Engineering Commons^™

Evaluation Of Transient Refrigerant Migration Modeling Approach On Automotive Air Conditioning Systems, Bin Li, Steffen Peuker, Pega Hrnjak, Andrew Alleyne

Mechanical Engineering

Automotive air conditioning systems are subject to constantly changing operation conditions and steady state simulations are not sufficient to describe the actual performance. The refrigerant mass migration during transient events such as clutch-cycling or start-up bas a direct impact on the transient performance. It is therefore necessary to develop simulation tools which can accurately predict the migration of the rerrigerant mass. To this end a dynamic model of an automotive air conditioning system is presented in this paper using a switched modeling framework. Model validation against experimental results demonstrates that the developed modeling approach is able to describe the transient …

Digital Control Of Parallel-Connected Dc-Dc Converters, Taufik, Daniel Forbes, Dale Dolan, Ratna Ika Putri

Electrical Engineering

This paper presents a digitally-controlled paralleled DC-DC converter. The main objective of the digital control is to achieve load sharing while operating at close to peak efficiency over an extremely wide load range. Results from computer simulations using Simulink show the digital control could indeed accomplish the objectives, but the improvements over a single converter depend on the original efficiency characteristics of the converters. An application for a high-power electric vehicle charger utilizing this converter setup is considered.

Development Of An Integrated Project-Based Course: A Jobsite Management Class Case Study, Philip L. Barlow

Construction Management

At universities offering professional degrees, such as construction management, some programs are moving towards and exploring alternative delivery methods for achieving the curriculum’s goals and objectives. This paper describes a curriculum integrated course founded in a project-based learning environment applied to a jobsite construction management undergraduate course being taught at a major university. A course overview describing the various delivery methods used (such as lectures, reading assignments, supplemental materials, guest lecturers, lab assignments, technology, and a jobsite visit) is presented. The benefits of course integration in a construction management undergraduate curriculum are emphasized and more fully explained. The unique student …

Agricultural Water Energy Efficiency: Final Report, Charles M. Burt, Dan J. Howes, Beau Freeman

BioResource and Agricultural Engineering

Beginning in 2007, the Irrigation Training and Research Center (ITRC) at California Polytechnic State University, San Luis Obispo, contracted with the California Energy Commission’s (CEC) Public Interest Energy Research (PIER) Program to undertake a large, multi-tiered study on agricultural water energy efficiency in California. The study was broken into the following research tasks: Task 1: Administrative; Task 2.1: Irrigation district energy survey; Task 2.2: Conversion to groundwater pumping with drip/ micro irrigation systems; Task 2.3: GIS-based water scheduling and software system; Task 3: Irrigation component energy analysis; Task 4: RD&D competitive solicitation; Task 5; Technology transfer. The resulting survey, research, …

Retesting Of Liquefaction/Nonliquefaction Case Histories From The 1976 Tangshan Earthquake, R. E.S. Moss, R. E. Kayen, L-Y Tong, S-Y Liu, G-J Cai, J. Wu

Civil and Environmental Engineering

A field investigation was carried out to retest liquefaction and nonliquefaction sites from the 1976 Tangshan Earthquake in China. These sites were carefully investigated in 1978/1979 using standard penetration test (SPT) and cone penetration test (CPT) equipment, however the CPT measurements are obsolete because of the now nonstandard cone that was used at the time. In 2007 a modern cone was mobilized to retest 18 select sites that are particularly valuable because; of the intense ground shaking, high fines content, and/or the site did. Of the sites reinvestigated and carefully processed, 13 are considered accurate representative case histories. Two of …

Partial Budgeting Analysis Of Conventional Pump Over Versus Pulsair Cap Management System For A Large–Scale California Winery, Zachary Thomas Hicks

Agribusiness

The purpose of this project was to evaluate the financial feasibility of implementing an automated gas injection system from Pulsair as an alternative to the traditional pump over cap mixing technique that is used during the alcoholic fermentation stage of winemaking.

There were various costs involved in this project that were determined and explained through the use of the partial budgeting method. The costs that were thoroughly analyzed included equipment, labor, utility, and initial investment costs for the Pulsair system as well as the related pump over operation costs. After the two methods associated numbers were evaluated, they were then …

Design And Implementation Of An Automated Pick And Place System For Johanson Technology, Inc., Alex M. Felker

Industrial and Manufacturing Engineering

Johanson Technology, a capacitor and microelectronic part manufacturer, located in Camarillo, CA has forecasted a 50% increase in demand for single layer capacitors for the year 2011. Johanson chose to hire an intern to design and implement a robotic pick and place system to meet this demand. A complete automated system composed of a Stäubli RS20 robotic arm, CS8C-M Controller, and Electrosort Bowl Feeder needed to be integrated into an environment where no system currently existed. A bill of materials and parts list indicated that the entire system would be a fixed cost of $50,104. This proved to be the …

Process Improvement Of Kaiser Permanente Medical Group, Connie Chou, Brett Witherall

Industrial and Manufacturing Engineering

This report seeks to improve the operations of the Kaiser Permanente’s Central Refill Pharmacy. In particular, the need for better workstations became evident when witnessing the cluttered appearance of the packing workbenches in the facility. Furthermore, one of Kaiser’s largest problem areas is the physical strain caused by the repetitive motion required of the packing job function. A redesign of the packing workstations has been developed on Microsoft Visio in order to reduce clutter, be more space efficient, and decrease eye and arm movement associated with employee strain. The most significant additions are an automated slide that transfers packages from …

Design And Development Of Two Test Fixtures To Test The Longitudinal And Transverse Tensile Properties Of Small Diameter Tubular Polymers, Carolyn Berry

Master's Theses

Hundreds of thousands of vascular bypass grafts are implanted in the United States every year, but there has yet to be an ideal graft material to substitute for one’s own autologous vessel. Many synthetic materials have been shown to be successful vessel replacements; however, none have been proven to exhibit the same mechanical properties as native vessels, one of the most important criteria in selecting a vascular graft material. Part of this issue is due to the fact that, currently, there is no “gold standard” for testing the longitudinal and transverse tensile properties of small diameter tubular materials. While there …

Conical Probe Calibration And Wind Tunnel Data Analysis Of The Channeled Centerbody Inlet Experiment, Samson Siu Truong

Aerospace Engineering

For a multi-hole test probe undergoing wind tunnel tests, the resulting data needs to be analyzed for any significant trends.  These trends include relating the pressure distributions, the geometric orientation, and the local velocity vector to one another.  However, experimental runs always involve some sort of error.  As a result, a calibration procedure is required to compensate for this error.  For this case, it is the misalignment bias angles resulting from the distortion associated with the angularity of the test probe or the local velocity vector.  Through a series of calibration steps presented here, the angular biases are determined and …

Geomagnetic Compensation For Low-Cost Crash Avoidance Project, John C. Torres

Master's Theses

The goal of this work was to compensate for the effects of the Earth’s magnetic field in a vector field magnetic sensor.  The magnetic sensor is a part of a low-cost crash avoidance system by Stephane Roussel where the magnetic sensor was used to detect cars passing when it was mounted to a test vehicle.  However, the magnetic sensor’s output voltage varied when it changed orientation with respect to the Earth’s magnetic field.  This limited the previous work to only analyze detection rates when the test vehicle travelled a single heading.  Since one of the goals of this system is …

Evaluation Of An Innovative System For Improving Readability Of Passive Uhf Rfid Tags Attached To Reusable Plastic Containers, Jay A. Singh, S. Roy, B. Roesner

Industrial Technology and Packaging

Radio frequency identification (RFID) is a contactless identification technology that has proven to work well in conjunction with reusable plastic containers (RPCs). The impact of this technology on returnable containers has been explored by several past studies. This study evaluates an innovative system for improving readability of passive UHF RFID tags in conjunction with RPCs. The system involves an energy transfer device (ETD), which when attached to the RPCs, passively transfers radio frequency signals to interior regions of a unitized load thereby improving the readability of all RFID tags attached to the RPCs. This study included an evaluation of the …

Design And Analysis Of A Wind Energy Harvesting Circuit Using Piezoelectric Polymers, Jameson J. Thornton

Master's Theses

This thesis investigates a relatively new method for harvesting wind energy by using flexible piezoelectric polymers with additional sails to increase their ability to harvest wind energy. This paper also introduces a new topology deemed the “stacked buck” that allows for multiple inputs to a system with a single output. Derivations and analysis detail the workings of the “stacked buck” with a laboratory test to show a working model. This paper also reports another experiment done in a wind tunnel to analyze the capability of the piezoelectric polymers as sources to the “stacked buck” topology with measurements of the power …

Assessment Of State Composting Regulations In The United States, Nazli Yesiller, Samuel A. Vigil, James L. Hanson

Civil and Environmental Engineering

This investigation was conducted to identify the current "status of state composting regulations in the U.S. using an extensive survey administered to regulators from all 50 states. Questions were included regarding: background information on composting: status of regulations: regulatory details including feedstock specific provisions and regulatory framework with respect to MSW regulations: details regarding type, properties, and amount of materials handled by composting activities; outgoing materials and storage of materials; type of composting facilities: initial development of the regulations; level of rigor of regulations: enforcement and reporting requirements; efficiency and level of satisfaction with regulations: permitting fees; and modifications to …

Green Building Policy And School Performance, S. Kelting, M. Montoya

Construction Management

The movement to construct high performance “green” buildings has had unprecedented market growth and continues to become a mainstream practice for constructing schools in the United States. This paper will consider how the results of government requirements for higher performance school buildings may affect the health and performance of students. The research focuses on educational leaders’ perceptions of how they would prioritize green building strategies based on recent governmental policy that requires building green schools. There is clear and compelling evidence that schools currently built to specific green standards of indoor environmental quality, specifically lighting, result in healthier and more …

Scale Modeling Of Cessna 172, Chee-Woon Kim

Aerospace Engineering

This report describes how the scale-model aircraft can be built when the Reynolds number is out of range for using dynamic similitude method. Due to lack of time and budget for designing an actual model for testing, Cessna 172 was used to calculate the size of the temporary scale-model aircraft. The method that was used for this project was matching aerodynamic coefficients such as drag coefficient or lift coefficient of the prototype and the model. Based on this method, the takeoff distance, landing distance and the rate of climb of the model came out to be 218 ft, 91 ft …

Seismic Response Of Peaty Organic Soils As A Levee Foundation Material, Robb E.S. Moss, Justin C. Hollenback

Civil and Environmental Engineering

The dynamic response of peaty organic soils is not well understood but its poor competency as an engineering material is well known. Its use as a foundation material is generally avoided through careful selection of project location, or removal and replacement with more suitable material. In certain situations peaty organic soils are unavoidable because of prior land use and subsequent development of infrastructure. In a delta environment levees are often found to be overlying peaty organic deposits, the California Bay Delta and New Orleans levee systems are two important examples. The Bay Delta is in a seismically active area and …

Shake Table Testing Of Seismic Soil-Foundation-Structure-Interaction, Robb E.S. Moss, Steven Kuo, Victor Crosariol

Civil and Environmental Engineering

This research involves shake table testing of 1g scale models that mimic the coupled seismic response of a structure on a shallow mat foundation and the foundation soil (termed soil‐foundation‐structure‐interaction or SFSI). In previous research, SFSI effects have been quantified through analytical models, numerical analyses, and limited field data. This research is working towards increasing the amount of empirical data through scale model shake table testing. A suite of earthquake times histories are considered in evaluating a 10^th scale soil‐structure model using a flexible wall barrel on a 1‐D shake table. San Francisco Young Bay Mud (YBM) is used …

Polymeric Splint And Rapid-Setting Polyurethane, Lanny Griffin, Dane Robert Jones

Biomedical Engineering

A splint includes a first container capable of being wrapped about an item to be supported and a second container capable of containing a multiple part mixture during a mixing operation. The second container being capable of delivering the mixture into the first container, wherein the mixture hardens to form a support structure. A method for using the splint is also disclosed.

Development And Delivery Of An Integrated Project-Based Jobsite Management Undergraduate Course, Philip L. Barlow

Construction Management

At universities offering professional degrees, such as construction management, some programs are moving towards and exploring alternative delivery methods for achieving the curriculum's goals and objectives. This article describes an integrated and project-based learning Jobsite Construction Management course being taught at a major university. A course overview describing the various delivery methods used (such as lectures, reading assignments, supplemental materials, guest lecturers, lab assignments, technology, and jobsite visits) is presented. The benefits of vertical and horizontal course integration in a project-based learning environment are emphasized and more fully explained. A class survey was conducted over two quarters to assess the …

Investigation Of The Behavior Of Free-Standing Gabions In Seismic Regions, Amy Ransom

Master's Theses

This thesis investigates the behavior of free-standing gabion walls in areas of mild seismicity. To investigate this behavior, three walls of varying internal cable patterns were constructed at a quarter-scale. These walls were tested with a mass shaker, and mode shapes, tone extractions, and damping ratios were calculated. A modal analysis was conducted using design spectra created from a suite of seven earthquakes from countries bordering Kenya. The corresponding lateral forces to these spectral displacements were found, and the restoring eccentricities from the soil restoring force were backed out through a summation of moments. All analysis was experimentally done due …

Exploring Trade-Offs In Auv Controller Design For Shark Tracking, Louis James Bertsch Iv

Master's Theses

This thesis explores the use of an Autonomous Underwater Vehicle (AUV) to track and pursue a tagged shark through the water. A controller was designed to take bearing and range to the shark tag and then control the AUV to pursue it.

First, the ability of a particle filter to provide an accurate estimation of the location of the shark relative to the AUV is explored. Second, the ability of the AUV to follow the shark's path through the water is shown. This ability allows for localized environmental sampling of the shark's preferred path. Third, various path weightings are used …

Material Weight Station Optimization Senior Project, Douglas Peters, Michael Eng

Industrial Technology and Packaging

The main principle of all industry is that “time is money”. This senior project focuses on reducing operation times for Specialty Silicone Fabricators (SSFab) materials weighing station. Currently SSFab is set up so that multiple operators check the weights of materials. This is done to guarantee the accuracy of the readings and maintain tight quality control. This project will focus on eliminating the need of multiple weight checkers as a way to save time and ultimately save money.

Through detailed research and studies it has been determined that the most appropriate solution to this problem is a weight checking software …

Gauge Repeatability And Reproducibility Study For A Bulge Test Fixture For Corrugated Boxes, Anthony J. Hall

Industrial Technology and Packaging

This senior project evaluates the measurement variation within a corrugated container bulge tester by utilizing a gauge repeatability and reproducibility study. Bulge is a type of deformation containers experience when subject to compressive forces such as stacking or internal forces due to under- and over-packaging. Both compressive and internal forces can accelerate the failure of a container by causing panels to flex and flutes to buckle, compromising structural integrity. Additionally, variable environmental conditions such as temperature and humidity can magnify the effect bulge has on a container, speeding up the failure rate of a container.

Design Of Online Student Fee Committee Proposal Information System, Kenneth Cairns, Gregory (Greg) Jacobson

Industrial and Manufacturing Engineering

The purpose of this project is to overhaul the IME department’s Student Fee Committee (SFC) proposal system. A web enabled database was designed in order to improve this system. A significant amount of time was spent researching different programming languages, paradigms, and frameworks in order to determine the most logical approach to the system redesign. After a few false leads, it was determined that the most appropriate solution to the problem was to design a C# based web form application using asp.NET technology, developed in Microsoft Visual Studio. A mockup was created in Access in an attempt to determine if …

Discrete Event Simulation Manual: Manufacturing Applications, Brian T. Hughes

Industrial and Manufacturing Engineering

Simulation, specifically discrete event simulation, is a useful tool for industrial and manufacturing engineers when dealing with system analysis. Currently, manufacturing engineers are only exposed to simulation for only a few weeks of their curriculum at Cal Poly. A series of labs are directed by a teacher’s assistant on how to complete a successful simulation experiment. However, there is no text available for student use during this demanding learning period. The simulation learning process involves learning a software program called ProModel, which students with little experience are expected to code, run, and interpret data from complex systems. By creating a …

Optimization Of Screw Cap Process For E & J Gallo Winery, Robert Trent Latimer

Industrial and Manufacturing Engineering

This project takes a microscopic look at all raw material, machinery, and practices that effect the screw cap process of wine products in order to highlight and eliminate the causes of defects. The approach for this project involves the analysis of process capability for raw material to achieve its required dimensions. This project also displays methods of attaining appropriate machinery settings, and provides a basis for operating standards. Many quality engineering applications are used throughout this study, revealing the decision process for analyzing said applications.

The studies in this project found uncontrolled dimensions in the suppliers’ caps and bottles and …

Reactive Routing In Hidra Networks, Scott Michael Marshall

Computer Engineering

In recent years, the Internet has grown so large that the future scalability of the Internet has become a major concern. The two primary scalability concerns are the size of the forwarding table and the ability for BGP to converge while distributing hundreds of thousands of routes.

HIDRA is a new Internet routing architecture that is backwards-compatible with existing routing technologies and protocols that focuses on feasibility-of-implementation. HIDRA remedies the first Internet scalability concern by proposing a means to reduce the number of entries in the default-free zone (DFZ) forwarding table.

This project extends HIDRA by designing a complete reactive …

Pipeline Design For Reclaimed Spill Water For West Stanislaus Irrigation District, Daniel Bays

BioResource and Agricultural Engineering

The goal of this project was to design a pipeline that could be installed to replace an existing drain in West Stanislaus Irrigation District.  The pipeline would give the district the ability to divert drain water back into their delivery system or send water down the existing drain.

The design attempted to use pipe and material the district already has and provided construction drawings and installation instructions for the construction of this design in the future.

Economic Analysis Of Reverse Osmosis Desalination Of Water For Agricultural Irrigation Applications, Ashley Hemping

BioResource and Agricultural Engineering

The combination of an ever-increasing population and a diminishing usable water supply threatens the sustainability of humanity’s existence on a global scale, especially in California, where agriculture is so integral to the state’s economy.  Due to widespread recognition of this problem, there has been a growing trend in the development of alternative water resources, one of which involves the desalination of salt or brackish waters.  Several different desalination technologies exist, including microfiltration, multi-stage flash, and multi-effect distillation.

This senior project investigates the economic viability of implementing reverse osmosis desalination for treatment of agricultural wastewater or other unusable water sources.  These …