Engineering Commons^™

Modal Analysis Of Composite Structures With Damping Material, Kellie Michelle Tremaine

Master's Theses

The purpose of this study is to develop an analytical solution for modal analysis of actively damped orthotropic composite plates in bending and to verify it with experimental analysis.

The analytical modal analysis solution for composite plate dynamics is derived using Euler theory. This analysis applies to structures with orthotropic lamina of uniform material properties at any lamination angle. The bending-extensional coupling can be neglected for plates that are symmetric or approximately symmetric, which allows an exact solution for natural frequency and mode shape to be obtained. An exact solution can be found for natural vibration and in general.

The …

An Investigation Of Damage Arrestment Devices On Carbon Fiber Sandwich Specimens Under Dynamic Loading, Gabriel Sabino Sanchez

Master's Theses

This research studies the effects of a damage arrestment device embedded between a carbon fiber facesheet and foam core to find whether there is an increase in the structural integrity of the sandwich composites. Experimental and theoretical finite element analyses are implemented for two different composite sandwich geometries; plates and beams. Each structure consisted of the same loading criteria and was restricted to the same vibration fixture during the experiment. An accelerometer was placed on the composite plate to record the amplitude and the natural frequencies of the composite structure. Each composite specimen is then fixed to the surface of …

Development And Characterization Of Phospholipid Encapsulated Quantum Dot Constructs For Biologic Applications, Laura C. Sparks

Master's Theses

DEVELOPMENT AND CHARACTERIZATION OF PHOSPHOLIPID ENCAPSULATED QUANTUM DOT CONSTRUCTS FOR BIOLOGIC APPLICATIONS

The American Cancer Society predicts that 577,190 cancer-related deaths and 1,638,910 newly diagnosed cases of cancer will occur in 2012. As these statistics show, cancer is a prevalent and devastating health issue; determined by the Mayo Clinic to be the second leading cause of death in the United States. Skin cancer is the most common form of cancer in the United States. In 2012 more than 68,000 Americans will be diagnosed with melanoma, 48,000 will be diagnosed with an early form of the disease that has not yet …

Flying Qualities Built-In-Test For Unmanned Aerial Systems, Alton Pak-Hin Chiu

Master's Theses

This paper presents a flying qualities built-in-test for UAS application with the scope limited to the longitudinal axis. A doublet input waveform excites the AV and both α and q are used by EUDKF to estimate the A and B matrices which are short period approximations of the system. ζ, ω, GM, PM, observability, and controllability are calculated to determine flying qualities with the results displayed to the AVO in a color-coded, easy to interpret display.

While SID algorithms have been flying in vehicles with adaptive control schemes, vehicles with other schemes (such as classical feedback) lack this built-in self …

Detecting Netflix Service Outages Through Analysis Of Twitter Posts, Cailin Cushing

Master's Theses

Every week there are over a billion new posts to Twitter services and many of those messages contain feedback to companies about their services. One company that has recognized this unused source of information is Netflix. That is why Netflix initiated the development of a system that will let them respond to the millions of Twitter and Netflix users that are acting as sensors and reporting all types of user visible outages. This system will enhance the feedback loop between Netflix and its customers by increasing the amount of customer feedback that is being received by Netflix and reducing the …

Activity Node Based Flight Software As A Benefit To Systems Engineering, Eugene Daniel Lewis

Master's Theses

This report discusses one application of a flight software design for a spacecraft in which the software executes from a database that can be managed by systems engineering. This report gives an overview of how such a software design can be developed and implemented. It also discusses why this approach is beneficial to the systems engineering program.

Light Extraction Enhancement Of Gan Based Leds Using Top Gratings, Patterned Sapphire Substrates, And Reflective Surfaces, Greg Chavoor

Master's Theses

In the last 15 years, an immense amount of research has gone into developing high efficiency Gallium Nitride based light emitting diodes (LED). These devices have become increasingly popular in LED displays and solid state lighting. Due to the large difference in refractive index between GaN and Air, a significant amount of light reflects at the boundary and does not escape the device. This drawback decreases external quantum efficiency (EQE) by minimizing light extraction. Scientists and engineers continue to develop creative solutions to enhance light extraction. Some solutions include surface roughening, patterned sapphire substrates, and reflective layers.

This study proposes …

Comparative Analysis Of Erp Emerging Technologies, Ryan Engebrethson

Master's Theses

This Master's Thesis compares technologies used in the architecture of Enterprise Resource Planning (ERP) Systems to evaluate the benefits and advantages of emerging technologies. The emerging technologies, Cloud Computing, Software as a Service (SaaS) and Multi-Tenancy, could significantly alter the current ERP space and become a primary part of ERP Systems of the future. A survey was sent to industry professionals to obtain feedback on their company's ERP Systems and to collect their comments on these new technologies. The survey results and related analysis show that Emerging Cloud ERP Systems outperform Traditional Legacy ERP Systems in all important characteristics - …

Effects Of Ovariectomy, Seasonal Changes, And Anatomical Position On The Compact Bone Remodeling As Seen In The Adult Ovine Model, Erica Wong

Master's Theses

The purpose of this study is to characterize the compact bone remodeling of the ovariectomized ewe and its effectiveness as an animal model for studies of postmenopausal osteoporosis. The use of animal models is a beneficial way to evaluate the effectiveness of medical devices and therapeutic agents for treating diseases. The ovine model is an attractive option because of its large size and similar bone remodeling to humans. However, this species, like most animals, does not undergo a natural menopause, making an ovariectomy necessary for studies of estrogen depletion. The OVX (ovariectomized) sheep has been widely accepted as a model …

Evaluation Of A Novel Axial Flux Variable Reluctance Machine, Derek Braden Hines

Master's Theses

The objective of this thesis is to determine the feasibility of a novel axial flux variable reluctance machine design. The design aims to compete with prevalent rare-earth permanent magnet machines while also implementing an innovative torque ripple minimization strategy. Given the fundamental operating principles, a selection of dimensions, materials, and excitations are prepared for the machine. Special attention is given to the rotor profile which is crucial to operation. Finite element analysis software is used to evaluate a three-dimensional model in terms of inductance and torque. The ultimate potential of the machine is discussed and recommendations for improvement are proposed.

Short Term Monitoring Of Suspender Cables On An In-Service Highway Bridge, Gannon Stromquist-Levoir

Master's Theses

No abstract provided.

Agent-Based Modeling Of Emergency Building Evacuation, Vi Q. Ha

Master's Theses

Panic during emergency building evacuation can cause crowd stampede, resulting in serious injuries and casualties. Agent-based methods have been successfully employed to investigate the collective human behavior during emergency evacuation in cases where the configurational space is extremely simple - usually one rectangular room - but not in evacuations of multi-room or multi-floor buildings. This implies that the effect of the complexity of building architecture on the collective behavior of the agents during evacuation has not been fully investigated. Here, we employ a system of self-moving particles whose motion is governed by the social-force model to investigate the effect of …

Using Ground Penetrating Radar Signal Reflection To Model A Highly Transmissive Bedrock Aquifer, Daniel J. Brockmeyer Mr.

Master's Theses

The use of numerical modeling software to characterize groundwater contaminant fate and transport requires an understanding of the distribution of hydraulic properties of the aquifer. As the complexity of this distribution increases, a more sophisticated understanding is required. Modeling contaminant transport in bedrock aquifers requires that the spatial distributions of highly conductive geologic features are characterized along with the hydraulic transmissivities of those features (Shapiro, 2003). The goal of this research is to refine the numerical model of a highly transmissive crystalline aquifer by characterizing the spatial variability of the hydraulic transmissivity using the attenuation of the ground penetrating radar …

A Stochastic Simulation Model Of Alarm Response Strategies On A Telemetry Floor, Tasneem M. Pishori

Master's Theses

The large quantity of alarms characteristic of clinical settings have resulted in nursing staff suffering from a phenomenon termed ‘alarm fatigue’. Alarm fatigue is desensitization via habituation – as these commonly heard noises cause caregivers to have delayed or no response to alarms. Alarm management was ranked number one on the annual top ten list of technology hazards afflicting healthcare institutions published by the ECRI Institute for 2012. Several patient safety organizations have established alarm fatigue as a priority concern, and are working to eradicate the issue from the healthcare environment by 2017. To better understand the problem, a simplified …

High Speed Atomic Force Microscopy Techniques For The Efficient Study Of Nanotribology, James L. Bosse

Master's Theses

As mechanical devices scale down to micro/nano length scales, it is crucial to understand friction and wear at the nanoscale (nanotribology) especially at technically relevant sliding velocities. Accordingly, three novel techniques have been developed to study nanotribology, leveraging recent advances in high speed AFM. The first method utilizes high line-scanning rates coupled with sinusoidal scanning along the AFM fast scan axis, enabling rapid friction measurements as a function of velocity up to 20 mm/sec. The second method rapidly acquires friction versus force curves through disabling the feedback loop during scanning and relating the resulting lateral data with the correspondingly varying …

Nanocharacterization Of Porous Materials With Atomic Force Microscopy, Yasemin Kutes

Master's Theses

Scanning Probe Microscopy techniques have proven very useful in the investigation of porous nanostructured surfaces. Especially, Atomic Force Microscopy (AFM) has been widely used due to its compatibility with non-conducting surfaces. In particular, AFM often complements other techniques like scanning and transmission electron microscopy by providing quantitative surface information coupled with nanoscale spatial resolution. Its ability to operate in fluid is also important, as this allows researchers to mimic the physiological environment of biological materials and systems. In this work, two main types of porous materials are studied with AFM, including Phosphoric Acid Fuel Cell (PAFC) electrode catalyst layers, and …

Creating A Pedestrian Level-Of-Service Index For Transit Stops: Evidence From Denver’S Light Rail System, Patrick Gallagher

Master's Theses

No abstract provided.

Development And Application Of A Portable System To Reliably Measure Grip Forces Using Thin-Film Force Sensors, Shane Vincent Tornifoglio

Master's Theses

Accurate tracking of hand grip force is an important consideration needed for a robust understanding in the study of human biomechanics. One aspect where it proves useful is in hand-arm vibration, such as from gripping a power tool. Depending on how firmly the user is gripping the tool, they may change their exposure levels to the tool vibration, which can lead to potential disorders such as Hand-Arm Vibration Syndrome (HAVS).

A small, battery powered portable force unit has been developed to supply power to, and condition, the signals from eight thin-film force sensors. This gives a better understanding of the …

Eurotech Students In Germany: Preparation, Experience And Outcome, Daisy A. Michaels

Master's Theses

Higher education study abroad programs for U.S. students are on the rise. A variety of undergraduate disciplines are being coupled with international components to bring U.S. students to a higher level of global awareness to meet the demands of today’s economy. The University of Connecticut’s Eurotech Program is an example of this trend. Its students earn degrees in both German and engineering in a five year program. They are given practical training through study and internships in Germany under the auspices of the Baden-Württemberg Exchange Program. One of the Eurotech Program’s major goals is to enhance job opportunities for its …

Computer-Aided Engineering Tools For Structural Health Monitoring Under Operational Conditions, Priscilla O. Mensah-Bonsu

Master's Theses

This thesis presents two different applications of computer-aided non-destructive approaches for structures monitored under operational conditions. The first part of the thesis is the development of a graphical user interface (GUI) software for real-time autonomous assessment of structural health condition based on the signature vibration properties of the structure under study. The program, called ConImote2, operates on the wireless sensor network platform called imote2. ConImote2 is created in the Matlab platform for accessibility and to enable extension of its capabilities by the user. The primary goal of creating the program is to overcome the issue of data inundation from SHM …

A Comprehensive Methodology For Assessing Biomechanical Risks Associated With Hand Tool Use: Applied To Laparoscopic Surgical Instruments, Drew R. Seils

Master's Theses

Biomechanical risk factors are physical stressors that act on the neuromuscular structures of the human body and are present in all occupational settings. Repetition and intensity of tasks performed can magnify the effects of the biomechanical risks that a worker is exposed to.

After reviewing the current literature on ergonomics in laparoscopic surgery it was clear that a comprehensive approach to quantitatively reporting on the biomechanical risk factors associated with surgical hand tools had never been performed. Utilizing an opto-electronic motion capture system meant the exact surgeon posture was recorded during simulated surgical tasks. Electromyography was used to evaluate muscle …

Laboratory And Field Evaluation Of Two Warm-Mix Additives In Connecticut And Validation Of An Alternative Moisture Susceptibility Test, Alexander K. Bernier

Master's Theses

The first official state Warm-Mix Asphalt (WMA) pavement project in Connecticut was constructed between July 20th and 22nd, 2010 and it involved three experimental sections, i.e. one section with a conventional HMA (control section) and two WMA sections with different technologies, wax and foamed asphalt. All three sections are located on Route 70 in central Connecticut. The materials were collected in loose form and reheated and compacted in laboratory conditions (laboratory fabricated specimens). This paper discusses the effect of mix type on the results from several tests conducted in the laboratory, such as Semi-Circular Bending, Hamburg Wheel Tracking, Indirect Tensile, …

Advanced Design Optimization For Composite Structure: Stress Reduction, Weight Decrease And Manufacturing Cost Savings, Shayan Ahmadian

Master's Theses

An injection moldable chopped fiber composite actuator with detailed drawing and tolerances was designed within one year. A vendor was selected and a quote for injection molding tooling cost for production was obtained and the first prototype was built in addition of six months. The risks are identified and material characterization tests are proposed.

The objective of this project was redesigning an aluminum made actuator with a continuous fiber composite for weight saving purposes. After searching the literature and consulting with experts in the field it was concluded that manufacturing costs associated with continuous fiber composite are 3 times as …

An Investigation Of Fraxinus Americana Branch Sway Using A 3 Dimensional Motion Capture System, Anna T. Campiformio

Master's Theses

Abstract

Wind is a dominant abiotic factor that a tree experiences throughout its lifetime and can cause severe tree damage, resulting in risk of injury to humans, and economic and ecological losses. It is thought that trees develop structural properties and architectures that help withstand loading conditions by dissipating wind energy through damping mechanisms. The role of branch motion in reducing potential dangerous wind loads has been the focus of relatively few studies. Even fewer studies have examined tree sway response to natural wind loaded conditions. In this investigation, branch frequencies were calculated for three Fraxinus americana using a three-dimensional …

Modeling And Analysis Of A Photovoltaic System With A Distributed Energy Storage System, Anthony Winston Ma

Master's Theses

As California continues to integrate more renewable energy into its electrical system, the state has experienced a corresponding rise in photovoltaic system installations. PV arrays are a unique source of power generation in that they are affected by the location of the sun, shading, and temperature changes. These characteristics make solar one of the most highly variable forms of renewable energy. In order to improve solar power’s consistency, PV systems require a supplemental source of power. The primary focus of this paper is to determine if distributed energy storage systems can be used to reduce the effect of solar intermittency. …

Sun-Synchronous Orbit Slot Architecture Analysis And Development, Eric Watson

Master's Theses

Space debris growth and an influx in space traffic will create a need for increased space traffic management. Due to orbital population density and likely future growth, the implementation of a slot architecture to Sun-synchronous orbit is considered in order to mitigate conjunctions among active satellites. This paper furthers work done in Sun-synchronous orbit slot architecture design and focuses on two main aspects. First, an in-depth relative motion analysis of satellites with respect to their assigned slots is presented. Then, a method for developing a slot architecture from a specific set of user defined inputs is derived.

Multi-Circle Detections For An Automatic Medical Diagnosis System, Dingran Lu

Master's Theses

Real-time multi-circle detection has been a challenging problem in the field of biomedical image processing, due to the variable sizes and non-ideal shapes of cells in microscopic images. In this study, two new multi-circle detection algorithms are developed to facilitate an automatic bladder cancer diagnosis system: one is a modified circular Hough Transform algorithm integrated with edge gradient information; and the other one is a stochastic search approach based on real valued artificial immune systems. Computer simulation results show both algorithms outperform traditional methods such as the Hough Transform and the geometric feature based method, in terms of both precision …

Primary And Secondary Flow Interactions In The Mixing Duct Of A 2-D Planer Air Augmented Rocket, Martin Roy Popish

Master's Theses

Experiments were conducted on the Cal Poly air augmented rocket (AAR) in order to characterize two-dimensional flowfield phenomenon occurring in the mixing duct. The testing utilized a direct connect system where high pressure nitrogen is fed into the combustion chamber, to form a primary flow. The high pressure nitrogen is then expanded through a nozzle, with an area ratio of 22 and an exit area of 0.75 in², up to Mach 4.3. Secondary air is entrained from a plenum chamber which is used to create a lower stagnation pressure for the secondary flow. The two flows mix in …

Investigation Of A Commercial Product (Biowish™) For Nitrogen Management, Eva Lee

Master's Theses

Abstract

Investigation of a Commercial Product (BiOWiSH­­^TM) for Nitrogen Management

Eva Lee

BiOWiSH–Aqua, which has the capability of treating nitrogen from wastewater through bioaugmentation, is a commercial product consisting of a blend of microorganisms developed by BiOWiSH Technologies. A study of the treatment of nitrogen compounds (i.e. , , and ) using Biowish–Aqua was conducted using small scale experiments (flask experiments) and large scale experiments (column reactor experiments). In this work, column reactors were created to test Biowish–Aqua’s nitrogen treating capabilities by providing enough depth to simulate the dissolved oxygen gradient that can be observed in a pond. …

Dsm64: A Distributed Shared Memory System In User-Space, Stephen Alan Holsapple

Master's Theses

This paper presents DSM64: a lazy release consistent software distributed shared memory (SDSM) system built entirely in user-space. The DSM64 system is capable of executing threaded applications implemented with pthreads on a cluster of networked machines without any modifications to the target application. The DSM64 system features a centralized memory manager [1] built atop Hoard [2, 3]: a fast, scalable, and memory-efficient allocator for shared-memory multiprocessors.

In my presentation, I present a SDSM system written in C++ for Linux operating systems. I discuss a straight-forward approach to implement SDSM systems in a Linux environment using system-provided tools and concepts avail- …