Engineering Commons^™

An Analysis Of The Geneva Mechanism As A Timing Device, Hubert W. Meyer

Theses

A mathematical analysis of the Geneva mechanism was conducted to determine the potential of this device as a tinting mechanism, and the feasibility of replacing the widely used pallet and starwheel escapement with a Geneva mechanism.

The primary objective of the study was to determine if the Geneva mechanism will attain a terminal velocity, and if so, how much time is required to reach this velocity.

To accomplish this objective, the differential equation of motion for the system was derived using Lagrangian dynatos. The equation was programmed and solved on a digital computer.

The study indicated that the Geneva mechanism …

Aboveground Fuel Oil Storage Tanks, Lawrence George Palmer

Theses

A review of the American Petroleum Institute Standard 650 and Appendixes points out the advantages of using high strength steel and the variable point design method (Appendix K) to obtain reasonably uniform shell stresses. Design limitations imposed by notch toughness and residual stresses are pointed out.

Design considerations for the installation of an internal floating roof in a standard cone roof tank are discussed. Methods of calculating evaporation losses and an economic justification for a floating roof are included. Budget estimate figures have been compiled as a function of tank capacity for tanks, site preparation and tank ringwall or piled …

Sidestream Tower Fractionation : A Short-Cut Calculation Method, Richard David Prickett

Theses

A short-cut procedure has been developed for making calculations on a complex fractionation tower. A Simplification of the Thiele-Geddes plate-to-plate procedure provided the basis for the short-cut procedure. The application discussed in this paper is for a tower with a liquid sidestream drawoff in the rectifying section.

The tower was broken at the feed point and sidestream drawoff locations into three calculation sections. The fractionation in each tower section can then be represented by a rigorous series solution expressed in terms of absorption or stripping factors. These rigorous equations can then be simplified by the use of average absorption or …

Separation Of Glucose - Fructose - Water Systems Via Thermal Parametric Pumping, Zikri Mostafa Ahmed

Theses

Series of experiments were carried out to determine the effect of different factors on adsorption from aqueous solutions of sugar using fuller's earth ( LW 16-30 Mesh ) as an adsorbent. The equilibrium data were fitted to the Langmuir's equation., and an explanation for the deviation of some of these data has been given.

Systems of glucose-fructose and water mixtures were subjected to semi-continuous and continuous parametric pumping operations using activated carbon (400 Filterasorb) as an adsorbent. The results obtained confirm the equilibrium theory of the parametric pump and essentially fulfill the requirements established by Chen and Hill (6) to …

Diffusion Studies With Novel Plastics, Marion Toohey Conway

Theses

The rates of diffusion through two fluorinated groups and two non-fluorinated groups of laboratory prepared membranes were compared with each other and with commercially available cellulose membranes. The membranes.were evaluated, in particular, for possible use with the artificial kidney. Diffusion experiments were conducted with sodium chloride, urea and uric acid. Experimental results were compared to diffusion coefficients calculated in the literature for cellulose membranes. The results show that the rates of diffusion of all of the solutes tested for the laboratory prepared membranes are comparable to that of the cellulose membranes. The fluorinated group had a slightly higher diffusion coefficient …

Minimum Reflux In Fractionating Columns : A New And Improved Short-Cut Method, Elizabeth Garcia

Theses

A short-cut method is presented for calculating the minimum, reflux rate for multicomponent systems. This new method is best suited for use on the computer and gives a very accurate estimate of this important factor in the design of fractionating columns. It does so without going to the tedious and time-consuming calculations of the rigorous methods.

The calculation approach is based on a simplification of the Thiele and Geddes method for fractionating columns under minimum reflux conditions.

The program is written in Fortran IV language and was used on an IBM 370 computer. Input specifications include the split of the …

Kinetic Modeling Study Of Catalytic Hydrogenation Of Codimer, William Mounce

Theses

A kinetic modeling study was made on a gas phase catalytic reaction. The data used was that on the hydrogenation of codimer, collected by Tschernitz, et al, The objective was to determine if non-linear least squares regression offers an advantage over linear least squares regression in discriminating between Langmuir. Hinshelwood kinetic equations.

For the experimental data in question, it was found that neither linear nor non-linear regression could distinguish between the two plausible mechanisms. With the particular mechanistic equations and range of data used in this study, the more laborious non-linear analysis offered no advantage over linear regression in discriminating …

A Study Into The Feasibility Of Constructing A Pedestrian Mall In Newark Downtown, Stephen Wesley Warren

Theses

Newark's central business district has been suffering steady economic decline for at least a decade. In an attempt to halt this trend, and perhaps even reverse it, a feasibility study has been conducted toward the goal of implementing a pedestrian mall in the area.

This study was accomplished by conducting both field examinations of Halsey Street, the area under consideration, and investigating data from other existing United States pedestrian malls.

The results of this study show that it is feasible to construct a permanent pedestrian mall on Halsey Street and that the benefits of doing so far outweigh the costs …

Simulation Of A Single Feed Fractional Distillation Column Using The Thiele-Geddes Procedure, M. S. Abolahrari

Theses

This thesis constitutes a simulation model of a single feed frational distillation column consisting of a single phase distillate, liquid or vapor product, an equilibrium stage reboiler, and a cascade consisting of theoretical equilibrium stages. The model limitations in addition to the single feed and the single phase distillate are 20 identifiable components, and 100 theoretical equilibrium stages. The thermodynamic data required are vapor-liquid equilibrium data and vapor-liquid enthalpy data, both assumed to be correlatable as functions of temperature. Compositional dependence of the thermodynamic data is ignored, but minor pressure variations throughout the cascade can be incorporated into the vapor-liquid …

The Chemistry Of Azides, Edward D. Nelson

Theses

A review of the decomposition of alkyl and aryl azides by thermolysis and photolysis has been accomplished. Organic azides are a very distinct species that undergo its own unique reactions. Azides decompose to form an electron deficient nitrogen having a sextet of elcctrons. This is called a Nitrene. Nitrenes can exist in the singlet or triplet state. The triplet behaves like a diradical. General and specific reactions of nitrenes have been shown with detailed mechanisms accounting for the products. The main modes of nitrene stabilization are rearrangement, hydrogen abstraction and insertion. Insertion is characteristic of singlet species and abstraction characteristic …

The Fate Of Hazardous Polluting Substances In An Aqueous Environment, Robert Paul Casani

Theses

The fate of Hazardous Polluting. Substances (HPS) in an aqueous environment has been investigated using ultraviolet light. Chlorobenzene, o-cresol and nitrobenzene were used as model HPS for this study. The kinetics were followed and good first order plots were obtained for all compounds. The temperature of the reaction was shown to effect the rate. Solid insoluble and soluble non-volatile products were formed in the photolytic reaction of the three model systems.

The Aging Of Sbr Vulcanizates, Arthur Robert Leckart

Theses

A literature survey was conducted on SBR aging, Being vulnerable to attack by the forces of nature (such as ozone, oxygen, heat and light), SBR vulcanizates requires the addition of chemicals to retard aging. Phenylamines were found to be the best type of antiaging additives, The effectiveness of other antiaging additives were examined. Although the mechanisms of aging are not perfectly understood; sane theories and aging reactions are discussed.

Computer Simulation Of A Linde "Double Column", John A. Bazan

Theses

The purpose of this thesis is to develop a Fortran Computer Program to simulate the operation of a Linde "Double Column" for the separation of air into oxygen and nitrogen. The model outputs the number of contact stages required, the reflux ratio, the heat loads (condenser and reboiler, and the five profiles of temperature, pressure, vapor flow rate, liquid flow rate, and light component composition. From this data, the proposed design can be evaluated, and the effect of varying operating conditions explored.

A Solid State Kinetic Study Of Potassium Permanganate In Alkali Halide Disks, Joseph Paul Cusumano

Theses

The stoichiometry and the kinetics of the reactions of KMnO₄ in KCl and KIO₄ in KCl were studied. The kinetics of the reactions were studied at three different temperatures to obtain the thermodynamic parameters. In addition, these reactions were studied in KBr and RbI matrices. The data was obtained using infrared spectrophotometer measurements.

The reactions all appeared to be first order with respect to the permanganate ion. The stoichiometric studies indicate that the Mn₄^- is converted to Mn⁺⁺ and the Mn⁺⁺ ion apparently catalyzes the reduction of KI₄. The results indicate the …

Analysis Of Decomposition Gases And Leach Water From Controlled Sanitary Landfill, Robert Gargano

Theses

A sanitary landfill was simulated by placing "refuse" between two layers of soil in 6" by 24" cylinders. Canine nutriment was used to simulate the refuse. Once the refuse began to decompose, the decomposition gases were collected in a gas cell and analyzed in an Infrared Spectrophotometer. When gas samples were not taken, the decomposition gases were vented through a water trap (to prevent air from backing up into the system) into the atmosphere. Distilled water was added and withdrawn at two week intervals to leach out the pollutants.

From the Infrared analysis, the decomposition gases were determined to be …

Separations Via Semicontinuous Parametric Pumping, Edward H. Reiss

Theses

A semicontinuous parametric pump with batch operation during one half-cycle and continuous operation in the other half-cycle was experimentally investigated in the model system, toluene-n-heptane on silica gel adsorbent. Comparison was made with analytical results obtained by the equilibrium theory. It was shown that when the penetration distance for the cold cycle was less than or equal to that of the hot cycle and the height of the column, the rate of production of pure solvent in the semicontinuous pump may become quite large relative to that in the continuous pump.

Predictions Of Catalyst Utilization With Continuous Replacement In Multistage Continuous Reactors From Batch Reactor Data, Norman M. Feinberg

Theses

This thesis presents a new equation for predicting catalyst utilization with continuous replacement in multistage continuous reactors from batch reactor data.

An equation is derived from experimental data for a. no-replacement system which predicts catalyst activity as a function of time. The assumption of constant inventory, constant replacement rate and perfect mixing permit the calculation of catalyst age distribution. By combining age distribution with a measure of catalyst productivity, as determined from activity as a function of time, an equation for catalyst utilization was derived. The case used to prepare this equation was where the activity decline curve appears as …

Computerized Computation Of Counter-Current Extraction Problems For Ternary Liquid Systems, Albert Warren Patterson

Theses

A Fortran computer program has been developed that will calculate the number of theoretical equilibrium stages required for a countercurrent liquid-liquid extraction design problem. It also furnishes a complete stagewise material balance. Further utility can be found by using it for optimization studies. The program can be utilized for three-component systems that form one pair of partially miscible liquids, the most frequently occuring situation. The program was written for the General Electric Mark I Time-Sharing System.

The program has a practical advantage in that isothermal liquid equilibria data are used directly for calculation purposes. No use is made of theoretically …

Manpower And Productivity In The Construction Industry, John A. Purciello

Theses

The relationship between manpower and productivity is an important factor in the area of increasing construction costs. Manpower supply is affected by worker mobility, influx of minority workers, work accidents, and training and apprenticeship programs.

A survey was conducted in the state of New Jersey to determine if a manpower shortage existed. The survey was conducted by submitting questionnaires to contractors, unions, owners, and architect-engineers.

The results of the survey indicated that a manpower shortage does exist, and that the shortage has influ enced construction costs, Furthermore, as a result of the increasing costs, indications of a decline in new …

Effectiveness Of Training Programs For Graduate Engineers, V.C. Rajashekar

Theses

This thesis represents an investigation of effectiveness as a result of engineering training. The basic elements of effectiveness and its learning process are explained and said that the effectiveness could be learnt and improved.

The term training, is basically the process of education and training. But training cannot be performed as an individual, but is performed as a group. Therefore training a group with having so many individuals needs careful consideration in designing a training program.

In order to get the broadest possible picture of current thinking and current activity in the area of company training programs for graduate engineers, …

The Effect Of Ultrasonic Vibration On Mass Transfer In A Packed Column, Joseph Walter Stanecki

Theses

The object of this research was to investigate the possibility of using externally supplied ultrasonic vibration to surface of a packed distillation column operating at total reflux to improve the separation. The apparatus used for this experimentation consisted of a 2 inch ID Pyrex column having three pairs of ultrasonic transducers epoxied equidistance along the external surface of the column. Each pair of transducers was driven separately by a 50 watt amplifier! power supply and a sine/square wave generator.

There were three types of binary mixtures covered during experimentation: minimum boiling azeotropes, maximum boiling azeotropes and full range mixtures. In …

The Creep And Stress Relaxation Behavior Of Silver Bearing Copper Wire, Alfred Fox

Theses

Creep and stress-relaxation experiments were performed on silverless and silver bearing copper in the temperature range 73F to 250F. The creep experiments were conducted at constant load and temperature, the stress-relaxation tests at constant total strain and temperature for a total time period of 1000 hours. The effect of silver addition of up to 0.2 percent w/o (60oz per ton) on the creep and stress-relaxation behavior of spectrographically pure copper (99.999+ Cu) as well as on that of tough pitch and oxygen free coppers of lesser purity was studied. Spectrographically pure copper was found to be much more susceptible to …

The Reaction Of P-Nitrophenyl Acetate With Lysine Hydrochloride And Poly-1-Lysine Hydrobromide, Emmanuel Plange Matteer

Theses

The reactions of p-nitrophenylacetate with L-lysine hydrochloride and poly-L-lysine hydrobromide as a function of pH were investigated.

The results indicate that both compounds react with the substrate in the pH range 7.0-10.0 with an apparent optimum pH in the region near 9.65.

Poly-L-lysine reacts more rapidly over the entire pH range investigated than does L-lysine.

A Study Of The Optimization Of Ethylene Production In A Tubular Reactor, Richard W. J. Robertson

Theses

The pyrolysis of ethane is a complex reaction involving six individual reactions in a reactant mixture of thirteen components. It is further complicated by the deposition of carbon along the reactor walls. The carbon buildup eventually necessitates reactor shutdown, During the intermediate stages the reactor experiences a gradual increase in inlet pressure which affects the reaction conditions, Optimum temperature profiles exist because the yield goes up with increasing temperature, but, consequently, the reactor must be shut down and cleaned out with increasing frequency. The combined effect causes the yearly production of ethylene to go through an optimum.

To find this …

A Study Of The Effect Of A Dielectric Field On The Solvolysis Rate Of Tert-Butyl Bromide In A Recycle Reactor, Rolf L. Ball

Theses

Previous experiments at Newark College of Engineering have shown that a dielectric field can effect the rate of a chemical reaction. A theory was developed in this thesis to postulate how a dielectric field can increase the rate of a first order reaction whose rate determining step is an ionization. An experimental procedure was developed to measure the reaction rate constant of a tertiary alkyl halide with a solvent to test this theory. The solvolysis of tortbutyl bromide in aqueous ethanol (80%), aqueous dioxane (75%) and aqueous acetone (75%) solvent systems were the reactions selected for study. A total of …

The Development Of Langmuir's Adsorption Isotherms For Glucose And Fructose And The Separation Via Continuous Parametric Pumping, Jafir Abbas Jaferi

Theses

The adsorption equilibria and adsorption rates of fructose and of glucose on aqueous suspensions of fullers earth were determined at various temperatures. The Langmuir adsorption equations were fitted to the equilibrium data and the Langmuir constants were determined so that isotherms could be developed for any pair of parametric pumping operating temperatures.

This glucose+fructose+water system was then subjected to continuous thermal parametric pumping for the separation of glucose and fructose. The operating conditions required for the separation were determined from the experimental adsorption rates and equilibrium isotherms. Samples taken from the continuous top and bottom streams were analyzed by polarimetry …

Equilibrium Calculations Via The Benedict-Webb-Rubin Equation Of State, Steven L. Sincoff

Theses

The performance of various vapor-liquid equilibrium calculations requires phase equilibrium data. One of the most versatile sources of this data is an equation of state, re-lating the pressure, temperature, and phase compositions it a single expression. The equation under study herewith is the eight constant Benedict-Webb-Rubin Equation of State.

This paper provides a computer program which evaluates the following types of phase equilibria: bubble-points, dew-points, and two phase flash calculations. Also included in this paper is the theoretical backround of the Benedict-Webb-Rubin Equation of State, calculational techniques, and the data used in the program.

Studies Of Rare Earth Compounds, Rostam Mondegarian

Theses

The work reported herein has consisted of miscellaneous studies of rare earth compounds.

1. The Pr—As system was studied with a view to obtaining a ferromagnetic composition.
2. Attempts were made to prepare ternary compounds by solid state reaction of PrAs, GdAs or YbAs with MnAs, CrAs or FeAs, and PrP, GdP, or YbP with MnP, CrP or FeP.
3. Attempts were made to prepare quaternary compounds by solid state reaction of YbAs, YbP and GdAs with CdI2 in various molar ratios. In many cases new compouns appeared to be formed but because of complexity of the X—ray patterns it was not possible …

Flow Behavior Of Molten Polymer Blends, Kryspin Pawel Maciejewski

Theses

An experimental study of molten polymer blends was made using the Instron Capillary Rheometer. The materials investigated were two phase blends of non-crystalline polymers (poIymethylmethacrystate-low Mw-polyvinylacetate, polyvinylacetate-polystyrene, polymethylmethacrylate-low Mw-polystyrene, polymethylmethacrylate-high Mw-polystyrene), crystalline polymers (polyethylene-polypropylene) and combinations of non-crystalline-crystalline polymers (polyethylene-polystyrene). Two methods of sample preparation were used, blending of a polymer pair in a molten state by the use of Brabender blender, and a simple manual blending of pellets in desired proportion. The Brabender blended polymer pairs show lower viscosities, this is interpreted molecularly as a result of a reduction of the amount of chain entanglement on shearing of the …

Continuous Interfacial Polycondensation Of Nylon 6-6, Chandrakant A. Patel

Theses

Nylon 6-6 has been prepared by continuous interfacial polycondensation from hexamethylene diamine and adipyl chloride in a stirred system. The effect of monomer concentration and stirring on the intrinsic viscosity of polyamide 6-6 solution in formic acid (90%) was determined.

As stirring rate and monomer ratio increased, the intrinsic viscosity and polymer yield went through a maximum. Diffusion coefficient (D_AB) for hexamethylene diamine was calculated and from that J_D and mass transfer coefficient /D_AB were calculated. A relation between Reynolds number and J_D factor was established by correlation curve.