Engineering Commons^™

Investigating The Factors Impacting The Success Of Immiscible Carbon Dioxide Injection In Unconventional Shale Reservoirs: An Experimental Study, Sherif M. Fakher

Doctoral Dissertations

"Unconventional shale reservoirs are currently gaining significant interest due to the huge hydrocarbon volumes that they bear. Enhanced oil recovery (EOR) techniques have been suggested to increase recovery from shale reservoirs. One of the most promising EOR methods is gas EOR (GEOR), most notably carbon dioxide (CO₂). Not only can CO₂ increase oil recovery by interacting with the oil and the shale, but it has also been shown to adsorb to the shale rock and thus is effective in both EOR applications and also carbon storage purposes. This research aims to experimentally investigate several of the interactions …

Observer-Based Event-Triggered And Set-Theoretic Neuro-Adaptive Controls For Constrained Uncertain Systems, Abdul Ghafoor

Doctoral Dissertations

"In this study, several new observer-based event-triggered and set-theoretic control schemes are presented to advance the state of the art in neuro-adaptive controls. In the first part, six new event-triggered neuro-adaptive control (ETNAC) schemes are presented for uncertain linear systems. These comprehensive designs offer flexibility to choose a design depending upon system performance requirements. Stability proofs for each scheme are presented and their performance is analyzed using benchmark examples. In the second part, the scope of the ETNAC is extended to uncertain nonlinear systems. It is applied to a case of precision formation flight of the microsatellites at the Sun-Earth/Moon …

Microgrid Design, Control, And Performance Evaluation For Sustainable Energy Management In Manufacturing, Md. Monirul Islam

Doctoral Dissertations

"This research studies the capacity sizing, control strategies, and performance evaluation of the microgrids with hybrid renewable sources for manufacturing end use customers towards a distributed sustainable energy system paradigm. Microgrid technology has been widely investigated and applied in commercial and residential sector, while for manufacturers, it has been less explored and utilized. To fill the gap, the dissertation first proposes a cost-effective sizing model to identify the capacities as well as control strategies of the components in microgrids considering a commonly used energy tariff, i.e., Time of Use (TOU). Then, the sizing model is extended by integrating control strategies …

Evaluation Of The Performance Of Different Polymer Gel Systems As An In-Depth Gel Treatment Using Numerical Simulation, Tariq K. Khamees

Doctoral Dissertations

"Oil production from heterogeneous and naturally fractured reservoirs are usually hindered due to the presence of high-permeability streaks and natural fractures networks. Oil production could be more lowered if there is a crossflow from the high- to the low-permeability layers and high mobility ratio. These problems are called conformance problems and the treatment is called conformance improvement technologies (CITs). The aims of CIT is to correct the heterogeneity of the reservoir and to lower the unfavorable mobility ratio. These technologies are leading to the diversion of post-treatment water into the low-permeability layers and to increase the viscosity of the displacing …

The Combined Toxic Effect Of Nanoparticles And Lead In The Presence Of Algae (Raphidocelis), Xuesong Liu

Doctoral Dissertations

"The elevated toxicity of toxic metals in the presence of nanoparticles (NPs) has raised significant concerns on the NP environmental safety. This research focuses on the impact of environmental conditions, specifically algae, on this type of toxicity. An indicator aquatic organism, Ceriodaphnia dubia (C. dubia), was used to examine the combined toxicity and toxicity mitigation from algae by monitoring its 24-h mortality. Four papers are included in this research, which focus on four aspects of the combined toxicity and the corresponding algae (Raphidocelis) impact. The first paper examines the algae impact on the combined toxicity of …

Novel Approaches For Reliable And Efficient Circuit Design, Prashanthi Metku

Doctoral Dissertations

"In this research work, a suite of approaches are presented to improve reliability of 3D heterogeneous processors (3DHP) and to reduce the area overhead of asynchronous designs. This work is primarily divided into two parts. In the first part, we present an approach for improving reliability in 3DHP. Typically, in 3DHP, thermal hotspots introduce spatial and temporal variability that results in wide bit error variation in DRAM dies. To address this issue multi- path BCH decoder is introduced. Based on the thermal gradient data generated by on-chip temperature sensors, the proposed methodology specializes in adaptively estimating the number of errors …

Strengthening Qc Relaxations Of Optimal Power Flow Problems By Exploiting Various Coordinate Changes, Mohammad Rasoul Narimani

Doctoral Dissertations

"Motivated by the potential for improvements in electric power system economics, this dissertation studies the AC optimal power flow (AC OPF) problem. An AC OPF problem optimizes a specified objective function subject to constraints imposed by both the non-linear power flow equations and engineering limits. The difficulty of an AC OPF problem is strongly connected to its feasible space's characteristics. This dissertation first investigates causes of nonconvexities in AC OPF problems. Understanding typical causes of nonconvexities is helpful for improving AC OPF solution methodologies.

This dissertation next focuses on solution methods for AC OPF problems that are based on convex …

Experimental And Modeling Studies Using Packed Bed Reactors: Liquid Phase Ethylene Production By Hydrogenation Of Acetylene, Humayun Shariff

Doctoral Dissertations

"Gas-phase catalytic hydrogenation of acetylene to produce ethylene, commonly practiced in industries, has green oil formation, which leads to catalyst deactivation and sometimes reactor runaway risks due to high exothermicity. To overcome these issues as well as to increase the selectivity and conversion, liquid-phase hydrogenation of acetylene was investigated in packed bed reactors (PBR) using a commercial catalyst. The reactor performance of two-phase flow PBRs was assessed experimentally complemented by a validated mathematical model at different scales.

The selective hydrogenation of acetylene in the liquid phase over a commercial 0.5 wt% Pd/Al₂O₃ catalyst was investigated in a …

Minimizing The Detrimental Effects Of Hydro-Peaking On Riverbank Instability: The Lower Osage River Case, Wesam Sameer Mohammed-Ali

Doctoral Dissertations

"The fluctuation of water level downstream from dams due to hydropower flow releases negatively affects the riverbank stability. Therefore, this research aims to examine the feasibility of using an optimization technique to mitigate the riverbank instability resulting from the outflow variation of hydropower plants. The effects of the water releases from the Bagnell Dam were investigated by computing a series of safety factors for 78 cross sections along the 81-mile stretch of the lower Osage River in relation to outflow events by using the integrated BSTEM model incorporated into the HEC-RAS model. The 1-D sediment transport and unsteady flow in …

Design Of X-Ray Source For Real-Time Computed Tomography, Wesley William Tucker

Doctoral Dissertations

"The reduction of motion blur in computed tomography (CT) drives the current research for multisource CT. Due to their compact nature, the current multisource systems utilize stationary angled anodes. Unfortunately, these configurations neither simplify the imaging geometry, nor satisfy the need for managing the high thermal loads demanded by real-time CT (30 acquisition frames per second). To add to the current field of knowledge, two x-ray tube concepts are presented in this dissertation. First, a simulation of transient thermal analysis was performed on a compact transmission-type x-ray tube anode operating in pulse-mode. A correlation was found between deposited beam power …

Characterization And Recyclability Of 304l Stainless Steel Powder For Use In The Selective Laser Melting Process, Austin Taylor Sutton

Doctoral Dissertations

"Powder-bed fusion refers to a subset of additive manufacturing (AM) methods which successively melts and solidifies selected regions within a powder bed on a layer-by-layer basis to construct components directly from computer-aided design files. Laser Powder-Bed Fusion (L-PBF) is a process among the powder-bed fusion techniques that utilizes a laser to consolidate particles into a material with little porosity. During the L-PBF process, the large energy input from the laser causes the production of ejecta in the form of laser spatter and condensate, both of which have the potential to settle in the surrounding powder bed compromising its reusability. In …

Impact Of Turbulence Models And Shape Parameterization On Robust Aerodynamic Shape Optimization, Aslihan Vuruskan

Doctoral Dissertations

"Aerodynamic design optimization is typically performed at fixed flight conditions, without considering the variation and uncertainty in operating conditions. The objective of robust aerodynamic optimization is to design an aerodynamic configuration, which will keep its optimum performance under varying conditions such as the speed of aircraft. The primary goal of this study was to investigate the impact of turbulence models used in RANS simulations on the 2-D airfoil and 3-D wing designs obtained with gradient-based deterministic and robust optimization in transonic, viscous, turbulent flows. The main contribution of this research to the aerodynamic design area was to quantify the impact …

System Si/Pi Modeling And Analysis, Biyao Zhao

Doctoral Dissertations

"A physics-based circuit modeling methodology for 3D IC/packages is proposed here. The method is based on partial element equivalent circuit (PEEC) and layered Green's function (LGF). The LGFs are calculated from discrete complex image method (DCIM) with three terms, direct coupling, complex images, and surface wave, extracted to analyze the wave behavior. The dominate terms for LGFs are analyzed for four stack-ups in 3D IC/packages. Analytical formulas that include the contribution of complex images are proposed for partial capacitance calculation, with the complex image extracted from LGFs. A chip PDN geometry is used to illustrate the use of LGF in …

Frequency Selective Surface-Based Sensing: Theory And Applications, Mahboobeh Mahmoodi

Doctoral Dissertations

"Frequency selective surfaces (FSS) are periodic arrays of resonant elements with a specific (resonant) reflection/transmission response when illuminated by electromagnetic energy. FSSs have been utilized for different applications such as spatial filters, reflectors, lenses, radomes, and more recently, as sensors. FSS-based sensors have shown potential for numerous applications in structural health monitoring such as crack detection, concurrent strain and temperature sensing, normal and shear strain sensing, inspection of layered structures, etc. As FSS-based sensing is largely undeveloped, there are many critical aspects that must be fully understood before this sensing approach can be fully utilized. Therefore, the goal of this …

Trajectory Control Of A Wheeled Robot Using Interaction Forces For Intuitive Overground Human-Robot Interaction, George Leno Holmes Jr.

Doctoral Dissertations

"Effective and intuitive physical human robot interaction (pHRI) requires an understanding of how humans communicate movement intentions with one another. It has been suggested that humans can guide another human by hand through complex tasks using force information only. However, no clear and applicable paradigm has been set forth to understand these relationships. While the human partner can readily understand and adhere to this expectation, it would be difficult for anyone to explain their intuitive motions with strict rules, algorithms, or steps. Uncovering such a procedural framework for the control of robotic systems to execute expected performance simply from force …

Modeling A Nuclear Research Reactor And Radiation Dose Estimation In An Accident Scenario, Abdulaleem Abdulmajeed Bugis

Doctoral Dissertations

“A detailed, flexible three-dimensional (3D) model of the Missouri S&T Reactor (MSTR) with a heterogeneous core geometry was developed using the Standardized Computer Analyses for Licensing Evaluation (SCALE). A Graphical User Interface (GUI) was developed for SCALE, which allows the user to generate an input file automatically. The SCALE model was validated with a Monte Carlo N-Particle Transport (MCNP) model of the MSTR. The validation process was based on the criticality calculations using the Criticality Safety Analysis Sequence (CSAS6). Three geometrical models were examined. The SCALE model that has the full detailed geometry showed a good agreement with the MCNP …

Experimental Study On A Novel Eor Method -- Polymeric Nanogel Combined With Surfactant And Low Salinity Water Flooding To Enhance Oil Recovery, Mustafa M. Almahfood

Doctoral Dissertations

“Extracting higher amounts of oil from current reservoirs is a necessity for the oil industry to enhance their profitability and sustainability. The desire to recover more oil from the existing reservoirs has led to a growing interest of nanoparticle application in enhanced oil recovery (EOR). However, most researchers have focused on the evaluation and surface modification of non-deformable nanoparticles. This dissertation evaluates the potential of deformable nanogel particles as an EOR material when they are combined with two other promising technologies - surfactant and low salinity water floodings. The particle size distribution, ζ-potential and interfacial tension were measured for a …

Development Of Radiation Transport Techniques For Modelling A High-Resolution Multi-Energy Photon Emission Tomography System, Seth Kilby

Doctoral Dissertations

”Nondestructive characterization techniques such as gamma tomography represent powerful tools for the analysis and quantification of physical defects and radionuclide concentrations within nuclear fuel forms. Gamma emission tomography, in particular, has the ability to utilize the inherent radiation within spent nuclear fuel to provide users with information about the migration and concentration of fission and activation products within the fuel form. Idaho National Laboratory is interested in using this technology to analyze new nuclear fuel forms for potential use in next generation nuclear reactors. In this work, two aspect of the system are analyzed. The first is a semi-analytic radiation …

Development Of Tools For Water Management In The Hatra Watershed (Northwestern Iraq) Using Satellite Technologies, Majid S. Mohamod

Doctoral Dissertations

“All around the world the demand for water is increasing, especially in arid and semi-arid regions, including Iraq which subject to continuous desertification that is worsening, more importantly the Jezira region in northwestern Iraq. Thus, it’s crucial to have a better strategy for water management. One of these strategies is to promote groundwater recharge for restoring the aquifer depletion. The successful groundwater recharge is limited by some potential data such as the annual water budge and precipitation measurements. The atomospheric and hydrological observations are limited by sparse population which tends to be less in arid and semi-arid regions. Therefore, an …

Integrating Resilience Into Military Infrastructure Mission Assurance Assessments And Decision Making, John Richards

Doctoral Dissertations

“This research created the Mission Assurance Resilience Matrix, a decision framework that integrates existing infrastructure assessment methods with emerging resilience research to model resilience under uncertainty as part of a detailed infrastructure management system. This framework enables military decision makers to easily visualize deficiencies in infrastructure resilience and assess where to most efficiently allocate resources. This research further extends results by including modules on training and education as a component of the scope of work.

There are three significant contributions of this research. The first identifies the gaps of how and where modeling under uncertainty, infrastructure systems management, and resilient …

Stress Analysis Of Operating Gas Pipeline Installed By Horizontal Directional Drilling And Pullback Force Prediction During Installation, Hongfang Lu

Doctoral Dissertations

With the development of the natural gas industry, the demand for pipeline construction has also increased. In the context of advocating green construction, horizontal directional drilling (HDD), as one of the most widely utilized trenchless methods for pipeline installation, has received extensive attention in industry and academia in recent years. The safety of natural gas pipeline is very important in the process of construction and operation. It is necessary to conduct in-depth study on the safety of the pipeline installed by HDD method.

In this dissertation, motivated by the following considerations, two aspects of HDD are studied. First, through the …

Application Of Halloysite Nanotubes In Bone Disease Remediation And Bone Regeneration, Yangyang Luo

Doctoral Dissertations

Customized patient therapy has been a major research focus in recent years. There are two research fields that have made a significant contribution to realizing individualized-based treatment: targeted drug delivery and three-dimensional (3D) printing technology. With benefit from the advances in nanotechnology and biomaterial science, various drug delivery systems have been established to provide precise control of therapeutic agents release in time and space. The emergence of three-dimensional (3D) printing technology enables the fabrication of complicated structures that effectively mimic native tissues and makes it possible to print patient-specific implants. My dissertation research used a clay nanoparticle, halloysite, to develop …

Feature Space Modeling For Accurate And Efficient Learning From Non-Stationary Data, Ayesha Akter

Doctoral Dissertations

A non-stationary dataset is one whose statistical properties such as the mean, variance, correlation, probability distribution, etc. change over a specific interval of time. On the contrary, a stationary dataset is one whose statistical properties remain constant over time. Apart from the volatile statistical properties, non-stationary data poses other challenges such as time and memory management due to the limitation of computational resources mostly caused by the recent advancements in data collection technologies which generate a variety of data at an alarming pace and volume. Additionally, when the collected data is complex, managing data complexity, emerging from its dimensionality and …

Electrolytic Metallization Of Halloysite Nanotubes And Antimicrobial Applications, Ahmed Humayun

Doctoral Dissertations

Due to increased reports of infections and biofouling arising from the use of invasive medical devices, novel antimicrobial agents with suitable anti-biofouling properties are critically needed. Transition metals exhibit substantial antimicrobial activity; however, their use is limited because of their inherent toxicity to eukaryotic cells. In this regard, naturally occurring halloysite clay nanotubes (HNTs) show significant promise. HNTs possess a high surface area for adsorption while its hollow lumen can be used for loading different materials.

Herein, we demonstrate an electrolytic method for generating and depositing metal nanoparticles (NPs) on the HNTs outer surface and we propose an optimized method …

A Multicarrier Technique For Monte Carlo Simulation Of Electrothermal Transport In Nanoelectronics, Tyler J. Spence

Doctoral Dissertations

The field of microelectronics plays an important role in many areas of engineering and science, being ubiquitous in aerospace, industrial manufacturing, biotechnology, and many other fields. Today, many micro- and nanoscale electronic devices are integrated into one package. e capacity to simulate new devices accurately is critical to the engineering design process, as device engineers use simulations to predict performance characteristics and identify potential issues before fabrication. A problem of particular interest is the simulation of devices which exhibit exotic behaviors due to non-equilibrium thermodynamics and thermal effects such as self-heating. Frequently, it is desirable to predict the level of …

Organically Modified Inorganic Nanoparticles For Halochromic Ionophores And Nucleic Acids, William Johnston

Doctoral Dissertations

In this dissertation, four nanoparticle reaction schemes were developed as substrates for halochromic dyes or nucleic acids. The reaction schemes include the use of two substrates: silica nanoparticles and halloysite nanotubes. The protocols can incorporate silica (SiO2) nanoparticles and halloysite aluminosilicate (AlO2SiO2) nanotubes due to the presence of silane groups on the surface of either substrate. The reaction schemes are presented along with detailed protocols which were written to facilitate both reproducibility and to serve as an aid to further study and for easy modification of the protocol to suit a researcher's needs. The data is discussed in the materials …

Design, Microfabrication And Characterization Of Concentric Gold Nanoring Electrode For Neurochemical Sensing, Haocheng Yin

Doctoral Dissertations

Nanoelectrodes have become widely used in electrochemical sensing in recent decades. When compared to microelectrodes, it has many unique advantages such as high signal to noise ratio, small sample volume requirement, and lower detection limits.

This work reports on the microfabrication and characterization of a gold nanoring electrode (Au NRE) patterned on top of a silicon (Si) micropillar. An NRE of 165  10 nm in width was micropatterned on 4.6  1 µm diameter  17.5  2.5 µm long Si micropillar with an intervening 50 nm thick hafnium oxide insulating layer. Scanning electron microscopy and energy dispersive spectroscopy …

Increasing The Functionality Of Additive Manufacturing Through Atmospheric Microplasma And Nanotechnology, Alexander Jon Ulrich

Doctoral Dissertations

Additive Manufacturing (AM) has been changing the manufacturing landscape for the last 20 years. As the interest and demand for both polymer and metal-based 3D printing has grown, the materials and machines used have increased in capabilities. Despite the growth and advancement, there are still a large number of improvements that can be made to add functionality to 3D printers. Metal AM, a subcategory of 3D printing, has garnered much attention among industrial applications with large companies such as General Electric trying to implement the technology to increase innovative designs for motors. Some of the limitations on AM have to …

Development Of A Low Profile, Endoscopic Implant For Long Term Brain Imaging, Benjamin Scott Kemp

Doctoral Dissertations

The increased public awareness of concussion and traumatic brain injury has motivated continued research into the brain, its functions, and especially its response to injury, with a focus on improving the brain’s repair capabilities. However, due to the critical nature of the tissue, it is currently difficult for researchers to acquire high resolution images below the cortex without sacrificing a lab animal. Sacrificing an animal greatly reduces the amount of data that can be obtained from it, making longitudinal studies unappealing or unfeasible because a large number of animals is needed to obtain useful data over multiple time points. Additionally, …

Migration And Electropolymerization Of Methyl Methacrylate In Hardened Cement Paste Via Electrokinetic Treatment, Xi Xie

Doctoral Dissertations

Porous concrete structures are susceptible to the intrusion of chemical species, such as sulfates, chlorides, and carbon dioxide. Many technologies have been developed to repair or rehabilitate damaged concrete. These include cathodic protection, corrosion inhibitor addition, or the use of coatings and sealers. In recent years, a developing technology, electrokinetic nanoparticle treatment, has been shown to reduce concrete porosity, increase strength, promote corrosion resistance, and extend durability. This dissertation was conducted to explore a novel treatment to reduce the porosity of concrete via the application of electrokinetic transportation and electro-initiated polymerization of methyl methacrylate (MMA).

Potassium persulfate (PSP) was used …