Engineering Commons^™

Evaluation And Modeling Of Electrodialysis For High-Recovery Brackish Water Desalination, Shahrouz Jafarzade Ghadimi

Open Access Theses & Dissertations

This research investigates the feasibility of desalination of brackish water with electrodialysis (ED), using laboratory testing and mathematical modeling. Several experiments were performed to characterize ion-specific transport and to evaluate tradeoffs between salinity removal and specific energy consumption. A 200 cm2 Ameridia ED stack was used to perform desalination experiments with real brackish groundwater from the Kay Bailey Hutchison desalination plant in El Paso, Texas, and the results showed limiting current density of 160 A/m2 for 5 cm/s. A higher conductivity reduction was observed for flow velocity of 5 cm/s compared to 13 cm/s. Ion transport selectivity (based on relative …

Evaluation Of Cyclo Olefin Polymer As Sabot Material For High-Density Projectiles, Estebanne Tarango

Open Access Theses & Dissertations

Assuring the integrity of spacecraft and its occupants are a priority in the field of space exploration. Micrometeoroids and orbital debris are one of the primary threats that affect spacecraft materials due to the high kinetic energies involved with hypervelocity impacts. Improvement of projectile launching capabilities prompts the investigation of adequate materials for the manufacturing of sabots able to carry high-density projectiles without catastrophic failure. Polycarbonate (PC) has been the chosen material by the Hypervelocity Team at White Sands Test Facility for sabots on the 0.50 caliber launcher; however, there is a material constraint when the projectile becomes significantly dense …

Design And Operability Of A Pressurized Oxy-Combustion System, Mehrin Chowdhury

Open Access Theses & Dissertations

Fossil fuel powers more than two-thirds of the world’s electricity, a significant share of which is derived from coal power plants. Despite coal being an abundant and energy-rich fuel, the major halt to its progress is greenhouse gas emissions. Greenhouse gases are detrimental to the environment. The search for clean fossil fuel leads to the oxy-combustion process. Oxy-fuel combustion produces sequestrable carbon dioxide as exhaust. Pressurization makes carbon capture more accessible and more energy-efficient. Pressurized oxy-combustion cycles can achieve theoretically high thermal efficiencies along with a 90% carbon capture rate. Additionally, the high energy density allows smaller turbomachinery and save …

The Study Of Non-Permanent Tattoo Ink Using Nano Silver Compounds And Untact 3d Printing Technology, Jisu Lee

Open Access Theses & Dissertations

Due to a recent epidemic of COVID 19, the possibility of 3D tattoo printing technology using the Internet of Things (IoT) control system developed in a non-face-to-face contact process was identified. A non-surgical tattoo process and hygiene safety differentiated with silver tattoo ink was used to solve the health problems arising from the surgical tattoo process and to identify 3D tattoo printing techniques through a non-personal contact concept. During the tattoo processing, the image selected by the customer is sent to a designated printer via an IoT control system in a separate location. A piston-type extruder (PTE) printing technique was …

Testing The Reliability And Flexibility Of Digitizers Adapting The Rf/If Signals Over Ip Applications Using A Testbed Platform, Jose Carlos Sandoval

Open Access Theses & Dissertations

As physical constraints can be challenging for Radio Frequency (RF) telemetry, a new solution has been exploited to support the demand for RF transmissions. As frequency spectrum gets crowded with more technologies, a solution to a reliable transmission is needed. Digitizers can mitigate many of the physical constraints in order to achieve a successful RF transmission. The method includes the conversion of the RF signals to be sent over IP networks, transmit and de-convert the signal. IP networks will mitigate many disadvantages over a regular signal transmission. The authority in charge to allocate frequency bands is the Federal Communications Commission …

Brian Valdez - Dynamics And Control Of A 3-Dof Manipulator With Deep Learning Feedback, Brian Orlando Valdez

Open Access Theses & Dissertations

With the ever-increasing demands in the space domain and accessibility to low-cost small satellite platforms for educational and scientific projects, efforts are being made in various technology capacities including robotics and artificial intelligence in microgravity. The MIRO Center for Space Exploration and Technology Research (cSETR) prepares the development of their second nanosatellite to launch to space and it is with that opportunity that a 3-DOF robotic arm is in development to be one of the payloads in the nanosatellite. Analyses, hardware implementation, and testing demonstrate a potential positive outcome from including the payload in the nanosatellite and a deep learning …

Why Deep Learning Is More Efficient Than Support Vector Machines, And How It Is Related To Sparsity Techniques In Signal Processing, Laxman Bokati, Olga Kosheleva, Vladik Kreinovich

Departmental Technical Reports (CS)

Several decades ago, traditional neural networks were the most efficient machine learning technique. Then it turned out that, in general, a different technique called support vector machines is more efficient. Reasonably recently, a new technique called deep learning has been shown to be the most efficient one. These are empirical observations, but how we explain them -- thus making the corresponding conclusions more reliable? In this paper, we provide a possible theoretical explanation for the above-described empirical comparisons. This explanation enables us to explain yet another empirical fact -- that sparsity techniques turned out to be very efficient in signal …

Computing Without Computing: Dna Version, Vladik Kreinovich, Julio C. Urenda

Departmental Technical Reports (CS)

The traditional DNA computing schemes are based on using or simulating DNA-related activity. This is similar to how quantum computers use quantum activities to perform computations. Interestingly, in quantum computing, there is another phenomenon known as computing without computing, when, somewhat surprisingly, the result of the computation appears without invoking the actual quantum processes. In this chapter, we show that similar phenomenon is possible for DNA computing: in addition to the more traditional way of using or simulating DNA activity, we can also use DNA inactivity to solve complex problems. We also show that while DNA computing without …

Deep Learning (Partly) Demystified, Vladik Kreinovich, Olga Kosheleva

Departmental Technical Reports (CS)

Successes of deep learning are partly due to appropriate selection of activation function, pooling functions, etc. Most of these choices have been made based on empirical comparison and heuristic ideas. In this paper, we show that many of these choices -- and the surprising success of deep learning in the first place -- can be explained by reasonably simple and natural mathematics.

Towards A Theoretical Explanation Of How Pavement Condition Index Deteriorates Over Time, Edgar Daniel Rodriguez Velasquez, Carlos M. Chang Albitres, Vladik Kreinovich

Departmental Technical Reports (CS)

To predict how the Pavement Condition Index will change over time, practitioners use a complex empirical formula derived in the 1980s. In this paper, we provide a possible theoretical explanation for this formula, an explanation based on general ideas of invariance. In general, the existence of a theoretical explanation makes a formula more reliable; thus, we hope that our explanation will make predictions of road quality more reliable.

Nonlinear Mechanical Properties Of Road Pavements: Geometric Symmetries Explain The Empirical Difference Between Roads Built On Clay Vs. Granular Soils, Afshin Gholamy, Vladik Kreinovich

Departmental Technical Reports (CS)

It is empirically known that roads built on clay soils have different nonlinear mechanical properties than roads built on granular soils (such as gravel or sand). In this paper, we show that this difficult-to-explain empirical fact can be naturally explained if we analyze the corresponding geometric symmetries.

Segmentation And Registration Based Automatic Cancer Proton Treatment Analysis, Yang Zhang

Open Access Theses & Dissertations

Due to its low side effects, proton therapy is rapidly developing around the world. However, the time and labor it takes to deliver the treatment have prevented widespread use in the clinic setting. For this reason, an automatic proton treatment analysis system is needed to improve efficiency during the treatment process.

The challenge lies in improving the accuracy and speed of the current proton treatment analysis system. The Range shifter correction factor is considered the same value under any given condition in our treatment system. This approximate algorithm limits the accuracy of the proton treatment analysis system. In addition, medical …

Compressive And Rheological Deformation Analysis Of Large Area Pellet-Fed Material Extrusion 3d Printed Parts In Relation To In Situ Thermal Imaging, Eduardo Meraz Trejo

Open Access Theses & Dissertations

In large area pellet extrusion additive manufacturing, the temperature of the substrate just prior to the deposition of a new subsequent layer has an effect on the overall structure of the part. Warping and cracking occur if the substrate temperature is below a specific threshold, but also deformation and deposition adhesion failure occur if the substrate temperature is above a certain threshold just prior to deposition of a new layer. Currently, Big Area Additive Manufacturing (BAAM) machine users mitigate this problem by trial and error, which is costly and may result in decreased mechanical properties, monetary losses and time inefficiencies. …

Assessment Of Point Of Use (Pou) Systems For Reducing Health Risks Associated With Drinking Water Along The U.S.-Mexico Colonias In The Paso Del Norte Region, Varinia Viridiana Felix Parra

Open Access Theses & Dissertations

In the Paso del Norte Region along the U.S. Mexico Border, there are more than 5,000 families living in impoverished communities known as colonias that lack access to basic infrastructure services such as a public water system. These depend on hauling trucks that deliver water into their storage tanks. Water storage practices by colonia residents on both sides of the border pose an enormous risk for waterborne disease outbreaks and heavy metal contamination because the water quality can decrease rapidly due to volatilization of the residual chlorine, intrusion of rainfall and air-laden dust. Since connection to centralized water treatment and …

Cradle To Grave Lifecycle Process Analysis For Transuranic Waste Management Los Alamos National Laboratory, Cesar Enrique Dominguez

Open Access Theses & Dissertations

Amid World War II, in the late 1930s, nuclear fission was discovered. This revolution gave way to the development of nuclear technologies, including the world's first atomic bomb; these advancements in nuclear research left behind radioactive waste. Radioactive waste is known as the byproduct of nuclear reactors, fuel processing plants, hospitals, nuclear research facilities, as well as the result from the decommissioning and dismantling of radiation-exposed buildings and materials. This byproduct may be dangerous to workers, the public, and the environment and must, therefore, be handled with utmost safety. Given this, radioactive waste must be processed, stored, and disposed of …

Development And Environmental Testing Of A Single-Axis Printer Inside A 1u Cubesat For On-Orbit Servicing Repairs In Low Earth Orbit, Perla Rocio Perez

Open Access Theses & Dissertations

As additive manufacturing is becoming an established technology in space, new emerging strategies improve the efficiency of the printing processes. Orbital Factory 2 (OF-2) is a small satellite-or CubeSat-developed at the University of Texas at El Paso (UTEP) which launched to space on November 2019. In January 2020, it will be released in low earth orbit (LEO). OF-2 is a 1U (10x10x10cm) CubeSat that carries a one-axis printer experiment as its primary payload. This printer was developed and tested in-house. The experiment focuses on printing electrically conductive ink on a printing circuit board that verifies the conductivity on the trace …

Thermal/Mechanical Analysis And Development Of A 2000 Lbf Liquid Oxygen/Liquid Methane Rocket Engine, Marissa Garcia

Open Access Theses & Dissertations

The Center for Space Exploration and Technology Research (cSETR) is developing three rocket engines: a 5 lbf reaction control engine, a 500 lbf engine, and a 2000 lbf engine. All these engines utilize a liquid oxygen and liquid methane propellant combination. The reason methane was selected for the fuel is because methane is easy to store, is self-pressurizing, and readily available. There is also the possibility of creating methane on planets such as Mars through an electrolysis process on the ice water found on Mars.

The 2000 lbf engine, or the CROME-X, is a modular, steady-state pintle injector engine. It …

Microstructure Evolution Of Chalcogenide Materials Via Molecular Dynamics, Sharmin Abdullah

Open Access Theses & Dissertations

The properties of a material are defined by its granular microstructure which is determined by its grain evolution and the types of grain boundaries present in the structure. For example, the performance of Cadmium Sulfide/Cadmium Telluride (CdS/CdTe) solar cells can be affected by the presence of grain boundaries which makes the study of grain structure evolution a very important part of solar cell performance optimization. Grain boundary mobilities are important properties in material science and engineering as they determine grain structures under given processing and operating conditions.

In this thesis, several computational tools were used to analyze the formation and …

Towards Multiple Model Approach To Bridge Deterioration, Jin A. Collins

Open Access Theses & Dissertations

The Intermodal Surface Transportation Efficiency Act of 1991 (ISTEA) marked the start of a new era in transportation in the United States. ISTEA required transportation agencies to take a proactive approach to planning and management of their assets. This included requirements for managing pavement, bridges, safety, congestion, public transportation, and intermodal systems. For horizontal transportation assets (i.e., bridges and pavement), deterioration modeling is an essential tool (Yanev and Chen 1993). Since ISTEA, Bridge Management Systems (BMS) have been utilized to inform decision-making regarding bridge projects such as maintenance, rehabilitation, and replacement (MR&R) under financial limitations (Agrawal, Kawaguchi, and Chen 2010). …

Energy Efficiency And Fatigue Failure On Gears And Bearings For Processing Rebar Steel, Jesus Gabriel Garcia

Open Access Theses & Dissertations

Steel industry is a major emitter of air pollutants, a leading industrial consumer of water, a minor source of contaminated liquids, a massive producer of solid waste, and a significant source of CO2. The objective on this thesis work is to minimize the greenhouse gas emissions when processing steel. Gears and bearings were evaluated based on their performance when exposed to cyclic stresses. The importance for having a proper set up on rolling mills to increase efficiency for processing rebar steel has been detailed on paper. In contrast, mechanical vibration has been measured on gears and bearings to determine efficiency …

Development And Characterization Of Polyethylene Terephthalate (Pet)-Cotton Natural Fiber-Reinforced Composites From Waste Materials, Israel Alejandro Carrete

Open Access Theses & Dissertations

Unprecedented levels of production and consumption have caused a rapid exhaustion of the Earth's virgin resources, which is coupled with a fast accumulation of contaminants in the form of solid waste, especially in landfills. Two significant landfill constituents come from textile waste and discarded plastic bottles. Since there is a finite amount of space that can be feasibly used for landfills, solutions that make use of these post-consumer products are imperative. This study presents one possible solution by using surface modifications of cotton fibers to produce a natural fiber-reinforced polymer composite (NFRPC) from post-consumer textile waste and polyethylene terephthalate (PET) …

Interference Mitigation Of Adjacent Radio Frequency Signals On A Flexible Software-Defined Radio Testbed Platform, Mirza Mohammad Maqbule Maqbule Elahi

Open Access Theses & Dissertations

The radio frequency (RF) spectrum is crowded with users and adjacent frequency users are facing an increase in interference from each other. The spectrum governing body Federal Communications Commission (FCC) has the difficult task of allocating spectral bands for new users for mobile devices using 4G LTE technology. Telemetry is affected by the adjacent band 4G LTE users in terms of signal degradation. To minimize the interference between adjacent frequency users, several methods can be used. A common but inefficient method separates adjacent band frequencies using guard bands which leaves a big portion of the spectrum unused. Alternatively, adjacent RF …

Impact Of Temperature And Screw Speed On Material Meso-Structure And Tensile Strength In Large Area Pellet-Fed Additive Manufacturing, Xavier Jimenez Guzman

Open Access Theses & Dissertations

Evolution in additive manufacturing, specifically in material extrusion, has resulted in large-scale machines capable of extruding thermoplastic-matrix composite materials in higher volumes to fabricate products for large-scale applications. As with small- and medium-scale material extrusion, the properties of the final product often correlate directly with the bevy of print parameters employed. The current research was performed to evaluate the effects of the screw speed and temperature on an ABS 20%wt. carbon fiber thermoplastic processed on a Big Area Additive Manufacturing (BAAM, Cincinnati Inc) machine. Five screw speeds (50, 150, 250, 350 and 400 rpm) and three extruder temperature profiles were …

Small Satellite Development At Utep, Emily Herzog

Open Access Theses & Dissertations

The small satellite industry has seen tremendous growth in recent years. A CubeSat is a particular type of standardized small satellite that follows the CubeSat specifications. These specifications define the structural, testing, and operational requirements of the satellite. This standard facilitates cheaper design, integration, and launch of satellites, allowing smaller organizations to participate in the normally costly area of space exploration.

The University of Texas at El Paso has recognized the opportunity and has begun developing several CubeSats. The two that are the topic of this Thesis are called Orbital Factory II (OFII) and Orbital Factory X (OFX). An on-orbit …

An Alternative Method Of Calibration And Prediction For The Theta-Projection Model, Jimmy Jesus Perez

Open Access Theses & Dissertations

The combustion induced high temperature-stress conditions of industrial gas turbines used in power generation causes turbine blades to wear and break after prolonged use. The need to predict turbine blade service life is ever increasing, leading to the development of several constitutive prediction models. It is necessary to design components for high-temperature/high-stress service such that creep failure does not occur during service life. For this reason, it is important to accurately predict creep life and understand the behavior of creep deformation leading to rupture. Several models have been expanded upon to improve their effectiveness for use with particular parametric data. …

Synthesis, Characterization And Antibacterial Properties Of Silver(I) N-(4-Pyridyl) Benzamide Complexes With Varying Conterions, Mauro J. Ruiz

Open Access Theses & Dissertations

Organic semiconductor materials composed of - stacking aromatic compounds have been under intense investigation for their potential uses in flexible electronics and other advanced technologies. Herein we report a new family of seven - stacking compounds of Silver(I) N-(4-pyridyl) Benzamide with varying counterions, namely [Ag(NPBA)2]X, where NPBA is N-(4-pyridyl) Benzamine, X = NO3- (1), ClO4- (2), CF3SO3- (3), PF6- (4), BF4- (5), CH3PhSO3- (6), and PhSO3- (7), which form extended - stacking networks in one-dimensional (1D), 2D and 3D directions in the crystalline solid-state via the phenyl moiety, with average inter-ring distances of 3.823 Å. Interestingly, the counterions that contain …

Adaptive Microphone Array Systems With Neural Network Applications, Jazmine Marisol Covarrubias

Open Access Theses & Dissertations

A microphone array integrated with a neural network framework is proposed to enhance and optimize speech signals derived from environments prone to noise and room reflections that cause reverberation. Microphone arrays provide a way to capture spatial acoustic information for extracting voice input from ambient noise. In this study, we utilize and analyze established signal processing methods combined with different neural network architectures to achieve denoised and dereverberated speech signal results that are comparable with their clean, anechoic versions. The first stage of the proposed system involves using datasets containing anechoic speech recordings of speech utterances and convolving them with …

Energy Management And Control Of Smart Power Distribution Systems, Eric Galvan

Open Access Theses & Dissertations

With the development of distributed energy resources (DERs) and advancements in technology, microgrids (MGs) appear primed to become an even more integral part of the future distribution grid. In this transition to the smart power grid of the future, MGs must be properly managed and controlled to allow efficient integration of DERs. Over the past years, there has been rapid adoption of roof-top solar photovoltaic (PV) and battery electric vehicles (BEVs). Although roof-top solar PV and BEVs can provide environmental benefits (e.g., reduction of emissions), they also create various challenges for power system operators. For example, roof-top solar PV generation …

Decision Support Tools For Parking Management On University Campuses, Okan Gurbuz

Open Access Theses & Dissertations

University campuses generate and attract trips with unique characteristics. Most universities are constantly challenged by the parking congestion issues. To manage campus parking infrastructure, most universities have established parking departments. This department is referred as the University Parking Office (UPO) in this Dissertation. There is no methodology or tool to assist the UPOs in their decision-making process. This Dissertation focuses on student parking and has developed models and methodologies as decision support tools to assist UPOs in managing student parking on campuses.

This Dissertation answers six Research Questions related to parking management on university campuses: (1) How many students are …

System Dynamic Model Of 1-Dimensional Unsaturated Water And Solute Transport For Predicting Salinity Stress In Crops, Thomas Poulose

Open Access Theses & Dissertations

There is a complex non-linear system dynamic between the water and salt transport in the unsaturated vadose zone where the salt transport and accumulation affect the water fluxes and vice versa. In addition, factors such as precipitation, transpiration, water infiltration and solute transport in the unsaturated zone of subsurface soil further complicate the processes involved. We have developed a system dynamics model for simulating the one-dimensional unsaturated water and solute transport along with root water uptake in the vadose zone. The model uses finite difference method for solving Richard's equation with a sink term for water transport and root water …