Engineering Commons^™

Asce 7–05 Design Rule For Relative Strength In A Tall Buckling-Restrained Braced Frame Dual System, Lisa J. Aukeman

Master's Theses

In mid- to high-rise structures, dual systems (DS) enable a structural designer to satisfy the stringent drift limitations of current codes without compromising ductility. Currently, ASCE 7-05 permits a variety of structural systems to be used in combination as a dual system yet the design requirements are limited to the following statement: Moment frames must be capable of resisting 25% of the seismic forces while the moment frames and braced frames or shear walls must be capable of resisting the entire seismic forces in proportion to their relative rigidities.

This thesis assesses the significance of the 25% design requirement for …

Optimization Of Point-Of-Use Water Treatment Device For Disaster Relief, Margaret June Herzog

Master's Theses

Point-of-use (POU) drinking water treatment is a common method of providing drinking water in disaster relief situations when critical water infrastructure is damaged. In these cases, POU treatment devices can be used to treat local water until relief organizations set up more permanent water provision methods. One such POU technology is PŪR^® Purifier of Water, a combined coagulation/flocculation and disinfection chemical treatment sachet produced by Procter & Gamble. PŪR^® has been shown to treat contaminated water to meet water quality standards and guidelines set by the U.S. EPA for water purifiers and by the World Health Organization and …

Water And Air Quality Performance Of A Reciprocating Biofilter Treating Dairy Wastewater, Seppi Matthew Henneman

Master's Theses

ABSTRACT

Water and Air Quality Performance of a Reciprocating

Biofilter Treating Dairy Wastewater

Seppi Matthew Henneman

Agricultural non-point source pollution is the leading water quality problem in surface water and the second leading problem in ground water in the US.  Among the contaminants, nutrients (such as nitrogen, phosphorus, potassium) can be transported from agricultural fields when cropland is not managed properly.  In California, dairy manure application to cropland has become tightly regulated with the goal of decreasing such nutrient pollution.  Dairies unable to balance their manure nutrient supply with cropland application area may benefit from a nitrogen removal technology.  One …

An Investigative Study Of Gurney Flaps On A Naca 0036 Airfoil, Gregory F. Altmann

Master's Theses

This project examined the effect of Gurney flaps on a 2D, 2-ft chord NACA 0036 airfoil in the Cal Poly 3’x4’ low speed wind tunnel at 25 m/s.  It also covered the numerical simulation of the experiment in computational fluid dynamics (CFD).  During the study, problems with the wind tunnel data were seen.  After a careful diagnosis, the problem was traced to dirty flow conditioners which were subsequently replaced.

Five Gurney flaps at 1, 2, 3, 4, and 5% of the chord were tested.  The Gurney flaps had the effect of eliminating the lift reversal effect and lowering the profile …

A Study Into The Use Of Microprocessor Relays For Motor Operated Valve (Mov) Electrical Protection In Nuclear Power Plants, James Andrew Tuccillo

Master's Theses

Motor Operated Valves (MOVs) are electro-mechanical components used to isolate, divert, or introduce fluid flow. The use of microprocessor relays for actuator motor electrical protection within nuclear power plants is the focus of this thesis and is implemented by providing a new and enhanced protection scheme that provides the adequate conservatism necessary to ensure valve operation while still maintaining electrical safety and continued operational availability. The comprehensive protection scheme is designed around an advanced microprocessor relay that has the ability to simulate the thermal overload conditions of a motor operating into a destructive thermal region. Through laboratory testing, the validity …

Off-Grid Photovoltaic System Design Project, Brian Duffy

Electrical Engineering

This project uses the BP SX 150S solar panel to charge a 12 V battery. This battery powers an AIMS 400 W Modified Sine Wave Inverter to provide 120 V RMS AC power to a load of up to 40 W. Inverter efficiency was measured at different load conditions. A control circuit was implemented to prevent overcharging or over-discharging of the battery, by disconnecting it from the panel or the load, respectively. The control circuit turn-on and cutoff voltages were measured versus battery voltage, and the on-resistance of the MOSFET switches was measured for various load currents. A table of …

A Study Of Osteocyte Apoptosis By Region And Quadrant In Murine Cortical Bone, Jessica Kristen Chan

Master's Theses

ABSTRACT

A Study of Osteocyte Apoptosis by Region and Quadrant in Murine Cortical Bone

Jessica Kristen Chan

Osteocytes undergo apoptosis to spatially and temporally initiate bone remodeling.  This study investigates the distribution of apoptotic osteocytes within different quadrants and regions of cortical bone and compares the frequency of osteocyte apoptosis to regional factors associated with bone remodeling.  Specifically, the quantity of apoptosis was compared to levels of the bone morphagenic protein antagonists noggin and gremlin.  Samples of unloaded right tibial bone obtained from C57/Bl/6 mice underwent TUNEL staining for apoptotic osteocytes and were counterstained with methyl green to detect osteocyte …

Universal Engineering Programmer – An In-House Development Tool For Developing And Testing Implantable Medical Devices In St. Jude Medical, Khoa Tat Do

Master's Theses

During development and testing of the functionality of the pacemaker and defibrillator device, engineers in the St. Jude Medical Cardiac Rhythm Management Division use an in-house development tool called Universal Engineering Programmer (UEP) to ensure the device functions as expected, before it can be used to test on an animal or a human during the implantation process.  In addition, some applications of UEP are incorporated into the official releases of the device product.  UEP has been developed and used by engineers across departments in the St. Jude Medical Cardiac Rhythm Management Division (CRMD).  This thesis covers the flexible and reusable …

Two Element Linear Strength Vortex Panel Method, Clifton A. Cox

Aerospace Engineering

A linear strength vortex panel method was developed to predict the C_p and C_l for a lifting two element airfoil. The linear strength vortex panel method was first validated against thin airfoil theory and experimental data for a single NACA 2412 airfoil. At 2 degrees angle of attack, the linear strength vortex panel method predicted a C_l of about 0.49. Experimental data and thin airfoil theory gave C_l estimations of 0.45 and 0.22 respectively. The Matlab code was then modified to accept a two element airfoil. The two key modifications were the separation of the two …

The Biomechanics Of Varied Proximal Locking Screw Configurations In A Synthetic Model Of Proximal Third Tibial Fracture Fixation, Philip R. Wolinsky, Douglas Dennis, Brett D. Crist, Shane Curtiss, Scott J. Hazelwood

Biomedical Engineering

Objective: To determine if 1) angularly stable devices created by compressing (‘‘locking’’) proximal locking screws to intramedullary nails using end caps or compression screws or 2) increasing the number of proximal screws from two to three increases the stiffness of intramedullary constructs that stabilize proximal third tibia fractures in a nonosteopenic bone model.

Methods: Four proximal locking screw configurations were examined in a synthetic composite tibia model with a 2-cm gap simulating a comminuted proximal third tibia fracture with no bony contact: 1) two proximal screws not compressed to the nail; 2) one of two proximal screws compressed to …

The Fresh Express Lean Changeover Project, Mario Borbas

Industrial Technology and Packaging

In the current economic turmoil, industry leaders across the globe are resorting to means of increasing efficiency without having a large initial investment.  Lean manufacturing principles have been adopted by companies because of its ability to increase throughput, lower overhead, reduce waste, and increase the overall quality of products.  The value of lean manufacturing solutions has been increasing in the past decade and continues to increase into 2011.

This project is centered on a current situation regarding a changeover process that has recently been made more efficient. The goal is to create new ways to make this same process even …

Material Reduction In Corrugated Containers For The Fresh Produce Industry, Justin Patterson

Industrial Technology and Packaging

In the fresh produce industry, corrugated containers must be made to provide adequate protection throughout the product life cycle. In response to increasing materials costs in the corrugated industry, companies are focusing upon developing more efficient packaging designs.  The scope of this project focuses on presenting alternative corrugated packaging designs for the fresh produce industry.  Included are one piece designs, three piece bliss designs and alternative material exploration.  This project presents the performance of new solutions by exploring their compressive strength before and after exposure to humidity.

High-Resolution, Non-Contact Angular Measurement System For Psa/Rsa, Ronald D. Sloat

Master's Theses

A non-contact angular measurement system for Pitch Static Attitude (PSA) and Roll Static Attitude (RSA) of hard disk drive sliders is designed and built. Real-time sampling at over 15 KHz is achieved with accuracy of +/- 0.05 degrees over a range of approximately 2-3 degrees. Measuring the PSA and RSA is critical for hard drive manufacturers to control and improve the quality and reliability of hard drives. Although the hard drive industry is able to measure the PSA and RSA at the subassembly level at this time, there is no system available that is able to measure PSA/RSA at the …

Multiple-View Planetary Photogrammetry And Its Visualization, Kyle D. Husmann

Electrical Engineering

During the summer of 2010, Dr. Taemin Kim and Kyle Husmann jointly developed a novel new algorithm to generate topographical maps of planetary surfaces using a multiple-view photogrammetry approach. To evaluate and debug the algorithm, a program called mvpgui was developed to visualize and examine the objective function. After verifying the correct operation of the algorithm and mvpgui with synthetic data, it is run with real orbital data from the Apollo 15 mission. The results confirm the validity of the multiple-view algorithm as well as demonstrate the value of objective function visualization.

Led Spotlight, Eric Toussaint

Electrical Engineering

This report details the development and construction of an LED spotlight useable in a theatrical or architectural setting.  In depth background information, initial design concepts, lighting instrument specifications, assembly, testing, and conclusions from results are highlighted in this document.  Project goals include efforts to support more energy efficient lighting in the arts and general lighting applications and a decrease in overall costs for energy used in all dramatic and architectural lighting applications.

Standardization For Retail Facility Layout For Patagonia, Inc., Derek King

Industrial and Manufacturing Engineering

The purpose of this project is to create a standard layout for Patagonia retail stores. Currently, Patagonia has no standard layouts to follow when they update or open a new store; this has resulted in improper layouts and not fulfilling customers’ needs. This project will develop a way for Patagonia to solve both of these problems based on statistical engineering. The outcome of this project will result in a standard way for determining the optimal layout for new or updated Patagonia retail stores while meeting the business needs of the location.

Hardy Diagnostics Facility Redesign, Jamie W. Lam

Industrial and Manufacturing Engineering

This senior project is a facilities design for the plate production room at Hardy Diagnostics. This project was completed using a systematic layout planning approach. The main reason for this redesign was to consolidate all plate line production into one room. This would ensure better visability for the managers. After the project was defined, the different departments were established and the relationships between those departments were found. The space requirements needed for those departments were then measured out to also include the aisle widths and any machinery or carts needed to complete each function. Having determined all requirements for this …

Probabilistic Fault Displacement Hazard Analysis For Reverse Faults And Surface Rupture Scale Invariance, Zachary E. Ross

Master's Theses

p.p1 {margin: 0.0px 0.0px 0.0px 0.0px; font: 12.0px 'Times New Roman'}

A methodology is presented for evaluating the potential surface fault displacement on reverse faults in a probabilistic manner. This methodology follows the procedures put forth for Probabilistic Fault Displacement Hazard Analysis (PFDHA). Empirical probability distributions that are central to performing a PFDHA are derived from field investigations of reverse faulting events. Statistical analyses are used to test previously assumed properties of scale invariance with respect to magnitude for normalized displacement. It is found that normalized displacement is statistically invariant with respect to magnitude and focal mechanism, allowing for the …

Predicting Articular Cartilage Constituent Material Properties Following In Vitro Growth Using A Proteoglycan-Collagen Mixture Model, Michael Stender

Master's Theses

      A polyconvex continuum-level  proteoglycan Cauchy stress function was developed based on the continuum electromechanical Poisson-Boltzmann unit cell model for proteoglycan interactions. The resulting proteoglycan model was combined with a novel collagen fibril model and a ground substance matrix material to create a polyconvex constitutive finite element model of articular cartilage. The true collagen fibril modulus , and the ground substance matrix shear modulus , were varied to obtain the best fit to experimental tension, confined compression, and unconfined compression data for native explants and explants cultured in insulin-like growth factor-1 (IGF-1) and transforming growth factor-β1 (TGF-β1).  Results indicate …

The State Of Software Engineering Maturity And Licensure, Travis Lawrence Dean

Master's Theses

IEEE-CS is pursuing licensing for software engineers, but ACM believes that software engineering is too immature, and regulating the profession would be premature. In 1996, Norman Gibbs and Gary Ford from Carnegie Mellon University performed a qualitative survey of the maturity of the software engineering profession. I apply this model to the present state of the art in software engineering and analyze the results for 2010. I analyze the maturity of software engineering to determine that the profession is not yet ready for licensure. This is not because the infrastructure of software engineering is too immature, but because we have …

Mitigating Moisture Susceptibility In Hot-Mix Asphalt Concrete, Tom P. Nguyen

Master's Theses

Moisture damage in asphalt pavement has always been a problem for drivers, bicyclists, and pedestrians. The primary objective of this study is to evaluate moisture susceptibility of Hot-Mix Asphalt (HMA) and to investigate mitigation techniques using different antistripping agents. Three types of antistripping agents were used in this research investigation. Two of which are chemical based and the other is hydrated lime. The two types of liquid antistripping agents used in this study include Arr Maz CC LOF-6500 and Arr Maz CC XL-9000. These two liquid antistripping agents were tested at 0.25%, 0.50%, and 0.75%. Hydrated Lime was tested at …

Influence Of Nozzle Pressure, Standoff Distance, And Reinforcing Steel Cage On Water Jetting Of Cidh Pile Anomalies, Matthew Jason Schaffer

Master's Theses

The effectiveness of removing anomalous material from cast-in-drilled-hole (CIDH) piles by water jetting was examined.  The primary objectives of this research were to examine how reinforcing steel influences water jetting and to evaluate how jetting pressures and standoff distance from the material surface affect water jetting of concrete type materials and PVC tubing.  The experimental work consisted of water blasting submerged test specimens using rotary jets, nozzles, pumping equipment, and testing procedures currently used in construction practice.  The concrete test specimens were comprised of ring- and cylinder-shaped samples, containing materials with compressive strengths of approximately 160 and 3,600 psi.  Typical …

Tower-Tracking Heliostat Array, Joel T. Masters

Master's Theses

This thesis presents a method of tracking and correcting for the swaying of a central receiver tower in concentrated solar production plants.  The method uses a camera with image processing algorithms to detect movement of the center of the tower.  A prototype was constructed utilizing a CMOS camera connected to a microcontroller to control the movements of three surrounding heliostats.  The prototype uses blob-tracking algorithms to detect and correct for movements of a colored model target.  The model was able to detect movements in the tower with average error of 0.32 degrees, and was able to correctly orient the surrounding …

Artificial Neural Networking As A Decision Tool For Natural Gas Investment, Micah D. Denecour

Master's Theses

With the growing interest in the Marcellus Shale and its natural gas deposits, there are opportunities to purchase and hold land for investment purposes. A robust decision tool is needed to help guide investors towards the most profitable properties. Artificial neural networks have many unique benefits that make them an ideal candidate for this purpose.

The artificial neural networks created in this study had nine independent variables. Combinations of these nine variables were created to describe 300 theoretical properties available for purchase. Each of these properties were then evaluated by an expert in the field and given a score from …

Integration Of Aeroservoelastic Properties Into The Nasa Dryden F/A-18 Simulator Using Flight Data From The Active Aeroelastic Wing Program, Alexander Wong Chin

Master's Theses

Aircraft structures have varying stiffness levels making them flexible. Consequently, this elastic property becomes increasingly important at high speeds affecting the flight dynamics of the aircraft.  In high speed aircraft such as the F/A-18, elastic structural properties must be accounted for to ensure confidence in predicted flight dynamics in order to avoid adverse aeroelastic phenomena throughout flight.

Data from the F/A-18 Active Aeroelastic Wing (AAW) program was used to create aeroservoelastic (ASE) models at varying flight conditions. The discretized ASE models were integrated into the NASA Dryden F/A-18 simulator in parallel with the traditional 6-DOF (degrees-of-freedom) flight dynamics calculations to …

Compressor Performance Map Generation And Testing Per Sae J1723, Jeffrey Lee Freeman

Aerospace Engineering

A MATLAB program was written to plot compressor performance maps for a set of test data that was collected in accordance with SAE J1723 at Vortech Engineering, Inc. Paxton Automotive Corp.'s N2500 supercharger was used as a case example for the program, which was carried through from test stand installation to finalized compressor performance map. A sequence was also developed to interpolate the efficiency of the compressor for a given operational setting. The program was shown to be a great improvement from the previously applied technique for accomplishing the same tasks; it is more accurate in plotting the given data, …

Electric Guitar Amplifier With Digital Effects, Shawn Garrett

Computer Engineering

During the course of this project, the research and development of an electric guitar amplifier was undertaken. This amplifier is divided into three distinct sections. The power distribution circuitry provides the proper voltages to safely operate all necessary components. The DSP and digital effects stage provides processing and allows the user to add digital effects to the original guitar sound. The amplification stage increases the power of the input signal to drive a loudspeaker. Due to several setbacks throughout the course of this project, the overall amplifier was not completed. All three of the sections were developed to working functionality, …

3-D Terrain Mapping And Navigation Using A Laser Range Finder, Matthew L. Azevedo, Matthew Parilla, Kevin K. Parsons

Mechanical Engineering

The purpose of this Senior Project is to develop and implement a three-dimensional mapping and navigation system utilizing laser technology on a robotic platform.  The sponsor of this project, Synbotics® Incorporated, currently has an obstacle avoidance system only operating in a single horizontal plane.  This limits the mapping and navigation ability of the robot because objects below and above this plane are not accounted for.  A three-dimensional system is needed to allow the robot to better navigate and map an area by accounting for these objects in the third dimension and avoiding collisions.  Keith Guy, Synbotics® Chief Executive Officer, requested …

An Exploratory Model For Predicting Post-Consumer Recycled Pet Content In Pet Sheets, Dong Ho Kang, Rafael Auras, Keith Vorst, Jay Singh

Industrial Technology and Packaging

An exploratory model for determining post-consumer recycled polyethylene terephthalate (PET) content in PET sheets for one specific stream of mechanically recycled PET (RPET) was developed. Six kinds of PET sheets with varying percent of virgin (V) and recycled (R) PET contents (i.e., 100V, 80V20R, 60V40R, 40V60R, 20V80R, and 100R PET) were commercially extruded. The optical, thermal, physicomechanical and barrier properties of the PET sheets were evaluated as function of RPET content. Differences were found between the sheets for UV and visible light absorption in the regions 200–350 nm and 670–700 nm, respectively. Intrinsic viscosities of 100V and 100R PET sheets …

Investigation Of Pmma Cement Penetration In Prepared Femoral Heads With A Longitudinal Slot For Hip Resurfacing Arthroplasty, Scott Snyder

Biomedical Engineering

Hip resurfacing arthroplasty is becoming increasingly popular in younger, active patients due to its preservation of natural biomechanics. Failure of these implants can be very traumatic and potentially life threatening. The role of cement penetration in early implant failure is not yet known, and must be investigated. This study specifically investigates the effects of a 5mm by 5mm longitudinal channel on cement penetration into the femoral head. High-density open-cell reticulated vitreous carbon foam cylinders and Huntsman Pro-cast® 20 implants based on the Birmingham Hip Resurfacing implant were used. It was determined cement penetration was increased in the area immediately surrounding …