Engineering Commons^™

Advancements In Signal Processing And Image Reconstruction For Active Microwave Thermographic Measurements, Logan Martin Wilcox

Doctoral Dissertations

Active microwave thermography, or AMT, is a coupled electromagnetic-thermographic nondestructive testing and evaluation technique. AMT has found success in a variety of inspection needs in the aerospace, space, and infrastructure fields due to its unique type of thermal excitation. During an AMT inspection, a specimen is exposed to microwave energy from a radiating source (i.e., an antenna). This exposure to microwave energy results in dielectric/magnetic heating, which causes an increase in temperature and potential defect indications to manifest on an inspection surface (which is measured via an infrared camera). Due to the use of an antenna, there is a spatially …

Deep Learning Architecture Design For Nano-Satellite Image Super-Resolution, William Everette Symolon

Doctoral Dissertations

Increasing threats to U.S. national security satellite constellations have resulted in an increased interest in constellation resilience and satellite redundancy. NanoSats have contributed to commercial, scientific and government applications in remote sensing, communications, navigation, and research. They also have the potential to enhance satellite constellation resilience. However, the inherent size, weight, and power limitations of NanoSats enforce constraints on imaging hardware; the small lenses and short focal lengths result in imagery with low spatial resolution, which limits the utility of CubeSat images for military planning purposes and national intelligence applications. This research proposed a deep learning architecture capable of enhancing …

Investigating The Effects Of Fly Ash On The Properties Of Silica-Deficient High Alumina Materials, Sai Akshay Ponduru

Doctoral Dissertations

This research is made up of five studies mainly focused on attaining sustainability in high alumina cements like calcium aluminate cement (CAC) and calcium sulfoaluminate belite cements (CSAB) by partially replacing them with additives and supplementary cementitious materials (SCMs) like fly ash (FA). The first study focused on understanding the reaction kinetics of CAC and FA binders at different replacement levels (i.e. between 10%-to-50% by mass) and their effect on mechanical properties. It was also shown that the reactive nature of FAs can be determined by calculating a single parameter called number of constraints (nc) derived from topological constraint theory. …

Data-Driven Mulitiscale Modeling Of Electrochemical Transport, Non-Linear Electrical Contact, And Additive Manufacturing Processes, Emmanuel Olugbade

Doctoral Dissertations

The growing demand for high-efficiency energy systems and advanced manufacturing technologies requires predictive frameworks that link atomic-scale physics with engineering-scale performance. This dissertation develops a unified multiscale modeling approach that integrates molecular dynamics, density functional theory, finite-element analysis, and machine learning to connect structure, transport, and performance across materials and processes. Depending on the interactions involved, the framework employs loose coupling for parameter transfer, tight coupling for two-way feedback, and hybrid coupling where machine-learning surrogates accelerate high-fidelity simulations while retaining physical interpretability. In electrochemical systems, an XGBoost-enhanced single-particle model reproduces P2D-level electrolyte potential dynamics at roughly one-hundredth the computational cost, …

Characterization And Deportment Of Anode Impurities In Copper Electrorefining, Charles Michael Campbell

Doctoral Dissertations

The objective of this research was to study the deportment of the group 15 elements, arsenic, antimony and bismuth during copper electrorefining. Samples were collected from six industrial copper anodes with different compositions. Specimens were physically characterized and electro refined to understand the differences in the behavior of selected impurities. Inclusions in the cast metal structures were characterized using automated scanning electron microscopy and energy dispersive spectroscopy to measure and correlate their size, shape and composition. Arsenic and lead were found to have a positive correlation between concentration and size of inclusions. Using wavelength dispersive spectroscopy, multiphase inclusions were examined, …

Optical Sensor Instrumentation For Enhanced Continuous Caster Development, Hanok Wondimagegnehu Tekle

Doctoral Dissertations

Fiber-optic sensors are an emerging technology that can enhance process monitoring and control in steelmaking. They are especially valuable in the continuous caster’s harsh environment. This dissertation presents the industrial application and demonstration of three sensor types: single-mode silica fiber with Rayleigh-based Optical Frequency Domain Reflectometry (OFDR), sapphire fiber (single-crystal alumina) with Fiber Bragg Gratings (sFBG), and an in-line Raman spectroscopy probe. Each sensor served a distinct role in the continuous caster. Rayleigh OFDR sensors were embedded in tundishes for distributed thermal mapping at 7-mm spatial resolution across ≈4 m. Measurements were taken during preheating, casting, and ladle exchanges, and …

Identification Of Corrosion Damage, Vibration, And Loose Conections In Aircraft Data Transmission Lines Using Reflected And Transmitted Signals; Formulation Of Vegetable Oil-Based Nanofluids As Cutting Fluids For Mql Machining, Saidanvardzhon Valiev

Doctoral Dissertations

This research presents a novel Frequency Domain Transmitometry (FDT) method that uses transmitted signals (S21) to detect and characterize aircraft data transmission lines (ADTL) corrosion damage without additional reflectometry circuitry. Corrosion experiments were conducted according to ASTM G85-A5 over 14 weeks. Combined FDT and reflected signals (S11) analyses revealed distinct three-peak signatures associated with damage and corrosion. The square root of the Area Under the Curve (AUC) of the FDT damage peak and the Full Width at Three-Quarter Maximum (FW3QM) of the S11 damage peak is correlated with corrosion propagation depth and width. S11 signals were further used for vibration …

Effect Of Thermomechanical Processing And Heat Treatment On The Microstructure And Mechanical Properties Of Ultra-High Strength Steels, Rogerio Antao Cardoso

Doctoral Dissertations

"A martensite-based and an austenite-based Fe-Mn-Al steels were investigated aiming the pilot-scale production of steels that meet military specifications for Rolled Homogeneous Armor (RHA) and High-hardness Armor (HHA) plates. Each material underwent specific thermomechanical processes and the following hardness, Charpy V-notch (CVN) impact toughness at -40 °C and room-temperature tensile properties were correlated with the resulting microstructures.

Specimens of the martensitic steel were austenitized at 1010 °C, quenched and tempered at 150, 175, 200, 225 and 250 °C for times up to four hours. As for the Fe-Mn-Al steel, its hot rolling schedule was design to promote strain accumulation in …

Selected Topics In Blockchain-Aided Iot Inference, Yiming Jiang

Doctoral Dissertations

"Blockchain has recently been considered in the Internet of Things (IoT) to secure data exchanges and storage across various engineering applications. This newly emerging blockchain-aided IoT (BIoT) network has been applied to a great deal of security-related applications. However, the BIoT still has the vulnerability that can be exploited by attackers, potentially impairing the performance of BIoT applications. Despite this, research addressing the vulnerability has been limited. This work presents four studies aimed at addressing critical gaps in current BIoT research.

The first study introduces a Time-Restricted Double-Spending Attack (TR-DSA) model for Proof-of-Work (PoW)-based blockchains, where the adversary only conducts …

Drone-Based Multimodal Sensing On Vegetations And Data Analytics For Early Detection Of Gas Leakage From Underground Pipelines, Pengfei Ma

Doctoral Dissertations

"This study explored the feasibility of using multimodal remote sensors in the early detection of natural gas leaks from underground pipelines, as vegetation situated above pipelines can discern microbial changes in soil when affected by gas and exhibit physiological stress symptoms on leaves. Three sensors (RBG, thermal, and hyperspectral cameras) were utilized to monitor vegetation stress as an indicator of gas leaks. A laboratory experiment was conducted to evaluate the workability of vegetation for gas leak detection. Regular hyperspectral imagery was collected from test vegetations to identify gas stress and distinguish it from other environmental stressors such as salinity impact, …

Sensor Embedding And Thermal Monitoring Strategies For Laser-Foil-Printing Additive Manufacturing, Tunay Turk

Doctoral Dissertations

"This work investigates Laser Foil Printing (LFP), a novel metal additive manufacturing (AM) process that fabricates parts layer-by-layer using metal foils. To enhance LFP productivity, the process steps were optimized, and an 88.1% reduction in processing duration was achieved. A unique aspect of this study was the introduction of laser polishing as an edge polishing technique within the LFP process. This innovative approach, employing an overlapping spiral pattern, leverages selective laser remelting and erosion to effectively suppress elevated edges. To stabilize the molten melt pool, a discrete spot scanning strategy was implemented. The fabricated parts were subjected to detailed analysis, …

Processing And Densification Of Multi-Phase High-Entropy Ceramics, Steven Smith

Doctoral Dissertations

"This work focuses on the processing and densification of multiphase, high-entropy ceramics to promote their use in friction stir welding technologies. Several high-entropy systems including high-entropy borides, carbides, and their composites were produced. Boro/carbothermal and carbothermal synthesis were used to produce high-entropy powders from oxide powder mixtures. Composites of high-entropy borides and high-entropy carbides were produced using a sequential approach to produce both phases. The carbide was first produced using carbothermal reduction, then ZrH2 and B4C were added to the carbide powder to produce the high-entropy boride phase. The resulting powder was densified by spark plasma sintering and pressureless sintering, …

Raft-Based Polymer And Nanoparticle Materials For Traumatic Brain Injury Treatment And Diagnostics, Aaron Priester

Doctoral Dissertations

"Traumatic brain injury (TBI) is a leading cause of death and disability worldwide. Neurodegenerative diseases that develop post-TBI can be, in part, attributed to DNA and cell-damaging reactive oxygen species (ROS) and lipid peroxidation products (LPOx). This thesis focused on overcoming the limits of current TBI material treatment approaches by employing a RAFT (reversible-addition fragmentation chain transfer) polymer approach that incorporated novel therapeutic, diagnostic and peptide-targeting monomers. An improved nanoparticle synthesis approach was also developed. Thiol and thioether-containing monomers neutralize both ROS and LPOx while Gd-containing monomers with enhanced magnetic resonance imaging (MRI) contrast provide diagnostics and material tracking in …

A Hybrid Data Processing, Computational Intelligence, And Complex Systems Modeling Approach For Describing And Predicting The Bitcoin Market, Oluwadamilare Akinpelu Omole

Doctoral Dissertations

"The Bitcoin market, like traditional financial markets, is a complex system with intricate interdependencies and nonlinear interactions among various market elements. This, coupled with the inherent uncertainty and high volatility present, makes predicting Bitcoin price movements difficult. The lack of understanding of the underlying market dynamics often results in significant losses for investors and traders. Existing studies have focused on the use of predictive models, which have not sufficiently captured the complexities of the market and cannot forecast extreme market events. This research endeavors to bridge this gap by combining data processing techniques, computational intelligence, and complex systems theory to …

Atmospheric Transport Of Radionuclides, Meteorological Data Mining & Synthesis For Site Data Supplementation, Ben Yao Sonpon

Doctoral Dissertations

"This research aligns with the NRC's vision of implementing risk-informed decision-making to support its regulatory charter. The suite of tools developed includes automated procedures for data mining and extracting meteorological (met) data from various national and regional repositories. A second data analytics tool automates the process of data fusion into a uniform format while preserving data fidelity. Autocorrelations were then established, and correlation coefficients were calculated between the Callaway Nuclear Power Plant (Callaway) and nearby off-site weather stations. The complexity of these correlations depends on factors such as physical proximity, geographic features, and topology, potentially necessitating multivariate analysis (MVA). Furthermore, …

Oxidation Behavior Of Silicon Carbide, Matrix Graphite, And Refractory Multi-Principal Element Alloy, Visharad Jalan

Doctoral Dissertations

"The present study focuses on the investigation of the oxidation behavior of silicon carbide, matrix graphite in a water vapor environment. It also examines the oxidation behavior of refractory multi-principal element alloys when exposed to air. The oxidation behavior of silicon carbide and matrix graphite were investigated in conditions pertaining to off-normal incidents in high-temperature gas-cooled nuclear reactors. Understanding this is crucial for the prediction of their performance in such accidents and ensuring that the nuclear reactor is accident tolerant. Upon exposure to water vapor, the two A3-based matrix graphite exhibited different behaviors. The A3-27 type showed oxidation in all …

Shock Wave And Vortex Ring Dynamics From Explosively Driven Shock Tunnels, Rachel Louise Bauer

Doctoral Dissertations

"Blast and shock tubes are frequently used to create shock waves to study their effects and impacts on structures, humans, and personal protective equipment. These tubes are also found in other industries including wind tunnels for aerodynamic testing, jet engines for propulsion research, spacecraft reentry simulations, and industrial applications such as material testing and high-velocity impact studies. Despite their widespread use, there is no standard design, with variations in geometry, size, and energy sources. Current research only evaluates the peak pressure of the shock wave produced and does not consider the effects of changing the size or geometry of the …

The Evolving Use Of Strategic Planning Tools In The Manufacturing Environment: Implications For Quality 4.0 And Beyond, Richard Lee Wilson

Doctoral Dissertations

"Having a strong strategic plan is critical for success for any business no matter the size of the organization, the product or service they provide, or the industry they serve. There are many methods businesses use to develop their strategic plans. One such method is known as Hoshin Kanri, which has been in use for decades. However, recent years have seen an increase in artificial intelligence, big data, data analytics, and other technology tools to create cyber physical systems on the manufacturing floor. The increase in technology in manufacturing to integrate cyber systems with physical systems spawned a new industrial …

Transport And Plugging Behavior Of Co2-Resistant Preformed Particle Gels In High Conductive Channels For Conformance Control, Adel Alotibi

Doctoral Dissertations

"Improving oil recovery is essential with rising global oil demand and declining production in mature fields. CO₂ flooding has been widely applied as a major Enhanced Oil Recovery (EOR) method due to its effectiveness in boosting oil recovery while enabling safe carbon storage in the subsurface. However, in fractured and highly heterogeneous reservoirs, CO₂ often flows through paths of least resistance, leading to early breakthrough or quick excessive CO₂ production and leaving substantial oil in unswept zones or areas. Traditional in-situ polymer gels have been applied to control CO₂ flooding conformance, their performance has been varied, …

Development And Testing Of Irradiation-Tolerant High-Entropy Alloys, Matthew John Luebbe

Doctoral Dissertations

"High entropy alloys (HEAs) are a novel class of alloys made of multiple principal elements in near equal proportions. They have been observed to possess an array of useful engineering properties, such as good ductility and fracture toughness, high temperature strength, oxidation and corrosion resistance and irradiation resistance. This makes them promising candidates for harsh environments, especially nuclear reactors. These properties could potentially realize advanced Gen IV nuclear reactor designs. However, most HEA compositions contain Co, which activates under irradiation, generating safety and waste management concerns. This work studies three compositions of Co-free HEAs whose strength and microstructures are evaluated …

Investigation Of Shockwave Behavior To Inform Helmet Design Using Schlieren Imagery And Free-Field Blasts, Cody Jh Thomas

Doctoral Dissertations

"Ballistic resistance of military helmet designs is a prioritized feature to protect warfighters from traumatic brain injury. However, injuries from shock-based threats have not been optimized for warfighter protection and have resulted in the prevalence of blast-induced traumatic brain injury (bTBI). Research gaps were identified in understanding the under wash effect using free field blasts and schlieren imagery. Thus, the following were investigated: (1) overpressure changes on a warfighter’s head due to directionality from a blast, (2) shock wave dampening effects of viscoelastic materials in helmets, and (3) geometric effects of a helmet brim design in the reduction of bTBI. …

Nmr Relaxometry Approach For The Detection Of Asphalt Binder Performance Properties, Rebecca Herndon

Doctoral Dissertations

"Asphalt is a necessary material for transportation infrastructure. Understanding the material properties of asphalt binders is critical for improving infrastructure and enhancing the lifetime of pavements. While the physical properties of asphalt binders are well-defined by standard procedures and parameters, the chemical environment lacks definition. Physical parameters like viscosity and stiffness are traditionally used to differentiate asphalt binders, describe aging, and indicate the impact of additives. However, these tests have limited insight into the material's chemical environment. Therefore, a nondestructive analytical technique, nuclear magnetic resonance (NMR) relaxometry, was employed to investigate the chemical environment of asphalt binders. Although NMR relaxometry …

Vibration Modeling Of Rectangular Plates And Application To Solar Cell Dust Mitigation, Jeremiah John Rittenhouse

Doctoral Dissertations

"Many engineering structures can be modeled as rectangular plates, including solar cells. Carefully controlled plate vibration can be useful to solve an engineering problem, such as lunar dust accumulation on solar cells, which blocks light and reduces power generation. For this application, plate vibration at resonance is studied and used experimentally to eject lunar dust from a solar cell.

Piezoelectric actuator placement on the inactive side of a solar cell to induce vibration dust mitigation from the active side of the cell is presented in this work. Three solar cell prototypes were created and tested for efficacy, resulting in an …

New Topologies For High Voltage Gain Dc-Dc Power Electronic Converters – Theoretical Analysis And Experimental Validation, Saeed Habibi

Doctoral Dissertations

"This dissertation is focused on developing and analyzing new high voltage gain DC-DC power electronic converters. The proposed converters in this dissertation are suitable candidates for connecting low voltage sources such as photovoltaic (PV) panels or fuel cell (FC) stacks to a DC microgrid or DC link of an inverter. The proposed converters provide desired characteristics such as high voltage gain at a low or medium duty cycle values, low voltage stress on power semiconductors, and continuous input current. Initially, the research introduces three novel converter topologies: First, two quadratic converters based on the combination of a three-winding coupled inductor …

Characterization And Modeling Of Properties Of Unsaturated And Partially Damaged Cement-Based Materials, Rezwana Binte Hafiz

Doctoral Dissertations

"Transport properties, governing the resistance of cement-based materials to harmful substances are essential considerations for long-term performance. This study addressed the often-overlooked dimension of transport properties in unsaturated cement-based materials, crucial as most concrete structures face variable environmental conditions, leading to partial saturation. A two-scale model was introduced, enhancing our comprehension of transport properties in conditions reflecting real-world scenarios. Empirical correlation representing bulk paste characteristics was established, facilitating the upscaling of properties to mortar and concrete. The model was extended to predict the transport properties of mortar as well.

Environmental factors can contribute to the degradation of cement-based materials, with …

Advancing Refuge Alternatives In Mine Emergencies Using Advanced Numerical Simulation, Kutay Emre Karadeniz

Doctoral Dissertations

"Incidents and emergencies within underground coal mines can result in severe injuries or even loss of life, particularly due to the hazardous nature of mine explosions. One of the options for the miners to protect themselves from these hazards is to be sheltered in a refuge alternative (RA). However, the literature lacks an analysis of survivability constraints and the structural integrity of RAs when exposed to geomechanical changes and the ability to withstand the impact of coal mine explosions. In this study, based on the utilization and survivability constraints, basic human requirements and the required physical specifications of RAs during …

Additive Manufacturing Of Multifunctional Materials And Composites, John Michael Pappas

Doctoral Dissertations

"This research focused on developing fundamental knowledge of process-material interactions for additive manufacturing of multifunctional materials that are highly desirable in high-tech industries for potential weight and space savings. Multifunctional materials are very sensitive to defects, which severely hinder performance. Thus, defect formation was systematically studied to develop strategies and methodologies to efficiently fabricate high-performance materials and composites. Blown-powder-based laser additive manufacturing of transparent spinel ceramics was investigated to reduce porosity and cracking, defects that hindered transparency and mechanical properties. A systematic study of processing parameters revealed that laser power and powder flow rate had the largest effects on defect …

Experimental Investgation Of Core Fluid And Heat Transfer Of Pwr By Using Advanced Measurments Techniques, Saud Aldawood

Doctoral Dissertations

This comprehensive study investigates the thermal-hydraulic mechanisms and convective heat transfer characteristics within (PWRs), with a focus on (SMRs) under both single-phase and two-phase bubbly flow conditions. Specifically, the research investigates the complex bubble dynamics in two-phase flow rod bundles, which are crucial for understanding reactor behavior during loss-of-coolant accidents (LOCA). Employing an advanced experimental setup developed at the (mFReel) at MST, this work measures critical parameters such as void fraction, bubble passage frequency, bubble velocity, bubble chord length, and interfacial area concentration (IAC) using a four-tip optical probe across various locations in the rod bundle. The findings reveal that …

Nano-Micro Engineering For Advanced Energy Devices, Tazdik Patwary Plateau

Doctoral Dissertations

The development of advanced materials and manufacturing techniques for energy storage devices is continuously growing. The research emphasizes micro-engineering, nano-engineering, and advanced materials science, with the goal of enhancing the performance and scalability of manufacturing methods of different materials processing with a view of achieving sustainability. In the micro-engineering domain, novel methods for fabricating thick electrodes with short diffusion paths are introduced, enabling higher mass loading and improved battery performance. Additionally, innovative strategies for optimizing the performance of carbon nanofibers (CNFs) as anode materials in LIBs are explored in the nano-engineering domain. These studies address key challenges such as inter-bonding …

Ceramic Dielectrics For High Temperature Capacitor Applications, Alan Daniel Devoe

Doctoral Dissertations

Technical progress in microelectronics is allowing operation in environments that were previously considered impossible. Building complete electronic circuits for applications above 450 degrees C, such as the planned NASA missions to Venus, require a variety of active and passive components, including multilayer ceramic capacitors (MLCC).

This study explores calcium zirconate CaZrO3 and magnesium oxide MgO based dielectric compositions for MLCC applications that are capable of operating at extreme temperatures between 450 degrees C and 600 degrees C. Both materials were characterized with respect to impurities, dopants, crystal structure and microstructural development. Dielectric properties were measured to determine permittivity, dissipation factor, …