Engineering Commons^™

A Comparison Of Backwater Profile Computation, Alwin Chang Hsin Young

Masters Theses

"Bakhmeteff's, Von Seggern's, and the Standard Step methods were chosen for a comparative study of backwater profile determinations made with the assistance of a digital computer. This study concentrated on the M-l type of curves for different kind of prismatic channels; i.e. rectangular, trapezoidal, and parabolic channels. From the results obtained by each method for different channels, the consistency between the several methods and their applicability to all shapes of channel had been studied. Also the effect of the number of reaches used in flow profile determinations, the effect of the use of an average value of (1-ß), hydraulic exponents …

Effects Of Solids On Friction Factor In A Sand-Water Mixture, Frank J. Capek

Masters Theses

"At the present time various industries in both the United States and Europe are very interested in using pipelines as a means of transporting solids. The pumping of solids in pipelines isn't new, however, many of the pipelines in use today were constructed on an empirical basis. This is primarily due to the lack of knowledge concerning the flow properties in fluid-solid mixtures and slurries. With this need for fundamental information in mind, the author made a study on the effect solids have on the friction factor in fluid-solid mixtures.

In this paper various percentages of fine and coarse sand …

The Analysis, Construction, And Calibration Of An Electronic Vibrations Amplifier, Jimmie D. Howard

Masters Theses

"Vibrations analysis necessitates having a device capable of performing some initial phase of detection. The vibration amplifier presented in this thesis performs such an initial aid to analysis by detecting amplitudes of vibrations of varying magnitudes and frequencies. This is accomplished by utilizing a Piezoelectric crystal vibration pickup to obtain an acceleration wave form. Two operational amplifiers perform integrations of the acceleration to obtain displacement. A calibrated meter within the device provides a method of determining magnitudes of displacement. Recording instruments such as the Brush recorder or an oscilloscope may also be used"--Abstract, page ii.

A Study Of The Hood Inlet And Its Possible Use As An Overflow Structure For A Sanitary Lagoon, Richard Irwin Boe

Masters Theses

"A closed conduit, such as an overflow pipe for a conservation pond or a sanitary lagoon, will not flow full if laid on a slope that is hydraulically steep unless the pipe entrance receives special attention. A steep conduit slope is necessary to insure that the pipe entrance controls flow.

The recently introduced hood inlet will permit the closed conduit to flow full, even if on a hydraulically steep slope, upon a slight submergence of the inlet crown. The hood inlet is formed by cutting the pipe at an angle so that the crown of the inlet projects beyond the …

The Effect Of Phosphoric Acid On Compaction And Shear Characteristics Of Pure Kaolin Clay, Bhupat Hargovinddas Mehta

Masters Theses

"The work presented is the investigation of the effect of phosphoric acid on the compaction and shear characteristics of pure kaolin. Pure Georgia kaolin clay average particle size of five microns was mixed with different percentages of phosphoric acid. These mixtures were permitted to react for varying periods of time. The results of the study indicate a notable and gradual increase in dry density of the kaolin with increasing percentages of phosphoric acid admixture. The acid admixture ranges from one up to nine percent of the dry weight of the clay. Increase in cohesion of the clay with increase of …

Analyses Of Two New Electrode Configurations For Earth Resistivity Surveying, Chi-Chao Chang

Masters Theses

"Two new electrode configurations for the electrical resistivity- surveying are introduced: the A-configuration, consisting of a closely spaced pair of current electrodes separated at larger distance from the closely spaced pair of potential electrodes, and the B-configuration, in which each closely spaced pair consists both current and potential electrode. Because electrode pairs can be carried as units, the new configurations can be applied to continuous resistivity surveying more easily than the Wenner configuration....

Theoretical apparent resistivity values are derived, by Maxwell's theory of images, for the A- and B-configuration over a two layered earth using the depth probe method, and …

Evaluation Of Protective Paint Films On Steel By X-Ray Diffraction Techniques, Donald Charles Knobeloch

Masters Theses

"Paints and related organic materials provide the most widely used means of protecting metals against corrosion. While corrosion measurements are based on a full range of quantitative methods in physical and analytical chemistry, the basic problem of evaluation work in the field of paint chemistry has been characterized by empirical testing procedures. Field tests are still of major importance and secondly, the relative value of paints may be predicted through exacting laboratory tests. However, the results of accelerated exposure tests have never successfully been correlated with service experience despite the efforts of many laboratories over a period of 35 years …

Effect Of Boundary Layer Control, Through Spiral Cuts, On The Film Coefficient Of Convective Heat Transfer, Nicholas W. Barre

Masters Theses

"This thesis is experimental investigation into the possibility of obtaining an increase in the forced convection heat transfer coefficient for a pipe by passing the fluid through a narrow spiral cut in the pipe.

Different spiral pipes with pitches of two, four, eight, ten, sixteen, and twenty inches were used; however, the width of the spiral cut remained unchanged at 3/16 of an inch. Several mass flow rates for water were used up to a maximum of 1536 lbs/hr for each run.

One of the objectives was to find which pitch would give the highest heat transfer rate for a …

A Study Of The Transient State Of Transpiration Cooling, William C. Wolkenhauer

Masters Theses

"This thesis is a successful attempt to show a new approach to the transpiration cooling problem. Transpiration cooling has long been known as an effective way of removing heat from porous material.

It is shown here that transpiration cooling from a porous material, assuming a temperature difference between the coolant and the porous material, is less effective than where the coolant within the pores is assumed to be at the same temperature as the material adjacent to the pore. Previous investigators made the latter assumption.

The specific problem considered here is that of a uniform, porous plate with constant physical …

Preliminary Study Of An Optimum Vibration Absorber For A Multi-Mass System With Multiple Excitation, John Raymond Burrows

Masters Theses

"The object of this thesis is to demonstrate, by the use of a modern digital computer, a fast, efficient method to eliminate or minimize undesirable stress conditions in a multimass vibrating system with multiple excitation. The condition desired is obtained by the addition of an optimum tuned and damped dynamic vibration absorber, for one critical speed only.

Maximum stress is the criteria used for design here and not amplitude as has been used previously by all other authors.

This solution requires the applied torque to be reevaluated as an average torque and a number of half integer harmonics. This method …

Isothermal Decomposition Of Austenite (In 1.4% Tungsten Steel) At Subcritical Temperatures, Samir Moustafa Riad

Masters Theses

"An experimental investigation was conducted in order to study the relationship between temperature, time and the decomposition of austenite in Tungsten steel of a given composition - and to plot the T-T-T Diagram for this steel.

The steel was prepared, homogenized and cut into identical specimens for further heat treatment and metallographic inspection. Precautions were taken to prevent these specimens from decarburizing during any heat treatment.

This experimental work may be divided into three main parts:-

I. Determination of the critical temperature range; i.e. the range of temperature Ae₁ and Ae₃ above which austenite is stable and below …

Transpiration Cooling Of A Plane Porous Plate, Raymond George Posgay

Masters Theses

"The transient temperatures were determined in a porous plate for one dimensional heat flow and one dimensional counter coolant flow. One surface of the porous plate was heated by a hot gas by convective heat transfer. A general discussion of the problem is considered and the procedure described for working all such problems dealing with transpiration cooling.

The solution of such problems is illustrated by two examples employing a ceramic plate one inch thick and cooled by a uniform flow of air in a direction counter to the flow of heat, while one surface of the ceramic plate was heated …

Impact Energy Coupling And Impact Seismic Refraction Using Electronic Timing, Roderick D. Carroll

Masters Theses

"The use of impact energy sources in lieu of explosives for shallow seismic investigations is limited chiefly by the low energy available. Means of increasing the energy transmission of an impact source are investigated, using a weight drop arrangement and an oscilloscope. The energy of refracted arrivals is investigated by direct overburden impacts, compaction of the overburden at the point of impact and the use of steel and aluminum plates as coupling devices. Energy transmission is shown to be greatly increased, using a suitable coupling device and the conditions for optimum coupling are discussed. The elastic constants of the ground …

An Analog Method For The Determination Of The Deflection Of Beams Resting On End Supports And Design Of An Automatic Programming Device, Paul C. Jackson Jr.

Masters Theses

"This investigation shows that beam problems can be solved easily and accurately with an analog computer. Two problems were solved as to their shear, moment, slope and deflection along the length of the beam and the graphs drawn by the analog computer were compared with calculated values. Very little difference was found between them.

An electronic programmer was built to aid in handling beam problems as they were being run on the computer. This was capable of putting into the computer bits of data at specified intervals of time. The programmer proved reliable and repeatable once it was adjusted to …

Investigation Of Vertical Internal Spillways, Paul R. Munger

Masters Theses

"This investigation resulted in the development of a means of predicting the discharge of water through an internal spillway type rockfill dam. From the data obtained during the various tests, equations were developed by which the coefficient of discharge for an internal spillway type rockfill dam can be determined when the core height, rock size and head causing flow are known. The equations give results with an error of less than 5%, which is adequate for engineering works"--Abstract, page 2.

Transient Temperature Distribution In Solid Sphere Subjected To Radiation Heat Exchange, William H. Stocklin

Masters Theses

"The author believes that numerical analysis is the most feasible approach to calculating the transient temperature distribution in a solid sphere subjected to various surface conditions; heat flow within the sphere is radial.

Numerical analysis is employed to arrive at a series of equations for calculating the transient temperature at selected points of a solid sphere. A study is made to determine a method for calculating temperatures with these equations; a computing device is found to be the most practical method for this purpose. The equations for temperatures at internal points of the solid sphere are general.

The equations have …

Electron Microscope Study Of The Systems Cadmium-Cadmium Chloride And Lead-Lead Chloride, Dennis O'Neill

Masters Theses

"The nature of the dispersed phase in the cadmium-cadmium chloride and lead-lead, chloride systems were investigated with the electron microscope.

Preliminary experiments on preparing and examining the dispersed phase showed that it was most feasible to study the material by electron-microscopic examination of replicas made from the surfaces of the fractured materials. Melting apparatus and methods were chosen so that samples of the melts could be easily quenched to different temperatures and so that the samples could be easily fractured with a minimum of surface contamination. Of the conventional replicating techniques tried, that of carbon replicas pre-shadowed with chromium was …

Effect Of Deflections For A Flat Plate By Slope-Deflection-Gyration Method, William Hsin-Loo Ying

Masters Theses

"Since the procedure for the theoretical solution of a rectangular flat plate or slab is complex, many approximate methods for determining the moments and deflections of such plate have recently been developed. One of these methods is the so called Slope-Deflection-Gyration Method which is performed by means of basically well-known structural theories - slope-deflection and torsion.

For a given plate, it is assumed that the plate is to be divided up into a grid of strips or equivalent beams at right angles to each other. The joints of this grid are assumed to be rigidly intersected and be permitted to …

Apparatus For Inductive-Electromagnetic Model Studies, Won Ho Kim

Masters Theses

"The object of this research is to design, construct and calibrate an apparatus suitable for electromagnetic model studies. A portion of the thesis is devoted to general review and theoretical consideration of electromagnetic prospecting.

Theoretical analysis of electromagnetic survey data by mathematical methods can only be carried out for simple idealized subsurface conditions. Because of the difficulties of theoretical solutions, in contrast to the simplicity of the conditions of similitude in electromagnetic exploration, a model experiment offers a very useful means of studying and comparing the response of naturally occuring conducting mineral bodies.

An apparatus suitable for inductive-electromagnetic model studies …

The Effect Of The Ultraviolet Portion Of The Sun Spectrum On Chlorine Residuals In Water Supplies, Tumkur Mohmed Ameer Ahmed

Masters Theses

"The effect of sunlight on chlorine residuals in water supplies was investigated to provide original and basic information of value to the water purification field.

Three different water systems were employed: (a) The Simplified Water System, (b) The Ground Water System, and (c) The Surface Water System. The RS Sunlamp provided an appropriate source of ultraviolet radiation. A 10 mg/1 chlorine concentration was used. The pH values of 7 and 10 and the illumination intensities of 145 and 200 foot candles were employed. Iodometric determination of chlorine residuals was the main parameter used.

It was found that the chlorine residuals …

Transpiration Cooling, Herbert S. Brahinsky

Masters Theses

"In the investigation of the problem, it is shown that the process of transpiration cooling is an effective method of cooling. This process may be applied to heat screens or heat shields, as was done in the sample problems worked out here. A porous plate with coolant flowing counter to the flow of heat was used.

The plate temperature is determined by the amount of heat flux, coolant flow, thermal conductivity of the material used as a plate, the specific heat of the fluid, the specific heat of the plate material, the density of the plate material and its porosity. …

Some Aspects Of Miscible Phase Displacement As Applied To The Recovery Of Oil Reservoir Crude, David D. Friend

Masters Theses

"Recent application of the miscible sing displacement process as a method to increase recovery from petroleum reservoirs has resulted in a great deal of laboratory investigation, none of which provided conclusive evidence as to the amount of mixing taking place between the displacing and displaced fluids. This investigation attempts to provide a possible insight into the rate and degree of mixing of two fluids with respect to flow path transversed and the rate of advance of the fluids. The laboratory investigation consisted of displacing a fluid from a packed core with another fluid under completely miscible conditions.

Experimental evidence indicates …

Deformations And Bending Moments For A Building Slab With A Central Opening, Wu Ping-Yung

Masters Theses

"The adaptability of the classical slope-deflection method analysis to the analysis of uniformly loaded building slab is the subject of this study. The paper demonstrates the use of slope-deflection in computing deflections and bending moments in uniformly loaded square building slabs both with and without central square openings. The results obtained are compared with results of other methods found by other investigators.

Numerous methods have been proposed for use in solving plate or slab problems. The exact solution in the form of a fourth order partial differential equation has proved to be of value in relatively few cases where boundary …

Effect Of Lime & Cement Additives On The Dynamic Modulus Of Elasticity Of A Clay Soil, Ismail Yolar

Masters Theses

"This thesis is a study to determine the values and characteristics of modulus of elasticity and the modulus of rupture of a clay soil stabilized with lime and cement in an effort to pave the way for including these values in design criteria.

The modulus of elasticity and the Poisson's ratio were obtained by sonic method. Specimens were broken in flexure for modulus of rupture. Experiments were performed with; (1) untreated soil, (2) soil with 4, 6, and 12 percent cement additive, (3) soil with a 3 percent lime additive and 0, 4, 6, and 12 percent cement additive, (4) …

A Vacuum Induction Furnace For Pyrometric Cone Equivalent Determinations, Robert E. Farris

Masters Theses

"Various furnaces which are commonly used for P.C.E. determinations were compared from a literature review. The inadequacies of these furnaces were noted and a furnace was designed, constructed, and evaluated in an effort to minimize or eliminate some of the indicated problems. For this furnace heat is developed in opposed cones (susceptors), which are fabricated from 0.005” molybdenum sheet, by induced (induction) currents from a 10 KW vacuum tube generator. The furnace components are enveloped by a pyrex cylinder in which a vacuum (approximately 1 to 5 micron pressure absolute) is maintained during operation"--Abstract, page ii.

Design Of A Square Loop Magnetic Integrating Device, Fred Leland Grismore Jr.

Masters Theses

"The problem investigated in this research was the development of a static integrating circuit applicable to closed loop feedback control systems. Investigation of various methods of attack indicated that square loop magnetic cores offered characteristics required for the integration process. These include the ability to sum input information and the ability to store information for an indefinite period of time.

An experimental program was carried out, investigating the various properties of square loop magnetic materials and required design parameters. Through this work it was verified that the process of integration could be realized by using the partial switching volt-second absorption …

A Study Of The Energy Dissipation And The Related Pressures And Velocities Of Cylindrical Tank Type Stilling Basin, Graham Wayne Wood

Masters Theses

"In all hydraulic structures that hold back water, whether for the purpose of power, irrigation or flood control, all must have some means of dissipating the energy that is produced by the movement of the water from the pond or reservoir to the tailrace. The method of dissipation depends largely on downstream conditions, terrain and economics. The dissipator is to prevent scour and the undermining of the dam itself. The construction of any type dissipator should be the best one available for the least cost of construction. However, space limitations may dictate another type of dissipator. It has been recommended …

An Investigation Of The Factors Influencing The Design Of A Dense Prilled Ammonium Nitrate-Fuel Oil Mixture, Robert Bartley Hopler Jr.

Masters Theses

"The physical characteristics of dense ammonium nitrate prills were examined. The density was found to be 1.52 grams per cubic centimeter, and from this the specific surface was calculated for the size fractions of interest in the investigation. Theoretical loading densities were calculated for between 26.0 and 47.6 percent voids.

The explosive properties of discrete particle size fractions were investigated. The equation by Clark was found to predict the detonation velocity of the sizes smaller than 8/20 mesh. The equation by Cook could not be applied to dense prilled ammonium nitrate. The possibility of a very oxygen negative condition existing …

Underground Methods Of Working Coal, Hemendra Nath Datta

Masters Theses

"'Underground Methods of Working Coal' is the subject of this thesis. It is the purpose of this investigation to summarize all the mining methods under various conditions of working.

The underground methods of mining have been classified under three headings; viz., (a) Room and Pillar, (b) Longwall and (c) Horizon Mining. The conditions suitable for the applicability of each system and their relative merits and demerits are fully discussed.

The principles of the design of the workings of both room and pillar and longwall systems to have effective roof control in the area of the workings are pointed out.

Distinct …

Explosive Performance Parameters: A Digital Computer Solution And Error Analysis, Robert T. Stelloh

Masters Theses

"A program was written for the determination of explosive performance parameters on the Royal-McBee LGP-30 electronic digital computer. The method developed by Dr. M. A. Cook was used, which is based on the thermohydrodynamic theory of detonation. This theory and the specific equations developed by Cook are presented.

General statements are made in regard to computer programming, and specific information given concerning the programming concepts used for this particular problem. A detailed explanation of the program operation is given, together with the tabular data required for its use.

Equations are presented for an analysis of the effects of roundoff error …