Engineering Commons^™

A Determination Of The Rate Of Evaporation Of Zinc At Atmospheric Pressure., Yu Ming Su

Masters Theses

"Measurements of evaporation rates of zinc in three different residual gases, e.g., argon, carbon monoxide, and hydrogen at one atmosphere pressure, were made. It was found that the rate of evaporation of zinc in one atmosphere of argon was almost the same as that in carbon monoxide, while the rate in hydrogen was almost twice the rate in argon or carbon monoxide. Measurements of evaporation rate of zinc in one atmosphere of argon-oxygen mixtures were also made. The evaporation rate was considerably reduced because the formation of the oxide film retards the zinc vapor escaping from the evaporating surface"--Abstract, page …

Hydrologic Characteristics Of Shallow Bedrock Aquifers In The Vicinity Of Norman Creek, Central Phelps County, Missouri, Michael A. Nawrocki

Masters Theses

"Groundwater is becoming increasingly important as a source of water supply in the United States. Consequently, the prediction of well yields is a vital concern. In order to predict the quantity of water which can be reduced from a given aquifer it is necessary to know the aquifer's hydrologic characteristics. Many theoretical formulae have been derived for determining the aquifer characteristics. To date, these formulae have been tested mainly on unconsolidated and clastic rock aquifers. It has never been shown that these formulae can also be consistently applied to carbonate aquifers which underlie regions of karst terrain. This paper summarizes …

The Design, Development, And Manufacture Of A Tool Grinding Fixture, Lawrence Carrell Jr.

Masters Theses

No abstract provided by author.

The Design And Construction Of An Apparatus For The Plane Wave Analysis Of Mufflers, Stephen Philip Buckley

Masters Theses

"In the following report, a method for evaluating the attenuation characteristics of a general muffler as well as the design, construction and use of the associated apparatus are described. The method combines accepted plane wave theory and experimental techniques into a relatively straightforward approach to the analysis of acoustic filters. Equations are developed to cover the frequency range between 300 and 4000 cycles per second. Deviations from these equations extend the use of the equipment to low frequencies without the need for unduly long and cumbersome apparatus. This method, which may be called the standing wave method, utilizes a standing …

A Study Of Film Boiling Of Liquid Nitrogen And Liquid Argon Over A Wide Pressure Range With Cylindrical Heaters, V. J. Flanigan

Masters Theses

""A film boiling heat transfer study was conducted with three different diameter cylindrical copper heaters over a wide range of pressures for nitrogen and argon with the heat transfer surface in the horizontal position. The data were compared to the commonly used film boiling heat transfer relations. The common relations were found to be considerably in error for the range of variables covered in this investigation. A semi-empirical equation for corresponding states fluids which correlates the available data as a function of the reduced temperature and reduced pressure was derived and discussed"--Abstract, page iii.

Determining The Transfer Matrices Of Tapered Multiwire Transmission Lines, Clyde A. Vandivort

Masters Theses

"The advent of monolithic and integrated microelectronic circuits has aroused interest in passive multilayered thin film networks. The basic thin film network is shown in Figure 1. This structure consists of alternate resistive and dielectric layers sandwiched together. Such devices are referred to as distributed parameter RC networks. The reduction of volume and increased reliability offered by thin film devices has caused considerable effort to be extended in the analysis of their characteristics....

The incremental equivalent circuit given in Figure 2 stems directly from the above physical parameters and is the circuit used as a basis for the analysis that …

A Comparison Of Strength Properties Of Heat Treated Aisi 1065 Steels At High Strength Levels, Robert Lowell Hollenbeck

Masters Theses

"Six AISI C 1065 steels were heat treated and tensile tested in order to evaluate their ductility at high strength levels. Heat treating and tensile testing procedures were developed for use working with these steels at tensile strengths of 300,000 psi and higher. The austenitizing procedure in the hardening operation was found to affect the strength and ductility of the high strength samples. Rapidly heating to the austenitizing temperature followed by an immediate quench produced better properties than slow heating followed by a soaking period before the quench. However, it was concluded that the carbon contents of the steels studied …

A New Performance Index For Sensitivity And Energy Optimization., Mohamed Zafer Dajani

Masters Theses

"The principal aim of this thesis is to present a new index of performance which when minimized will simultaneously optimize the system energy and sensitivity function of a multivariable linear control system. With this performance index it is usually desirable to discriminate between the sensitivity factor and the energy term by weighting them differently. Two types of weighting factors are presented. Since it is not easy to minimize that performance index for all types of problems, further research is suggested to find methods of solution for such problems. Illustrative examples demonstrate the optimization process and the type of assumptions needed …

A Study Of The Compressibility Of Silty Soils., Marvin L. Byington

Masters Theses

"This study has been conducted to determine the applicability of the Terzaghi Theory of Consolidation and to determine the compressibility of silt soils with varying clay content. A pure silt was extracted from the Lebanon Silt Loam and mixed with varying amounts of the Onyx Cave Illite-Chlorite Clay. The compressibility of these mixtures was determined and an attempt made to apply the Terzaghi Theory in the analysis. It was found that the compressibility of soils high in silt content is very low. It was also found that the Terzaghi Theory may be applied to mixtures of 15 percent or more …

Construction Of A Laboratory Type, Convertible Excitation Argon Laser, Arthur P. Reckinger

Masters Theses

"The purpose of this thesis is to describe the construction of a general purpose, convertable [sic] excitation, laboratory type, argon laser. Quartz tubing was used in the final model while attempts to use alumina were made during earlier work. The final model has total optical power output of 230 mw at a discharge current of 29 amperes in the dc excitation mode. Provision was also made to utilize RF or pulsed excitation. The device is built so that several values of optical transmittance are available with a wide range of mirror placement"--Abstract, page ii.

Effects Of Mixing Procedure Upon Uniformity Of Fibre Reinforced Concrete, Donald E. Nortrup

Masters Theses

"This thesis describes the effects of several methods of introducing wire fibres into a concrete mix upon the uniformity of wire fibre reinforced concrete. Various mechanical and manual methods of introducing the fibres were used and comparisons of the methods were based upon variability in splitting tensile strength and the quantitative distribution of the fibres as determined by visual inspection of sawed cylinders. Test results show that the tensile strength of concrete is increased appreciably by the inclusion of steel wire fibres in the mix and the uniformity of strength is similar to that of unreinforced concrete. The methods of …

Continuous Countercurrent Evaporation Through Porous Water-Repellent Membrane With Pressure Above Atmospheric, Yung C. Hsu

Masters Theses

"An experimental method for measuring mass transfer rates at pressures above atmospheric has been developed for the case of continuous countercurrent evaporation through porous water-repellent membranes. The final developed equipment is suitable for operation under pressures up to 50 psig and at temperatures near the boiling point of 7% salt water when high flow rates are reached. Rates of evaporation of water through the membrane were measured, and the data and results were used to examine the effects of operating conditions on the over-all mass transfer resistance. Least squares equations for fitting the data were also obtained. Over-all mass transfer …

A Programmed Synthesis Procedure For Asynchronous Sequential Circuits, Robert Judson Smith

Masters Theses

"The synthesis procedure for large asynchronous normal fundamental-mode sequential circuits is time-consuming and tedious when performed manually. This paper describes a series of computer programs which, given a machine specification in flow table form, automatically produces simplified normal form implementation design equations. The user may specify that either minimum-variable state assignments, or more rapidly generated near-minimum-variable codes be found. Next-state equations are formed using the generated state assignments and converted to simplified sums of products. Sample machines having flow tables of up to eighteen rows by four columns are synthesized"--Abstract, page ii.

A Transmission Electron Microscopy Study Of Some High Strength Plain Carbon Steels, George Joseph Vytanovych

Masters Theses

"Methods of preparing foils of high strength, heat treated, plain carbon steels for examination in the electron microscope by the transmission technique were perfected and are described. Two processes for the initial thinning of a bulk sample were successful. A chemical process was found to be more rapid but not satisfactory for small samples. A mechanical process was slower, but was applicable to the smaller specimens. Electro-polishing the thinned material yielded acceptable foils from which photomicrographs of good quality were obtained. The microstructure of the high strength steel samples showed typical tempered martensite. No reasons for the differences in ductility …

Minimization And Generation Of Next-State Expressions For Asynchronous Sequential Circuits, Gary Keith Maki

Masters Theses

"One step in the synthesis procedure for realizing an asynchronous sequential circuit that is operating in fundamental mode is to obtain an internal-state assignment that will realize the operations of the circuit. Often the procedures that are used in accomplishing the above task generate several satisfactory assignments. The first part of this paper presents a method that will enable one to predict which of the internal-state assignments will yield a simpler set of next-state expressions. A second topic treated in this paper is one of presenting a method to generate the next-state expressions for an asynchronous sequential circuit directly from …

The Effect Of Concentration On The Viscosity Of Dilute And Moderately Concentrated Polymer Solutions, Hwa Luh

Masters Theses

"The effect of concentration on the viscosity of dilute and moderately concentrated polymer solutions was studied for eight narrow molecular weight polystyrene samples (900

Scanning Properties Of Unsymmetrically Loaded Aperture Arrays, Gary Dean Brunner

Masters Theses

"Radiation patterns resulting from an array of waveguide-fed apertures, filled with assymmetrically [sic] cut dielectric inserts, in an infinite ground plane were investigated. The results of Blumberg and Hemmen concerning single apertures were applied to a two-aperture array, with emphasis upon obtaining an array capable of scanning in the far field through changes in the permittivity of the assymmetrically [sic] cut dielectric inserts. Scanning was shown to be possible with up to a 60⁰ scan angle with a "push-pull" method of varying permittivities, in which the permittivity of one insert is raised while the other is lowered. The aperture field …

Annealing Characteristics Of Neutron Irradiated Silicon Transistors, Joseph Robert Chott

Masters Theses

"When a transistor is subjected to neutron irradiation, a component of base current proportional to neutron fluence is induced. From the effects of annealing on the base and collector currents, the conclusion was drawn that there is an apparent difference in the annealing characteristics between the neutral and the space-charge regions of the semiconductor device. This study of the anomalous annealing indicates that the neutron-induced component of base current is a result of one, or a combination, of the following mechanisms: a quasi-tunneling recombination phenomena in the emitter-base space-charge region, or an influence of the p-n junction electric field on …

The Measurement Of Explosively Induced Stresses In Rock-Like Materials With A Capacitive Transducer, Vincent Paul Crane

Masters Theses

"A capacitive transducer was developed for measuring the free surface motion in Hydrostone blocks loaded by an explosive plane wave generator approximately one foot from the specimen. The charge to specimen distance was adjusted to produce a single spall, the position of the fracture being noted on the recovered specimen. The longitudinal wave velocity in each specimen was determined by the ultrasonic pulse technique before each shot. From the above measurements the stress, strain and strain rate at the point of fracture were determined. An attempt was made to determine the actual fracture time with imbedded [sic] conductive graphite rods, …

Lattice Constants, Thermal Expansion Coefficients, Densities, And Imperfections In Gold And The Alpha-Phase Of The Gold-Indium System, Vinayak Keshavlal Patel

Masters Theses

"An investigation of structure insensitive properties (lattice parameters, thermal expansion coefficients, densities, and imperfection) of gold and the alpha-phase of the gold-indium system was made. The gold-indium alloys were prepared from high purity (99.999%) gold and indium by melting both metals inside sealed quartz glass tubes which were first evacuated and then filled with helium gas. The solidified alloys were annealed and then examined by x-ray for homogeneity. The lattice constant of 99.999% pure gold at 25⁰C was found to be 4.07894 ł 0.00005 (corrected for refraction) Å. The coefficient of thermal expansion was 13.4 x 10⁻⁶⁰C⁻¹ between 15 and …

An Investigation Of The Effects Of An Impact On Some Of The Mechanical Properties Of Aluminum Alloy 2014-T6, Rajnikant K. Shah

Masters Theses

"Static and impact tests were conducted on an Aluminum alloy 2014-T6 specimen. The purpose of this research was to determine the effects of an impact load on some of the mechanical properties of aluminum. The cross section of the specimen measured 4.438 in. by 3.850 in. and it was 12 in. long. It was equipped with a total of four electric resistance gages connected in two pairs. One pair measured longitudinal strain while the other measured transverse strain. Both gages in each pair were mounted on the opposite sides to cancel the bending effect. In the static tests, load was …

Quality Of Surface And Subsurface Water In A Missouri Carbonate Karst Terrain (Dry Fork, Norman, And Benton Creek Watersheds), James Chi Huang

Masters Theses

"Little is known about the effect of carbonate karst terrain on water quality in the United States. Karst topography occurs over a large portion of Missouri and over a significant part of other midwestern states. The objectives of this study were the determination of the quality of surface and subsurface water in carbonate karst terrain and the investigation and evaluation of the effect of rainfall and runoff on water quality in the Meramec Spring area, east of Rolla, Missouri, during both the dry and wet seasons over the period of one year. Water samples were collected at a large number …

Analog Simulation Of A Plug Flow Tubular Reactor, Jon Douglas Carson

Masters Theses

"This thesis stresses the importance of analog and digital computers in the field of reaction kinetics. The analog computer is used to simulate a chemical reaction, the hydrolysis of acetic anhydride. The hydrolysis reaction takes place in a tubular reactor. The reactor is 3/4 inch in diameter and 20 feet long. These reactor dimensions allow the reaction system to approach plug flow, if the reactants flow through the reactor at turbulent flow rates. The physical, reactor, system is used to obtain experimental data for the hydrolysis reaction. The data is obtained at reactor temperatures between 75 and 100°F. Feed concentrations …

Velocity Profiles In Viscoelastic Drag Reducing Solutions, Luis Gustavo Florez E.

Masters Theses

"Turbulent velocity profiles in viscoelastic drag reducing solutions were measured using hot-film anemometer and Pitot tube techniques. Data were obtained in a solution of one per cent aluminium [sic] dioleate in toluene and in 0.2 and 0.4 per cent solutions of polyisobutylene (PIB) L-200 in cyclohexane. Velocity profiles were also obtained for comparison in toluene and cyclohexane by both techniques. By integrating the Pitot tube velocity profiles, large flow rate discrepancies between integrated and measured flow rates were found for the drag reducing polymer and soap solutions. This discrepancy was not observed in the hot-film anemometer measurements. The hot-film anemometer …

The Economics And Design Of Desalination By Evaporation Through Porous, Water-Repellent Membranes, Kuei-Hsiung Yang

Masters Theses

"The economics of desalination by evaporation through porous, water-repellent membranes has been studied in this investigation. Using reasonable assumptions this desalination process was found to be economical with the principal advantage being the simplification of multi-stage flash-type evaporation. Based on this process, two different methods were designed and studied by means of computer calculations for a 10 million gallons product water per stream day desalting plant. One method was based on a membrane evaporator and a heat exchanger and was designated Method I; and a combined evaporation-heat exchanger system was designated at Method II. The major factors affecting the economics …

Fault Detection In Combinational Networks, Alexander Rahm

Masters Theses

"This paper presents an algorithm for locating a failure in combinational logic networks, which is a problem of importance in the maintenance of computer systems. The procedure is based on the "path sensitizing" idea for fault detection. The networks considered are non-redundant, consisting of AND, OR, and NOT elements. The class of faults investigated is that which causes a connection to appear to be logically suck-at-one or stuck-at-zero, and only single failures are treated. It is shown that the failure is generally located to a specific "fault group"--Abstract, page 2.

Programmed State Assignment Algorithms For Asynchronous Sequential Machines., Wayne L. Schoeffel

Masters Theses

"An important step in the synthesis procedure for realizing a normal fundamental mode asynchronous sequential circuit is the internal state assignment. Although systematic methods have been developed to construct minimum-transition-time state assignments, they become long and tedious with hand methods for machines with more than 7 or 8 internal states. To extend the application of these algorithms to larger problems, this paper presents an efficient digital computer program for generating minimum-variable state assignments. An alternate program is also presented which, though shorter, does not guarantee a minimum-variable assignment"--Abstract, page ii.

The Relation Of Heat Transfer To Mass Transfer In Vaporization Through Porous Membranes., Chung-Liang Yeh

Masters Theses

"The object of this investigation was to study the mass and heat transport phenomena through porous, water-repellent membranes. The investigation concerned the rate of vaporization of salt water at a porous membrane surface, mass transfer of vapor through the pores of the membrane, condensation of vapor on the other surface of the membrane in contact with a coolant (fresh water), and the undesired heat transfer by conduction through the membrane. The water-repellent membrane separated the two liquid phases by surface tension forces and provided a vapor phase in its pores. Membranes made of fiberglass and Teflon had been found suitable …

Negative Resistance In Cadmium Sulfide., John William Mohr

Masters Theses

"A light-sensitive, negative-resistance phenomenon has been observed in a special two-terminal CdS device fabricated from selected single crystals. The device differs from those used in previous investigations in that one end of the device was masked to keep out visible light and that the phenomenon was observed at room temperature. A method is described which enables the phenomenon to be observed on a reproducible basis. It was found that the CdS single crystal must have a relatively high density of traps. Possible mechanisms which may contribute to the phenomenon are discussed"--Abstract, page ii.

Film Boiling From Horizontal Plates With Low Thermal Capacity, K. M. Ragsdell

Masters Theses

"The object of this investigation was to obtain data for saturated film pool boiling from a low thermal capacity flat plate at atmospheric pressure. A test plate, constructed from resistance strip, was placed horizontally in a pool of liquid, and was heated electrically. Refrigerant-11 and nitrogen were used as the boiling liquids. Heat transfer results were obtained in both fluids over a temperature range of approximately 1200F⁰ (400-1600⁰F). Surface size, roughness and orientation effects were observed for flat horizontal heated surfaces with one dimension near the most dangerous wavelength. No surface material effect was observed. Excellent correlation of the data …