its flexibility and low risk, along with other useful attributes. For traditional MRI, the static magnetic field, B_0, must be highly homogeneous. Obtaining this homogeneity can be difficult. Traditional MRI also requires linear gradient fields that are directed along the static field direction. Under these conditions a Fourier transform relationship exists between sampled data and the image to be reconstructed. In the case of an inhomogeneous static field, gradient fields that are not linear, or gradients that are not …

Hybrid Stochastic Models For Remaining Lifetime Prognosis, Steven M. Cox

Theses and Dissertations

The United States Air Force is developing its next generation aircraft and is seeking to reduce the risk of catastrophic failures, maintenance activities, and the logistics footprint while improving its sortie generation rate through a process called autonomic logistics. Vital to the successful implementation of this process is remaining lifetime prognosis of critical aircraft components. Complicating this problem is the absence of failure time information; however, sensors located on the aircraft are providing degradation measures. This research has provided a method to address at least a portion of this problem by uniting analytical lifetime distribution models with environment and/or degradation …

Conformal Refinement Of All-Hexahedral Finite Element Meshes, Nathan Harris

Theses and Dissertations

Mesh adaptation techniques are used to modify complex finite element meshes to reduce analysis time and improve accuracy. Modification of all-hexahedral meshes has proven difficult to the unique connectivity constraints they exhibit. This thesis presents an automated tool for local, conformal refinement of all-hexahedral meshes based on the insertion of multi-directional twist planes into the spatial twist continuum. The contributions of this thesis are (1) the ability to conformally refine all entities of an all-hexahedral element mesh, (2) the simplification of template insertion to multi-directional refinement. The refinement algorithm is divided into single hex sheet operations, where individual refinement steps …

Microwave Remote Sensing Of The Greenland Ice Sheet: Models And Applications, Ivan S. Ashcraft

Theses and Dissertations

Spaceborne microwave sensors are powerful tools for monitoring the impacts of global climate change on the Greenland ice sheet. This dissertation focuses on refining methods for applying microwave data in Greenland studies by using new simple theoretical and empirical models to investigate (1) azimuth anisotropies in the data, (2) the microwave signature of the snow surface, (3) detection of snow melt, and (4) classification of snow melt. The results are applicable for identifying geophysical properties of the snow surface and monitoring changes on the ice sheet in relation to melt duration/extent, accumulation, and wind patterns. Azimuth dependence of the normalized …

A New Method For Melt Detection On Antarctic Ice-Shelves And Scatterometer Calibration Verification, Lukas Brad Kunz

Theses and Dissertations

Ku-band dual-polarization radar backscatter measurements from the SeaWinds on QuikScat scatterometer and microwave radiometer measurements from the Special Sensor Microwave/Imager (SSM/I) are used to determine periods of surface melt and freeze in the Antarctic ice-shelves. The normalized radar backscatter (sigma-0) and backscatter polarization ratio (PR) are used in the maximum likelihood estimation of the ice-state. This method is used to infer the daily ice-surface conditions for 25 selected study points located on the Ronne, Ross, Larsen, Fimbul, Amery, and Shackleton Ice-shelves. The temporal and spatial variations of the radar response are also observed for various neighborhood sizes surrounding each given …