Engineering Commons^™

Ccfss News August 1991, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Interaction Of Sodium, Sulfur, And Silica During Coal Combustion, Thomas A. Erickson, Douglas K. Ludlow, Steven A. Benson

Chemical and Biochemical Engineering Faculty Research & Creative Works

The Interaction of Sodium, Sulfur, and Silica at Conditions Typical in a Pulverized Coal Furnace Was Investigated by using Both Model Mixtures and a Synthetic Coal. the Model Mixtures Consisted of Selected Inorganic Constituents that Were Well Mixed in Proportions Typically Found in Low-Rank Coal. the Synthetic Coal Consisted of a Furfuryl Alcohol Polymer with Appropriate Amounts of Sodium, Sulfur, and Silica to Duplicate the Characteristics of Low-Rank Coal. the Model Mixtures and Synthetic Coal Were Burned in a Laminar Flow (Drop-Tube) Furnace at 900, 1100, 1300, and 1500 °C and Residence Times of 0.1,0.5,1.5, and 2.4 S. the Resulting …

Tensile Strength Of Welded Connections, Wei-Wen Yu, Roger A. Laboube

CCFSS Library (1939 - present)

PREFACE The tensile strength of an arc spot weld is given only limited attention in the current edition of the AISI Specification for the Design of Cold-Formed Steel Structural Members. To broaden the design engineer's understanding of the behavior of arc spot welds, and to expand the specification's application for arc spot welds, the American Iron and Steel Institute, in 1989, initiated a research study at the University of Missouri-Rolla. The UMR research consisted of a comprehensive literature review, and experimental study which comprised of over 260 individual connection test specimens. The test specimen selection enabled the investigation of the …

Flexural Behavior Of Web Elements With Openings, Roger A. Laboube, Wei-Wen Yu, K. D. Batson

CCFSS Library (1939 - present)

INTRODUCTION The purpose of this phase of the research has been to investigate the flexural behavior of C-shaped members with web openings. Three common industry standard C-sections were tested as outlined in the first progress report. The web openings were located at 24 inches on center as illustrated in Fig. 1. Each test specimen was subjected to two point loads until the ultimate flexural strength of the member was obtained. This report summarizes the test procedure and results of the research to date.

Network Model Investigation Of Gas Transport In Bidisperse Porous Adsorbents, John H. Petropoulos, John K. Petrou, Athanasios I. Liapis

Chemical and Biochemical Engineering Faculty Research & Creative Works

A capillary network model consisting of a micropore network permeated by one of macropores of randomly varying size has been constructed. Although simplified (to keep computer space and time requirements low) in relation to a real bidisperse porous adsorbent or catalyst, it embodies the salient pore structural features likely to determine the gas-transport behavior of such porous solids. Suitable model calculations of Knudsen gas-phase and surface diffusion enabled us to (i) validate useful approximate methods for the more economical evaluation of network permeability and (ii) demonstrate certain important characteristic effects of nonrandom bidisperse pore structure on transport behavior and their …

Investigation Of Threaded Code, K. E. Graves, Paul D. Stigall

Computer Science Technical Reports

The design, structure and performance of threaded code are examined through the development of a threaded. code classification system and the modification of the threaded code technique used by a Forth programming language implementation. The classification system distinguishes threaded code designs by three elements: the interpreter, the code structure and the reference method to routines. Threaded code designs from the literature are described using the new classification scheme. The threaded code techniques of variable depth indirect threaded code and token indirect token threaded code are examined in a Forth programming language system on an INMOS IMS T222 transputer. Their design …

Investigation Of Threaded Code, K. E. Graves, Paul D. Stigall

Computer Science Technical Reports

The design, structure and performance of threaded code are examined through the development of a threaded. code classification system and the modification of the threaded code technique used by a Forth programming language implementation. The classification system distinguishes threaded code designs by three elements: the interpreter, the code structure and the reference method to routines. Threaded code designs from the literature are described using the new classification scheme. The threaded code techniques of variable depth indirect threaded code and token indirect token threaded code are examined in a Forth programming language system on an INMOS IMS T222 transputer. Their design …

Composition And Method For Radiation Synovectomy Of Arthritic Joints, D. E. Day, Gary J. Ehrhardt

Materials Science and Engineering Faculty Research & Creative Works

Radioactive microspheres for radiation synovectomy of arthritic joints in a mammal comprises a biodegradable glass material and a beta radiation emitting radioisotope chemically dissolved in and distributed substantially uniformly throughout the glass material. The biodegradable glass material may be lithium silicate, lithium aluminosilicate, lithium aluminoborate, lithium germa- nate, lithium aluminogermanate, potassium silicate, potassium aluminosilicate, potassium aluminoborate, potassium germanate or potassium aluminogermanate and the beta radiation emitting radioisotope may be samarium-153, holmium-166, erbium-169, dysprosium-165, rhenium-186, rhenium-188 or yttrium-90. Method for preparing such microspheres and for carrying out radiation synovectomy of arthritic joints utilizing such microspheres are also disclosed.

Radioactive Glass Microspheres, D. E. Day, Gary J. Ehrhardt

Materials Science and Engineering Faculty Research & Creative Works

A radioactive microsphere for radiation therapy of a mammal comprising a biologically compatible glass material containing a beta or gamma emitting radioisotope distributed substantially uniformly throughout the glass. Advantageously, the radioisotope is produced by irradiation of the microsphere.

Vertical And Angular Motion Of A Wing Model In Steady Flow: A Physical And Numerical Experimental Study, Andrew P. Johnston

Opportunities for Undergraduate Research Experience Program (OURE)

The dynamic response of a rigid wing in steady flow mounted on translational and rotational elastic supports is investigated. This study presents both a numerical and a physical experimental arrangement that can be employed to investigate the effect of a wide range of parameters on the response of the wing subjected to steady flow. An interactive computer program, which utilizes the fourth order Runge-Kutta integration scheme to solve the governing differential equations, is discussed. The program output allows for quick visualization of the change in response due to parameter changes. An experimental arrangement that utilizes the new 18" x 18" …

Study Of Joint Flexibility In Steel Frame Structures, Randy R. Frank

Opportunities for Undergraduate Research Experience Program (OURE)

Joint flexibility plays an important role in the distribution of strains and displacements in the frame structures of buildings, towers, automobiles, etc.. The objective of this project is to study the effect of flexibility (or rigidity) of two simple mechanical joints in frame structures on the stress and displacement distributions, using both experimental and analytical methods. Three welded and three bolted samples were fabricated using A-36 low carbon steel in a two column and horizontal crossmember (table) arrangement. This arrangement allows for both shear forces and axial forces in the joint. From a three element rectangular rosette strain gage attached …

Model Calculational Approach To The Conformation Of Adsorbed Polypeptide Fragments, Timothy J. Mckeon

Opportunities for Undergraduate Research Experience Program (OURE)

The focus of the paper is to examine possible conformational changes of peptides when placed in the presence of a poly-synthetic material. A major concern in the pharmaceutical industry is the loss of potency of polypeptide drug products during processing, packaging and storage. An example of this is polymer syringes being used in place of glass ones. The effect is that some protien-derived products experience structural changes due to contact with the polymer. This is otherwise known as surface denaturation. In order to understand the energetics of interfacial polypeptide systems, a calculational approach was used via the program Alchemy. The …

Development Of A Large Commercial Transport Model For A Real-Time Digital Flight Simulator, John Francis Winkler

Opportunities for Undergraduate Research Experience Program (OURE)

In order to test the adaptability of the University of Missouri-Rolla's flight simulator to different types of aircraft, a basic mathematical model of a large commercial transport aircraft is developed. The original aircraft model is based on the Cessna 210, and in order to accommodate the drastic differences between the Cessna 210 and the Boeing 747, many changes are made to the simulation code. The aircraft geometric data, stability and control derivatives, and weights data are altered to match those of the 747. Changes are made within the various subroutines to include thrust reversal, spoilers, and a variable incidence horizontal …

Measurement Of Voltage And Current In Electric Power Systems, Michael Davis

Opportunities for Undergraduate Research Experience Program (OURE)

A. B. Chance Company of Centralia, Missouri requested a study of the latest state-of-the- art technology to measure voltage and current on a normal distribution power line. (4kV - 35kV)

The particular device that A. B. Chance needs must be relatively inexpensive, $200.00 per measurement, reliable, and capable of being manufactured by them.

Four types of power line measurement techniques were investigated; electrooptics/magnetooptics, present day measurement devices, the Raychem Line Monitor, and remote voltage and current sensing (RVCS).

The remote voltage and current sensing idea is the basis of the following report.

Modeling For Supersonic Missile Wing-Body Interference Lift, Howard S. H. Ho

Opportunities for Undergraduate Research Experience Program (OURE)

During the initial phase of a missile design, a quick and simple way of estimating wing-body interference is essential. A simple panel model based on the cross flow over a cylinder is developed to estimate the effect of the body on the wing lift This model produces quick and reasonably accurate results, while little user expertise is needed. This model determines K_WB (upwash interference factor) and K_Φ (sideslip interference factor), and is applicable to infinitely thin delta and clipped delta fins on missiles in supersonic flight. The effects of the fin semivertex angle, span, taper ratio, free stream …

The Edge Strength Of Annealed And Heat-Strengthened Glass, Gregory P. Sallee

Opportunities for Undergraduate Research Experience Program (OURE)

Sadly, up until now, very little research has been conducted in the field of glass window strength. The purpose of this research, therefore, is to explore the topic of glass window strength such that we might offer some conclusive evidence as to the probable in-situ performance of structural windows. Our intention is to examine the specific phenomenon of thermally- induced stress and its effect on glass strength. J. G. Croll explains the existence of this well-documented problem. "Whenever a structure is subjected to a varying temperature distribution, or where it is prevented from free expansion, stresses will be induced that …

Identity Authentication Based On Keystroke Latencies Using Neural Networks, Angela Lammers, Sharon Langenfeld

Opportunities for Undergraduate Research Experience Program (OURE)

Most computer security systems verify the identity of a user through objects in the user's possession such as keys or magnetic cards, or through knowledge the user has, such as a password or PIN number. There are, however, two other methods of user verification, which have as yet received little or no attention. There has been some work done on the third method, recognition of physiological patterns (such as finger prints, retinal patterns, or voice patterns), but this work has been limited and requires expensive hardware to implement. The final method of user verification is through actions such as signature …

Two-Phase Flow Measurement, Glenn Brenneke

Opportunities for Undergraduate Research Experience Program (OURE)

Liquid fuel engines have many applications in today's world. Diesel, spark-ignition, and gas turbine engines, and furnaces are just a few of the many applications of liquid fuel sprays. With the rising cost of fuel and need for energy conservation it is imperative that more efficient engines be developed. Analyzing liquid fuel spray characteristics non-intrusively could unlock the door to powerful highly efficient engines in the future.

The vaporization of fuel is mandatory in liquid fuel combustion. Vaporization and the fuel to air ratio are important characteristics of the spark-ignition engine. Compression ignition is controlled by the parameters of the …

Measuring Hydrogen In Galvanized Steels, Timothy O'Hearn

Opportunities for Undergraduate Research Experience Program (OURE)

There has been much investigation in the past concerning ways to eliminate the embrittling effects of hydrogen in galvanized steel components. Such galvanized parts are used extensively in the automotive industry. One solution that is commonly used is to anneal the galvanized parts at approximately 200 degrees Celsius for 4 to 24 hours. This annealing process does restore the ductility. However, very few if any experiments have been done to measure the amount of hydrogen released and the temperature dependence of the hydrogen release. This investigation is part of an on going effort to measure the hydrogen released from galvanized …

Bundled Cable Parameters And Their Impact On Emi Measurement Repeatability, Deanna L. Weil

Opportunities for Undergraduate Research Experience Program (OURE)

This research project was 99% experimental, therefore, not many theoretical ideas will be presented. The main idea behind the project was centered around cable bundling. The effect of cable bundling using analytical measurements and data from a network analyzer was investigated.

Some Stability And Control Aspects Of A Variable Pivot Wing Configuration, Paul Vitt

Opportunities for Undergraduate Research Experience Program (OURE)

In supersonic flight, there is a large positive shift in the static margin, which causes extreme positive shifts in longitudinal stability, and is an undesirable characteristic. This paper investigates some of the stability and control aspects of an alternative configuration, that of a variable pivot wing aircraft -- an aircraft with two sets of wings, one set sweeps forward, the other set sweeps rearward. By prescribing a sweep schedule, it is desired to minimize the static margin shift with Mach number. The effects of the two lift elements -- that of mechanical shift of the center of pressure forward with …

Computer Visualization Of Irrotational Flow Over Bluff And Streamlined Bodies, Nora Okong' O

Opportunities for Undergraduate Research Experience Program (OURE)

Computer programs were developed to visualize irrotational flow over bluff bodies (circular cylinders and half-bodies) and streamlined bodies (elliptical cylinders and airfoils). The method of superposition of flows was used, with stream functions or complex velocity potentials for fundamental flows being added to obtain the flows over the bodies. For the flow over the circular cylinders, half-bodies and elliptical cylinders, the stream function was calculated directly. The flow over the airfoil was obtained by Joukowski mapping of the imaginary part of the complex velocity potential for flow over a circular cylinder.

The programs developed will be valuable learning tools for …

Development Of A Learjet Model 24d For The Umr Flight Simulator, Richard Stigall

Opportunities for Undergraduate Research Experience Program (OURE)

A flight simulator was recently developed at the University of Missouri-Rolla for a single engine aircraft. The need soon arose for a higher performance aircraft. After exploring several possibilities, a Learjet Model 24D was chosen to include the high performance aircraft.

The purpose of this project was to develop a model for the Learjet 24D. This was accomplished by examining the computer code previously written and determining the changes needed. The code for the simulation is located in various subroutines. Each subroutine was analyzed to determine if changes needed to be made. When a modification was needed, appropriate methods were …

Fourier Transform Infrared (Ftir) Spectroscopy Analysis Of Combustion Aerosol, Gary Jacquin

Opportunities for Undergraduate Research Experience Program (OURE)

In conjunction with my co-op program at McDonnell-Douglas, my current OURE project is the analysis of combustion aerosols using Fourier Transform Infrared (FTIR) Spectroscopy. Aerosol science is a very important field as it is concerned with atmospheric chemistry, atmospheric physics, climate, public health, and environmental issues.

In the Cloud and Aerosol Sciences Laboratory (CASL) at UMR, combustion aerosols are generated by an in-house designed torch or burner. The fuels, JP4 and JP5, are provided by McDonnell-Douglas. Some other commercial fuels are also used. The primary objective of my OURE project was to generate and collect combustion aerosols for chemical analysis. …

Control And Data Reduction Software For Umr Neutron Spectrometer, Matthew K. Mclaughlin

Opportunities for Undergraduate Research Experience Program (OURE)

A double-scatter time-of flight neutron spectrometer has been obtained by the Nuclear Engineering department of the University of Missouri-Rolla (UMR). As this device was an experimental prototype which was never brought to full operation, the chance to work with two of the original builders of the spectrometer at EG&G Idaho was an excellent opportunity. Part of the work being done with the detector is the development of a PC-based software package for machine control, data acquisition, and data reduction. It is this part of the project which has been supported by UMR’s Opportunities for Undergraduate Research Experience (OURE) program.

Implementation Of The Articulated Total Body (Atb) Model On An Apollo Workstation, M. F. Laudon

Opportunities for Undergraduate Research Experience Program (OURE)

The Articulated Total Body Model (ATB) is used for predicting gross segmented body response in various dynamic environments. The ATB computer program, originally written by the Department of Transportation as a Crash Victim Simulation (CVS) program, was later modified by the Calspan Corporation and More recently by the Armstrong Aerospace Medical Research Laboratory (AAMRL) to allow for aerodynamic force applications, harness belt capabilities and hyper-ellipsoidal graphical display of the modeled segments. The ATB model has been successfully used to investigate gross human body responses to bodies placed in such complex dynamic environments as high-speed aircraft ejection. This ATB model is …

Simulation Modeling In Manufacturing Cell Design, Debra A. Hunke

Opportunities for Undergraduate Research Experience Program (OURE)

The interwoven phases of the manufacturing process in Computer Integrated Manufacturing (CIM) require a carefully designed facility. Simulation modeling can be combined with other techniques to provide a rigorous methodology for CIM system design. This paper describes CIM, simulation ana their relationship. A case study demonstrates the described methodology in the design of a flexible manufacturing cell.

A Computer Simulation Of The Umr Reactor, H. Allen Wilkins

Opportunities for Undergraduate Research Experience Program (OURE)

The Opportunities for Undergraduate Research project entitled, "A Computer Simulation of the UMR Reactor" had two goals. To produce a reactor simulation to be used in creating an artificial intelligence based reactor simulation for the UMR Nuclear Reactor and to produce a means of teaching students the fundamentals of reactor operations.

The primary purpose was to create a program which would simulate all the situations one would encounter in actual reactor operation. With the simulator the artificial intelligence system could be thoroughly tested before use with actual reactor data.

This same simulator would be used as a teaching aid for …

A Computer Graphics Program For Displaying Water Molecules On A Dn3500 Apollo Workstation, Michael A. Stuller

Opportunities for Undergraduate Research Experience Program (OURE)

A computer graphics program is developed for displaying water molecule configurations on the screen of a DN3500 Apollo workstation. The motivation was to generate a fast display of output from molecular dynamics or Monte Carlo computer simulations. Input to the program consists of a listing of the Cartesian coordinates of the atomic constituents of the molecules. Options in the program include: 1) number of molecules; 2) plot size; 3) atomic radii; 4) superposition of substrate atomic positions; 5) viewing angle; and 6) color-coded and/or numbered atoms. The program is written in Fortran.

The Detection And Quantification Of Atrophic Rhinitis Using Ditigal Image Processing Techniques, Timothy Mussman

Opportunities for Undergraduate Research Experience Program (OURE)

This project focuses its attention on the detection and quantification of Atrophic Rhinitis (A.R.), a disease prevalent in pigs. A.R. causes some of the bony structure in a pig's snout to atrophy, which exposes the animal to other diseases that may effect its growth. It is studied by examining a cross section of the pig's snout. By comparing areas and perimeters of the nasal cavity to bony structures, or turbinates in the snout, one can determine the severity of the atrophy. Currently, the veterinarians diagnosis is based on a subjective analysis of the snout. The problem with this method is …