Engineering Commons^™

Dynamic Test Scheduling In Hardware-In-The-Loop Simulation Of Commercial Vehicles, Tenil Cletus

Master's Theses

Modern day commercial vehicles are controlled by various Electronic Control Units (ECU). They are not only tested as single units, but also by networking them in Controlled Area Network bus (CAN) to form a complete electrical control system. This is achieved using Hardware In the Loop (HIL) Integration Lab. In HIL, the electrical system is connected to a real time mathematical model of the vehicle plus it’s environment so as to form a loop.

Testing functionality of the electrical system begins by defining functional tests. An example would be testing cruise control activation. Executing each test is made possible by …

Bias Correction And Downscaling Of Climate Model Outputs Required For Impact Assessments Of Climate Change In The U.S. Northeast, Kazi F. Ahmed

Master's Theses

Global Climate Models (GCMs) are the typical sources of future climate data required for impact assessments of climate change. However, GCM outputs are related to model-related uncertainties and involve a great deal of biases. Bias correction of model outputs is, therefore, necessary before their use in impact studies. The coarse resolution of GCM simulations is another hindrance to their direct use in fine-scale impact analysis of climate change. Although downscaling of GCM outputs can be performed by dynamical downscaling using Regional Climate Models (RCMs), it requires large computational capacity. When daily climate data from multiple GCMs are required to be …

Computational Modeling For Transportation Network Security, Sherif A. Tolba

Master's Theses

No abstract provided.

A Framework For Developing And Integrating Effective Routing Strategies Within The Emergency Decision Support System, Joseph W. Yu

Master's Theses

In recent years transportation professionals have shown increasing interest in evacuation planning. With the advances in computing technologies it is possible to simulate urban transportation networks with great detail. These details from the traffic simulation model can be used for devising strategies for evacuation and emergency response in case of a disaster.

This thesis describes the modeling, calibration, and validation of the VISSIM traffic simulation model coded for downtown San Jose. The network is then used to test various evacuation scenarios to assess evacuation strategies that would be effective in case of a human-caused disaster.

The network modeled in the …

Impedance-Based Detection Of Tissue Using A Multi-Electrode Device, Shane Killian Fleshman

Master's Theses

Melanoma skin cancer is the abnormal growth of the melanocytes – the pigmented cells located in the epidermis. The current gold standard diagnostic technique for determining whether a lesion is cancerous involves subjectively examining suspicious lesions and performing an invasive biopsy to confirm melanoma. This method may neglect some lesions or cause scarring from biopsies that turn out to be benign. Thus, impedance-based detection using a multi-electrode device was investigated as a noninvasive technique to diagnose melanoma skin cancer. The multi-electrode device was designed with 8 equally spaced Ag/AgCl electrodes surrounding one central electrode at a 5 mm radius. The …

Predicting The Acoustic Response Of The Golf Club & Ball Impact Using Finite Elements And The Boundary Element Method, Scott Henry Moreira

Master's Theses

An improved and repeatable method for meshing golf club heads using finite elements in TrueGrid® was developed. Using solid brick elements through the thickness of the club head instead of shell elements better represents the many thickness variations throughout each section of a club head. This method also results in a high quality mesh at the center of the club head sections while still maintaining high quality at the edges. A simulation procedure was also developed to predict the acoustic pressure at a designated point in an acoustic medium of a golf club and ball impact using the BEM and …

Comet: Constrained Optimization Of Multiple-Dimensions For Efficient Trajectories, Michael Curt Conrad

Master's Theses

The paper describes the background and concepts behind a master’s thesis platform known as COMET (Constrained Optimization of Multiple-dimensions for Efficient Trajectories) created for mission designers to determine and evaluate suitable interplanetary trajectories. This includes an examination of the improvements to the global optimization algorithm, Differential Evolution, through a cascading search space pruning method and decomposition of optimization parameters. Results are compared to those produced by the European Space Agency’s Advanced Concept Team’s Multiple Gravity Assist Program. It was found that while discrepancies in the calculation of ΔV’s for flyby maneuvers exist between the two programs, COMET showed a noticeable …

Implementation Of Medicinal Leech Preparation To Investigate The Connection Between The Motor Neuron And Muscle Fiber Via Sharp Electrode Electrophysiology, Chandra Nikole Miller

Master's Theses

There are forty registered organophosphates in the United States and they range from pesticides and insecticides to nerve agents or neurotoxins such as sarin. Organophosphates (OP’s) have been used in chemical warfare for years and tend to lead to death due to an attack on the nervous system. Chemical assays and mass microscopy have been used to assess the concentration of OP’s in the environment, but both methods require the body to metabolize the OP first, which can be detrimental to the victim. It is crucial to come up with a method to investigate and detect these neurotoxins without causing …

Digitally Controlled, Modular Electronic Load, Jason L. March

Master's Theses

This project entails the design and development of a digitally controlled, modular electronic load. The proposed load is unique from existing designs because it has the added ability to increase its maximum current level by adding identical modules in parallel. Each module is designed to sink a maximum of 5A at 60V but more modules allow for more current. The cost and simplicity of the design are considered such that it can be reproduced in-house to replace, whenever possible, the resistor box for load testing of any analog circuits but more specifically power electronic circuits.

The design process as well …

Impact Of Collateral Enlargement On Smooth Muscle Phenotype, Alexander Jerome Bynum

Master's Theses

Peripheral Artery Disease is a very serious disease characterized by an arterial occlusion due to atherosclerotic plaques. In response to an arterial occlusion, arteriogenesis occurs, causing smooth muscle cells to transition from a contractile to synthetic state. Also following an arterial occlusion, functional impairment was seen in the collateral circuit. An immunofluorescence protocol was developed in order to assess the impact of collateral enlargement (arteriogenesis) on smooth muscle phenotype at various time points. Smooth muscle α-actin was used to mark all smooth muscle cells, Ki-67 was used to label proliferating smooth muscle cells, and a fluorescent nuclear stain was used …

Global Optimization Of Mga-Dsm Problems Using The Interplanetary Gravity Assist Trajectory Optimizer (Igato), Jason M. Bryan

Master's Theses

Interplanetary multiple gravity assist (MGA) trajectory optimization has long been a field of interest to space scientists and engineers. Gravity assist maneuvers alter a spacecraft's velocity vector and potentially allow spacecraft to achieve changes in velocity which would otherwise be unfeasible given our current technological limitations. Unfortunately, designing MGA trajectories is difficult and in order to find good solutions, deep space maneuvers (DSM) are often required which further increase the complexity of the problem. In addition, despite the active research in the field over the last 50 years, software for MGA trajectory optimization is scarce. A few good commercial, and …

State Estimation For Tracking Of Tagged Sharks With An Auv, Christina Forney

Master's Theses

Presented is a method for estimating the planar position, velocity, and orientation states of a tagged shark. The method is designed for implementation on an Autonomous Underwater Vehicle (AUV) equipped with a stereo-hydrophone and receiver system that detects acoustic signals transmitted by a tag. The particular hydrophone system used here provides a measurement of relative bearing angle to the tag, but does not provide the sign (+ or -) of the bearing angle. A particle filter was used for fusing measurements over time to produce a state estimate of the tag location. The particle filter combined with an active control …

Cubesat Constellation Analysis For Data Relaying, Bradley Ryan Smalarz

Master's Theses

Current CubeSat communication technology limits the amount of time, and number of accesses with ground stations. It has been proposed to use a constellation of CubeSats to improve relay performance and increase the number of accesses between a CubeSat and ground stations. By using the spatial and temporal analysis features of STK, coupled with the STK/Matlab interface a robust tool was created to analyze the performance of CubeSat constellations based on a store-and-forward communications model which is not currently supported by the STK Engine. Utilizing the Connect messaging format through a socket connection on the local machine, a Matlab graphical …

Seasonal And Anatomical Variation In Compact Bone Remodeling In The Adult Sheep, Joseph Calcagno

Master's Theses

ABSTRACT

SEASONAL AND ANATOMICAL VARIATION IN COMPACT BONE REMODELING IN THE ADULT SHEEP

Joseph Calcagno

In order to determine whether ovine compact bone is suitable for study of osteoporosis, the remodeling parameters of the untreated animal must be fully characterized. Ovine compact bone is an attractive large animal model due to its similarities in size and bone remodeling to humans. However hormonal, exercise, and dietary changes due to seasonal changes can cause treatment effects to be hidden or superimposed on existing changes in the bone. In order to determine if any seasonal or anatomical variation occurred in the compact bone …

Reducing Moisture Damage In Asphalt Mixes Using Recycled Waste Additives, Anthony John Boyes

Master's Theses

This thesis has determined that using fly ash as a mineral filler in asphalt pavements can help strengthen and reduce asphalt moisture damage. Also, dynamic shear rheometer tests show that these additives have a stiffening effect on asphalt binder. Moisture related damage is considered one of the main causes of asphalt pavement failure. As water infiltrates a layer of asphalt, it slowly strips away asphalt binder, weakening the aggregate/binder bond. This process, combined with the cyclic loading of traffic, can lead to several different types of asphalt failure including rutting, raveling, bleeding, and cracking. For several decades, research has been …

Dimensional Stability Of Geosynthetic Clay Liners In Landfill Applications, Gregory R. Olsen

Master's Theses

An investigation was conducted related to the dimensional stability of geosynthetic clay liners (GCLs) in landfill applications. Multiple occurrences of panel separation of overlap seams in GCLs have been documented; however, explanation for the relative contribution of various mechanisms causing shrinkage has been limited. A systematic test program was conducted to determine the effects of a variety of conditions on GCL dimensional stability.

Effects of initial moisture content, permeant type, and overburden pressure were tested by subjecting various GCL products to wet-dry cycles and measuring the dimensional change with each cycle. Different GCL types were each tested under various combinations …

Analysis Of Contrast Enhancement Methods For Infrared Images, Sprinkle Christian

Master's Theses

Contrast enhancement techniques are used widely to improve the visual quality of images. The difference in luminance reflected from two adjacent surfaces creates contrast between the surfaces in the image. The greater the contrast, the easier it is to recognize and differentiate objects in an image. Thus object contrast is an important factor in the perception of the visual quality of an image and in its usefulness for object recognition and image analysis applications.

The focus of this thesis is on studying how well different contrast enhancement techniques developed for visible spectrum photographic images work on infrared images; to determine …

Modeling And Analysis Of A Four-Switch Buck-Boost Dynamic Capacitor, Oscar Plasencia

Master's Theses

Modern electric power utilities are facing a variety of challenges introduced by the increasing complexity of their operation, structure, and consumer loads. One such challenge has been to supply the ever growing demand for reactive power which is essential for grid support. For this reason dynamic VAR technologies are becoming much more important to modern day power systems. A recent dynamic VAR technology known as the Dynamic Capacitor offers full quadrant capacitive VAR control through the combination of AC/AC buck and boost cells. This paper introduces a new topology deemed the “Four-Switch Buck-Boost Dynamic Capacitor” which promises to combine the …

Experimental Investigation Of A 2-D Air Augmented Rocket: Effects Of Nozzle Lip Thickness On Rocket Mixing And Entrainment, Trevor Allen Montre

Master's Theses

Cold-flow tests were performed using a simulated Air Augmented Rocket (AAR) operating as a mixer-ejector in order to investigate the effects of varied primary nozzle lip thickness on mixing and entrainment. The simulated primary rocket ejector was supplied with nitrogen at a maximum chamber stagnation pressure of 1712 psi, and maximum flow rate of 1.67 lb_m/s. Secondary air was entrained from a plenum, producing pressures as low as 6.8 psi and yielding maximum stagnation pressure ratios as high as 160. The primary ejector nozzles each had an area ratio of approximately 20, yielding average primary exit Mach numbers …

Enhancement Of Light Absorption Efficiency Of Solar Cell Using Dual, Ashton Ellaboudy

Master's Theses

In this research we study the effect of adding a single diffraction grating on top of a solar cell. We simulated the square diffraction grating, as well as triangular diffraction grating. The single square grating showed more favorable results, achieved 330% power improvement compared to 270% power improvement in the single triangular grating case.

We simulated a triangle/triangle (top-bottom) and triangular/rectangular (top-bottom) grating cases. The Triangular grating achieved higher light absorption compared to rectangular grating. The best top grating was around 200nm grating period. We realized solar cell efficiency improvement about 42.4% for the triangular rectangular (top-bottom) grating.

We studied …

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh

Master's Theses

Plug-in Electric Vehicles (PEVs) are projected to become a viable means of transportation due to advances in technology and advocates for green and eco-friendly energy solutions. These vehicles are powered partially, or in some cases, solely by the energy stored in their battery packs. The large sizes of these battery packs require large amount of energy to charge, and as the demand for PEV increases, the increase in energy demand needed to recharge these PEV batteries could pose problems to the present electric distribution system. This study examines the potential impacts of PEV on a residential electric distribution system at …

Implementation And Validation Of The Ζ-F And Asbm Turbulence Models, Dustin Van Blaricom Quint

Master's Theses

The use of Computational Fluid Dynamics (CFD) tools throughout the engineering industry has become standard. Simulations are used during nearly all steps throughout the life cycle of products including design, production, and testing. Due to their wide range of use, industrial CFD codes are becoming more flexible and easier to use. These commercial codes require robustness, reliability, and efficiency. Consequently, linear eddy viscosity models (LEVM) are used to model turbulence for an increasing number of flow types. LEVM such as k-ε and k-ω provide modeling with little loss of computational efficiency and have proven to be robust. The LEVM that …

Effects Of Column Stiffness On Seismic Behavior Of Steel Plate Shear Walls, Xuhua Guo

Master's Theses

Steel plate shear walls (SPSWs) are a lateral force resisting system consisting of thin infill steel plates surrounded by boundary frame members. The infill steel plates are allowed to buckle in shear and subsequently form diagonal tension field actions during earthquake events. Hysteretic energy dissipation of this system is primarily achieved through yielding of the infill plates. Conceptually, in a SPSW system with ideally rigid columns pinned to ground, the infill plates at different stories will yield simultaneously as a result of the lateral loads. However, when the columns become flexible, infill plate yielding may initially occur at one story …

Formulation Of An Optimal Search Strategy For Space Debris At Geo, Daniel J. Jackson

Master's Theses

The purpose of this thesis is to create a search strategy to find orbital debris when the object fails to appear in the sky at its predicted location. This project is for NASA Johnson Space Center Orbital Debris Program Office through the MODEST (Michigan Orbital Debris Survey Telescope) program. This thesis will build upon the research already done by James Biehl in “Formulation of a Search Strategy for Space Debris at GEO.” MODEST tracks objects at a specific right ascension and declination. A circular orbit assumption is then used to predict the location of the object at a later time. …

Detecting Suspicious Behavior With Low-Cost Sensors, Ahren Alexander Reed

Master's Theses

A proof of concept is created that demonstrates how low-cost sensors and a simple software solution can be used to proactively detect IED placement. The main goal is to detect suspicious behavior; Specifically we derive requirements that loitering, meandering, improper location and object placement shall be detected. Current methods being used to detect Improvised Explosive Devices (IEDs) are costly in terms of equipment and risk to life, and many are retroactive; IED detection occurs long after explosives are placed. A prototype system is explored with the quality attributes of being low-cost, proactive and using simple software methods. A wireless sensor …

An Automated Test Station Design Used To Verify Aircraft Communication Protocols, Joshua Berrian

Master's Theses

Requirements verification is typically the costliest part of the systems engineering design process. In the commercial aircraft industry, as the software and hardware design evolves, it must be verified to conform to requirements. In addition, when new design releases are made, regression analysis must be performed which usually requires repeat testing. To streamline verification, a suite of automated verification tools is described in this document which can reduce the test effort. This test suite can be qualified to be used to verify systems at any DO-178B design assurance level. Some of the software tools are briefly described below.

There are …

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander

Master's Theses

Ground Fault Circuit Interrupter (GFCI) technology was first introduced in the NEC in 1971, yet four decades later the technology has not been introduced to a great extent outside of the home environment. This thesis introduces the difficulties encountered in low-voltage three phase ground fault current detection, and adopts a previously patented tripping scheme to develop and prototype a digital relay for 3-phase 480 volt systems capable of the sensitivity and speed required for personnel safety. Results demonstrate the feasibility of the concept and suggest commercial development should be pursued. The prototype is capable of mA sensitivity and reliably detects …

Accurate Estimation Of Isoform And Gene Expression Levels From Next Generation Sequencing Data, Marius Nicolae

Master's Theses

Massively parallel transcriptome sequencing is quickly replacing microarrays as the technology of choice for performing gene expression profiling due to its wider dynamic range and digital quantitation capabilities. However, accurate estimation of expression levels from sequencing data remains challenging due to the short read length delivered by current sequencing technologies and still poorly understood protocol- and technology-specific biases.

To date, two main transcriptome sequencing protocols have been proposed in the literature. The most commonly used one, referred to as RNA-Seq, generates short (single or paired) sequencing tags from the ends of randomly generated cDNA fragments. An alternative protocol, referred to …

Understanding Formation And Transport Of Amorphous Iron Oxyhydroxides In Porous Media Using Microfluidic Flow Cells- A Novel Method To Study Freshwater Iron Cycling, Neha A. Ghaisas

Master's Theses

The ground water and surface water interface (GSI or Hyporheic zone) is a spatially- and temporally-fluctuating biogeochemical transition zone connecting these two distinct hydrological components. The mixing zone is characterized by a near neutral pH, ambient temperature and a sharp oxygen concentration which in turn has deep impact on the iron cycling and thus the fate of contaminants in the water column. We constructed an experimental micromodel that to observe key processes that affect biogeochemical iron cycling in the fresh water interface zones where the oxic surface water mixes with Fe (II) rich underlying ground water. The flow cell was …

Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells, Alexander M. Lassman

Master's Theses

Solid oxide fuel cells (SOFC) have gained a great deal of interest, due to their potential for high efficiency power generation and ability to utilize hydrogen fuel, as well as various hydrocarbon-based fuels. A recent trend in SOFC development has been towards lower operating temperatures (500-700°C), which can substantially reduce the cost and complexity of the system. This thesis presents an investigation into state of the art Ba- and La- based cathode materials for use in low temperature (500-700°C) solid oxide fuel cells.

Synthesis of A-site deficient [A=0.97] Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃ (BSCF) was …