Engineering Commons^™

Study Of The Design Of Reinforcement For Prestressed Concrete And Blocks, Charles Robert Hoffman

Masters Theses

"This thesis is an analysis of the transverse tensile stress condition in an end block of a prestressed concrete beam. A stress analysis was made by photoelasticity and compared to the mathematical solutions and experimental solutions performed by others on concrete models. The photoelastic model was made from a piece of Columbia Resin, 39.

Whatever method is chosen to determine the stress condition, there is no exact code that can be established to fit the various type problems which arise"--Abstract, page 1.

Model Analysis By The Moiré Method, David D. Kick

Masters Theses

"This study presents the use of Moiré fringes for model analysis of deflections and strains. Deflection of a beam, strain in a disk, and an Influence diagram for a frame are presented as examples of uses of the Moiré method. The necessary equations for the determination of strain using the Moiré method are also derived and presented in this work"--Abstract, page v.

Gathering Haunch Design Data By Photoelasticity, Richard B. Heagler

Masters Theses

"The haunching of beams and columns and the haunching of rigid frames is performed by design engineers for the purpose of relieving stress concentrations that might occur at discontinuities in structures. The haunch performs this relieving of stress concentration by increasing the rigidity of the structure at regions of high stress. Usually this design step is one of trial and error; that is, the engineer will select a haunch or method of haunching and then check to see if the result is sufficient for his purpose. This can be a time consuming process and can lead to uneconomical design.

In …

Fractionation Of Fission Elements By Electrodialysis, George Joseph Bub

Masters Theses

"The development of nuclear power has presented countless problems to the scientists and engineers of today. A problem of extreme importance is the disposal of radioactive wastes. Another is the recovery of some of the useful radioisotopes from fission product waste solutions. This investigation is concerned with the recovery of some of the fission elements for use in radiochemical and medical research and in industry.

At present little effort is made to recover useful fission elements. The fission product waste solutions are treated to reduce the volume and are stored until the radiological hazard is reduced and are then disposed …

Refrigeration Heat Transfer Characteristics Of An Artificially Cooled Trout Pond, Richard G. Murray

Masters Theses

"In many locations natural summer lake and pond temperatures are too great for the practical production of trout for fishing purposes.

The purpose of this thesis is to investigate the refrigeration capacity required to maintain a pond of water at a temperature that provides a healthful environment for trout.

The over-all refrigeration load for this application was sub-divided into four categories; conduction, convection, evaporation and radiation. Each type was solved by analytical means using suitable boundary conditions and simplifications. It was necessary to determine one boundary condition for the conduction heat transfer by an empirical method.

The results of this …

Porous Cooling Of A Pile, Tarsem Singh Purewal

Masters Theses

"In this investigation the problem of a limiting case of steady state one dimensional solid-fluid Newtonian heat transfer is examined in which an incompressible non-heat generating coolant fluid is flowing through a heat generating porous plate.

The effect of grain size on the Newtonian heat transfer in the porous plate with various kinds of internal heat generations is determined analytically. The temperature difference between the solid and the coolant fluid through the porous plate is determined. All the previous studies assume that in the porous plate, coolant fluid temperature and solid temperatures are approximately equal. This analysis eliminates this simplifying …

A Study Of A Second-Order Predictive Control System, Tarkeshwar Singh

Masters Theses

"The purpose of this thesis is the study of a predictive control system by simulating it on an analog computer. Logic criteria for step reference inputs are derived by the phase- plane technique, and tie corresponding logic network designed to bring the error and error rate of the controlled system toward zero in the least possible time.

The responses of the predictive control system for step, ramp, sinusoidal and exponential reference inputs are investigated with primary emphasis placed on the rise time and overshoot for several values of step inputs of the reference.

Finally, recommendations are made for further investigations …

The Dissolution Of Magnesium In Strong Acids, Baldev K. Bhatia

Masters Theses

"The rapidly growing demand for magnesium and magnesium-base alloys in the manufacture of aircraft has led to a great amount of research into the corrosion characteristics of these materials. The result of such research has been the development of suitable magnesium alloys and protective coatings to retard corrosion.

The standard electrode potential of magnesium lies between -2.35 volts and -2.54 volts at 25⁰C (hydrogen scale). Thus, magnesium lies next to aluminium in the electrochemical series of elements. The atmospheric corrosion of magnesium has been studied under conditions of indoor and outdoor exposure. Under these conditions the initial attack is formation …

A Study Of Several Commercial Steels In The Red Short Range, Jorge Alberto Espana

Masters Theses

"The red short phenomenon present in steel, was studied by means of torsion tests at temperatures between 800 and 1200⁰C. Cold drawn bars of different compositions of steels were tested, and the number of turns to failure and maximum twisting torque were plotted versus temperature.

All the steels tested, exhibited to have a certain degree of red shortness. By comparing the curves and the respective chemical analyses, the detrimental effect of sulphur and lead and the beneficial effect of manganese, was established.

Microscopic examinations revealed the intergranular nature of the cracks in the red short range. Sulphur and oxide distribution …

A Study Of Small Watersheds Within The State Of Missouri, Terence E. Harbaugh

Masters Theses

"The present status of data from watersheds in the under 10 square mile drainage area classification, pages much to be desired. However, this study of 45 small watersheds within the State of Missouri gives an indication that surface runoff from these basins may be predicted with a fair degree of accuracy. The inclusion of a shape factor AL² and its use as a portion of the "basin index" (AL²S^1/2) gives accurate results as a predictor of the "mean annual flood". The mean annual flood may be adequately computed by the formula, MAF = 113(AL^{2 …}

A Theoretical Study Of The Mechanism For The Haeffner Effect, David Charles Jacobs

Masters Theses

"In 1953, E. Haeffner reported that when he had passed a direct electric current through a length of capillary filled with liquid mercury, the lighter mercury isotopes were enriched at the positive terminal and the heavier mercury isotopes were enriched at the negative terminal. This phenomenon is referred to as the Haeffner Effect. Since Haeffner’s original experiment, other investigators have obtained similar results in other liquid metal systems.

When a direct electric current passes through a metallic conductor a free energy gradient is established. The direction of the negative free energy gradient is in the direction of the positive terminal. …

A Study Of Heat Transfer Coefficients On Cylindrical Pipe In Turbulent Flow, Dennie Lee Adkins

Masters Theses

"This thesis represents a study of the effects of turbulent motion on heat transfer coefficients on cylindrical pipe.

The turbulent motion was created by cutting transverse slots in a spiral configuration along the pipe length.

An induction heater was used for the heat source and water as the cooling medium. The water was conducted over the pipe surface and through the slots.

This caused the laminar layer along the pipe surface to be broken up and an increase in the heat transfer coefficient was experienced.

The main objective of this test was to find if a relation existed between the …

Shear Stress Distribution In Haunched Beam Models, Manyu K. Mehta

Masters Theses

"The purpose of this thesis has been to give the distribution of shear stress inside a haunch. A haunch is generally provided to relieve high stress concentrations at the face of the column. However the nature of shear stress distribution inside the haunch is not known.

This stress distribution was determined from a photo- elastic study on a CR-39 model. It is noted that the haunch reduces the stress concentration at the face of the column but at the same time somewhere near the point where the haunch meets the beam there is a high stress concentration.

Shear stress changes …

Development Of A Simple Bar Method Thermal Conductivity Test, V. J. Flanigan

Masters Theses

"A linear flow bar method type apparatus was set up for finding thermal conductivities by comparison techniques. Comparison technique consist of using a standard specimen where the thermal conductivity is known and comparing it to the unknown specimens to find their conductivity. Apparatus of this type usually uses thermocouples for the required temperature measurements, but thermistors were used in this experiment. The thermistors used required calibration to measure accurate temperatures and this was accomplished by using the known temperatures of the changes of state of some common materials. Five alloys were used to evaluate the method: SAE 1020 steel, gray …

Velocity Distribution Induced By Free Jet Impact On A Stilling Basin, Sedat Özkol

Masters Theses

"At present, the use of the free jet impacting on a stilling basin as an energy dissipator is not very common, as there is very little information available concerning this particular field. However, if conditions are favorable, this type of energy dissipator will be quite economical to construct.

In this paper it was found that the hydraulic behavior of the free jet impacting on a stilling basin can be determined to a degree which may be considered accurate for practical purposes. It was also shown that given the free jet velocity, the magnitudes of the velocities at the critical points …

The Effect Of The Rolling Load On The Micro-Structure Of Low Carbon Sheet Steel, Jerry Lee Cadden

Masters Theses

"A Stanat 315, two high-four high, combination rolling mill is used to cold roll annealed, low carbon steel strips. A method of measuring the rolling load was presented. The method consisted of constructing a load cell using SR-4 strain gages attached to a steel column. The load cell was placed under the hold down screw of the rolling mill and a known load was applied. The stresses from this load were transferred to the mill housing where another SR-4 strain gage was located. The strain in the mill housing was recorded at the corresponding applied load. During rolling, the strain …

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

A Weight Loss Technique For The Determination Of Phase Boundaries, Robert Lee Benner

Masters Theses

"An apparatus has been designed and constructed that would continuously record the weight loss of a sample in a flowing inert atmosphere, at a constant temperature.

A technique has been developed to determine the phase boundaries of a binary phase diagram.

Alloys of the magnesium-nickel, cadmium-antimony, copper-cadmium, copper-zinc, and magnesium-zirconium systems were subjected to investigation to verify the operation and resolve a number of limitations of the equipment.

These investigations disclosed that the apparatus gave the best results with alloys having vapor pressures in the range between 1 and 35 millimeters of mercury"--Abstract, page 2.

Linear Feedback Control System Compensator Design Under Specified Constraints, Keikhosrow Irani

Masters Theses

"The purpose of this thesis is to find the necessary and sufficient conditions for the design of compensators, following the concepts developed by Ross, Warren, Hsu and Sanden.

The main object that motivates this investigation is to design the lead or lag compensator networks for a given linear feedback system when there are these constraints.

1. Gain of the system is constant.
2. The steady-state error is invariant.
3. The dominant poles of the closed-loop transfer function are specified.

Consideration of the problem is in two parts:

• a. Derivation of necessary and sufficient conditions of compensator design that fulfill the three constraints.
• b. …

Analysis Of Flat Plates By Reaction Distribution Method, David D. W. Yang

Masters Theses

"This study was made to analyze rectangular flat plates by the method of Reaction Distribution and to compare results obtained by this method with that of other methods. The basic approach is to divide the plate into an equivalent grid system and introduce temporary supports at the intersecting joints. The results from this study shows that the Reaction Distribution method is useful in a qualitative analysis of the behavior in a plate but is less satisfactory in obtaining reliable quantitative results"--Abstract, page 2.

Mechanics Of The Voussoir Arch As Applied To Block Caving, Christopher Haycocks

Masters Theses

"The theories of ground failure in massive rock with special reference to the problem of the mechanics of block caving were studied and evaluated.

The mechanics of arch or dome formation underground were studied quantitatively using the Voussoir arch theory. The effect of shear stress on the arch stability was considered and found to affect the system only when the arch height increased beyond certain limits.

A theory of the mechanism of ground failure in an undercut block using the dome theory was advanced. Photo- elastic model studies were used to support the conclusions reached"--Abstract, page i.

A Study Of The Permeability And Separation Of Carbon Dioxide And Hydrogen By Gaseous Diffusion Employing Barriers Of Polystyrene, Carl J. Wallace

Masters Theses

"The purpose of this investigation was to study the permeability and separation of carbon dioxide and hydrogen by gaseous diffusion employing barriers of polystyrene. The offset of temperature and barrier thickness on the permeability and separation of carbon dioxide and hydrogen wore Investigated for barriers of one, three, and five-mil thicknesses and for temperatures of 26, 35, 45, and 50 degrees centigrade.

With an increase in barrier thickness of one to five- mils, the permeability of carbon dioxide decreased to one-fourth of its value at the one-mil thickness. The hydrogen permeability decreased to approximately two- thirds of its value at …

A Study Of Composite Beams Made To Find An Approximate Relationship Between The Top And Bottom Flange Steel Ratio, Murli U. Hasrajani

Masters Theses

"At present in building construction the use of the composite beams is not very common. The use of the concrete beams is seen in almost all construction. By using composite beams in building construction more durability and savings in cost could be achieved. This paper shows an approximate design procedure which could be followed without running a number of trials with different sections to arrive at the required one. The ratio of top flange steel to the bottom flange steel can be determined if one knows the loads, span and the depth of the beam required"--Abstract, page i.

Experimental Stress Analysis Of Bolts In A Flange Coupling, Vijay Rastogi

Masters Theses

"In this investigation an attempt has been made to determine simple formulae leading to a better, more useful and much safer design of flange coupling bolts. The bolts were tested under tensile loading and bending and hence the results obtained apply for bolts under these modes of loading only.

The behavior of flange bolts under different initial tightening torques was studied by measuring strains in a bolt on which strain gages had been attached* . From this, the load producing separation of flanges, under different tightening torques, was determined and used in deriving formulae for prediction of the load for …

A Model Study Of The Behavior Of Elastic Liners In Shallow Underground Openings, Martin Samuel Oudenhoven

Masters Theses

"Models of epoxy resin were used in a stress freezing technique to determine areas of possible failure in lined circular openings. These models were loaded in a centrifuge for a fixed period of time, after which they were analyzed photoelastically. The material characteristic changes, with time, were recorded on graphs and used in the analysis.

Two types of tests were conducted; one, where the lining thickness was changed and, the other, where materials of the liner and plate material were changed.

The resulting analyses furnished proof that the greater the rigidity of the lining, the higher the stress developed in …

A Comparison Of A-C And D-C Lead Compensation From D-C Prototype Networks, Piyush Parikh

Masters Theses

"The object of this thesis is to study the difference in transient and frequency response characteristics between a prototype d-c phase lead compensating network and an equivalent a-c phase lead compensating network.

A second order servo is selected to be compensated and five d-c prototype and equivalent a-c phase lead compensating networks are designed. The frequency characteristics of the a-c networks are obtained experimentally and these of the d-c networks are obtained analytically. The characteristics of both networks are compared and their differences are studied. The transient characteristics of the d-c and a-c compensated closed-loop systems to a step input …

A Model Study Of The Induction Log Applied To The Detection Of Asymmetrically Located Orebodies, Robert Walter Piekarz

Masters Theses

"This research project was undertaken to determine the possibility of using an induction log of the type applied in petroleum exploration, for the detection of conductive ore- bodies asymmetrically located with respect to a borehole. Since a mathematical analysis would be extremely complex, a model study was conducted, using graphite bodies of various shapes to simulate different modes of mineral occurence.

The investigation showed that these bodies were readily detectable, and were capable of yielding anomalous curves characteristic of their geometry. The values of apparent conductivity decreased rapidly with lateral displacement, from the logging tool, as expected, due to the …

A Model Study Of The Application Of Roof Bolts Under Unsymmetrical Loading Conditions, Friedrich H. K. Esser

Masters Theses

"When coal is extracted by the long wall mining method, two gate-roads on either side of the working face are driven with the advancing operation. In the surroundings of these openings the state of stress which existed prior to mining is not only disturbed by the drifting process of the gate-roads but also by the coal extraction in the long wall, resulting in an "unsymmetrical" stress distribution. Varying incremental pressure components and the high complexity of strata movements make it extremely difficult to control the rock behavior under unsymmetrical conditions by conventional support. Application of roof bolts as an auxiliary …

A Correlation Of Heat Transfer Coefficients Using An Induction Heater, Charles Maurice Martin

Masters Theses

"This thesis represents a study of the following problems. (1) Determination of techniques and equipment which would give satisfactory correlation of experimental heat transfer coefficients with those obtained from acceptable heat transfer equations when using an induction heater as the heat source. (2) Determination of depth of energy deposition in a thick-walled tube due to induction heating.

Techniques were developed that gave a correlation between experimental and calculated coefficients that were within -5% for minimum flow and +8% for maximum flow.

Because of difficulties in positioning thermocouples, the depth of energy deposition could not be accurately determined. However, two surface …

A Comparison Of The Load Carrying Characteristics Of Hydrostatic Thrust Bearing Using Monatomic, Diatomic, And Triatomic Gases, Joseph C. Pigott

Masters Theses

"The purpose of this investigation is to compare the load carrying characteristics of gases with different ratios of specific heat. The design, construction, and operation of an apparatus for testing and comparing the load carrying characteristics of gases are described. Several monatomic, diatomic, and triatomic gases were tested and the results evaluated and compared. The data are tabulated and displayed in a series of curves.

It was found that the monatomic gases exhibit a greater clearance for a given load and a greater total load carrying capacity than the diatomic gases which in turn have a greater clearance and total …