Engineering Commons^™

Dielectric Properties Of Atactic And Isotactic Polystyrene, Thaddeus F. Kroplinski

Theses

The purpose of this investigation was to determine the dielectric constant and dissipation factor of atactic and isotactic polystyrene at 25°C and at frequencies of 0.1, 1.0, 10, and 100 kilocycles per second. In addition, the effects of molecular weight and crystallinity on the dielectric properties of polystyrene mos also studied.

Polystyrene slabs of uniform thickness mere prepared by molding the polymer under heat and pressure. The isotactic polystyrene slabs Imre annealed at 175°g for various lengths of time to achieve varying degrees of crystallinity.

The molded polystyrene slabs were fitted with circular aluminum foil electrodes to form a three …

A Simple Method For Liquid Enthalpy Departure Calculations, Ching-Lin Chien

Theses

The reduced equation of state for gases and liquids developed by Benson and Golding in 1951 is modified and used to calculate liquid enthalpy departures for saturated pure substances and mixtures. The temperature-independent coefficients in the modified equation are determined from critical properties and experimental liquid enthalpies at the boiling point and at the critical point. The results of the proposed method are compared with those predicted with the modified Redlich-Kwong equation of state by Joffe and Zudkevitch.

Agitation Of Dilatant Fluids, Vijay Jang Datta

Theses

No abstract provided.

Prediction Of The Physical Properties Of Pure Gases And Liquids, James L. Filson

Theses

A computer programmed system for the estimation of physical properties of pure compounds from minimum data input on compound type and structure was developed for both gas and liquid phase conditions.

The properties of the gas phase which can be obtained include:

• gas volume
• compressibility
• normal boiling point
• volume at the normal boiling point
• critical temperature, pressure, volume compressibility
• vapor pressure
• Riedel factor
• acentric factor
• ideal heat capacity
• heat capacity at constant pressure
• heat capacity at constant volume
• dipole moment
• intermolecular distance
• hard sphere volume
• viscosity at low pressure
• viscosity at elevated pressure
• thermal conductivity at low pressure
• thermal conductivity …

A Simulation Model Capable Of Performing The Calculations Involved In Defining A Crude Preheat Train, Robert G. Parker

Theses

A simulation model has been developed for a system of ex changers to preheat the feed to a crude distillation unit. In conjunction, a Fortran program for the performance of the model calculations by digital computer was written. Two types of preheat system were simulated, a single train system and a split (or parallel) train system. A number of features were included in the program for flexibility and versatility. A particular effort was made to have the model represent as economical a preheat system as possible.

The model program was used to obtain computer-calculated results for both single-train and split-train …

Incineration Of Solid/Liquid Human Waste, Theodore Joseph Wayne

Theses

This thesis encompasses the design criteria required to produce an effective incineration system for the disposal of solid/liquid human waste. Coupled with the overall design parameters is an investigation of the chemical decomposition of the waste during the incineration process, odor treatment and control, and the physiological effects on the human body due to the inhalation of the toxic gases given off during the combustion of human waste.

The variables involved in the combustion process are studied and equations presented that relate the combustion variables of flame temperature, residence time and air requirements. These equations are tested based upon published …

A Nomograph For The Rapid Solution Of The Arrhenius Equation, Joseph John Lamont

Theses

There are presently no calculational aids for the rapid computation of the Arrhenius parameters of the chemical reaction rate equations.

Two nomographs for solving the Arrhenius equation for the relative reaction rate constants at different temperatures, and for computing activation energies and frequency factors are presented. Several graphs and tables of the relative reaction rate constant as a function of activation energy and temperature are also presented.

The nomographs, graphs and tables can be used, singly or combined, in lieu of numerical calculation for the solution for Arrhenius parameters, or the computation of rate constants.

A computer program included in …

Computer Model For Reactor Design Of An Ethane Cracking Unit, Derek J. Lough

Theses

The purpose of this thesis is to develop a Fortran [sic] Computer Program to model the radiation section of a pyrolysis tube reactor designed for cracking 100 percent ethane feed. The model calculates the length of the tubular reactor required to obtain a specified ethane conversion or the ethane conversion for a specified reactor length. The resulting solution yields a conversion profile, a temperature profile, and the reactor residence time as a function of tube length. From this data it can be determined if the design is adequate and lies within the reactor model's constraints.

A New Technique For Steady State And Transient Analyses Of Incompressible Flow Networks, George V. Catanzaro

Theses

A new technique for the calculation of the transient or the steady-state mass flow rate and pressure distribution in incompressible flow networks is presented. Employing the matrix method of network analysis, the nodal continuity and branch momentum equations are solved simultaneously to obtain explicit relations giving the unknown nodal pressures and branch mass flow rates. In this manner, the transient or the steady-state behavior of incompressible flow networks with arbitrary configuration having nodal sources and sinks as well as branch transducers can be determined. In contrast with the conventional steady-state network analysis methods, the new technique can be extended to …

A Study Of Heat Transfer And Inlet Flow Behavior In Molten Polymer Systems, Min Ho Choi

Theses

Two separate studies have been done in the present work: one to study the entrance effects in flow in molten polymer systems and the other to investigate the heat transfer to thermally softened flowing polymer.

The equipment for the entrance effect was designed to study the isothermal flow behavior of a polymer melt in the entrance region. The main object of this investigation was to find the entrance length for the melt to relax and to separate the pressure drop into viscous and elastic effect. Due to the failure in developing a proper pressure measuring device the experiment was not …

The Reaction Of O-Propylphenyl Azide With Di-N-Propylamine, Seyed Ziaeddin Razavi

Theses

Nitration of n-propylbenzene resulted in O-nitro-n-propylbenzene. Reduction of this compound gave o-n-Propylphenyl azide was prepared by diazotization of o-n-propylaniline followed by treatment with sodium azide.

Photolysis of o-n-propylphenyl azide in di-n-propyl-amine yielded two new azepines, 2-di-n-propylamino-3n-propyl-3H azepine and 2-di-n-propylamino-7-n-propy1-7H-azepine. Their structures were assigned on the basis of their physical properties (i.e. I.R., U.V., N.M.R., N.S. and elemental analysis).

Photolysis of the azide at room temperature gave 26.9% o-n-propylaniline and 4.3% 2-di-n-propylamino-3-n-propy1-3H azepine, but when the photolysis was carried out in the presence of the triplet photosensitizer (xanthen-9-one) the yield of o-n-propylaniline was increased to 34.6% and the yield of 2-di-n-propylamino-3n-propy1-3H-azepine …

Stability Analysis Of A Continuous Stirred Tank Reactor With An Autocatalytic Reaction, David Elliot Rosenberg

Theses

The basic principles of stability analysis are set forth, including the development of a mathematical model, steady state analysis, integration of the dynamic system equations, and predictions of transient responses. The equations for the mathematical model are developed for a continuous stirred tank reactor with a cooling jacket, containing an autocatalytic reaction, in unsteady state operation. These equations are numerically integrated to obtain a good picture of reactor dynamics about the steady state. State variable methods, including the classical linearization theorems and Lyapunov's Second Method, are utilized to predict bounds of stable reactor behavior. A discussion of the shortcomings of …

Continuous Interfacial Polycondensation Of Nylon 6-10, Sumer Raj Hundia

Theses

Nylon 6-10 has been prepared by continuous interfacial polycondensation hexamethylenedlamine and sebacoyl chloride in a stirred system. The effect of monomer concentration and stirring on the intrinsic viscosity of the polyamide 6-10 solution in m-cresol was measured.

As stirring (RPM) and monomer increased the intrinsic and the polymer yield through a maximum. Diffusion coefficients (D_AB) for hexamethylenedlamine were for hexamethylenedlamine were and were used for the calculations of j_D factors and K/DAB ratios. A relationship and j_D factors was established by a correlation curve.

Development Of An Apparatus To Obtain Temperature Profiles Of Molten Flowing Polymers, Ismail Kemal Saltuk

Theses

The object of this investigation is to develop and test an apparatus to predict temperature profiles of polymer melts in laminar flow in a heat exchanger, with non-isothermal wall conditions.

A commercial polyethylene melt is pumped at various flow rates through a smooth 0.957 in. I.D. pipe. The entrance temperature of polymer is maintained uniform.

Radially distributed six thermocouples (0.062 in. 0.D.) are placed at 2.5 ft. intervals from the entrance of heat exchanger. Immersion of these probes parallel to the flow direction, reduced the errors due to the conduction of heat from the tube wall to the thermocouple stems. …

Correlation And Prediction Of Diffussion Coefficients In Binary Gas Systems, Raymond Gerald Bailey

Theses

A correlation was developed for estimating binary gas diffusion coefficients by the reference substance method, in this case using the viscosity of air and subsequently its corresponding temperature. The derivation was made by the linear least square analysis of 65 different binary systems comprising 161 separate data points at temperatures ranging from 193°K. to 1200°K. At any given temperature only the critical molal volume and the molecular weights of the two gases of interest are required to calculate the diffusion coefficient. The correlation based on the viscosity of air had an average error of 7.67%. The correlation using temperature had …

The Absorption Of Hydrogen Chloride From Dilute Air Mixtures, Edgar L. Demarest

Theses

A study was made of the absorption of hydrogen chloride from air mixtures containing from 1 to 40 mgm. HCl/liter (1000 to 40000 mgm./m.³), using a.4" diameter tower packed with 2" Intalox saddles, irrigated with water or with sodium hydroxide solutions of 0.3% to 3.8% concen?tration. Gas flow rates of 177 to 752 lbs./(hr.)(ft.²) were investigated at three liquid rates: 2960 ; 4260, and 5700 lbs./(hr/)(ft.²). All data were collected below the flooding point.

Correlations of the height of a transfer unit with the superficial gas velocity were prepared for water and for sodium …

Aiir Pollution Emissions From Turbine Powered Aircraft, Raymond Arthur Filippini

Theses

The major pollutants that are emitted by jet aircraft include: particulate matter (soot), carbon monoxide, aldehydes, hydrocarbons, and nitrogen oxides. The first of the pollutants, particulate matter (smoke), constitutes not only a visual nuisance but is also a potential health problem. The rest, which are not visible, are irritants and in high enough concentrations can be toxic.

Since pollutants emitted by jet aircraft are of the same type as those given off by a car, a direct comparison is possible. In one landing take off cycle (LTO), a four engine jet aircraft emits the same amount of particulate matter as …

The Relation Of Heat Transfer To Power Consumption Of Liquids In Turbulent Flow, John D. Bien

Theses

The relationship between the heat transfer ability and the power input requirement of liquid coolants in a turbulent heat transfer condition was investigated. A correlation in terms of the liquid physical properties and the required volumetric flow was proposed and the use of this correlation in selection of liquids as coolant was discussed. The optimum condition for a high heat transfer/power input ratio was also discussed.

Phosphate Removal From Sewage Using A Combination Of Ferric Chloride And A Polymeric Flocculant, Ravindra C. Patel

Theses

The present work is concerned with a newer technique and approach to the problem of phosphate removal from waste water. This includes the removal of phosphate from the sample of activated sludge, i.e., a sample from the aeration tank of the secondary sewage treatment. The phosphate is removed by using ferric chloride as a precipitating agent and a cationic polyelectrolyte (P.E.) as a flocculating agent. Results of this study showed that: (a) P.E. addition gives a significant improvement in phosphate removal over that obtained by ferric chloride alone. In some cases the phosphate removal increased from 92 to 96.5 per …

A Digital Computer Simulation Of A Batch Or Semi-Batch Reactor, Robert Edward Viczorek

Theses

A digital computer simulation of a batch or semi-batch reaction was developed. The system consisted of a jacketed, agitated vessel equipped with a temperature controller modulating a control valve in the stream to the jacket. The reaction was liquid phase, and the jacket medium was liquid.

The program was written in a general form so as to be applicable to any liquid phase reaction with minimum modification.

A numerical technique was employed using initial values of the process variables in the first cycle of calculations for a time interval, and then using average values for further iterations. The simulation proceeded …

Heat And Mass Transfer In The Lyophilizatiuon Of Pharmaceuticals In Vials By Conduction Heating, William Warren Walsh

Theses

This thesis investigates the lyophilization of pharmaceuticals in vials by conductive heat transfer. The process phase diagram and methods of determining the solution eutectic temperature are reviewed. The theoretical considerations of heat and mass transfer pertaining to this process are discussed.

Lyophilization tests of distilled water and of mannitol solutions are used to indicate the relationship between vacuum chamber total pressure and the product/vial interface temperature. Experiments with 10% lactose solutions are used to determine the effect of shelf fluid temperature, product height and chamber vacuum on product/vial interface temperature. Test on a pharmaceutical product are used to confirm the …

The Transferability Of Force Constants Among Olefins, John Martin Comerford

Theses

A normal coordinate analysis of the in-plane vibrations of ethylene was performed using a modified valence force field, a modified Urey-Bradley force field and a hybrid orbital force field. The B_2u species of isobutene was also analyzed. An attempt was made to transfer force constants from ethylene and thereby solve the A₁ species of isobutene, but a solution could not be obtained. This suggests that simple transference of force constants is not feasable in this case.

The potential energy distributions obtained for ethylene are discussed. The normal coordinates calculated in this work are appended.

A Modified Redlich-Kwong Equation For Nonpolar And Slightly Polar Gases, David G. Skamenca

Theses

The PVT prediction capability of the Redlich-Kwong equation is substantially improved through the use of a generalized correlation based on the acentric factor. No experimental data is required to obtain the improved constants. Only the acentric factor and the critical properties of the pure gas are needed. The correlation of improved constants is limited to non-polar and slightly polar pure gases and mixtures in the supercritical temperature range.

The correlation applies to a reduced temperature range 1.00 le; T_R le; 1.60 and a reduced pressure range of 0.030 le; P_R le; 3.00. The correlation reduces deviations by as …

A Computer Program For The Design Of Packed Extraction Columns, George P. Gaccione

Theses

A computer program for the design of packed extraction columns has been developed. This program can operate with a minimum of data of the type that can easily be determined or estimated. The program can be used to investigate design alternates during the preparation of project cost estimates and for the final design of extraction columns.

Viscoelastic Properties Of Polymer Melts, Wu-Shiong Lee

Theses

Thirteen samples of molten polymers were used to test Spriggs and Careau Models. Two empirical equations, one for apparent viscosity and the other which is new, for primary normal stress difference, were checked with these samples also.

In order to test the models, material functions were sought for some specific flow patterns under which the experimental data were collected, and then these functions were compared with data.

Careau Model was found to be better than Spriggs Model in representing molten polymer properties but still yield large deviations. Two empirical equations fitted data quite well and were expected to be useful …

Combined Feedforward-Feedback Control Of A Fluidized-Bed Reactor, Reginald Eugene Mitchell

Theses

Feedforward control, feedback control, and combined feedforward-feedback control were studied on an analog computer to evaluate their effectiveness in controlling a fluidized-bed reactor used for the decomposition of cumene. Proportional, proportional-integral, proportional-derivative, and proportional-integral-derivative modes of control were investigated. Step changes in set-point and load were used as disturbances. The Ziegler-Nichols method and the process reaction curve method of Cohen and Coon were compared in determining values of KC, Ti, and Td which gave optimum control of the fluidized-bed reactor.

Control equation were obtained from the block diagrams of the systems and solved on an EAI TR-20 Analog Computer.

It …

The Application Of A Non-Newtonian Rheological Equation To Low-Density Polyethylene, Jeffrey N. Goldstein

Theses

A generalized non-Newtonian equation describing the rheology of molten thermoplastics is verified for low-density polyethylenes. The equation is extended to account for both rheological temperature dependency and polyethylene molecular weight dependency. The prediction of the rheology of new polyethylenes without additional experimentation is thus possible.

The Computer Evaluation Of The Natural Frequencies Of Vibrating Circular Plates With Free, Fixed And Simply Supported Edges, Thomas Michael Juliano

Theses

The natural frequencies of the transverse vibration of a thin, isotropic, circular plate with free, clamped, and simply supported edge conditions were studied extensively. The frequency equation for each edge condition was derived from the classical partial differential equation of plate vibration. These equations, which are in terms of Bessel functions, were then solved numerically to find the natural frequencies. Since the accuracy of the Bessel function values is very important in evaluating these frequencies, a comprehensive digital computer program was devised to calculate these values to eleven digit accuracy. In this Bessel function program four different methods were required …

The Oxidation Of Sulfur Dioxide In A Regenerative Reactor, Raymond Henry Edgecomb

Theses

A novel dual-unit sulfuric acid converter is depicted that performs in cyclic operation in unsteady state. A mathematical model and IBM 1130 Computer program were developed to show the temperature and conversion profiles in commercial-sized vanadium oxide catalyst beds. In the catalytic oxidation of sulfur dioxide conversions of 95-97% were attained without benefit of conventional heat exchangers. A single exchanger operating in conjunction with the dual-unit system might attain conversions as high as 99%.

Determination Of The Electronic State Of Aryl Nitrenes In An Intramolecular C-H Insertion Reaction, Ali Mohammad Khonsari

Theses

β,γ-Dideuteriopropylbenzene was obtained in 84% yield from deuteration of allylbenzene. Nitration of this compound resulted in o-nitro (β,γ-dideuteriopropyl)-benzene. Reduction of this compound gave o-(β,γ-aideuterio-propyl)aniline. o-(β,γ-Dideuteriopropyl)phenyl azide was prepared by dizotization of the aniline compound, followed by treatment with sodium azide.

Decomposition of the azide in isooctane solution by photolysis at room temperature gave no trace of deuterio-2-methylindoline (intramolecular insertion product).

Photolysis of the azide at the reflux temperature of the solvent (99?C) resulted in the formation of deuterated-2-methylindoline as the major product (40%) yield. The reaction is presumed to proceed through an aryl nitrene intermediate. Analysis of the nuclear magnetic …