Engineering Commons^™

A Study Of Viscous Frictional Effects And Relay Characteristics On The Operation Of A Positional Relay Servomechanism, Earl F. Richards

Masters Theses

"The thesis describes some experimentally observed data and analytical approaches to the study of a relay servomechanism. The experimental data were secured from an analog simulation of a relay servo system. The results of this data were compared to the transient approach by use of the phase-plane method. The stability of the system was determined using a describing-function. The analytical approaches are described in the presentation.

A study of the effects of viscous friction is described, and the characteristic of the relay used in the system is given special attention. The response to input driving function was considered, and rise …

A Systematic Study Of Experimental Parameters In A Cloud Chamber Search For Subionizers, Zin Aung

Masters Theses

"Since there is no theoretical basis for the quantization of electric charge, it is reasonable to consider the possible existence of particles with charges much less than the electronic charge ‘e’. Such particles, if they exist, are expected to ionize more lightly than the electron. Similar remarks hold true for particles with electric dipole moments, and relativistic monopoles with strengths much less than ’e’ electrostatic units. These particles have been termed subionizers.

The selection of apparatus for a subionizer search has been discussed. The desired conditions for such a search using a low background, long sensitive time Wilson cloud chamber …

Temperature Distribution In An Infinite Plate As A Function Of The Input Heat Flux, George Franklin Wright

Masters Theses

"It is the purpose of this thesis to investigate the effects of a variable input heat flux impinging equally on both sides, on the temperature distribution within an infinite plate. An infinite plate may be defined as one in which the dimensions are infinite in two directions and finite in thickness. For practical purposes such a plate could be thought of as one in which the thickness was small enough, compared to the other two dimensions, so that a temperature gradient exists only normal to the surfaces of the plate. This assumption will be made to establish one-dimensional heat flow …

Correlation Of Dust-Count Results By Zeiss Konimeter And Midget Impinger, Chandmal Jain

Masters Theses

"In this modern age, the scientific and technological developments have advanced mechanized mining to the status wherein the attendant dust problems have reached very serious hazard proportions. The significant roles, which have been perfected for the Zeiss konimeter and the midget impinger, in evaluating dust concentrations and thereby revealing possible improvements in making the atmospheric conditions safer, cannot be over emphasized.

While introducing the subject of this paper in the first chapter, the author has presented a historical resume, wherein he pointed out that performances of these instruments have not been correlated in the past. However, the work reported on …

Design, Construction And Operation Of Equipment For The Study Of Evaporation Of Aqueous Solutions Using A Simplified Reactor Design Approach, Virendra Kumar Mathur

Masters Theses

"The study of simultaneous heat and mass transfer in flow reactors has attracted the attention of many workers for a long time due to its wide application in the industrial field. These heat and mass transfer studies play an important role in determining the rate equations and in turn the size of the reactor itself. A large number of chemical reactions have been studied by various workers….

The purpose of this work comprised only the initial or exploratory phase of this overall project, and deals with the design, construction and assembling of the equipment necessary to carry out the vaporization …

A Heterocyclic Alkyd Resin, Bhailalbhai M. Patel

Masters Theses

" 'Alkyd’ is a word coined by Kienle in 1927 to designate a class of synthetic resins which include the complexes resulting from the reaction of polyhydric alcohols and resinifying carboxylic organic aromatic acids or their anhydrides. The word in a broad sense is generally considered to apply to many modifications of these resins - drying, semi-drying and non-drying oil-modified alkyds. It was derived from the words alcohol and acid by combining “al” and “cid” and for euphony changing the ”cid” to “kyd” – al(cid)kyd.

Compounds having rings composed solely of carbon atoms are called homocyclic compounds or carbocyclic compounds. …

A Method Of Estimating Groundwater Influx Into A Vertical Mine Shaft, Morris T. Worley

Masters Theses

"Prediction of groundwater influx into mine openings is one of the more important pre-development problems encountered in mining. A satisfactory method of estimation would provide the information necessary for a mining company to dewater prior to shaft sinking, pre-grout the shaft area, or plan pumping schemes to handle the expected flow.

A standardized field method of estimating groundwater supply from pumping test data was developed by O. V. Theis and others. In the present research problem, the estimation procedure has been simplified by the use of nomograms. Certain modifications in the estimate must be made when a pumping well is …

A Dissolution Rate Study Of Beryllium In Hydrofluoric Acid, Donald Lee Mathis

Masters Theses

"Beryllium was shown to react stoichiometrically with HF, HCl, and H₂SO₄ acids in accordance with a plus two valence. These reactions were investigated by the hydrogen evolution method.

Dissolution rates were determined in five concentrations, 0.01, 0.05, 0.10, 0.50, and 0,75 N, of HF acid at 10, 20, 30, 40 and 50°C, This was accomplished by the hydrogen evolution method and the results were based on the tested stoichiometry. Beryllium has a high dissolution rate in HF acid, which approximates the following under similar conditions: 10 times Al, 4 times Ti, and 1.5 times Zr. A kinetic …

A Geophysical Investigation Of An Area In Christian County, Missouri, Edwin J. Ballantyne Jr.

Masters Theses

"A vertical intensity magnetic survey of 144 square miles in Christian County, southwest Missouri revealed an 825 gamma anomaly having a closure of 9 square miles. A three mile gravity traverse across the magnetic anomaly detected a positive gravity anomaly in excess of six mllligals.

Calculations showed that a Precambrian hill large enough to cause the observed magnetic anomaly would outcrop at the surface. Because Precambrian rocks are known to be buried under a sedimentary layer, this hypothesis was rejected.

Theoretical anomalies of several geometrical bodies at calculated depths were visually compared with the measured magnetic and gravity profiles. A …

Specification For The Design Of Light Gage Cold-Formed Steel Structural Members, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

A Study Of The Inlet Characteristics And Entrance Losses Of Pipe Culvert With A Flush Mounted, Sharp Edged Inlet, Luke Lea Callaway Jr.

Masters Theses

"Of all hydraulic structures, culverts are by far the most numerous. Lack of understanding of the functioning of culverts has resulted in many of them being implaced improperly and as a result, they function with less efficiency and at reduced capacity. Much has been written regarding the flow of water in open channels, culverts included, but little has been done regarding inlet conditions. It is necessary in the design of culverts, as with any other structure, that conditions which govern the operation of the structure be established. This paper is a study of the inlet conditions of a circular cross …

A Method Of Design For Spiral Reinforced, Eccentrically Loaded, Concrete Columns, Lloyd O. Senter

Masters Theses

"This thesis presents a method of designing spiral reinforced, eccentrically loaded, concrete columns on the basis of the 1957 American Association of State Highway Officials specifications.

Equations from AASHO, in conjunction with equations derived in this thesis, are programmed for and solved by the IBM 650 digital computer. The data obtained from the computer is plotted such that, given the normal load and moment on a column, the minimum required area or reinforcing steel may be read directly from the graph.

The derivation or equations, the computer program, and the graphs are included in the thesis"--Introduction, page 1.

Heat Transfer Coefficients In Artificially Roughened Pipes, Mehmet Hayati Turan

Masters Theses

"The purpose of this investigation is to determine experimentally the effects of three different types of artificial roughness on the convective heat transfer coefficient in a pipe and compare these values with that for a smooth pipe for turbulent flow"--Introduction, page 7.

Temperature Distribution In A Semi-Infinite Solid As A Function Of The Input Heat Flux, Lloyd Carl Laciny

Masters Theses

"In this thesis the problem of varying heat flux into a semi-infinite solid initially at zero temperature is investigated. Varying heat flux means that the heat transferred to the solid by its surroundings is a function of time; in this particular problem it is chosen to be an exponential function of time. A semi-infinite solid is one which is bounded by only one plane.

This subject has achieved considerable importance in the field of space technology. A body in space is beyond the realm of aerodynamic heating and non-uniform skin temperatures reached as a result of radiation from a high …

Some Dynamic Creep Characteristics Of Gypsum, Ikram-Ul-Haq Dar

Masters Theses

"A review of literature concerned with time-dependent deformation of geologic and non-geologic materials is presented. A static loading machine and a four unit dynamic loading unit was designed and assembled to evaluate static and dynamic creep properties of gypsum. The tests were run for various levels of static loads, and superimposed dynamic loads. Investigations were carried out to determine the relationships, if any, between impact energy, impact velocity and momentum, and dynamic strains. Viscoelastic coefficients were determined for the investigations. The conclusion was presented that time-dependent strain in the dynamic creep tests of the particular gypsum rock tested is a …

Heat Transfer In A Vortex Flow Metal To Air, Elisha Rachovitsky

Masters Theses

"In this study heat transfer in a vortex flow has been investigated experimentally and analyzed qualitatively.

Air was forced through a Ranque tube in order to get a swirling turbulent flow in its "hot" section. The test section, having a diameter of .355 inches and a length of 27.5 inches, was heated by an induction coil.

Three types of flow were under investigation: a linear turbulent flow, a vortex uniflow and a mixed vortex-linear turbulent flow.

The experiments covered a range of tube-wall temperature from 570 to 900 Deg. R and inlet pressure to the vortex generator ranged from 25 …

Methods For Calculating The Minimum Amortization Tonnage And Maximum Present Value For An Ore Body, Garrett M. Sainsbury

Masters Theses

"The discussion is divided into three parts. Part I describes a procedure for determining the mining rate that gives the minimum amortization tonnage required of an ore body, and the amount of that tonnage. The basic idea is that amortization tonnage is equivalent to the estimated capital costs, including interest, divided by the estimated operating profit per ton. Both capital costs and operating profit per ton can be expressed as functions of mining rate by making use of empirical equations. Therefore, amortization tonnage can be expressed as a function of mining rate. The amortization tonnage is calculated for a series …

High Temperature Oxidation Of Nickel, Virgil R. Friebel

Masters Theses

"Using a sensitive volumetric technique, a study was made of the kinetics of oxidation of nickel at 1200° C. and 1300° C. Three purities of nickel were used for the investigation which was limited to the initial three hours of reaction.

The rate of oxidation of nickel followed the parabolic rate law after an initial period of deviation which lasted up to 40 minutes. No direct correlation was found between the oxide thickness and the end of the period of deviation from the parabolic rate law.

The purity of the nickel was found to have a marked effect on the …

The Constitution Of Magnesium-Rich Magnesium-Zirconium Alloys, Kenneth Allen Fowler

Masters Theses

"The magnesium-zirconium system has been studied to 0.8 per cent zirconium which represents the limit of solubility of zirconium in liquid magnesium at 950°C. Alloys have been prepared by two methods of alloy additions, and the results compared. Microstructural studies have been made of the alloys in the cast, extruded, and heat-treated conditions. The limit of solid solubility has been determined on the basis of resistivity and temperature coefficient of resistivity measurements, as well as by metallographic examination, with good agreement. A secondary structure resulting from precipitation of a second phase within cored regions of the alloy has been studied …

The Redesign And Construction Of A Rotating Disc Contactor, Richard Henry Okenfuss

Masters Theses

"Liquid-liquid extraction has played a major role in the processing of nuclear fuels. The Department of Chemical Engineering of the Missouri School of Mines and Metallurgy realizing this, petitioned the Atomic Energy Commission for funds to design and construct an instructional facility representing the chemical processing of nuclear fuels. With this unit and its solvent recovery equipment, in which stress is placed on extraction and distillation, not only are the principles of nuclear fuels processing demonstrated, but the more basic concepts of mass and energy transfer are also illustrated. Extraction depends upon solubility differences to achieve a transfer of a …

The Effect Of The Rare Earth Elements On The Hot Workability Of Ingot Iron, L. A. Neumeier

Masters Theses

"The effect of mischmetal and rare earth oxides on the hot workability of ingot iron in the hot-short region was studied. Thirteen heats were melted in air in a basic-lined induction furnace. All heats were thoroughly deoxidized with aluminum prior to the rare earth additions. Mischmetal was added in amounts of 0.1, 0.3 and 0.5 per cent. Rare earth oxides were added in amounts of 0.1 and 0.2 per cent. Temperatures were maintained at approximately 2900°F and holding intervals between mischmetal additions and pouring at two minutes. Bars were hot rolled and swaged for hot twisting in the hot-short region. …

Determination Of Vapor-Liquid Equilibrium Data By Continuous Distillation, David William Bunch

Masters Theses

"The procuring of experimental vapor-liquid equilibrium data has been a problem of considerable importance to chemical engineers for a number of years. Modern distillation theory and practice have made accurate vapor-liquid equilibrium data practically a necessity.

Using conventional methods for determining vapor-liquid equilibrium data, an experimenter can obtain only a single vapor-liquid equilibrium composition per trial. Ramalho working with Tiller has developed a new method which makes possible the determination of all values of the vapor and liquid concentrations in a single experiment.

The work done by Ramalho indicated that the necessity for very precise temperature measurements presented a serious …

Segregation Method As Possible Process To Beneficiate Oxidized Lead Ores, Jose Molfino Tomasio

Masters Theses

"In this investigation it has been demonstrated that the Segregation Process has merit for treating oxidized lead ores.

The process comprises heating the crushed ore with salt and coal at about 750° C. to produce metallic lead attached to the carbon particles, which then is recovered by conventional flotation methods.

The quantities of sodium chloride and coal required for the best segregation of lead obtained in this work was 1.0 percent of coal and 1.0 percent of salt by weight.

Good segregation was obtained by using salt and coal as fine as 65 or 48 mesh. Segregation varied with the …

The Separation Of Selected Radioactive Fission Products By Electrodialysis, Jerry David Vie

Masters Theses

"The recent advent of nuclear energy has opened an era of almost unlimited power and countless problems. A problem of extreme importance is the recovery of unburned nuclear fuel and the claiming of transmutation products, such as Pu²³⁹ and U²³³, from the irradiated fuel elements. The chemical processing must also separate the fission products from the fissionable material if the fuel is to be used again.

At present, the irradiated fuel elements are stored for 90 to 120 days to allow the intense short half-life activity to decay. After "cooling down", the nuclear fuels are separated from …

Water Resources Development -- An Analysis Of Economic Justification Practices Of The Corps Of Engineers, Kerwood W. Barrand

Masters Theses

"Presented herein is a brief analysis of the economic justification practices of the Corps of Engineers as commonly implemented in proposals concerning water resources projects. Where applicable, recommended methods are compared to similar methods advocated for, and accepted by, private engineering firms in similar situations.

The major problem exists in the lack of a profit motive in programs undertaken with the use of public funds. However, a profit can be said to have been realized in public works programs if the total benefits of the programs to all the people exceed the costs of these programs and, further, if the …

An Experimental Investigation Of Receiver System Sensitivity, James Henry Johnson

Masters Theses

"A method of determining the minimum detectable power density incident at the receiving antenna of a UHF receiver is proposed. The minimum detectable power density is the power density required to produce a signal-to-noise ratio of unity in the output of the receiver. The proposed method includes the receiving antenna impedance, the necessary connecting transmission lines, and the receiver impedance.

It is shown that an error in the antenna directivity will produce a significant error in the overall sensitivity of a receiving system. Since the directivity is the most difficult system variable to determine experimentally, it is probably the limiting …

Physical Property Tests Of Rock, Centrifugal Tests And The Design Of Underground Mine Openings, Samuel Shu Mou Chan

Masters Theses

"Proper design of stable underground mine openings is important to the mining industry today. Various methods have been utilized by investigators to approach this goal.

A review of previous investigations of each of the phases of underground mine opening stress analysis is presented.

An approximate method of designing underground mine structures based on estimation of the initial stress field, rock physical property tests, and model tests, together with preliminary field data, is presented, and a specific example given"--Forward, page i.

A Method Of Fuel Testing In A Cfr Engine, George R. Baumgartner

Masters Theses

"At the present time, only a very small fraction of motor fuels produced for domestic use in the United States contain any alcohol in their blends. Soma foreign markets, notably the Philippine Islands and South American Countries use high proportions of alcohol in their motor fuel blends. Special purpose fuels in the United States which have alcohol blended with other compounds, have been used for engines from which maximum horsepower output is imperative. An example of this type of motor fuel blend might be found in the competitive motor sports involving motorcycles, stock automotive equipment, and special racing equipment.

An …

Stress Distribution In Splined Shafts In Torsion By The Membrane Analogy, Charles L. Edwards

Masters Theses

"The purpose of this investigation is to determine torsional shearing stress distribution in various shapes of shafts. The project will include shafts with circular boundaries. No attempt will be made to show the relation between stress and applied torque"--Preface, page iii.

Construction Of A Pulsed Perforated-Plate Extraction Unit, Clarence James Vetter Jr.

Masters Theses

"Liquid-liquid extraction is an important operation in the production and reprocessing of nuclear fuels. In the purification of uranium by liquid-liquid extraction, uranyl nitrate is separated from impurities by extraction into an organic solvent, followed by re-extraction into an aqueous phase. Further processing of the aqueous uranyl nitrate solution is tailored to yield uranium metal or any desired uranium compound.

In order that students in nuclear and chemical engineering may have an understanding of the practical as well as theoretical aspects of liquid-liquid extraction, a model of a uranium purification plant was designed and built in the Unit Operations Laboratory …