Engineering Commons^™

An Investigation Of Turbulent Taylor-Couette Flow Using Laser Doppler Velocimetry In A Refractive Index Matched Facility, Joseph C. Parker

Masters Theses

Turbulent Taylor-Couette flow between an annulus formed by two concentric cylinders with dead end walls is comprised of complex patterns of vortices. An experimental apparatus was designed to provide refractive index matching between the annulus and working fluid. Optical access was maintained through three sides of the annulus and one end wall. An aqueous solution of sodium iodide was formulated to match the refractive index of the Plexiglas annulus. Laser Doppler Velocimetry was used to measure the three components of velocity and turbulence intensity throughout a planar section in the annulus. The annulus dimensions were: ƞ= 0.672, d = 15.08 …

A Study On The Causes Of Variations In Transmissivity And Storativity During Pump Tests At Asylum Lake, Paul Joseph Pare

Masters Theses

Over a two year period, Western Michigan University ran a number of pump tests in the Asylum Lake Area in Kalamazoo, Michigan. The transmissivities and storativities calculated from these tests differed significantly from well to well in any particular test, and from pump test to pump test. Utilizing the computer programs AQTESOLV 3.0 and Aquifer Parameter Estimator, a number of T and S values were calculated. After analysis of the results, the following conclusion was drawn. The main reason for the deviations in the T and S values arose from the mixing of the results of numerous methods (some of …

Dynamic Pulse Buckling Of Columns With Viscous Damping, Murli Kadandale

Masters Theses

This is a study of dynamic pulse buckling of columns with viscous damping. The differential equations of motion were obtained using the Bemoulli-Navier hypothesis. The effects of axial and rotary inertia were included in the analysis. The Voigt-Kelvin model for a viscoelastic material is used. The Finite Difference Method was employed to solve the differential equations of motion. First columns without geometrical imperfections were studied, and a correlation between the damping modulus and the more familiar damping ratio was obtained. Then beams with initial geometrical imperfection were studied. A suitable dynamic buckling criterion was defined. It was observed that viscous …

The Effect Of Rotor Wake/Exit Guide Vane Interaction On The Total Pressure Losses In An Airfoil Cascade, Aaron Mosebach

Masters Theses

Computational simulations have been performed to study the effects of unsteady rotor wakes on the total pressure losses and the boundary layer characteristics in a compressor cascade. In the numerical simulations, transitional and turbulent flow conditions were modeled at design and off-design inlet flow angles, and for varying rotor wake widths and wake velocity deficits.

First, simulations were performed in the absence of rotor wakes at the inlet of the EGV (Exit Guide Vane) cascade. Second, simulations were performed for different wake width and wake velocity deficit values at the inlet of the EGV cascade. The majority of the numerical …

Cumulative Average Pricing Method For Estimating Average Service Life, Mahendra Babu Hosangadi

Masters Theses

The study determined if accuracy of estimation of retirement price of industrial equipment was affected by using a cumulative average pricing (CAP) method at varying conditions of inflation rate, service life, and life characteristics. The study also determined the accuracy of estimating the average life of unaged data by simulated plant record (SPR) method. Thirty-six experiments were conducted at varying conditions of inflation rate, curve type and average life. The study was conducted for two left modal curves, two symmetrical modal curves and two right modal curves at 20 and 40 years average life using three different inflation rates: 3%, …

Addition Of Automatic Dimensioning Feature To D-M-E’S Ultimate Mold Base Design Software, Cori L. Brown

Masters Theses

There have been many improvements in the plastics industry over the past few years. One of these areas is in the design of injection molds. This area has been enhanced by the use of Computer-Aided Design systems and furthered by the creation of specialized mold design software. The Ultimate^® design system from D-M-E has made a mold designer's job much easier by automating much of this process. This project extends the function of this software by adding an automatic dimensioning feature that will make the mold design process less tedious and less time consuming. This addition will also standardize …

Development Of A Mold Trial Procedure For Establishing A Robust Process, Marc R. Vander Kooi

Masters Theses

To reduce variation in the injection molding process it is essential to understand the effect of process, mold, and material variables on critical part characteristics. Gaining a thorough understanding of these variables is often difficult due to the limited time manufacturers typically have available for mold trials. To address this issue, the Premier Class Injection Molding consortium (PCIM) has performed numerous experiments relating to shot-to-shot repeatability. Using the PCIM data set and experimentation procedures as a base, a procedure was developed to collect data during a mold trial. Incorporating small experiments and statistical analysis, the new procedure allows meaningful data …

Modeling And Development Of A Cellular Micro-Kernel, K. Balaji

Masters Theses

A novel cellular load distribution strategy was designed and implemented on transputers by Dr. Richard Taylor and Dr. Don Goodeve at the University of York, United Kingdom. Based upon the above proposed strategy, a statistical model was developed using the Cellular Automata Theory. The theoretical model drives the implementation process of the cellular micro-kernel on the nCUBE 2S system. The load distribution and the performance characteristics for snake and L type transmission modes, and for uniform and non-uniform distribution of destination processors of the micro-kernel has been measured and compared with our theoretical model. The results show good agreement between …

A Comparative Study Of The Stress Concentration Factors Arising Between Two Equal, Nearly Intersecting, Perpendicular, Pressurized Holes In An Infinite Solid With Those Arising Due To An Infinite Series Of Such Holes, Paul J. Drogowski

Masters Theses

Finite element analysis is used to determine the stress concentration factors arising from two equal, perpendicular, nearly intersecting, pressurized holes in an infinite solid while varying the distance and pressure ratios between the holes. The results are compared and contrasted with those previously obtained for an infinite series of such holes. A ratio of the distance between the holes to the diameter of the holes at which the holes can be considered to be single holes in an infinite solid is determined. A study is performed to determine a correlation between the location of the region of maximum stress and …

Hardware/Software Codesign And Simulation With The Occam Programming Language, Roy L. Krans

Masters Theses

Hardware/software codesign is an increasingly popular method for improving system performance and adaptability while minimizing cost. The goal of this design approach is to achieve the desired system characteristics (performance, fault tolerance, cost, power consumption, etc.) by carefully distributing the system functions among hardware and software components. Popular tools for describing this dual hardware/software functionality are behavioral languages such as C++ and Ada. These languages typically include facilities for both traditional sequential programming as well as behavioral modeling.

This thesis examines the effectiveness of occam as a behavioral language and its role in hardware/software codesign. The occam language is used …

Thermoplastic Composites Of Recycled High Density Polyethylene And Recycled Tire Particles, James N. Mckirahan Jr.

Masters Theses

This study identified the mechanical properties and processibility of composite materials of recycled high density polyethylene (HDPE), recycled rubber tire particles, and/or ethyl co-vinyl acetate and poly (e-caprolactone). The composites were processed using a single screw extrusion system.

Three groups of experiments were conducted, on the composites in their extruded form to investigate the mechanical properties of ultimate tensile strength, percent elongation, and hardness. The first experiment investigated the effect of recycled rubber particle concentration in the composites up to 25 percent. The second experiment investigated the effect of recycled rubber particle size on the composites of recycled HDPE and …

Iron Phosphate Glasses As A Potential Nuclear Waste Disposal Medium, Melissa G. Mesko

Masters Theses

”Phosphate glasses containing large amounts of Fe₂O₃ (up to 43wt%) were studied to determine their potential suitability as nuclear waste disposal glasses for high level radioactive wastes containing large concentrations of iron oxide, phosphate, and fluoride compounds. Glass formation and chemical durability was the prime focus of this study, while properties such as density, thermal expansion, dilatometric softening temperature, and devitrification temperature were examined as well. It was found that large amounts of simulated nuclear waste material (up to 44.4wt% Cs₂O or 37.5wt% SrO) could be incorporated into the base iron phosphate glass while retaining …

Effects Of Specimen Size Reduction On The Transition Curve Of The Charpy V-Notch Impact Test, Lonnie Eugene Schubert

Masters Theses

"This study was undertaken to correlate the impact properties of ASTM standard full size Charpy V-notch impact specimens to the impact properties of subsize specimens. An ASTM A533-B quenched and tempered plate steel was examined. The fine grained martensitic material had a coarse prior austenite grain size, which resulted in a low upper shelf energy for this material. Three sizes of specimens were included. Specimens were irradiated in the TRIGA Reactor Facility operated by the U. S. Geological Survey in Denver, Colorado, to 1 x 10¹⁹ n/cm² (E > 1 MeV) at 150°C (302°F). Unirradiated and irradiated specimens were …

Eigenproperties Of Nonclassically Damped Dynamic Systems, Daniel Patrick Malone

Masters Theses

"This thesis develops perturbation series solutions for the eigenvalues and eigenvectors of nonclassically damped dynamic systems for the case where the unperturbed system has repeated eigenvalues. The case of repeated eigenvalues is much more complicated than the case of perturbing a system with distinct eigenvalues. Because of this difficulty, only a specific category of dynamic systems with repeated eigenvalues is addressed. Namely, only those systems that when perturbed have series solutions of the form of a power series. This category of systems can be easily identified by an a priori check developed in the application section of this thesis. The …

A Neural Network Thrust Force Controller To Minimize Delamination During Drilling In Graphite Epoxy Laminates, Robert B. Stone

Masters Theses

"Delamination is a well-recognized problem associated with drilling in fiber-reinforced composite materials (FRCM). The most noted problems occur as the drill enters and exits the FRCM. Since drilling is often a final operation during assembly, any defects introduced in parts by drilling represent an expensive loss. Studies based on linear elastic fracture mechanics theory have proposed critical thrust forces in the various drilling regions that will prevent crack growth or delamination. Using these critical thrust force curves as a guide, a thrust force controller was developed to minimize the delamination while drilling in graphite epoxy laminates. A neural network control …

Nonlinear Finite Element Micromechanic Analysis Of Thermoplastic Composite Of Recycled High Density Polyethylene Reinforced With Short Glass Fibers, Qiming Lou

Masters Theses

This thesis studied the nonlinear micromechanic behavior of thermoplastic composite of recycled high density polyethylene (HDPE) reinforced with short glass fibers using finite element method. The composite material was modeled using a micromechanic unit cell to simulate the stress distribution between the plastic matrix and the fiber in the composite. Nonlinear behavior of recycled HDPE and imperfect bonding between the fiber and matrix were investigated. Load-bearing capability of the fiber was evaluated using stress partition ratio (SPR) in the composite models. The effect of fiber aspect ratio on the stress distribution of the composite was studied to optimize the material …

An Evolutionary Approach To Allocating Tasks In Hard Real-Time Distributed Systems, Christian Lang

Masters Theses

In real-time systems, correctness not only depends on the result of the computation but also on the time at which this result is available. The violation of timing constraints in hard real-time systems can be critical to human life or environment. Therefore, the scheduling algorithm for distributed systems has to allocate tasks to processing nodes so that no timing constraints can be violated. In addition to timing constraints, tasks have precedence and fault-tolerance constraints.

Static scheduling allocates tasks to processing nodes before the tasks are executed. Static scheduling problems are known to be NP-hard [4]. Therefore, heuristic techniques are necessary …

An Investigation And Improvement Of Electrorheological (Er) Fluid Technology, Adil F. Dalal

Masters Theses

The purpose of this research was to investigate and overcome the limitations of Electrorheological (ER) fluids and to introduce this advanced technology at WMU. Electrorheological (ER) Fluids are a special class of fluids, which exhibit a reversible, infinitely variable phase transition from a liquid to a solid/semi-plastic state, in the presence of an electric field.

ER fluids can provide a unique solution to the problems of vibration isolation of systems. The applications are currently limited due to the high voltage requirements, electric power related heating and limited research into wear/abrasive characteristics of ER fluids.

A specially designed and constructed "electro-viscosimeter" …

A Heuristic Procedure For Designing A Cellular Manufacturing System While Minimizing Makespan, Panduranga Badam

Masters Theses

This study is the first of its kind in Group Technology (GT) literature and successfully demonstrates the application of the simulation technique to analyze different alternatives for machine and part grouping problem.

This study considers several aspects such as processing time, sequence of operations, alternative routing, setup time and dynamic shop condition for machine-part grouping. The heuristic developed aims to reduce intercellular moves, setup time and makespan time of parts. It also enables the decision markers to evaluate performance measures and to choose the best alternative at every step of the machine grouping process. Two examples have been used to …

The Effects Of Non-Uniform Blade Geometries On Cascade And Turbine Stage Performance, Hiroyuki Maeda

Masters Theses

It is known that in-service turbomachinery blades do not have uniform shapes. There are small differences due to blade erosion, manufacturing tolerances, or faulty installation. These differences can be in the size, shape, or relative angles of the blade. In an effort to predict losses resulting from changes in blade thickness and/or blade angles, a two-part investigation has been conducted. A two-dimensional unsteady Navier-Stokes flow analysis has been used to perform numerical experiments.

First, simulations were performed for an isolated cascade. One of the two stators was scaled and/or rotated. Results of the numerical simulations show that increasing the blade …

Effect Of Poly Acrylate Addition On Coating Color Rheology, Water Retention And Coating Performance, Shambhu Nath

Masters Theses

Five polyacrylate samples were used to study their effects on coating color rheology, water holding and runnability. The Cylindrical Laboratory Coater was used to apply the coatings and study the runnability of the coating colors. The healing tendencies of the coatings were studied by inducing a scratch under the blade. The higher acid level and degree of crosslinking of the polyacrylate gave higher viscosity and the higher acid level also gave higher water retention. Coating colors containing polyacrylates were less prone to dilatancy at high shear. The addition of polyacrylate reduced the healing of coating colors, but for the same …

Rear Seat Belt Usage And Comfort, Kuntal Thakurta

Masters Theses

Seat belts have been shown to be effective in reducing car crash fatalities and injuries. Despite consistent evidence that seat belts when worn can provide the greatest vehicle occupant protection of all currently available occupant restraint systems, seat belt use rates remain low. The rates of occupants wearing seat belts in rear seats is much lower than front seat occupants. One of the primary causes for occupants not using seat belts in rear seats has been lack of comfort. The purpose of this thesis was to study the relationship of comfort and seat belt use in rear seats. The current …

Recent Advances In Engineering Design: Theory And Practice, Andrew J. Moskalik

Masters Theses

In the last few years, industry and academia have focused greater attention on the area o f engineering design. Manufacturers have implemented new design methods such as concurrent engineering and design for manufacture, and academia has increased research in design-related issues. This paper will attempt to summarize the recent advances, both scholarly and industrial, relating to the field of design. I will examine new methodologies and supporting tools for the design process, both in use and under research. This paper will cover concurrent engineering, design for manufacture, quality methods, design theory research, computer-aided design, expert systems, analysis programs, manufacturing, and …

An Empirical Study Of Just-In-Time And Total Quality Management Principles Implementation In Manufacturing Firms In The U.S., Loknath Sriparavastu

Masters Theses

Literature in vogue points out that, in the last decade, American manufacturing companies came a long way in their renewed emphasis on the quality process. Justin- Time (JIT) and Total Quality Management (TQM) are the two magical phrases that are being frequently used in almost all the articles published on quality and productivity. Nevertheless, the literature does not provide any satisfactory explanation as to how JIT and TQM principles are implemented in the manufacturing industries.

This research, through a nationwide empirical survey, analyzed the effects of JIT and TQM strategies implementation. Survey results showed that implementing both JIT and TQM …

An Empirical Investigation Of Total Quality Management (Tqm) Effectiveness In Healthcare Organizations, Lokesh S. Basappa

Masters Theses

American hospitals are implementing quality programs to offer higher quality service at reduced cost. However, the results of these programs in many hospitals have often not met expectations.

This research analyzed the effectiveness of Total Quality Management (TQM). The objective of the study was to better understand how TQM strategies can best be applied by hospitals. An empirical survey was distributed to Michigan hospitals and an analysis was performed to meet this objective.

The survey results show that hospitals involved indirectly with quality programs haven't realized that they are implementing TQM strategies. On the other hand some hospitals say that …

A State Architecture Notation Specification Of The Electronic Industries Association Rs-232-C Generic Interchange Circuit, Nelson E. Hastings

Masters Theses

The Electronic Industries Association (BIA) RS-232-C recommendation is an interface specification which was introduced in August 1969 and presents a natural language specification of a 25 pin binary serial data interface between a Data Communication Equipment (DCE) and a Data Terminal Equipment (DTE). The exchange of data signals between a DCE and a DTE ultimately provides the means for DTEs to communicate on networks of DCEs interconnected by different transmission mediums possibly over great distances. The exchange of data signals between a DCE and a DTE occurs at an interface via interchange circuits.

In this thesis we will create a …

Internal Acoustic Excitation Of An Airfoil Surface For Drag Reduction, Wendy L. Holforty

Masters Theses

This research investigated the effects of internal acoustic excitation on the boundary layer and surface of an airfoil. A NACA 16- 018 symmetric airfoil was tested in the Western Michigan University wind tunnel. The shedding vortex frequency of the airfoil was determined using hot-film anemometry. Using stroboscopic and holographic interferometry, the natural frequencies of the airfoil surface were determined. The airfoil surface was tuned such that the frequency of the shedding vortex is a resonant frequency and two internally mounted acoustic drivers were used to excite the surface of the airfoil at the shedding vortex frequency. The effects on pressure …

An Ergonomics Approach To Evaluate The Use Of Two Different Fixtures For Upholstering, Maria Luisa Roa

Masters Theses

A furniture company in West Michigan proposed an evaluation of a new fixture that will be used in a repetitive manual stapling operation.

Numerous studies reveal that activities involving repetitive wrist motions cause inflammation in the median nerve that runs through the structure of the carpal wrist, causing a cumulative disorder known as Carpal Tunnel Syndrome (CTS). This syndrome is one of the most prevalent in industrial settings and service companies.

This study investigated if the use of a new design of a fixture had an impact on operators' performances. Three-dimensional comparative analysis was used to observe operators' wrist angular …

Information Processing Using Laser Speckle, Rathnakar Gopisetty

Masters Theses

"The random speckle intensity pattern, which is produced by the scattered optical field from a rough surface when illuminated, can be used as a carrier of information. A theoretical study is performed to use the speckle patterns for retrieving the information of various kinds of object motions. A mathematical model of speckle is developed and used to relate different speckle patterns at various intervals as the object is experiencing motion. Four different object motions, i.e., one dimensional perpendicular motion, axial motion, three-dimensional motion, and rotational motion of an object are analyzed. In each case an interference pattern is produced which …

Adaptive Critic Based Neural Networks For Control, Victor Biega

Masters Theses

"Dynamic Programming is an exact method of determining optimal control for a discretized system. Unfortunately, for nonlinear systems the computations necessary with this method become prohibitive.

This project investigates the use of adaptive neural networks that utilize dynamic programming methodology to develop near optimal control laws. First, a one dimensional infinite horizon problem is examined. The first part of this thesis considers problems involving cost functions with final state constraints for one dimensional linear and nonlinear systems. It also investigates a two dimensional linear problem. In addition to these examples, an example of the corrective capabilities of critics is shown. …