Engineering Commons^™

Alternating Current Method Of Measuring The Electrical Conductivity Of Dielectric Liquids, Henry E. Fischer, Ralph S. Carson

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Existence Of Two Types Of Drag Reduction In Pipe Flow Of Dilute Polymer Solutions, Harry C. Hershey, Jacques L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

Drag reduction in the pipe flow of polymer solutions is shown to be of two types which apparently occur by two separate mechanisms. In turbulent flow, drag reduction is probably caused by viscoelastic effects. The critical solvent Reynolds number at the onset of drag reduction is proportional to about the first power of the diameter. Thus, the critical velocity is independent of tube diameter. Polymers dissolved in good solvents show more drag reduction than in poor solvents. The other type of drag reduction occurs when the laminar region is extended to high Reynolds numbers. It is followed by a transition …

Numerical Differentiation Of Equally Spaced And Not Equally Spaced Experimental Data, Harry C. Hershey, Jacques L. Zakin, Robert Simha

Chemical and Biochemical Engineering Faculty Research & Creative Works

Procedures are given for smoothing and differentiating experimental data with both equal and nonequal spacing in the independent variable. Selection of the number of points to be included in the "movable strip" technique and of the degree of the polynomial is discussed. Equations are given to estimate the error by calculating a confidence interval on each slope. A technique for handling certain types of nonrandom errors is presented. © 1967, American Chemical Society. All rights reserved.

Strength And Behavior Of Light-Gage Steel Shear Diaphragms, Larry D. Luttrell

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

Light-gage steel roof, wall, and floor systems may be used to transfer in-plane shear forces from one part of a framed structure to another, leading to reduced loads in parts of the structure. Such behavior is particularly noticeable in buildings that have rigid shear walls and are subjected to lateral loads such as those arising from wind or earthquakes. The transfer of shear force through such diaphragms is dependent on the shear strength and is particularly sensitive to shear stiffness. The stiffness of the diaphragm must be considered in relationship to the stiffness of the structural frame. Diaphragm response to …

Trace Element Content Of Magnetites And Hematites, Southeast Missouri Iron Metallogenic Province, Usa, Geza Kisvarsany, Paul Dean Proctor

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Six major and numerous smaller Precambrian iron deposits of mag-matic origin occur in the volcanic rocks of the Southeast Missouri Iron Metallogenic Province in an area approximately 70 miles long and 40 miles wide. The Precambrian igneous complex is composed of mainly high silica, with some intermediate, volcanic rocks intruded by granitic rocks and some diorites and gabbros. Biotite schists occur locally. Some of the volcanic and intrusive rocks are characterized by an unusual abundance of alkali metals. Local enrichments in fluorite, calcite, and iron oxides are present. The shapes of the iron deposits range from massive tabular to irregular. …

Vaporization Through Porous Membranes, Marshall E. Findley

Chemical and Biochemical Engineering Faculty Research & Creative Works

Mixtures may be evaporated from one interface of a Non wettable porous membrane with diffusion through the vapor-filled pores and condensation at the other interface of the membrane, by a sufficiently higher temperature on the mixture side maintained by a heat supply to the mixture and heat removal from the condensate equal to the latent heat transferred with vapor plus heat transferred by conduction. This permits essentially infinite-stage flash evaporation at constant liquid pressures, either with diffusion through Non condensable gases in the pores, or with vapor flow at a lower pressure than liquid pressures, but with liquids excluded from …

Variation In Gold Content Of Minerals Of The Marysville Quartz Diorite Stock, Montana, Erwin J. Mantei, Arthur H. Brownlow

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Neutron activation analysis for gold has been carried out on 135 mineral samples from throughout the Marysville stock with the following results: (1) the gold content of 44 biotite ranges from 0·002 to 0·924 ppm with an average of 0·076 ppm; (2) 37 hornblende samples gave a range of 0·003-0·823 ppm and an average of 0·100 ppm; (3) for 44 magnetite samples the range was 0·003-0·329 ppm and the average 0·037 ppm; (4) 10 quartz-feldspar samples varied from 0·006 to 0·176 ppm with an average of 0·065 ppm. High gold values mainly occur near the edge of the stock and …

Relationships Among The Metallurgical Condition, Hardness, And The Electrical Conductivity Of Aluminum Alloys, Richard A. Mueller

Masters Theses

"Electrical conductivity measurements (eddy current determined) combined with indentation hardness measurements are now being used throughout the aerospace industry for nondestructive evaluation of the metallurgical condition of commercial precipitation hardenable aluminum alloys. The review of literature and experiments with two aluminum alloys, 7178 and a 5% Zn-Al binary, have shown that skilled interpretation of hardness-conductivity data depends not only upon a qualitative understanding of the modern wave mechanical theories of electron conduction, but also upon some knowledge of the precipitation reaction kinetics. In particular, the effects of "quenched-in" vacancies and retrogression upon the reaction kinetics must be considered. Studies of …

Collision And Pursuit Course Terminal Closures For Spacecraft To Satellite Rendezvous, John Anthony Campbell

Masters Theses

"Collision and pursuit course closure maneuvers were studied for correcting position and velocity errors in the terminal phase of spacecraft to satellite rendezvous.

Minimum values of the ratio of initial range to velocity necessary to achieve rendezvous were determined for collision closures as a function of the initial line of sight. The time and velocity increment required for rendezvous were computed as a function of initial conditions.

Pursuit closure maneuvers were analyzed and time and velocity increments defined as a function of initial range, closing velocity, line of sight angle and angular velocity.

The velocity increments required were significantly higher …

Matrix Computer Analysis Of Curvilinear Grid Systems, David Leon Fenton

Doctoral Dissertations

"A general equilibrium-stiffness method of matrix structural analysis was adapted and applied to the solution of the member end forces and moments of each of the members in a curvilinear structural grid system. A structural system of this nature is commonly used as the supporting framework for a "steel-framed dome", in addition to being a basic structural component in many aerospace applications. An integral part of the development of the analysis was the development of a computer program to perform the many complex operations required to obtain the solution. The engineer, by supplying the appropriate structural data and load data …

The Transient Dynamics Of Plane Mechanisms, Navnit Chhaganlal Mehta

Doctoral Dissertations

"Accurate determination of dynamic characteristics of mechanisms has become more important with increased requirements on speed, efficiency and precision. Many devices, such as circuit breakers and computing mechanisms, operate under purely transient conditions and actuation time places a serious limitation on the response of the system of which these devices are a part.

In the classical analysis, whether it be graphical or analytical, the mechanism is assigned a specified position and state of motion from which the forces required to produce the motion can be determined. The inverse problem of specifying the driving force and determining the resulting motion, which …

Numerical Approximation To Performance Predictions Of Gas-Drive Reservoir With Or Without Gas-Cap And Gas Injection, Jagannath Rao Ghole

Doctoral Dissertations

"The pressure-saturation transient history for a hydrocarbon reservoir is solved for solution-gas, gas-cap and injected-gas drives assuming the saturation-pressure variations depicted by Muskat, under specific restrictive assumptions. A prototype reservoir system and its transient pressure saturation distribution under production is systemized on an IBM 360-Model 40 Computer which allows the definition of the transient behavior of saturation with pressure declination and fluid withdrawal for preassigned initial saturations of the oil, water and gas phases. This analysis is then modified for the existence of a gas-cap and for the re-injection of produced gas volumes for pressure maintenance considerations and the ensuing …

An Investigation Of The Creep Characteristics Of Portland Cement Mortar Under Static And Dynamic Strain, Ikram-Ul-Haq Dar

Doctoral Dissertations

"The combined effect of static and dynamic loads on design of underground openings is currently receiving much attention. It is known that the time-dependent behavior of rock is considerably different when a dynamic load is superimposed on prestressed rock. The shape of an underground opening has a definite influence on the magnitude of the local stresses and these may be significantly larger than those due to the weight of the overlying rock alone. Under these conditions, even a small dynamic load in the form of vibrations caused by blasting, drilling and related operations may increase the stress beyond a critical …

Handlos And Baron Model: Short Contact Times, J. Patel, Robert M. Wellek

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Radial Pressure Gradient In Turbulent Pipe Flow, Gary Kent Patterson, Walter J. Ewbank, Virgil A. Sandborn

Chemical and Biochemical Engineering Faculty Research & Creative Works

Measurements made with a Prandtl static pressure probe have demonstrated that a radial pressure gradient does exist in turbulent pipe flow with approximately the magnitude predicted by Sandborn from hot-wire anemometry measurements.

The Effect Of Concentration On The Viscosities Of Solutions Of Linear Flexible High Polymers, Lung Yu Chou, Jacques L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

Viscosity-concentration results in the moderately concentrated range for four samples of polyisobutylene (molecular weights of 1.3 x 104 to 1.0 x 106) in cyclohexane (concentrations up to 4.7 g./dl.) and in benzene (concentrations up to 7.0 g./dl.) at 24°C. (a theta solvent) showed molecular weight and goodness of solvent dependencies similar to those reported earlier for three other polymers. For polyisobutylene, polystyrene, and a copolymer of styrene and methyl methaerylate in good solvents, viscosity-concentration data plotted as ηsp. C[η] vs. k′[η]C fit a single curve. The linear region of this curve suggests that the Huggins equation is useful to C[η] …

Reviews Of Books And Papers In The Computer Field, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

Analysis Of The N-Wire Exponential Line, Edward C. Bertnolli

Electrical and Computer Engineering Faculty Research & Creative Works

A new approach to distributed network analysis is presented with the analysis of the n-wire exponential line as example. This approach provides the distributed network's transfer matrix in a form useful for both transient and steady-state network calculations. © 1967, IEEE. All rights reserved.

A Determination Of The Rate Of Evaporation Of Zinc At Atmospheric Pressure., Yu Ming Su

Masters Theses

"Measurements of evaporation rates of zinc in three different residual gases, e.g., argon, carbon monoxide, and hydrogen at one atmosphere pressure, were made. It was found that the rate of evaporation of zinc in one atmosphere of argon was almost the same as that in carbon monoxide, while the rate in hydrogen was almost twice the rate in argon or carbon monoxide. Measurements of evaporation rate of zinc in one atmosphere of argon-oxygen mixtures were also made. The evaporation rate was considerably reduced because the formation of the oxide film retards the zinc vapor escaping from the evaporating surface"--Abstract, page …

Hydrologic Characteristics Of Shallow Bedrock Aquifers In The Vicinity Of Norman Creek, Central Phelps County, Missouri, Michael A. Nawrocki

Masters Theses

"Groundwater is becoming increasingly important as a source of water supply in the United States. Consequently, the prediction of well yields is a vital concern. In order to predict the quantity of water which can be reduced from a given aquifer it is necessary to know the aquifer's hydrologic characteristics. Many theoretical formulae have been derived for determining the aquifer characteristics. To date, these formulae have been tested mainly on unconsolidated and clastic rock aquifers. It has never been shown that these formulae can also be consistently applied to carbonate aquifers which underlie regions of karst terrain. This paper summarizes …

The Anodic Dissolution Of Cadmium, James W. Johnson, E. Deng, S. C. Lai, William Joseph James

Chemical and Biochemical Engineering Faculty Research & Creative Works

The anodic dissolution of cadmium has been studied in aqueous solutions containing Cl−, Br−, I−, Ac−, SO₄=, and NO3− ions. The normal valence (+2) was found in all solutions with the exception of NO₃−. The apparent valence (calculated) of cadmium ions in nitrate solutions varied from 1.2 to 2.0 and was found to be a function of NO₃− concentration, current density, and temperature. An anodic dissolution mechanism has been proposed involving local corrosion and disintegration of the anode which is consistent with the experimental results. © 1967, The Electrochemical Society, Inc. All rights reserved.

The Role Of The Doctor Of Engineering Degree In Graduate Education, Wouter Bosch, Robert E. Carlile

Chemistry Faculty Research & Creative Works

No abstract provided.

Annealing Characteristics Of Neutron Irradiated Silicon Transistors, J. R. Chott, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

When a transistor is subjected to neutron irradiation, a component of base current proportional to neutron fluence is induced. From the effects of annealing on the base and collector Currents the conclusion was drawn that there is an apparent difference in the annealing characteristics between the neutral and the space-charge regions of the semiconductor device. This study of the anomalous annealing indicates that the neutron-induced component of base current is a result of one, or a combination, of the following mechanisms: A quasi-tunneling recombination phenomena in the emitter-base space-charge region, or an influence of the p-n junction electric field on …

Correction To “Analysis Of The N-Wire Exponential Line”, Edward C. Bertnolli

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

An Analytic Model For The Fluxgate Magnetometer, Stanley V. Marshall

Electrical and Computer Engineering Faculty Research & Creative Works

The output voltages from various fluxgate probe types are found to have the same general form, and an analytic model has been developed with which the output may be calculated. In the saturation region where the output pulse is developed, the differential permeability can be closely approximated by an exponential, dB/dH = k₁H^_k2, where k^_l and k^₂ are on the order of 100 and -2.0, respectively, for cores of Supermalloy or Permalloy 80. Using this model, the effect of the nature of the excitation function on output pulse amplitude and width and the effect …

The Design And Construction Of An Apparatus For The Plane Wave Analysis Of Mufflers, Stephen Philip Buckley

Masters Theses

"In the following report, a method for evaluating the attenuation characteristics of a general muffler as well as the design, construction and use of the associated apparatus are described. The method combines accepted plane wave theory and experimental techniques into a relatively straightforward approach to the analysis of acoustic filters. Equations are developed to cover the frequency range between 300 and 4000 cycles per second. Deviations from these equations extend the use of the equipment to low frequencies without the need for unduly long and cumbersome apparatus. This method, which may be called the standing wave method, utilizes a standing …

A Study Of Film Boiling Of Liquid Nitrogen And Liquid Argon Over A Wide Pressure Range With Cylindrical Heaters, V. J. Flanigan

Masters Theses

""A film boiling heat transfer study was conducted with three different diameter cylindrical copper heaters over a wide range of pressures for nitrogen and argon with the heat transfer surface in the horizontal position. The data were compared to the commonly used film boiling heat transfer relations. The common relations were found to be considerably in error for the range of variables covered in this investigation. A semi-empirical equation for corresponding states fluids which correlates the available data as a function of the reduced temperature and reduced pressure was derived and discussed"--Abstract, page iii.

Determining The Transfer Matrices Of Tapered Multiwire Transmission Lines, Clyde A. Vandivort

Masters Theses

"The advent of monolithic and integrated microelectronic circuits has aroused interest in passive multilayered thin film networks. The basic thin film network is shown in Figure 1. This structure consists of alternate resistive and dielectric layers sandwiched together. Such devices are referred to as distributed parameter RC networks. The reduction of volume and increased reliability offered by thin film devices has caused considerable effort to be extended in the analysis of their characteristics....

The incremental equivalent circuit given in Figure 2 stems directly from the above physical parameters and is the circuit used as a basis for the analysis that …

A Comparison Of Strength Properties Of Heat Treated Aisi 1065 Steels At High Strength Levels, Robert Lowell Hollenbeck

Masters Theses

"Six AISI C 1065 steels were heat treated and tensile tested in order to evaluate their ductility at high strength levels. Heat treating and tensile testing procedures were developed for use working with these steels at tensile strengths of 300,000 psi and higher. The austenitizing procedure in the hardening operation was found to affect the strength and ductility of the high strength samples. Rapidly heating to the austenitizing temperature followed by an immediate quench produced better properties than slow heating followed by a soaking period before the quench. However, it was concluded that the carbon contents of the steels studied …

A New Performance Index For Sensitivity And Energy Optimization., Mohamed Zafer Dajani

Masters Theses

"The principal aim of this thesis is to present a new index of performance which when minimized will simultaneously optimize the system energy and sensitivity function of a multivariable linear control system. With this performance index it is usually desirable to discriminate between the sensitivity factor and the energy term by weighting them differently. Two types of weighting factors are presented. Since it is not easy to minimize that performance index for all types of problems, further research is suggested to find methods of solution for such problems. Illustrative examples demonstrate the optimization process and the type of assumptions needed …