Engineering Commons^™

Examining The Effects Of Reducing The Cement Content Of Portland Cement Concrete Pavement, Bryan Casillas

Graduate Theses and Dissertations

Portland cement is a significant component in a concrete mixture. For concrete used in portland cement concrete pavement (PCCP), the Arkansas Department of Transportation (ARDOT) specifies a minimum cementitious material content of 564 lb/yd3 and a maximum water-cementitious material ratio of 0.45. Prior research conducted at the University of Arkansas, TRC 0603, indicated concrete mixtures used in five bridge decks throughout Arkansas achieved the required 28-day strength at seven days, and the measured compressive strength at 28 days was 30% greater than required. The use of high strength concrete in pavements throughout the state can increase cracking and consequently reduce …

Quantifying Workability, Compactability, And Cohesion Gain Of Asphalt Emulsion Cold In-Place Recycling, Sadie Casillas

Graduate Theses and Dissertations

To maximize the life and quality of a pavement, proper maintenance and rehabilitation are essential. Strategies for pavement rehabilitation with many sustainable benefits are pavement recycling. This dissertation focuses on two types of in-situ pavement recycling: Cold in-place recycling (CIR) stabilized with asphalt emulsion and full depth reclamation (FDR) stabilized with asphalt emulsion or foamed asphalt. One white paper (Chapter 2), two accepted peer reviewed journal articles (Chapters 3 and 4), and one submitted peer reviewed journal article (Chapter 5) are presented in this document to create better understanding of the unique material characterization of asphalt emulsion cold recycled materials, …

Verifying The Calcium Oxychloride Threshold In Cementitious Pastes, Fatoumata Traore

Graduate Theses and Dissertations

Calcium oxychloride (CAOXY) formation is a serious deterioration mechanism known to cause joint damage in concrete pavements. CAOXY is the product of a chemical reaction between calcium chloride (CaCl2) or magnesium chloride (MgCl) deicing salts and calcium hydroxide in the cementitious matrix. Currently, the accepted CAOXY threshold at which deterioration is mitigated in cementitious paste is 15 g/100 g paste (15 oz/100 oz paste); however, this limit was developed using flexural strength testing. For this investigation, the current threshold was evaluated using compressive strength and mass change over time in paste specimens exposed to CaCl2. Fly ash is used to …

Commodity-Based Freight Activity On Inland Waterways Through The Fusion Of Public Datasets For Multimodal Transportation Planning, Magdalena I. Asborno

Graduate Theses and Dissertations

Within the U.S., the 18.6 billion tons of goods currently moved along the multimodal transportation system are expected to grow 51% by 2045. Most of those goods are transported by roadways. However, several benefits can be realized by shippers and consumers by shifting freight to more efficient modes, such as inland waterways, or adopting a multimodal scheme. To support such freight growth sustainably and efficiently, federal legislation calls for the development of plans, methods, and tools to identify and prioritize future multimodal transportation infrastructure needs. However, given the historical mode-specific approach to freight data collection, analysis, and modeling, challenges remain …

Nonlinear Dimensionality Reduction For The Thermodynamics Of Small Clusters Of Particles, Aditya Dendukuri

Graduate Theses and Dissertations

This work employs tools and methods from computer science to study clusters comprising a small number N of interacting particles, which are of interest in science, engineering, and nanotechnology. Specifically, the thermodynamics of such clusters is studied using techniques from spectral graph theory (SGT) and machine learning (ML). SGT is used to define the structure of the clusters and ML is used on ensembles of cluster configurations to detect state variables that can be used to model the thermodynamic properties of the system. While the most fundamental description of a cluster is in 3N dimensions, i.e., the Cartesian coordinates of …

Converter- And Module-Level Packaging For High Power Density And High Efficiency Power Conversion, Amol Rajendrakumar Deshpande

Graduate Theses and Dissertations

Advancements in the converter- and module-level packaging will be the key for the development of the emerging high-power, high power-density, high-eciency power conversion applications, such as traction, shipboards, more-electric-aircraft, and locomotive. Wide bandgap (WBG) devices such as silicon carbide (SiC) MOSFET attract much attention in these applications for their fast switching speeds, resulting in low loss and a consequent possibility for high switching frequency to increase the power density. However, for high-current, high power implementations, WBG devices are still available in small die sizes. Multiple SiC devices need to be connected in parallel to replace a large IGBT die. It …

Investigation Of The Structural, Electronic, And Thermoelectric Properties Of Mono- Chalcogenides, Aida Sheibani

Graduate Theses and Dissertations

The structural, electronic, and thermoelectric properties of GeTe are studied using density functional theory and Boltzmann transport equations. This material has a rhombohedral crystal structure in ambient temperature with a ferroelectric behavior due to lack of inversion symmetry. This study suggests that the presence of asymmetry in GeTe can lead to an improvement in the thermoelectric properties of this material. In addition, studies on introducing Group III, IV, and V dopants to GeSe show that while these impurities can improve the power factor and decrease the lattice thermal conductivity, they cannot enhance the figure of merit.

Machine Tool Communication (Mtcomm) Method And Its Applications In A Cyber-Physical Manufacturing Cloud, S M Nahian Al Sunny

Graduate Theses and Dissertations

The integration of cyber-physical systems and cloud manufacturing has the potential to revolutionize existing manufacturing systems by enabling better accessibility, agility, and efficiency. To achieve this, it is necessary to establish a communication method of manufacturing services over the Internet to access and manage physical machines from cloud applications. Most of the existing industrial automation protocols utilize Ethernet based Local Area Network (LAN) and are not designed specifically for Internet enabled data transmission. Recently MTConnect has been gaining popularity as a standard for monitoring status of machine tools through RESTful web services and an XML based messaging structure, but it …

Towards A Cyber-Physical Manufacturing Cloud Through Operable Digital Twins And Virtual Production Lines, Md Rakib Shahriar

Graduate Theses and Dissertations

In last decade, the paradigm of Cyber-Physical Systems (CPS) has integrated industrial manufacturing systems with Cloud Computing technologies for Cloud Manufacturing. Up to 2015, there were many CPS-based manufacturing systems that collected real-time machining data to perform remote monitoring, prognostics and health management, and predictive maintenance. However, these CPS-integrated and network ready machines were not directly connected to the elements of Cloud Manufacturing and required human-in-the-loop. Addressing this gap, we introduced a new paradigm of Cyber-Physical Manufacturing Cloud (CPMC) that bridges a gap between physical machines and virtual space in 2017. CPMC virtualizes machine tools in cloud through web services …

A Study Of The Thermodynamics Of Small Systems And Phase Transition In Bulk Square Well-Hard Disk Binary Mixture, Gulce Kalyoncu

Graduate Theses and Dissertations

Under the umbrella of statistical mechanics and particle-based simulations, two distinct problems have been discussed in this study. The first part included systems of finite clusters of three and 13 particles, where the particles are interacting via Lennard Jones potential. A machine learning technique, Diffusion Maps (DMap), has been employed to the large datasets of thermodynamically small systems from Monte Carlo simulations in order to identify the structural and energetic changes in these systems. DMap suggests at most three dimensions are required to describe and identify the systems with 9 (N = 3) and 39 (N = 13) dimensions. At …

Development Of High-Density Propulsion System Technologies For Interplanetary Small Satellites And Cubesats, Morgan Andrew Roddy

Graduate Theses and Dissertations

The goal of this research was to support the development of a novel propulsion system for small satellites (<180 kg) and CubeSats. This was pursued by conducting a collection of studies that were designed to provide engineering data that would be critical in designing a functional prototype. The novel propulsion system was conceived by the author to provide best-in-class performance for the small satellite and CubeSat families of spacecraft. This context presents specific design requirements that the presented technology attempts to satisfy. The most critical among these is high density; the propellant was designed to be stored with high density and the thruster was designed to be as compact as possible. The propulsion system is composed of two primary elements, a propellant generator and a thruster. The propellant generator works by sublimating a solid crystal into vapor and then using this vapor to etch a dense metal. The resulting gaseous byproducts of this reaction are the propellant. This dissertation used xenon difluoride (XeF2) vapor to etch tungsten (W) which react to form xenon gas (Xe) and tungsten hexafluoride (WF6). This approach gave a theoretical propellant storage density 5.40 g/cm3; and 5.17 g/cm3 was demonstrated. The sublimation dynamics of the XeF2 were studied as a function of surface area and temperature and it was found to be suitable for the intended application due to its high effluence rate; that is, it sublimates fast enough to be useful. The sublimation rates are on the order of 10’s of µg/s. The etch rate of XeF2 on W was also studied and found to be suitably fast to provide useful amounts of reactants for use as a propellant, again on the order of 1’s of µg/s. The thruster is an electrostatic radio frequency (RF) ion thruster design and is manufactured with Low Temperature Co-Fired Ceramic (LTCC) materials system and manufacturing technology. Manufacturing samples of the thruster were built at the University of Arkansas in July 2015 and tested at NASA’s Marshall Space Flight Center in May 2018. Testing validated the viability of the LTCC thruster and provided valuable information on how to improve the thruster’s design.

Conducted Emi Mitigation In Power Converters Using Active Emi Filters, Balaji Narayanasamy

Graduate Theses and Dissertations

Wide bandgap devices enable high power density power converters. Despite the advantages of increased switching frequency, the passive components are still a major bottleneck towards enabling high power density. Among the passive components in the converter, the passive EMI filters are unavoidable to ensure compliance with conducted EMI standards. Active EMI filters help reduce the volume of the passive components and have been around for three decades now. Firstly, this work presents a summary of all the different active EMI filters based on the type of noise-sensing, noise-processing, the type of active circuits used and the type of control methods. …

Towards High Efficiency And High Power Density Converter: System Level Design, Modulation, And Active Emi Filters, Hongwu Peng

Graduate Theses and Dissertations

Power converter exposes strong challenges to its efficiency, power density and reliability. For the grid-connected inverter application, three-level (3-L) T-type neutral-point-clamped (TNPC) inverters has higher efficiency and lower total harmonic distortion (THD) compared to two-level inverter. Hybrid switch concept combines the benefit of both silicon carbide (SiC) MOSFET and Si IGBT. By applying hybrid switch structure in 3-L T-type inverter, the total power density of 3-L TNPC inverter will be higher while the cost will be lower than that of all-SiC 3-L T-type inverter. The hybrid switch based 3-L TNPC inverter also imposes challenge to its modulation and control, a …

Synthesis And Application Of Ceramic Paste For High-Temperature Electronic Packaging, Ardalan Nasiri

Graduate Theses and Dissertations

This dissertation research focused on the synthesis and application of ceramic paste for high-temperature applications. An alumina paste material comprising aluminum dihydric phosphate and alumina powder was developed for high-temperature electronic packaging. Nano aluminum nitride and nano-silica powders were embedded to promote the paste curing process, limit the grain growth, and increase its bond shear strength. The chip-to-substrate bond strength was enhanced and met the MIL-STD requirements for die-attach assembly. Its encapsulation property was improved with fewer cracks compared to similar commercial ceramic encapsulants. The die-attach material and encapsulation properties tested at 500°C showed no defect or additional cracks. Thermal …

Design Of Control System With Feedback Loop For A Pulsatile Pump, Ian Scott Sanders

Graduate Theses and Dissertations

This paper describes the design and implementation of a closed-loop proportional, integral, differential (PID) control system for a custom in-house pulsatile pump apparatus for the University of Arkansas Biomedical Department. The control system is designed to control a MOONS’ PL34HD0L8500 hybrid stepper motor using a dual H-bridge motor driver network with four pulse-width modulated (PWM) inputs to drive a pulsatile pump apparatus at motor stepping frequencies up to 2kHz. The speed of the motor is controlled from a pressure profile transmitted from an external source over RS-232 communication that specifies the motor speed, number of datapoints, and an array of …

Study On New Sampling Plans And Optimal Integration With Proactive Maintenance In Production Systems, Sinan Obaidat

Graduate Theses and Dissertations

Sampling plans are statistical process control (SPC) tools used mainly in production processes. They are employed to control processes by monitoring the quality of produced products and alerting for necessary adjustments or maintenance. Sampling is used when an undesirable change (shift) in a process is unobservable and needs time to discover. Basically, the shift occurs when an assignable cause affects the process. Wrong setups, defective raw materials, degraded components are examples of assignable causes. The assignable cause causes a variable (or attribute) quality characteristic to shift from the desired state to an undesired state.

The main concern of sampling is …

Models For Data Analysis In Accelerated Reliability Growth, Cesar Alexander Ruiz Torres

Graduate Theses and Dissertations

This work develops new methodologies for analyzing accelerated testing data in the context of a reliability growth program for a complex multi-component system. Each component has multiple failure modes and the growth program consists of multiple test-fix stages with corrective actions applied at the end of each stage. The first group of methods considers time-to-failure data and test covariates for predicting the final reliability of the system. The time-to-failure of each failure mode is assumed to follow a Weibull distribution with rate parameter proportional to an acceleration factor. Acceleration factors are specific to each failure mode and test covariates. We …

Design And Optimization Of Multichip Gan Module Enabling Improved Switching Performance, Asif Imran Emon

Graduate Theses and Dissertations

Wide bandgap semiconductors (SiC & GaN) due to their enhanced performance and superior material properties compared to traditional silicon power devices have become the ultimate choice for future high-performance power electronics energy conversion. GaN high electron mobility transistor (HEMT) offers very fast switching capability enabling the designer to push switching frequency to the MHz range. Traditional device packaging becomes a limiting factor in fully harnessing the benefits offered by these advanced power devices, and thus, improved and advanced packaging structures are a must to bridge the gap between GaN devices and their applications. A co-design, co-optimization method has been followed …

Development Of A Reference Design For A Cyber-Physical System, Nicholas Paul Blair

Graduate Theses and Dissertations

The purpose of this thesis is to develop a reference design to assist in the selection of security practices in power electronics design. A prototype will be developed from this reference design for evaluation. This evaluation will include a brief cost/benefit analysis to gauge the efficacy of implementing each layer of security throughout the power electronics design process. This thesis will also describe the obstacles and effectiveness of integrating a Trusted Platform Module (TPM) into a cyber-hardened grid-connected device. The TPM device is a secured crypto processor that assists in generating, storing, and restricting the use of cryptographic keys. The …

On The Seismic Performance Of Skewed Special Moment Frame Reduced Beam Section Connections, Damaso Daniel Dominguez

Graduate Theses and Dissertations

Special Moment Frames (SMFs) are frequently used in high seismic areas for architecturally constrained designs, as they provide lateral system stiffness without the use of braces which often obstruct views and architectural features. Reduced beam section (RBS) connections are popular SMF connection details developed following the Northridge earthquake to limit brittle fractures within connection welds. Current American Institute of Steel Construction (ASIC) provisions (i.e. AISC 341-16) provide prequalified SMF RBS connection details (including welding requirements); however, all prequalified details only consider orthogonal connections between the beam and column. This dissertation investigates the effect of adding skew within SMF RBS connections …

Development Of Vs Profiles And Site Periods In The Mexico City Basin, Landon Joel Woodfield

Graduate Theses and Dissertations

This study presents dynamic site characterization measurements at 25 sites within the Mexico City Basin. The primary focus of the testing was along the western edge of the Mexico City Basin. At each site, active source Multi-channel Analysis of Surface Waves (MASW) arrays and passive source Microtremor Array Measurements (MAM) L-arrays and circular arrays were used to acquire dispersion data. Horizontal to Vertical Spectral Ratio (HVSR) data was collected to determine site periods at each location. These experimental dispersion data and site periods were fit using a joint inversion of Rayleigh and Love wave dispersion data and HVSR site period …

Numerically Modeling Steel Continuous Bridges For Early Age Concrete Deck Cracking, Abdul Aziz Nabil Salah

Graduate Theses and Dissertations

Early age bridge deck cracking is a common problem throughout the United States. Early age cracking develops shortly after the deck is poured. It reduces the serviceability and lifespan of bridges. Early age cracking can be typically attributed to either of two factors, 1) construction practices, and 2) shrinkage. The Arkansas Department of Transportation (ARDOT) has experienced early age bridge deck cracking. ARDOT currently specifies a sequence deck pour on most of their bridges; however, contractors prefer continuous deck pours because of ease and construction time. During the period of this TRC1903 research project, ARDOT has only approved a few …

Numerical Simulations Of Spread Foundations Supported On Stone Columns Using The Discrete Element Method, Anibal Enrique Santos Marin

Graduate Theses and Dissertations

The implementation of stone columns as a ground improvement technique has become more popular in geotechnical construction practice as a result of their ability to improve strength, stiffness and permeability characteristics of weak clayey soil deposits. There are several analytical and empirical approaches to estimate the bearing capacity of stone column foundation systems; however, there is notable variation in the performance of these existing methods when compared with full-scale experimental results. For very weak cohesive soils (i.e., undrained shear strength less than 15 kPa), the use of conventional stone columns becomes restricted because of the insufficient confinement that these types …

Best Practices For Asphalt Emulsion Particle Size Analyses Using A Coulter Counter, Logan P. Kiihnl

Graduate Theses and Dissertations

As asphalt pavements develop distresses, pavement preservation, maintenance, and rehabilitation treatments are used to mitigate distresses and extend the life of the pavement. Many of these treatments utilize asphalt emulsion. Previous research has linked particle size to material properties including viscosity and storage stability. General statements have also been made about particle size influencing emulsion performance while other researchers have identified a trend between particle size and prime coat penetration. Even though literature discusses the importance of particle size, there is little guidance on the best practices of asphalt emulsion particle size analyses, specifically with a Coulter counter.

Data collected …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …

Simulation Modeling Of Cross-Dock And Distribution Center Based Supply Chains, Ghewa Al Chall

Graduate Theses and Dissertations

Companies are implementing new strategies to meet the customer requirements in terms of quality, timing, and cost. One of these strategies is cross-docking, which can be defined as the process of consolidating the products coming from different suppliers, but having the same destination, with minimal handling and almost no storage between loading and unloading of the goods. The purpose of this research is to investigate the benefits of having a cross-docking facility in a supply chain. In this research, we focus on developing discrete event simulation models using the opensource Java Simulation Library (JSL). Also, we work on augmenting an …

The Release, Transport, And Utilization Of Phosphorus From Bed-Sediments: A Study Of A Eutrophic Littoral Cove On Beaver Lake In Northwest Arkansas, James A. Mccarty

Graduate Theses and Dissertations

Eutrophication of surface waters not only impacts the environment but also water treatment processes, the most significant of which is from the effects of algae. During peak algal growth in many southern U.S. reservoirs, inflows that bring nutrients are at an annual minimum, and phosphorus released from bed-sediments is trapped in the hypolimnion. Littoral areas, described as the most productive zone of the lake, may be a possible source of phosphorus that fuels algal growth in the reservoir. I studied an isolated shallow cove in the War Eagle Creek arm of Beaver Lake in Northwest Arkansas to measure, quantify, and …

A Virtual Space Vectors Based Model Predictive Control For Three-Level Converters, Waleed Saad S. Alhosaini

Graduate Theses and Dissertations

Three-phase three-level (3-L) voltage source converters (VSC), e.g., neutral-point clamped (NPC) converters, T-type converters, etc., have been deemed to be suitable for a wide range of medium- to high-power applications in microgrids (MGs) and bulk power systems. Compared to their two-level (2-L) counterparts, adopting 3-L VSCs in the MG applications not only reduces the voltage stress across the power semiconductor devices, which allows achieving higher voltage levels, but also improves the quality of the converter output waveforms, which further leads to considerably smaller output ac passive filters.

Various control strategies have been proposed and implemented for 3-L VSCs. Among all …

Improvement Of Geometric Quality Inspection And Process Efficiency In Additive Manufacturing, Yu Jin

Graduate Theses and Dissertations

Additive manufacturing (AM) has been known for its ability of producing complex geometries in flexible production environments. In recent decades, it has attracted increasing attention and interest of different industrial sectors. However, there are still some technical challenges hindering the wide application of AM. One major barrier is the limited dimensional accuracy of AM produced parts, especially for industrial sectors such as aerospace and biomedical engineering, where high geometric accuracy is required. Nevertheless, traditional quality inspection techniques might not perform well due to the complexity and flexibility of AM fabricated parts. Another issue, which is brought up from the growing …

Elucidating Basis Of Rice Discoloration And Developing Prevention Strategies, Zeinab Mohammadi Shad

Graduate Theses and Dissertations

Economically, discolored rice kernels have less market value, which can seriously impact farm net profit. The reasons for rice discoloration during storage have not been studied extensively and many questions remain. Therefore, the primary goal of this study was to improve understanding of the role and contributions of storage practices on rice quality degradation and discoloration. In this study, three rice cultivars including XL753 (hybrid), Roy J (pureline), and Titan were assessed for changes in quality and microbial kinetics. The rice samples at a high moisture content (MC) of 21% w.b. and a low MC of 16% were stored at …