Enhancing Progressive Collapse Resistance Of Steel Building Frames Using Thin Infill Steel Panels, Victor M. Sanchez Escalera

Master's Theses

Progressive collapse occurs when damage from a localized first failure spreads in a domino effect manner resulting in a total damage disproportionate to the initial failure.  Recent building failures (e.g., World Trade Center twin towers) highlight the catastrophic outcome of progressive collapse.  This research proposes a reliable and realistic retrofit technology which installs thin steel panels into steel building structural frames to enhance the system progressive collapse resistance.

The steel frames with simple beam-to-column connections, under different boundary conditions (i.e., sidesway uninhibited and sidesway inhibited, respectively), and the loss of one bottom story column were retrofitted using the proposed technology …

Simulation And Validation Of Two-Component Flow In A Void Recirculation System, Oscar Eduardo Daza

Master's Theses

Nuclear power plants rely on the Emergency Core Cooling System (ECCS) to cool down the reactor core in case of an accident. Occasionally, air is entrained into the suction piping of ECCS causing voids that decrease pumping efficiency, and consequently damage the pumps. In an attempt to minimize the amount of voids entering the suction side of the pump in ECCS, a Void Recirculation System (VRS) experiment was conducted for a proof of concept purpose. While many studies have been oriented in studying two-component flow behavior in ECCS, none of them propose a solution to minimize air entrainment. As a …

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Investigation Of A Simulated Annealing Cooling Schedule Used To Optimize The Estimation Of The Fiber Diameter Distribution In A Peripheral Nerve Trunk, Arya Vigeh

Master's Theses

In previous studies it was determined that the fiber diameter distribution in a peripheral nerve could be estimated by a simulation technique known as group delay. These results could be further improved using a combinatorial optimization algorithm called simulated annealing. This paper explores the structure and behavior of simulated annealing for the application of optimizing the group delay estimated fiber diameter distribution. Specifically, a set of parameters known as the cooling schedule is investigated to determine its effectiveness in the optimization process.

Simulated annealing is a technique for finding the global minimum (or maximum) of a cost function which may …

Semiconductor Laser Device-Level Characteristics, Clement K. Law

Master's Theses

High-speed modulations of the semiconductor lasers are highly desirable in cost-effective optical communication systems.  Developing the experimental setups to extract the characteristics of the semiconductor lasers is vital to the future of the optical research projects.  In this thesis, integrated experimental setup designs have been developed to measure the characteristics of the Vertical Cavity Surface Emitting Laser (VCSEL), Distributed Feedback (DFB), and Fabry-Pérot (FP) lasers.  The measurements of the DC characteristics are optical power versus drive current (L-I) curves (DFB, VCSEL) and optical spectra (FP, DFB, VCSEL).  In addition, the high-speed optical detection measurement of the optoelectronic frequency responses for …

A Computational Study Of Engine Deflection Using A Circulation Control Wing, Bryan Holly Blessing

Master's Theses

In the past, research into Short Takeoff and Landing aircraft has led to the investigation of the coupling of a Circulation Control Wing and Upper Surface Blowing engine. The Circulation Control Wing entrains the flow of the engine to be deflected downward such that a component of the thrust is now in the vertical direction. The unfortunate consequence of the Upper Surface Blowing engine is the poor cruise performance due to scrub drag. Cal Poly's research into a Cruise Efficient Short Takeoff and Landing Aircraft offers a solution by pylon mounting over the wing engines. Analysis shows that the engine …

High-Frame-Rate Oil Film Interferometry, Jonathan Charles White

Master's Theses

High-Frame-Rate Oil Film Interferometry

Jonathan Charles White

This thesis presents the design and implementation of a high-frame-rate oil film interferometry technique (HOFI) used to directly measure skin friction in time dependent flows. Experiments were performed to determine the ability of a high-speed camera to capture oil film interferometry images. HOFI was found to be able to capture these interferometry images at frequencies up to 10⁵ Hz. Steady laminar and turbulent flows were tested. Transient flows tested consisted of a wind tunnel ramping up in velocity and a laminar boundary layer which was intermittently tripped to turbulence by puffing air …

Design And Development Of Two Test Fixtures To Test The Longitudinal And Transverse Tensile Properties Of Small Diameter Tubular Polymers, Carolyn Berry

Master's Theses

Hundreds of thousands of vascular bypass grafts are implanted in the United States every year, but there has yet to be an ideal graft material to substitute for one’s own autologous vessel. Many synthetic materials have been shown to be successful vessel replacements; however, none have been proven to exhibit the same mechanical properties as native vessels, one of the most important criteria in selecting a vascular graft material. Part of this issue is due to the fact that, currently, there is no “gold standard” for testing the longitudinal and transverse tensile properties of small diameter tubular materials. While there …

Geomagnetic Compensation For Low-Cost Crash Avoidance Project, John C. Torres

Master's Theses

The goal of this work was to compensate for the effects of the Earth’s magnetic field in a vector field magnetic sensor.  The magnetic sensor is a part of a low-cost crash avoidance system by Stephane Roussel where the magnetic sensor was used to detect cars passing when it was mounted to a test vehicle.  However, the magnetic sensor’s output voltage varied when it changed orientation with respect to the Earth’s magnetic field.  This limited the previous work to only analyze detection rates when the test vehicle travelled a single heading.  Since one of the goals of this system is …

Design And Analysis Of A Wind Energy Harvesting Circuit Using Piezoelectric Polymers, Jameson J. Thornton

Master's Theses

This thesis investigates a relatively new method for harvesting wind energy by using flexible piezoelectric polymers with additional sails to increase their ability to harvest wind energy. This paper also introduces a new topology deemed the “stacked buck” that allows for multiple inputs to a system with a single output. Derivations and analysis detail the workings of the “stacked buck” with a laboratory test to show a working model. This paper also reports another experiment done in a wind tunnel to analyze the capability of the piezoelectric polymers as sources to the “stacked buck” topology with measurements of the power …

Investigation Of The Behavior Of Free-Standing Gabions In Seismic Regions, Amy Ransom

Master's Theses

This thesis investigates the behavior of free-standing gabion walls in areas of mild seismicity. To investigate this behavior, three walls of varying internal cable patterns were constructed at a quarter-scale. These walls were tested with a mass shaker, and mode shapes, tone extractions, and damping ratios were calculated. A modal analysis was conducted using design spectra created from a suite of seven earthquakes from countries bordering Kenya. The corresponding lateral forces to these spectral displacements were found, and the restoring eccentricities from the soil restoring force were backed out through a summation of moments. All analysis was experimentally done due …

Exploring Trade-Offs In Auv Controller Design For Shark Tracking, Louis James Bertsch Iv

Master's Theses

This thesis explores the use of an Autonomous Underwater Vehicle (AUV) to track and pursue a tagged shark through the water. A controller was designed to take bearing and range to the shark tag and then control the AUV to pursue it.

First, the ability of a particle filter to provide an accurate estimation of the location of the shark relative to the AUV is explored. Second, the ability of the AUV to follow the shark's path through the water is shown. This ability allows for localized environmental sampling of the shark's preferred path. Third, various path weightings are used …

Asce 7–05 Design Rule For Relative Strength In A Tall Buckling-Restrained Braced Frame Dual System, Lisa J. Aukeman

Master's Theses

In mid- to high-rise structures, dual systems (DS) enable a structural designer to satisfy the stringent drift limitations of current codes without compromising ductility. Currently, ASCE 7-05 permits a variety of structural systems to be used in combination as a dual system yet the design requirements are limited to the following statement: Moment frames must be capable of resisting 25% of the seismic forces while the moment frames and braced frames or shear walls must be capable of resisting the entire seismic forces in proportion to their relative rigidities.

This thesis assesses the significance of the 25% design requirement for …

Optimization Of Point-Of-Use Water Treatment Device For Disaster Relief, Margaret June Herzog

Master's Theses

Point-of-use (POU) drinking water treatment is a common method of providing drinking water in disaster relief situations when critical water infrastructure is damaged. In these cases, POU treatment devices can be used to treat local water until relief organizations set up more permanent water provision methods. One such POU technology is PŪR^® Purifier of Water, a combined coagulation/flocculation and disinfection chemical treatment sachet produced by Procter & Gamble. PŪR^® has been shown to treat contaminated water to meet water quality standards and guidelines set by the U.S. EPA for water purifiers and by the World Health Organization and …

Water And Air Quality Performance Of A Reciprocating Biofilter Treating Dairy Wastewater, Seppi Matthew Henneman

Master's Theses

ABSTRACT

Water and Air Quality Performance of a Reciprocating

Biofilter Treating Dairy Wastewater

Seppi Matthew Henneman

Agricultural non-point source pollution is the leading water quality problem in surface water and the second leading problem in ground water in the US.  Among the contaminants, nutrients (such as nitrogen, phosphorus, potassium) can be transported from agricultural fields when cropland is not managed properly.  In California, dairy manure application to cropland has become tightly regulated with the goal of decreasing such nutrient pollution.  Dairies unable to balance their manure nutrient supply with cropland application area may benefit from a nitrogen removal technology.  One …

An Investigative Study Of Gurney Flaps On A Naca 0036 Airfoil, Gregory F. Altmann

Master's Theses

This project examined the effect of Gurney flaps on a 2D, 2-ft chord NACA 0036 airfoil in the Cal Poly 3’x4’ low speed wind tunnel at 25 m/s.  It also covered the numerical simulation of the experiment in computational fluid dynamics (CFD).  During the study, problems with the wind tunnel data were seen.  After a careful diagnosis, the problem was traced to dirty flow conditioners which were subsequently replaced.

Five Gurney flaps at 1, 2, 3, 4, and 5% of the chord were tested.  The Gurney flaps had the effect of eliminating the lift reversal effect and lowering the profile …

A Study Into The Use Of Microprocessor Relays For Motor Operated Valve (Mov) Electrical Protection In Nuclear Power Plants, James Andrew Tuccillo

Master's Theses

Motor Operated Valves (MOVs) are electro-mechanical components used to isolate, divert, or introduce fluid flow. The use of microprocessor relays for actuator motor electrical protection within nuclear power plants is the focus of this thesis and is implemented by providing a new and enhanced protection scheme that provides the adequate conservatism necessary to ensure valve operation while still maintaining electrical safety and continued operational availability. The comprehensive protection scheme is designed around an advanced microprocessor relay that has the ability to simulate the thermal overload conditions of a motor operating into a destructive thermal region. Through laboratory testing, the validity …

A Study Of Osteocyte Apoptosis By Region And Quadrant In Murine Cortical Bone, Jessica Kristen Chan

Master's Theses

ABSTRACT

A Study of Osteocyte Apoptosis by Region and Quadrant in Murine Cortical Bone

Jessica Kristen Chan

Osteocytes undergo apoptosis to spatially and temporally initiate bone remodeling.  This study investigates the distribution of apoptotic osteocytes within different quadrants and regions of cortical bone and compares the frequency of osteocyte apoptosis to regional factors associated with bone remodeling.  Specifically, the quantity of apoptosis was compared to levels of the bone morphagenic protein antagonists noggin and gremlin.  Samples of unloaded right tibial bone obtained from C57/Bl/6 mice underwent TUNEL staining for apoptotic osteocytes and were counterstained with methyl green to detect osteocyte …

Universal Engineering Programmer – An In-House Development Tool For Developing And Testing Implantable Medical Devices In St. Jude Medical, Khoa Tat Do

Master's Theses

During development and testing of the functionality of the pacemaker and defibrillator device, engineers in the St. Jude Medical Cardiac Rhythm Management Division use an in-house development tool called Universal Engineering Programmer (UEP) to ensure the device functions as expected, before it can be used to test on an animal or a human during the implantation process.  In addition, some applications of UEP are incorporated into the official releases of the device product.  UEP has been developed and used by engineers across departments in the St. Jude Medical Cardiac Rhythm Management Division (CRMD).  This thesis covers the flexible and reusable …

High-Resolution, Non-Contact Angular Measurement System For Psa/Rsa, Ronald D. Sloat

Master's Theses

A non-contact angular measurement system for Pitch Static Attitude (PSA) and Roll Static Attitude (RSA) of hard disk drive sliders is designed and built. Real-time sampling at over 15 KHz is achieved with accuracy of +/- 0.05 degrees over a range of approximately 2-3 degrees. Measuring the PSA and RSA is critical for hard drive manufacturers to control and improve the quality and reliability of hard drives. Although the hard drive industry is able to measure the PSA and RSA at the subassembly level at this time, there is no system available that is able to measure PSA/RSA at the …

Probabilistic Fault Displacement Hazard Analysis For Reverse Faults And Surface Rupture Scale Invariance, Zachary E. Ross

Master's Theses

p.p1 {margin: 0.0px 0.0px 0.0px 0.0px; font: 12.0px 'Times New Roman'}

A methodology is presented for evaluating the potential surface fault displacement on reverse faults in a probabilistic manner. This methodology follows the procedures put forth for Probabilistic Fault Displacement Hazard Analysis (PFDHA). Empirical probability distributions that are central to performing a PFDHA are derived from field investigations of reverse faulting events. Statistical analyses are used to test previously assumed properties of scale invariance with respect to magnitude for normalized displacement. It is found that normalized displacement is statistically invariant with respect to magnitude and focal mechanism, allowing for the …

Predicting Articular Cartilage Constituent Material Properties Following In Vitro Growth Using A Proteoglycan-Collagen Mixture Model, Michael Stender

Master's Theses

      A polyconvex continuum-level  proteoglycan Cauchy stress function was developed based on the continuum electromechanical Poisson-Boltzmann unit cell model for proteoglycan interactions. The resulting proteoglycan model was combined with a novel collagen fibril model and a ground substance matrix material to create a polyconvex constitutive finite element model of articular cartilage. The true collagen fibril modulus , and the ground substance matrix shear modulus , were varied to obtain the best fit to experimental tension, confined compression, and unconfined compression data for native explants and explants cultured in insulin-like growth factor-1 (IGF-1) and transforming growth factor-β1 (TGF-β1).  Results indicate …

The State Of Software Engineering Maturity And Licensure, Travis Lawrence Dean

Master's Theses

IEEE-CS is pursuing licensing for software engineers, but ACM believes that software engineering is too immature, and regulating the profession would be premature. In 1996, Norman Gibbs and Gary Ford from Carnegie Mellon University performed a qualitative survey of the maturity of the software engineering profession. I apply this model to the present state of the art in software engineering and analyze the results for 2010. I analyze the maturity of software engineering to determine that the profession is not yet ready for licensure. This is not because the infrastructure of software engineering is too immature, but because we have …

Mitigating Moisture Susceptibility In Hot-Mix Asphalt Concrete, Tom P. Nguyen

Master's Theses

Moisture damage in asphalt pavement has always been a problem for drivers, bicyclists, and pedestrians. The primary objective of this study is to evaluate moisture susceptibility of Hot-Mix Asphalt (HMA) and to investigate mitigation techniques using different antistripping agents. Three types of antistripping agents were used in this research investigation. Two of which are chemical based and the other is hydrated lime. The two types of liquid antistripping agents used in this study include Arr Maz CC LOF-6500 and Arr Maz CC XL-9000. These two liquid antistripping agents were tested at 0.25%, 0.50%, and 0.75%. Hydrated Lime was tested at …

Influence Of Nozzle Pressure, Standoff Distance, And Reinforcing Steel Cage On Water Jetting Of Cidh Pile Anomalies, Matthew Jason Schaffer

Master's Theses

The effectiveness of removing anomalous material from cast-in-drilled-hole (CIDH) piles by water jetting was examined.  The primary objectives of this research were to examine how reinforcing steel influences water jetting and to evaluate how jetting pressures and standoff distance from the material surface affect water jetting of concrete type materials and PVC tubing.  The experimental work consisted of water blasting submerged test specimens using rotary jets, nozzles, pumping equipment, and testing procedures currently used in construction practice.  The concrete test specimens were comprised of ring- and cylinder-shaped samples, containing materials with compressive strengths of approximately 160 and 3,600 psi.  Typical …

Tower-Tracking Heliostat Array, Joel T. Masters

Master's Theses

This thesis presents a method of tracking and correcting for the swaying of a central receiver tower in concentrated solar production plants.  The method uses a camera with image processing algorithms to detect movement of the center of the tower.  A prototype was constructed utilizing a CMOS camera connected to a microcontroller to control the movements of three surrounding heliostats.  The prototype uses blob-tracking algorithms to detect and correct for movements of a colored model target.  The model was able to detect movements in the tower with average error of 0.32 degrees, and was able to correctly orient the surrounding …

Artificial Neural Networking As A Decision Tool For Natural Gas Investment, Micah D. Denecour

Master's Theses

With the growing interest in the Marcellus Shale and its natural gas deposits, there are opportunities to purchase and hold land for investment purposes. A robust decision tool is needed to help guide investors towards the most profitable properties. Artificial neural networks have many unique benefits that make them an ideal candidate for this purpose.

The artificial neural networks created in this study had nine independent variables. Combinations of these nine variables were created to describe 300 theoretical properties available for purchase. Each of these properties were then evaluated by an expert in the field and given a score from …

Integration Of Aeroservoelastic Properties Into The Nasa Dryden F/A-18 Simulator Using Flight Data From The Active Aeroelastic Wing Program, Alexander Wong Chin

Master's Theses

Aircraft structures have varying stiffness levels making them flexible. Consequently, this elastic property becomes increasingly important at high speeds affecting the flight dynamics of the aircraft.  In high speed aircraft such as the F/A-18, elastic structural properties must be accounted for to ensure confidence in predicted flight dynamics in order to avoid adverse aeroelastic phenomena throughout flight.

Data from the F/A-18 Active Aeroelastic Wing (AAW) program was used to create aeroservoelastic (ASE) models at varying flight conditions. The discretized ASE models were integrated into the NASA Dryden F/A-18 simulator in parallel with the traditional 6-DOF (degrees-of-freedom) flight dynamics calculations to …

Laser Etched Pmma Microfluidic Chip Design And Manufacture With Applications In Capillary Zone Electrophoresis, Evan Allen Barbre

Master's Theses

This thesis encompasses a feasibility study of using low-cost materials to manufacture microfluidic chips that can perform the same functions as chips manufactured using traditional methods within an acceptable range of efficiency of chips created with more exotic methods and materials. The major parts of the project are the selection and characterization of the fabrication methods for creating the channels for fluid flow, the methods for sealing the channels to create a usable chip and the electrophoretic separations of carboxylated microspheres of different potentials. In this work we seek to answer the question if laser-etched PMMA microfluidic chips are comparable …

A Microsimulation Of Traffic, Parking, And Emissions At California Polytechnic State University – San Luis Obispo, Steven Michael Kilbert

Master's Theses

Traffic and parking congestion are significant issues at many universities nationwide. The delays experienced result in wasted time, money, and fuel for students, faculty and staff, not to mention the negative contributions to the environment. This paper quantifies the amount of vehicle emissions generated during an average morning peak hour in the university environment. Using VISSIM and CMEM microsimulation packages, a model is created for California Polytechnic State University- San Luis Obispo to aggregate the collective transportation behaviors and practices of the campus and recognize the implications these behaviors pose on the transportation network as a whole. Reasonable estimates are …