Engineering Commons^™

Properties Of Ambiguity Functions, John Mulcahy-Stanislawczyk

Open Access Theses

The use of ambiguity functions in radar signal design and analysis is very common. Understanding the various properties and meanings of ambiguity functions allow a signal designer to understand the time delay and doppler shift properties of a given signal. Through the years, several different versions of the ambiguity function have been used.

Each of these functions essentially have the same physical meaning; however, the use of different functions makes it difficult to be sure that certain properties hold for different formulations. This work proves several parallel properties of two versions of the asymmetric ambiguity function, the symmetric ambiguity function, …

Comparison Of A Sierpinski Gasket Monopole Antenna To Bow-Tie Antennas Based Off The Fractal Iterative Shapes, Kyle Nathan Murg

Open Access Theses

Antennas are an integral part of mobile devices. Recently, the demand for smaller phones has increased requiring smaller components within the device. This leads to problems with performance and limitations of RF systems within mobile devices including antennas which have been affected by the size thus affected frequency output. In this thesis, fractal theory will be utilized to compare the performance of the Sierpinski Gasket Monopole antenna to single band antennas to see if this is a viable substitute in mobile applications. By utilizing simulations and physical antennas, the performance will be observed at each frequency band and compared.

Improving Indoor Air Quality Through Botanical Air Filtration In Energy Efficient Residences, Daniel William Newkirk

Open Access Theses

According to the U.S. EPA, the average American spends 90% of their time indoors where pollutants are two to five times more prevalent than outside. The consequences of these pollutants are estimated to cost the U.S. 125 billion dollars in lost health and productivity. Background literature suggests botanical air filtration may be able to solve this problem by leveraging the natural ability of plants to purify indoor air. By improving indoor air quality, energy consumption can also be reduced by bringing in less outside air to dilute contaminants within the space. A botanical air filter, called the Biowall, was designed …

Variability In Uv Disinfection Of Municipal Wastewater, Angela Patricia Ortiz

Open Access Theses

Variability in the performance of UV disinfection systems is hypothesized to be attributable to variability in the parameters that influence the overall performance. Predictability of process performance in UV disinfection systems should be possible, if variability in these input parameters can be defined. The objective of this project was to define variability in parameters that are known to affect the performance of UV disinfection systems so as to inform design and operation conditions for a large-scale UV disinfection system that was recently applied at the Belmont facility in Indianapolis, Indiana, and other systems. The present study focused on quantification of …

Software Architecture And Development For Controlling A Hubo Humanoid Robot, Manas Ajit Paldhe

Open Access Theses

Due to their human-like structure, humanoid robots are capable of doing some complex tasks. Since a humanoid robot has a large number of actuators and sensors, controlling it is a difficult task. For various tasks like balancing, driving a car, and interacting with humans, real-time response of the robot is essential. Efficiently controlling a humanoid robot requires a software that guarantees real-time interface and control mechanism so that real-time response of the robot is possible. Addition- ally, to reduce the development effort and time, the software should be open-source, multi-lingual and should have high-level constructs inbuilt in it.

Currently Robot …

Nanohub Database Analysis: Using Anomaly Detection Method And Principal Component Analysis, Mengyang Qi

Open Access Theses

This thesis analyzes usage data from nanoHUB.org, which is a web-based infrastructure for e-collaboration among nanotechnology simulation community. Previous analysis of nanoHUB database showed he nanoHUB usage data follows an unknown, heavy-tailed distributions. This thesis extends the analysis and develops an automatic anomaly detection method based on piece-wise linear approximation. The anomaly here refers to collective user behaviors different from others. The result shows that the method can accurately detect the anomalies in the unknown, heavily detailed distribution. This thesis also applies anomaly detection method and principal component analysis to other databases in nanoHUB and successfully reveals differences between different …

A Comparative Analysis Of An Original And A Post-Hoc Application Of Lean Six Sigma Methodology, Jin Qiu

Open Access Theses

Current society develops faster and faster every day with customers' demands increasing rapidly. Decreasing time for product development and enhancing customer satisfaction are becoming more significant. In the business world, there is no industry that could exist without an efficient supply chain. In the fierce competitive environment of today, the supply chain must address potential problems and risks that may exist and assure continuous improvement.

One common supply chain management practice in many industries is to apply lean methodology to the supply chain model in order to maximize the customers' value and eliminate waste. By eliminating waste, the process can …

A Novel Three Degree-Of-Freedoms Oscillation System Of Insect Flapping Wings, Yi Qin

Open Access Theses

We propose an oscillation system to replicate the dynamic behavior of flapping wings, inspired by insect flight muscles. In particular, we study the flight of the fruit fly Drosophila virilis . We model the wing as a rigid body with three degree-of-freedom, described by three Euler angles: the stroke angle, the rotation angle and the deviation angle. Insect flight muscles are separated into two types: power muscles and control muscles. One actuator and one torsional spring at the stroke angle act as the power muscles. Two torsional springs at the rotation angle and the deviation angle mimic the control muscles. …

Risk-Based Bridge Inspection Practices, Rebecca Reising

Open Access Theses

Improving bridge safety, reliability, and the allocation of bridge inspection resources are the goals of the proposed risk based bridge inspection practices. Currently, most bridges in the United States are inspected at a fixed calendar interval of 24 months, without regard to the condition of the bridge. Newer bridges with little or no damage are inspected with the same frequency as older, more deteriorated bridges thus creating inefficiency in the allocation of inspection resources. Because of limited resources, it is not possible to spend the necessary time examining bridges that are in poor condition and require extra attention since equal …

Modeling Preventive Maintenance In Complex Systems, Jessica Rivas

Open Access Theses

This thesis presents an explicit consideration of the impacts of modeling decisions on the resulting maintenance planning. Incomplete data is common in maintenance planning, but is rarely considered explicitly. Robust optimization aims to minimize the impact of uncertainty--here, in contrast, I show how its impact can be explicitly quantified. Doing so allows decision makers to determine whether it is worthwhile to invest in reducing uncertainty about the system or the effect of maintenance. The thesis consists of two parts. Part I uses a case study to show how incomplete data arises and how the data can be used to derive …

A Lean Logistics Assessment Tool For Smes In The Manufacturing Sector, Diana Lorena Sanchez Ramirez

Open Access Theses

This study developed an assessment tool to rate the maturity of the current and desired states of lean logistics operations in small and medium enterprises. The tool consists of 48 best practices classified into 8 critical factors: Inventory, Transportation, Administration, Information Systems, Warehouse, Forecasting, Packaging and Supplier Network. Each of the best practices and critical factors were identified throughout a thorough literature review and comparative analysis between authors to define commonalities among them. Using gap analysis; this tool results in a SWOT matrix providing a roadmap for lean implementation. The resulting model was evaluated by subject matter experts in different …

Investigating The Role Of Dem Resolution And Accuracy On Flood Inundation Mapping, Siddharth Saksena

Open Access Theses

Saksena, Siddharth. M.S.C.E., Purdue University, May 2014. Investigating the Role of DEM Resolution and Accuracy on Flood Inundation Mapping. Major Professor: Venkatesh Merwade. Topography plays an important role in determining the accuracy of flood inundation maps. A lot of the current flood inundation maps are created using topographic information derived from Light Detection and Ranging (LiDAR) data. Although LiDAR data is very accurate, it is expensive, computationally time consuming and not available in several areas across the United States and around the world. As a result, coarser resolution DEMs which are easily available but less accurate are used for flood …

Floodplain Mapping Using Soil Survey Geographic (Ssurgo) Database, Nikhil Sangwan

Open Access Theses

Floods are the most damaging of all natural disasters, adversely affecting millions of lives and causing financial losses worth billions of dollars every year across the globe. Flood inundation maps play a key role in assessment and mitigation of the potential flood hazards. However, there are several communities in the United States for which the flood risk maps have not been published yet, as the current flood inundation mapping methods are typically very expensive and time consuming. The objective of this study is to develop and examine an economical alternative approach to floodplain mapping using widely available soil survey data. …

Analysis Of Eye Tracking Data Obtained By Customers’ Product Evaluations, Shweta Sanjay Sareen

Open Access Theses

Within the mechanical engineering discipline, product representational studies have been used to inform engineers on the suitability of their product designs for prospective customers. Mainly based in customers' oral responses, engineers would modify the product design accordingly. The incorporation of eye tracking data, in addition to the oral responses, in these product representational studies is a recent addition. This case study performs data analysis of a product representational study conducted by Reid, MacDonald and Du (2012), which considers the impact of 2D and 3D product representation on customer judgments with associated eye gaze patterns. The aim of this thesis is …

Rheological Properties Of Laponite And Chemically Modified Laponite Suspensions, Meng Shen

Open Access Theses

This research investigates the rheological properties of concentrated laponite RD suspensions modified through the addition of laponite RDS and sodium pyrophosphate (SPP). The work is aimed at establishing the possible suitability of these materials for treating liquefaction susceptible sands. This application requires that a laponite suspension initially exhibits liquid like behavior and low viscosity that allow its delivery into the pore space of a sand, but that over time the suspension develop a gel structure with solid like behavior that can serve to restrict sand particle mobility during earthquake shaking.

The experimental program made use of a Physica MCR 301 …

Signalized Corridor Assessment, William Benjamin Smith

Open Access Theses

Traffic engineers are often required to investigate the operation of a corridor and determine if there are any areas for improvement. Typical performance measures used to aid in the analysis are volume-to-capacity ratio and average delays based on the Highway Capacity Manual method. Signal timing software might also be used to adjust the split timings in effort to improve the corridor. This thesis discusses procedure to implement split timing optimization and delay analysis to enhance the current process of corridor assessment.

This study examined the newly opened US-231 bypass corridor outside of West Lafayette, IN. Initially, all intersections were operating …

Guidelines For Construction Companies To Decide Between Outsourcing And Self-Performing For Prefabricated Components, Sebastian Soto Ortiz

Open Access Theses

Prefabrication and modularization has been used in the construction industry for decades. It has recently made a resurgence worldwide providing increased productivity, safety, quality and construction schedule. This research has focused on the situation where a construction company has decided to use prefabrication and faces two possibilities, they either will self-perform or they will outsource the construction of the prefabricated components. The decision making process used by a construction company to determine whether to outsource or self-perform prefabricated components is examined and analyzed.

Prefabrication is an industrial process in which certain components are manufactured in a specialized facility. These items …

Computer Modeling And Simulation Of Implantable Medical Device Heating Due To Mri Gradient Coil Fields, Bryan David Stem

Open Access Theses

For patients with implantable medical devices, the ability to safely undergo MRI scanning is critical to ensuring the highest standard of care. The gradient coils of an MRI generate kilohertz frequency, time varying magnetic fields. These magnetic fields induce a voltage on the external case of metallic, implantable medical devices through electromagnetic induction. Since the magnetic field generated by a gradient coil is time varying, the induced voltage results in the flow of eddy currents which can cause heating effects. These heating effects have been successfully modeled using ANSYS Maxwell and ANSYS Mechanical software packages.

The multi-physics simulation and solution …

Effects Of Crossflow In An Internal-Cooling Channel On Film Cooling Of A Flat Plate Through Compound-Angle Holes, Zachary Taylor Stratton

Open Access Theses

The film-cooling holes in turbine blades are fed from an internal cooling channel. This channel imposes a crossflow at the entrance of the holes that can significantly affect the performance of the cooling jets that emanate from those holes. In this study, CFD simulations based on steady RANS with the shear-stress transport (SST) and the realizable k -ε turbulence models were performed to study film cooling of a flat plate with cooling jets issuing from eight round holes with a compound angle of 45 degrees, where the coolant channel that fed the cooling jets was oriented perpendicular to the direction …

Biaxial Shear/Tension Failure Criteria Of Spectra Single Fibers, Jianzhuo Sun

Open Access Theses

An experimental study was conducted to develop the biaxial failure surface criteria of single Spectra 130d and 100d filaments in a torsion-tension environment. The cross-sectional profiles of single Spectra fibers were investigated using scanning electron microscopy and X-ray computed tomography. A pin-gripping method to fix the ends of a polyethylene single fiber was developed. Effects of pin diameter on failure stress for both Spectra 130d and 100d were characterized. It was found that the perturbed stress field effect can be neglected when the pin diameter is larger than 0.8 mm. Additionally, the effect of the sample's gage length on fiber …

Attached-Growth System For Nitrification At Low Temperature, Zhe Sun

Open Access Theses

Attached-growth biological treatment systems have potential to conduct nitrification in cold-temperature climates. In this research, in order to simulate the attached-growth nitrification process (using BOBBER biological reactor) at a real wastewater treatment facility, two laboratory-scale mini-BOBBER systems were installed in a temperature-controlled room and were operated for 101 days with pure ammonium chloride feed solution. Steady-state conditions were approached at 20°C, 15°C, 10°C, and 5°C. In addition, a series of batch experiments were conducted at temperatures of 20°C and 5°C to investigate the relationship between nitrification rate and ammonia-N concentration. Results from these experiments were analyzed and compared with the …

Characterization Of Thermal And Mechanical Properties Of Porous Material For Electronic Cooling Applications, Ninad Tushar Trifale

Open Access Theses

Metal foams are considered beneficial for several applications because of its significantly large surface area for a given volume. Foams form a high thermal conductive network in a thermal interface for electro cooling applications. The porous structures are relatively compliant and can provide for a better contact and thereby have a lower thermal resistance. Porous heat sinks made of aluminum foam have been well studied in the past. It is not only cost effective due to the unique production process, but also attractive for the theoretical modeling study to determine the performance. A study on the thermal and mechanical characterization …

Reliability Guided Resource Allocation For Large-Scale Supercomputing Systems, Shruti Umamaheshwaran

Open Access Theses

In high performance computing systems, parallel applications request a large number of resources for long time periods. In this scenario, if a resource fails during the application runtime, it would cause all applications using this resource to fail. The probability of application failure is tied to the inherent reliability of resources used by the application. Our investigation of high performance computing systems operating in the field has revealed a significant difference in the measured operational reliability of individual computing nodes. By adding awareness of the individual system nodes' reliability to the scheduler along with the predicted reliability needs of parallel …

A Farm Management Information System With Task-Specific, Collaborative Mobile Apps And Cloud Storage Services, Jonathan Tyler Welte

Open Access Theses

Modern production agriculture is beginning to advance beyond deterministic, scheduled operations between relatively few people to larger scale, information-driven efficiency in order to respond to the challenges of field variability and meet the needs of a growing population. Since no two farms are the same with respect to information and management structure, a specialized farm management information system (FMIS) which is tailored to the realities on the ground of individual farms is likely to be more effective than generalized FMIS available today.

This thesis presents the design of a FMIS using proven user-centered design principles. This approach resulted in the …

Retrofiting Lid Practices Into Existing Neighborhoods: Is It Worth It?, Timothy Wright

Open Access Theses

Low impact development (LID) practices are gaining popularity as a way to manage stormwater close to the source. This reduces infrastructure requirements and helps to maintain hydrologic processes close to predevelopment conditions. Studies have shown LID practices to be effective in reducing runoff and improving water quality. However, little has been done to aid decision makers in selecting the most effective practices for their needs and budgets.

To this end, the L-THIA LID model has been applied. Using readily available data sources, multiple scenarios can quickly be examined, and then analyzed to determine the cost of implementation and the approximate …

An Analysis On Causes Of Late Final Payment And Release Of Retainage: Electrical Subcontractors’ View, Xuejing Zhang

Open Access Theses

Using the survey approach, this study identified the underlying causes of late payments and release of retainage for electrical subcontractors, attempting to answer the questions, "What were the minimum, maximum and average delay days of final payment and release of retainage?", "What were the rank of factors in terms of significance on delaying final payment and release of retainage?", and "What were the rank of factors in terms of frequency on delaying final payment and release of retainage?" A survey questionnaire was developed and distributed to about 150 professionals in electrical subcontractors. 29 reports were collected. Based upon the analysis …

The Influence Of Gaps On The Frequency Response Of A Beamspring Contact System, Wenbin Zhang

Open Access Theses

Some mechanical systems with gaps such as in disc brakes and Cardan joints exhibit nonlinearity under certain load conditions, which is unpredictable and highly sensitive to initial conditions. Previous studies were mainly focused on either a single-degree-of-freedom (DOF) system or a flexible beam with uniform elastic foundation. The analysis of this thesis is a combination of these two where gaps are first introduced to a flexible beam model. A model of a beam resting on compliant foundation with gaps has been developed and analyzed. The assumed modes method is used to derive the equations of motion (EOM's) for the system. …

Mechanistic Study Of The Hydrothermal Reduction Of Palladium On The Tobacco Mosaic Virus, Oluwamayowa Oluwarotimi Adigun

Open Access Theses

Synthesis of nanorods and nanowires is becoming more and more important due to interest in them in a wide range of disciplines. The genetically engineered tobacco mosaic virus (TMV1Cys) provides a template for synthesis of uniform metal nanorods at mild operating conditions and without the use of any expensive technology compared to conventional synthetic methods. The discovery of the hydrothermal synthetic scheme has allowed the production of higher quality nanorods on the TMV template. However, the mechanism for reduction and growth in this process is still not understood. In this paper, the mechanism of synthesis for producing uniform, controllable palladium …

Developing An Unstructured Model To Investigate The Effect Of Ethanol On Product Yields For Glucose And Xylose Cofermentation In Saccharomyces Cerevisiae 424a (Lnh-St), Shane D. Clingenpeel

Open Access Theses

Production of bio-ethanol from lignocellulose requires the efficient fermentation of glucose and xylose, even in the presence of inhibitors. The desired product, ethanol itself, will inhibit the fermentation. A further understanding of how ethanol affects the organism is critical to overcoming its inhibition.

This thesis evaluated the effect of ethanol on the cofermentation of glucose and xylose in two different cases. The first case had an unstructured model created for Saccharomyces cerevisiae 424A (LNH-ST), a genetically modified strain of yeast capable of cofermenting glucose and xylose. The differential equations were based around sugar consumption, and the product yields were investigated …

Small Strain Stiffness Of A Carbonatic Fine Grained Soil, Sulaiman Dawood

Open Access Theses

The work presented in this thesis is part of a broad effort aimed at the characterization of the engineering properties, microstructure and mineralogy of soft fine-grained carbonatic soil deposit in Southwestern Indiana (Daviess Co.). The specific focus of this thesis is the characterization, through both field and laboratory measurements, of the small strain behavior of this soil, commonly referred to as a "marl."

Index tests indicate that the 3.5 m marl layer present at the site is characterized by two soil types alternating in small sublayers: a high plasticity silt (soil M) with wn ∼60% and CaCO3 ∼60%, mostly in …