Engineering Commons^™

Assessment Of An Industrial Type Radiant Heating System For Drying Rough Rice, Anne Adhiambo Okeyo

Graduate Theses and Dissertations

Rough rice is normally harvested at moisture contents (MCs) higher than that for safe storage. The objective for this study was to investigate the effectiveness of scaled-up infrared (IR) heating followed by tempering steps to dry freshly-harvested rough rice. An industrial type, pilot scale, IR drying equipment, designed to convey rough rice on a vibrating conveyor belt was used in this study. The heating zone of the equipment had catalytic IR emitters powered by natural gas. Freshly-harvested rough rice of long-grain pureline (cv. Cheniere), long-grain hybrid (cv. 6XP 756) and medium-grain (cv. CL 271) cultivars at initial moisture contents (IMCs) …

Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Andrew J. Casey

Chemical Engineering Undergraduate Honors Theses

For the 2016 WERC/IEE competition, our project regarded the efficiency and particulate matter emissions testing of wood burning heating units. The purpose of the project was to develop a cheap and effective testing method for combustion units in order to decrease manufacturers’ research and development costs. This would ultimately lower the entry barrier to the market and increase the number of manufacturers on the market. This would lead to more efficient stoves being designed and the stoves would be cheaper as a result of the increased competitive market. This would have many benefits on society; the primary benefit being that …

Haul Truck Tires Recycling, Jessica N. Lizarazu

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers. These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months. Statistics regarding discarded OTR tires are not provided by the …

Haul Truck Tires Recycling, Marina E. Lee

Chemical Engineering Undergraduate Honors Theses

The Ball Hogs competed in Task 2 - Haul Truck Tires in the 2016 Waste-Management Education and Research Consortium (WERC) International Environmental Design Contest. This task required designing a solution to recycle discarded haul truck tires from mining sites. Our solution was to use the treads of these haul truck tires to construct liners for ball mills. Recycling haul truck tires in this manner would save the mining companies a substantial amount of money and would result in a decrease of carbon emissions.

Assessing Toxicity Of Endocrine Disrupting Compounds In Wastewater For Water Reuse, Ryan Duchanois

Civil Engineering Undergraduate Honors Theses

Reclaiming treated wastewater for potable water use may be necessary to supplement drinking water sources in water scarce regions. However, Snyder et al. (2003) indicates that endocrine disrupting compounds (EDCs) are commonly found in wastewater effluents and natural waters around the world. These compounds with endocrine disrupting potential are typically found in personal care products, pharmaceuticals, and pesticides. Furthermore, according to Lemanik et al. (2007), typical wastewater treatment plants are not designed to remove EDCs.

For the purpose of water reuse, benchmarking wastewater treatment for endocrine disrupting compounds (EDCs) is necessary. The cytotoxicities of five EDCs (namely, amoxicillin, acetaminophen, triclosan, …

Towards A Fast Reconstruction Paradigm For Urban Environments In Developing Regions Affected By Natural Disasters, Christopher Maestri

Civil Engineering Undergraduate Honors Theses

Natural disasters in developing regions often displace people from their homes, into temporary shelters. These temporary shelters often consist of single-story pre-assembled tents designed to provide short-term aid for individual families. Unfortunately, single-story temporary shelters are not sufficient for accommodating large displaced populations in urban settings due to issues of land overcrowding and disruption to utilities providing water sanitation and hygiene (WASH) services (along with many other issues).

This study investigates the feasibility of implementing a multi-story steel structure, constructed with multi-use structural members and special end connectors, into future relief efforts. A multi-use structural member is an element whose …

Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Lindsey Mayo

Chemical Engineering Undergraduate Honors Theses

The performance and use of wood-burning stoves as a heating source is carefully regulated by the Environmental Protection Agency (EPA). The EPA requires a rigorous and exhaustive testing protocol be conducted on each unit before it can be sold commercially in order to ensure that the stove in question will not have a detrimental effect on the surrounding environment. However, this testing routine is incredibly time intensive and costly, resulting in a 90% decrease in the number of stove manufacturers since 1988. This decreased competition has ultimately fostered an industry free from competition and motivation to produce clean and efficient …

Removal Of Endocrine Disrupting Compounds From Secondary Municipal Wastewater, Dustin R. Resz

Chemical Engineering Undergraduate Honors Theses

Approximately 1.2 billion people around the world live in areas of physical water scarcity. This could increase to half of the world’s population by 2030 and could displace 24 to 700 million people unless steps are taken to ensure adequate water supply.1 Water scarcity is an escalating issue within the United States, specifically in Western inland states with arid climates. This scarcity is encouraging communities to investigate tertiary level municipal wastewater treatment, allowing for reuse of wastewater. Unfortunately, wastewater contains numerous contaminants that are not regulated by the Environmental Protection Agency (EPA) under the Safe Drinking Water Act (SDWA). Many …

Financial Performance In Upstream, Downstream, And Integrated Oil Companies In Response To Oil Price Volatility, Jonathan P. Garcia

Finance Undergraduate Honors Theses

This paper investigates the relation between crude oil price volatility and stock returns among oil companies using a three-part methodology, by using the West Texas Intermediate (WTI) as oil price benchmark. I asses the various indicators that set signals for oil price volatility and the interpretation of each (PMI, S&P500, DJIA, and World Crude Oil Output). This research also focuses on the relation between different types of companies in the oil industry (integrated, upstream, and downstream) and how each type of company will be assessed in a particular way to predict abnormal returns, based on market data and statistical analyses …

Baseball Portfolio Optimization, Keegan Henderson

Industrial Engineering Undergraduate Honors Theses

Portfolio optimization techniques are methods used to determine the best set of stocks in which to invest. Mean-variance optimization, one method of portfolio optimization, attempts to find the set of portfolios that have the maximum expected return at each level of risk (Jorion, 1992). Another technique, Monte Carlo simulation, uses random number generation to create a probability distribution of potential returns (Kwak & Ingall, 2007). This can be used to determine the risk of potential investments not returning a certain desired amount (Thompson & McLeod, 2009). Though traditionally used in the world of finance, these tools can also be utilized …

Modeling Supply Chain Resiliency, Jeff A. Hazel

Industrial Engineering Undergraduate Honors Theses

Engineered Resilient Systems (ERS) is a Department of Defense (DoD) program focusing on the effective and efficient design and development of complex engineered systems throughout their life cycle. There is a growing literature with qualitative definitions of resilience and quantitative models for systems with one performance measure. This paper uses a quantitative resilience framework (the Framework for ERS) that includes system design options, reliability, threats, vulnerabilities, responses, and consequences assessed in multiple system performance measures. The framework assists in establishing a model for any system to evaluate resiliency. This paper applies this framework using Multiple Objective Decision Analysis (MODA) to …

Analysis Of Bolted Beam-Column Connections With Multiple Bolts Per Row And Column Web Stiffeners, Benjamin C. Sutherland

Civil Engineering Undergraduate Honors Theses

Bolted beam-column connections are a common moment connection used in the design of steel buildings. Existing design guides include design parameters for bolt configurations having one bolt on either side of the beam web for each row of bolts. There is potential for increasing connection strength by adding additional bolts on the outside of these rows. This addition could be useful in retrofit scenarios, or even in the design of new structures. In this research, finite element analysis is used to analyze various beam-column connections and t-stub connections. The modeling methods, research process, and conclusions are explained in the thesis …

Measuring Relative Humidity In Concrete Pavements As A Method To Assess Asr Mitigation Measures, Remington G. Reed

Civil Engineering Undergraduate Honors Theses

Alkali-silica reaction (ASR) in concrete is partly facilitated by available moisture within the concrete. In order to better understand this facilitation and to develop processes for ASR mitigation methods, it is necessary to establish a means of monitoring internal relative humidity (RH) within the concrete. Current procedures for measuring RH are time consuming; requiring several hours of equilibration time and specific external conditions to yield accurate results. In order to better understand RH monitoring, laboratory tests were conducted using commercially available RH probes and different controlled environments. Probes were carefully monitored and calibrated in controlled environments, and laboratory tests on …

Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Collin W. Michael

Chemical Engineering Undergraduate Honors Theses

The University of Arkansas StoveHOGS team developed a method for efficiency and particle emissions testing of wood fired heaters. The EPA currently regulates the particulate emissions of wood burning stoves, and the goal of this project was to develop a cheaper, easier method for small manufacturers to test the efficiency and particulate emissions of wood burning stoves without sending them to a testing facility. The team used EPA and CSA testing standards to design and test a method that could accomplish the same task in a simpler and more cost effective manner.

Effect Of Impact Angle On Astrocyte Gene Expression, Nicholas A. Chavis

Biomedical Engineering Undergraduate Honors Theses

Over one million people each year experience some form of traumatic brain injury. Every individual’s injury is different as impacts can affect different parts of the brain in various ways. This study was conducted to test the impact angles effect on astrocytes by measuring gene expression of TNF- alpha, an inflammation marker, and GFAP, a gene released in response to reactive astrocytes, following impacts from 0, 45, and 90 degrees. Results were recorded from Polymerase Chain Reaction via the delta delta Ct method and compared to the control group for to show under-regulation or up- regulation of the genes of …

Atomic Force Microscopy Based Dna Analysis, Drew Creighton

Mechanical Engineering Undergraduate Honors Theses

This report explores dry and wet scanning of a surface and DNA pickup using an AFM, as well as fluorescent staining of DNA. Dry and wet scans of DNA were obtained using a cantilever AFM tip in tapping mode. Dry scans were found to be clearer than wet scans; however, the drying process was found to decrease the thickness of DNA 2–4 times less than its original thickness. Alternately, wet scans were found to be less clear than dry scans and introduced more noise into the images obtained. Additionally, DNA kept its initial thickness during wet scanning. DNA was capable …

Cfd Model For Ventilation In Broiler Holding Sheds, Christian Heymsfield

Biological and Agricultural Engineering Undergraduate Honors Theses

Broiler production in Arkansas was valued at over $3.6 billion in 2013 (University of Arkansas Extension of Agriculture). Consequently, improvement in any phase of the production process can have significant economic impact and animal welfare implications. From the time poultry leave the farm and until they are slaughtered, they can be exposed to harsh environmental conditions, both in winter and in summer. After road transportation, birds are left to wait in holding sheds once they arrive at the processing plant, for periods of approximately 30 minutes to two hours. This project was interested in this holding shed waiting time during …

Crizotinib And Ceritinib Induce Apoptosis And Necrosis In Primary Rat Hepatocytes With Distinct Capacity, Alec T. Salminen

Biomedical Engineering Undergraduate Honors Theses

Drug development makes up a major portion of biomedical engineering research interests. The FDA oversees the introduction, experimentation, and implementation of all drugs before market approval is granted. Even after market approval is granted, the FDA continues to monitor the safety of all drugs. Crizotinib and ceritinib are two anaplastic lymphoma kinase (ALK) inhibitors recently approved by the FDA. Both drugs are indicated for treatment of non-small cell lung cancers (NSCLC) with abnormal ALK gene, and they are approved with a companion diagnostic test that determines ALK abnormality. Clinical trial data suggest that crizotinib and ceritinib can cause liver injury, …

Investigating The Mechanical Behaviors Of Organic/Inorganic Composite Bone Scaffolds, Parker Davidson

Biomedical Engineering Undergraduate Honors Theses

The regeneration of bone over a large area cannot occur without a structure for the bone cells to bind and divide. The use of an organic/inorganic composite bone scaffold appears to be a promising alternative to the current clinical standard of bone grafting. Bone grafting is very limited, in that the size and shape of the area are hard to replicate and the use of donor tissue can trigger an immunologic response resulting in rejection of the bone tissue. This study experimented with composite bone scaffolds which can be made to fit the shape of the area in which bone …

Exploring Biomarkers For Point Of Care Bladder Cancer Detection, Cassandra M. Walker

Biomedical Engineering Undergraduate Honors Theses

Bladder cancer is the 5th most common non-cutaneous human cancer in the United States. While effective methods of detecting bladder cancer are currently practiced, they are often expensive and invasive. There is a need for a noninvasive detection method that can be used in areas with few medical resources. Cell free DNA in urine is normally present only in very low concentrations. Abnormally high levels of cell free DNA in urine could be indicative of disease. This study tests the hypothesis that DNA present in urine can be used as a biomarker for bladder cancer before hematuria is seen in …

Optimized Protocol For Measuring 2-Nbdg Uptake As A Cellular Marker Of Glycolytic Demand, Drew Folgmann

Biomedical Engineering Undergraduate Honors Theses

2[N-(7-nitrobenz-2-oxa-1,2-diaxol-4-yl)amino]-2-deoxyglucose (2-NBDG) a fluorescently tagged analog of FDG is ideal for in vitro studies and imaging. 2-NBDG has been proven to be an adequate marker for glucose uptake in many different types of cells [1]. However, across the spectrum of 2-NBDG use a lack of consensus is observed for the following questions. What is the ideal time to fast cells to optimize cellular uptake of 2-NBDG? Also, what is the ideal concentration of 2-NBDG to be used when quantifying glucose uptake? Finally, what is the effect of serum on the uptake of 2-NBDG? To answer these questions and understand glucose …

Micellular Electrokinetic Chromatography For Studying Amyloid Beta Oligomer Membrane Affinity, Andrew Bryson

Biomedical Engineering Undergraduate Honors Theses

Amyloid Beta (Aβ) was the major focus of this study. It is a peptide that is present in the brain with a high tendency to self-aggregate. When this protein aggregates, it forms oligomers and protofibrils which in turn are deposited as senile plaques in the brain. The reason for the concern with these plaques is their association with the neurological disorder Alzheimer’s disease. It has been found that the most dangerous oligomers are formed in a portion of the plasma membrane known as lipid rafts. The purpose of this study was to understand how micelles affect the aggregation properties of …

Non-Directional Conjugation Of Fluorescent Antibodies To Gold Nanoparticles For Stem Cell Therapy, Kunal B. Shah

Biomedical Engineering Undergraduate Honors Theses

The objective of this study was to design citrate-coated gold nanoparticles conjugated with FITC-IgG, a fluorescent antibody, and to qualitatively and quantitatively measure the resulting fluorescent emission. Optical properties of the gold nanoparticles were measured at various stages to provide evidence of successful conjugation. The absorbance spectrum of the citrate gold nanoparticles was compared to that of the reaction mixture containing the gold nanoparticles and the FITC-IgG. A noticeable broadening of the absorption peak was observed at 519 nm indicating a surface modification of the gold nanoparticles. Fluorescence data was obtained with a fluorospectrometer and revealed a significant amount of …

Design Of A 3d-Printed Device For Diffuse Reflectance Spectroscopy Calibration As A Step Towards Clinical Translation, Nontapoth Vongkittiargorn

Biomedical Engineering Undergraduate Honors Theses

The diffusive reflectance and spectroscopic microendoscopy (DRSME) is a multimodal imaging system that harnesses its usefulness from different light sources. One of the modalities, diffuse reflectance spectroscopy (DRS), has been used in our lab to investigate optical properties of epithelial tissues using a broadband white light as the main source. Calibration of DRS is required as it can obtain the maximum intensity and convert it to absolute reflectance. Current manual-adjusted calibration can be lengthy and often lead to inconsistent results. Therefore, a new method of calibration is introduced where additive manufacturing (or 3D printing) technology is fully utilized.

The instrumentation …

Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Elisabeth E. Westcott

Chemical Engineering Undergraduate Honors Theses

The Environmental Protection Agency (EPA) is continually revising the regulations on wood-burning units to reduce the particulate matter emissions in the United States. These revisions have caused a large decline in wood-burning stove manufacturers as they bring the need for research and development on current units and small manufacturers cannot burden the large costs. The StoveHogs became aware of this manufacturer decline in the industry and saw an opportunity to help small manufacturers, backyard inventors, and the stove industry as a whole. In order to reduce the costs of research and development on stoves, the StoveHogs designed and tested a …

Wastewater Reuse, Zachary J. Bare

Chemical Engineering Undergraduate Honors Theses

Approximately 1.2 billion people around the world live in areas of physical water scarcity. This could increase to half of the world’s population by 2030 and could displace 24 to 700 million people unless steps are taken to ensure adequate water supply. Water scarcity is an escalating issue within the United States, specifically in Western inland states with arid climates. This scarcity is encouraging communities to investigate tertiary level municipal wastewater treatment, allowing for reuse of wastewater. Unfortunately, wastewater contains numerous contaminants that are not regulated by the Environmental Protection Agency (EPA) under the Safe Drinking Water Act (SDWA). Many …

Rapid, Low-Cost Biosensor For Water-Borne Pathogens In Low-Resource Environments, Kimberly Cribbs

Chemical Engineering Undergraduate Honors Theses

When testing water quality, “microbiological results typically require a minimum of 24 hours to complete” due to reliance on the traditional and inexpensive cultivation method. In 2000, an isothermal DNA amplification method termed loop-mediated isothermal amplification (LAMP) was invented allowing for microbiological assessments to be performed in less than one hour without the need for an expensive thermocycler. In 2013, the World Health Organization reported LAMP as an “attractive diagnostic platform for resource-poor settings: it is fast [15-40 min], isothermal [requiring only a heat block], robust to inhibitors and reaction conditions that usually adversely affect PCR methods, and it generates …

Investigating The Modulation Of Aggregating Amyloid Beta 40, Marlee J. Motes

Chemical Engineering Undergraduate Honors Theses

Amyloid beta protein has been linked to the formation of Alzheimer’s disease in patients.¹ Plaques form from amyloid beta fibrils. The formation of these plaques between neural connections in the brain are associated with Alzheimer’s disease.² The reduction of the formation of fibrils can be linked to utilizing protein mimics. The protocols that are used to reproduce the simulation of amyloid beta in the brain can be very important. Also, the structure of the protein mimic that is being used to inhibit the formation of fibrils can determine how the amyloid beta plaques are reduced.

The structure of sequence KLLFFLFFLLK …

Werc Task #1 - Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Jonathan A. Shumaker

Chemical Engineering Undergraduate Honors Theses

A design of a method for calculating the efficiency and particulate matter emission rates was developed for use on wood stoves. The project was completed for the WERC competition which is an international design contest. The prevalence of wood burning as a form of heating, current EPA regulations, and current market conditions were major factors in forming the necessity of this testing method. Design was not limited to outlining the design specifications, the apparatus was built and run. Optimization of the method continued until completion of the project. If the method would continue to be improved then it would be …

Werc Task #1 - Open: Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Teni R. Butler

Chemical Engineering Undergraduate Honors Theses

Wood burning has significant environmental and health impacts. This research focused on creating low-cost, reliable test methods for identifying particulate matter emissions to the atmosphere, while obtaining essential data for efficiency calculations of wood combustion.