Engineering Commons^™

Effects Of Froude Scaling On Velocity-Induced Vortices In Physical Models, Michael S. Budge

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Utah Water Research Laboratory at Utah State University proposes to examine further a little known issue frequently seen in research conducted. The Utah Water Research Lab frequently conducts physical model studies of hydraulic structures for organizations around the world during the design process. These studies allow engineers to determine potential design revisions though simulations of operations including flood flows. Often, vortices, or whirlpools, occur in these models. Vortices are common occurrences at intakes in hydraulic structures such as dams and pump sumps. They can be detrimental to the operation and efficiency of these structures.

The purpose of this work …

Spacecraft Guidance Techniques For Maximizing Mission Success, Shane B. Robinson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Traditional spacecraft guidance techniques have the objective of deterministically minimizing fuel consumption. These traditional approaches to guidance are developed independently of the navigation system, and without regard to stochastic effects. This work presents and demonstrates a new approach to guidance design. This new approach seeks to maximize the probability of mission success by minimizing the variance of trajectory dispersions subject to a fuel consumption constraint. The fuel consumption constraint is imposed by formulating the dynamics in terms of a steering command, and placing a constraint on the final time. Stochastic quadratic synthesis is then used to solve for the nominal …

Numerical Examination Of Flux Correction For Solving The Navier-Stokes Equations On Unstructured Meshes, Dalon G. Work

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This work examines the feasibility of a novel high-order numerical method, which has been termed Flux Correction. This is accomplished by comparing it against another high-order method called Flux Reconstruction. These numerical methods are used to solve the Navier-Stokes equations, which govern the motion of fluid flow. High-order numerical methods, or those that demonstrate a third-order and higher solution error convergence rate, are rarely used on unstructured meshes when solving fluid problems. Flux Correction intends to make high-order accuracy available to the larger world of Computational Fluid Dynamics in a simple and effective manner. The advantages and disadvantages of the …

Excimer-Monomer Switching Molecular Beacon: The Study On Synthetic Cryptosporidium Dna Detection, Thermodynamics, And Magnesium Effects, Michael L. Davis

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The purpose of this study is to quantify and determine the binding of a molecular DNA probe or molecular beacon used in the detection of a known waterborne pathogen Cryptosporidium parvum. The objectives of this study are to determine the stability, sensitivity, and selectivity of the molecular beacon in detecting synthesized Cryptosporidium DNA sequences. The designed probe is based on a two-fluorophore system that is different than similar molecular beacons that utilize a fluorophore and quencher detection method. A comparative study between the two probes was also performed to demonstrate enhanced selectivity of the fluorophore based molecular beacon. Magnesium …

Nonlinear Weir Hydraulics, Mitchell R. Dabling

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A hydraulically undersized control structure (i.e., an emergency dam spillway) could result in water overtopping a dam or riverbanks. To increase hydraulic capacity and reduce flooding risk, nonlinear weirs are being used to replace undersized linear weirs during control structure rehabilitation. The complex geometry of a nonlinear weir creates an infinite number of designs and three-dimensional flow patterns. This study investigates four subjects to further knowledge on two types of nonlinear weir, the piano key and labyrinth.

Weir submergence is a condition when the downstream water level of a weir exceeds the weir crest elevation, and can influence the head-discharge …

Uniform Temperature Predictions And Temperature Gradient Effects On I-Girder And Box Girder Concrete Bridges, Edyson Rojas

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Federal Highway Administration (FHWA) created the Long-Term Bridge Performance (LTBP) program with the objective of acquiring quality scientific data for in-service bridge performance throughout the United States. This information will be used to improve the practices of bridge design and maintenance. To accomplish this objective, a variety of sensors were installed on a bridge south of Sacramento, California and a bridge near Perry, Utah. Data from the sensors is constantly gather and analyzed.

This research analyzed the data from the temperature sensors in order to investigate the effect of temperature changes in the California and Utah bridges over a …

Innovative Payloads For Small Unmanned Aerial System-Based Personal Remote Sensing And Applications, Austin M. Jensen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Remote sensing enables the acquisition of large amounts of data, over a small period of time, in support of many ecological applications (i.e. precision agriculture, vegetation mapping, etc.) commonly from satellite or manned aircraft platforms. This dissertation focuses on using small unmanned aerial systems (UAS) as a remote sensing platform to collect aerial imagery from commercial-grade cameras and as a platform to track radio-tagged fish. The small, low-cost nature of small UAS enable remotely sensed data to be captured at a lower cost, higher spatial and temporal resolution, and in a more timely manner than conventional platforms. However, these same …

Weir-Baffled Culvert Hydrodynamics Evaluation For Fish Passage Using Particle Image Velocimetry And Computational Fluid Dynamic Techniques, Mohanad A. Khodier

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Due to a recent increase in environmental awareness regarding fish passage through hydraulic structures, including culverts, an evaluation of passage of wild brown trout through a weir-baffled, prototype-scale culvert, was conducted under a variety of culvert slopes and discharge conditions. The influence of the fish sample population and the lengths of the individual fish on passage rates were investigated. The data showed that the fish sample size of 25 per test was sufficiently large to minimize sample size dependency. Fish behavior, including resting/staging zone locations, while traversing the culvert was observed and reported. Two preferable resting zones for the fish …

Prediction Of Climate Change Effects On Streamflow Regime Important To Stream Ecology, Sulochan Dhungel

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Streamflow is expected to change with climate change, but a general understanding of how climate change will affect the characteristics of streamflow important to stream ecosystems is lacking. This thesis focused on specific characteristics of streamflow, or the streamflow regime, that are important to stream ecosystems. The need to evaluate the potential impacts of climate change on stream ecosystems makes it important to study how streamflow regime may change. This work has identified 16 characteristics of daily streamflow time series that quantify the patterns and span the aspects of streamflow regimes important for stream ecosystems. Principal component analysis objectively identified …

The Effects Of Laser Etching On Biocompatability And Mechanical Properties Of Polyetheretherketone, Andrew I. Deceuster

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Polyetheretherketone (PEEK) is a Federal and Drug Administration (FDA) approved biomaterial that has been used as an orthopedic implant material due to its inherent properties. Laser etching has become a popular means to create identification markers on the individual implants as required by the FDA. The interaction of laser energy with polymeric materials could potentially cause changes in the material's biocompatibility and mechanical properties. The objective of this study was to determine the effect of laser energy on the biocompatibility and mechanical properties of implantable PEEK by measuring contact angle, micro-tensile testing, nite-element modeling (FEM), and biocompatibility testing according to …

Nano-Scale Thermal Property Prediction By Molecular Dynamics Simulation With Experimental Validation, Kyle S. Horne

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A new type of laser diode, called a quantum cascade laser (QCL), was developed in the mid 1990's. These new lasers have many applications including industrial emissions analysis and explosives detection. Like many solid-state devices, they work better at cooler temperatures, but operating the device generates heat; this results in a cooling problem if the device is to operate continuously at high-power. To improve this situation, a better understanding of how heat leaves the laser diode is needed. The thermal conductivity of a material is a measure of how quickly heat will leave it. In this work, two approaches are …

Expert Vs. Novice: Problem Decomposition/Recomposition In Engineering Design, Ting Song

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The purpose of this research was to investigate the design behavior. A commonly used design strategy called “problem decomposition and recomposition” was the focus of the study. Dyads of engineering experts, dyads of engineering seniors, and dyads of engineering freshmen completed an engineering design challenge within an hour. The entire design process was video and audio recorded. After the design session, participants participated in a group interview.

The conversation and behavior from the design were transcribed, segmented, and coded. Two coding systems including the FBS ontology and “levels of the problem” were used in this study. A series of statistical …

Bridging The Nano- And Macro-Worlds: Thermal Property Measurement Using Thermal Microscopy And Photothermal Radiometry – Application To Particle-Irradiation Damage Profile In Zirconium Carbide, Colby Bruce Jensen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Multiscaled experimental investigations of heat transfer from nanoscales to macroscales are requisite to progress in energy technologies. In nuclear applications, material properties can undergo significant alteration due to destructive interaction with irradiating particles at microstructural levels that affect bulk properties. This study expands the current knowledge base regarding thermal transport in ion-irradiated materials through the use of a multiscaled experimental approach using four complementary thermal wave methods. For the first time, the in-depth thermal conductivity profile of an ion-irradiated sample is measured directly.

Experimental Studies Of Delta Wing Parameters In Open Channel Raceway Determined Via Validated Computational Fluid Dynamics, Cole David Blakely

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A promising feedstock for biofuels is microalgae. The most economical means of cultivating microalgae is via open raceway ponds. However, a large gap in economic feasibility exists between algae-based biofuels and traditional petroleum fuels. Recent research at Utah State University has focused on increasing biomass growth by implementing Delta Wings (DWs). DWs are placed facing the incoming flow, with a 40 degree angle of attack to create large vortices which travel downstream. The trailing vortices increase vertical mixing, which in turn increases algal growth.

Past researchers at USU quantified vertical mixing with new metrics, optimized various raceway operating conditions, and …

Causes And Countermeasures For Nappe Oscillation: An Experimental Approach, Aaron Allan Anderson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Weirs are commonly used as spillways to release flows from a reservoir. The freefalling jet on the downstream side of the weir is called the nappe. Under certain hydraulic conditions, determined mainly by the size, design, and construction of the weir, nappe oscillation, otherwise known as nappe vibration, can occur. Characteristics of this dynamic behavior include excessive acoustic energy manifested as sound pressure waves and lowfrequency noise accompanied by horizontal waves or banding on the nappe. Mitigation of this process may be required, especially if the weir operates in close proximity to occupied structures. Instability of water jets moving through …

Uncertainty Quantification Of Photothermal Radiometry Measurements Using Monte Carlo Simulation And Experimental Repeatability, Austin Fleming

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Photothermal Radiometry is a common thermal property measurement technique which is used to measure the properties of layered materials. Photothermal Radiometry uses a modulated laser to heat a sample, in which the thermal response can be used to determine the thermal properties of layers in the sample. The motivation for this work is to provide a better understanding of the accuracy and the repeatability of the Photothermal Radiometry measurement technique. Through this work the sensitivity of results to input uncertainties will be determined. Additionally, using numerical simulations the overall uncertainty on a theoretical measurement will be determined.

The repeatability of …

Flexural, Shear, And Punching Shear Capacity Of Three 48-Year-Old Prestressed Lightweight Concrete Double-Tee Bridge Girders, Christopher S. Pettigrew

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Icy Springs Bridge in Coalville, Utah carries 2^nd South Street over the Weber River west of Interstate 80. The bridge is owned by Coalville City and was originally constructed in 1965 as a single-span 51-foot long bridge using prestressed concrete double-tee girders. In the fall of 2013 the original bridge was replaced with a new 80-foot long single span bridge using prestressed concrete decked bulb-tee girders. The original girders were salvaged and transported to the Systems, Materials, and Structural Health Lab (SMASH Lab) where a series of tests were performed to determine the total losses in the prestressing …

Impact Of Beaver Ponds On Stream Temperature And On Solar Radiation Penetration In Water, Camilla J. Snow

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Beaver dams alter streams characteristics in a way that promotes the diversity of aquatic species and provides a wide distribution of temperatures within beaver ponds. In order to quantify the spatial distribution of these temperatures, a process-based temperature model was developed for a beaver pond in Northern Utah. This model provided insight into the processes and characteristics that are driving these temperatures. Solar radiation is one of these processes that is often the primary driver of stream temperature. There is a need to develop methods to measure the fate of solar radiation within the water to better represent solar radiation …

Parasitic Layer-Based Reconfigurable Antenna And Array For Wireless Applications, Zhouyuan Li

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Antenna is one of the most important components in wireless systems since signal transmission and reception are conducted through the antenna interface. Therefore, the signal quality is highly affected by the properties of the antenna. Traditional antennas integrated in devices such as laptops or cell phones have fixed radiation properties and can not be changed to adapt to different environments. Thus the performance of thefwhole system will be negatively affected since the antenna will not operate in the optimum status in different environments. To solve this problem, reconfigurable antenna, which can dynamically change its operation frequency, radiation pattern, and polarization, …

Graphics Processing Unit-Based Computer-Aided Design Algorithms For Electronic Design Automation, Yiding Han

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The electronic design automation (EDA) tools are a specific set of software that play important roles in modern integrated circuit (IC) design. These software automate the design processes of IC with various stages. Among these stages, two important EDA design tools are the focus of this research: floorplanning and global routing. Specifically, the goal of this study is to parallelize these two tools such that their execution time can be significantly shortened on modern multi-core and graphics processing unit (GPU) architectures. The GPU hardware is a massively parallel architecture, enabling thousands of independent threads to execute concurrently. Although a small …

Reconfigurable Antennas For Public Safety And Wireless Gigabit Alliance Applications, Hema Swaroop Mopidevi

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The main goal of this research is to develop a new type of antenna, called reconfigurable antenna, which can replace multiple antennas required to enhance the effectiveness of a robust communication system. A reconfigurable antenna integrated with switching elements can dynamically change its properties, namely, frequency of operation, radiation pattern (the three-dimensional coverage of antenna), and polarization (the electrical orientation of the antenna). Depending on the requirement, a single antenna can function as multiple antennas, therefore, the name Multi-functional Reconfigurable Antenna (MRA). United States (US) Public Safety (PS) responders (police, fire-fighters, emergency medical services, etc.) can effectively respond to human-made …

Improving The Physical Processes And Model Integration Functionality Of An Energy Balance Model For Snow And Glacier Melt, Avirup Sen Gupta

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Hindu-Kush Himalayan region possesses a large resource of snow and ice, which acts as a freshwater reservoir for irrigation, domestic water consumption or hydroelectric power for billions of people in South Asia. Monitoring hydrologic resources in this region is challenging because of the difficulty of installing and maintaining a climate and hydrologic monitoring network, limited transportation and communication infrastructure and difficult access to glaciers. As a result of the high, rugged topographic relief, ground observations in the region are extremely sparse. Reanalysis data offer the potential to compensate for the data scarcity, which is a barrier in hydrological modeling …

Laboratory Modeling Of Erosion Potential Of Earthen Embankments In Contact With Open Bedrock Joints, Joseph T. Zaleski

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Earthen dams are often built into bedrock abutments and on bedrock foundations. Bedrock joints naturally occur in bedrock materials. These bedrock joints create voids for ground water to pass through. Historically earthen dams were sometimes built in direct contact with the bedrock joints, causing a contact point between the soil of the dam and the flowing water. It has been engineering practice to place grout into exposed bedrock joints for some time now. However, soil is not always cleaned out of bedrock joints before they are grouted, which leaves a weakness for water to push through.

The purpose of this …

Metabolic Modeling Of Spider Silk Production In E. Coli, Sarah Allred

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Spider silk has the potential to be a useful biomaterial due to its high tensile strength and elasticity. It is also biocompatible and biodegradable, making it useful for wound dressings and sutures, tissue and bone scaffolds, vessels for drug delivery, and ligament and tendon replacements. In some studies where spider silk has been used to grow cells, the silk has promoted more cell growth than the control. However, it is difficult to obtain the high volume of silk needed for these undertakings on a large scale. Spiders are territorial and cannibalistic, so they cannot be easily farmed. Therefore, spider silk …

Effect Of Poultry Litter Biochar On Saccharomyces Cerevisiae Growth And Ethanol Production From Steam-Exploded Poplar And Corn Stover, Oumou Diallo

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The use of ethanol produced from lignocellulosic biomass for transportation fuel offers solutions in reducing environmental emission and the use of non-renewable fuels. However, lignocellulosic ethanol production is still hampered by economic and technical obstacles. For instance, the inhibitory effect of toxic compounds produced during biomass pretreatment was reported to inhibit the fermenting microorganisms, hence there was a decrease in ethanol yield and productivity. Thus, there is a need to improve the bioconversion of lignocellulosic biomass to ethanol in order to promote its commercialization. The research reported here investigated the use of poultry litter biochar to improve the ethanol production …

Physical Layer Detection Of Hardware Keyloggers, Saptarshi Mallick

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This work addresses the problem of detecting devices which are stealthily attached to the computer for logging keystrokes from keyboards. These devices are known as hardware keyloggers (HKL). When an HKL is attached to the keyboard, certain electrical characteristics of the keyboard signal are altered. Based on these characteristics (features), differences have been identified in an accurate assertion was made about the presence of HKL.

The characteristics from which the differences were obtained were used to make distributions and compared with distance-measuring methods. An experiment was done to collect data from a number of keyboards and form two distributions (training …

A Platform For False Data Injection In Frequency Modulated Continuous Wave Radar, Ruchir Chauhan

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Radar is an acronym for RAdio Detection And Ranging. In general terms, it is a machine that uses radio waves for object-detection in its near periphery. It transmits radio waves in a known direction, which when intercepted by an obstruction/object are reflected by its surface and are received back at the radar system. The round trip delay time along with the known velocity of radio waves gives an accurate measurement of the distance of the object from the radar system. In a somewhat similar fashion, some radars are even capable of measuring the velocity of this object. Frequency-modulated continuous-wave (FMCW) …

Distribution Of Heavy Metals From Flue Gas In Algal Bioreactor, Katerine Napan

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Algae are microscopic organisms with a great potential to produce biomass and lipids at productivities several times higher than terrestrial crops. To grow, these organisms consume carbon dioxide (CO₂), a greenhouse gas. This gas, emitted primarily by power plants after coal burning, can be effectively used for algae production, thus resulting in CO₂ remediation and biomass beneficial utilization as feedstuff, industrial filler and biodiesel feedstock. However, since coal is a fuel mined from the earth’s crust, it contains heavy metals that are released during coal burning and inevitably enter the algal cultivation system, contaminating the water were …

Uncertainty Analysis Of Mechanical Properties From Miniature Tensile Testing Of High Strength Steels, Deepthi Rao Malpally

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This Miniature mechanical testing study is concerned with the use of miniature specimens to identify the mechanical properties of stainless steel Type 304, sensitized Type 304 and SA516 Grade 70 carbon steel as a viable replacement for the standard sized mechanical testing. The study aims at obtaining suitable specimen geometry and tensile testing procedure for miniature mechanical testing whose mechanical properties are comparable to that of conventional specimens of ASTM A370-10 of the same steel. All specimens are at and the gauge length cross section will be varied to obtain suitable geometry. The miniature tensile testing results are further validated …

Use Of Semi-Analytical Solutions To Examine Parameter Sensitivity And The Role Of Spatially Variable Stream Hydraulics In Transient Storage Modeling, Noah M. Schmadel

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Anticipating how stream water quality will respond to change, such as increased pollution or water diversions, requires knowledge of the main mechanisms controlling water and chemical constituent movement and a reasonable representation of those mechanisms. By deriving mathematical models to represent a stream system and collecting supporting field-based measurements, water quality response can be predicted. However, because each stream is unique and the movement of water and constituents is spatially and temporally complex, assessing whether the stream is appropriately represented and whether predictions are trustworthy is still a challenge within the scientific and management communities.

Building on decades of stream …